Panasonic CW-XC55HU User Manual

INSTALLATION AND OPERATING INSTRUCTIONS
Room Air Conditioner
Model: CW-XC55HU
Please read these operating instructions thoroughly before using your air conditioner and keep for future reference.
For U.S. customers: For assistance, please call: 1-800-211-PANA(7262) or Register your product at : http://www.panasonic.com/register
CW382820391M
R
TEMPTEM
P
F
DRY
ECONOMY
FAN
COOL
O P
E R A
T I O
N
O P
E R A
T IO
N
OFF/ON
F A
N S P E
E
D
TIM
E
R
M
O
D
E
About the Controls on the Air Conditioner
Features and Installation
Before you call for service...
2
Safety Precautions
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of the unit.
Dealer's Name
Date Purchased
Staple your receipt here for proof of purchase.
Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner.
You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.
READ THIS MANUAL
CAUTION
• Contact an Authorized Service Center for repair or maintenance of this unit.
• The air conditioner is not intended for use by young children or invalids without supervision.
• Young children should be supervised to ensure that they do not play with the air conditioner.
Safety Precautions
Safety Precautions .............3
About the Controls on the Air Conditioner
Controls..............................5
Air direction ........................7
Care and Maintenance ......7
Features and Installation
Features .............................8
Window Requirements .......9
Electrical Data ..................12
Electrical Safety ...............13
Before You Call For Service...
Normal Operation.............14
Abnormal Operation .........14
WARNING
3

Safety Precautions

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed:
Incorrect operation will cause harm or damage. The seriousness is classified by the following indications.
Because of the weight of the product, it is recommended that you have a helper to assist in the installation.
Use Caution! Sharp Edges! See Warning, page 4.
WARNING : This symbol indicates the possibility of death or serious injury.
CAUTION
:
This symbol indicates the possibility of injury or damage to property only.
Meanings of symbols used in this manual are as shown below.
Be sure not do this.
Be sure to follow the instructions.
Plug in the power plug properly.
• Otherwise, it will cause electric shock or fire due to heat generation.
Do not operate or stop the unit by inserting or pulling out the power plug.
• It will cause electric shock or fire due to heat generation.
Do not damage or use an unspecified power cord.
• It will cause electric shock or fire.
If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
Do not modify the length of the power cord or use an extension cord.
• It will cause electric shock or fire due to heat generation.
Do not operate with wet hands or in a damp environment.
• It will cause electric shock.
Do not direct air flow at room occupants.
• This could lead to health problems.
Sharp edges
When the air filter is to be removed, do not touch the metal parts of the unit.
They are sharp and may cause an injury.
Do not clean the air conditioner with water.
Water may enter the unit and degrade the insulation. It may cause an electric shock.
When the unit is to be cleaned, switch the unit off, and unplug it.
Since the fan rotates at high speed during operation, it may cause an injury.
Do not operate the unit without the air filter or when the front intake grille has been removed.
It could cause dust to accumulate on the heat exchanger.
Do not put a pet or house plant where it will be exposed to direct air flow.
This could injure the pets or plants.
Do not use the unit for any other purpose than its intended use.
Do not use this air conditioner to preserve precision devices, food, pets, plants, or art objects. It may cause deterioration of quality, etc.
Do not operate switches with wet hands
.
It may cause an electric shock.
Do not apply an insecticide or flammable spray.
It may cause a fire or damage of the cabinet.
SHARP EDGES!
Use caution when handling the case. Grip it firmly and do not allow it to slip while holding it.
Use heavy gloves to handle the case if necessary.
4
Safety Precautions

About the Controls on the Air Conditioner

5
About the Controls on the air conditioner
The controls will look like the following.

Controls

hr
F
FAN
COOL
DRY
ECONOMY
FAN
SPEED
MODE
TEMP
OPERATION
OFF/ON
TIMER
ON/OFF TIMER
- STOPPING OPERATION
Every time you push this button, when the unit is operating, timer is set as follows. (1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours Cancel)
The Setting Temperature will be raised by 2°F (1°C) 30 min. later and by 2°F (1°C) after another 30 min.
- STARTING OPERATION
Every time you push this button, when the unit is not operating, timer is set as follows. (1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours Cancel)
MODE
Every time you push this button, it will toggle between COOL, ECONOMY, FAN and DRY.
POWER
To turn the unit ON, push the button. To turn the unit OFF, push the button again.
This button takes priority over any other buttons.
When you first turn it on, the unit is on the High cool mode
and the temperature is set at 72°F (22°C).
TEMPERATURE SETTING
This button can automatically control the temperature of the room. The temperature can be set within a range of 60°F (16°C) to 86°F (30°C) by 1°F (1°C). Select a lower number for a lower temperature in the room.
FAN SPEED
Every time you push this button it is set as follows. {High(F2)
Low(F1)
High(F2)...}.
DRY
When this unit is in dry mode, the fan rotates at low speed. The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on and the unit checks the room air temperature to set itself.
6
About the Controls on the Air Conditioner
Remote controller
Precaution:
The Remote Controller will not function properly if strong light strikes the sensor window of the air
conditioner or if there are obstacles between the Remote Controller and the air conditioner.
1. Remove the cover from the back of the
remote controller
2. Insert two batteries.
Be sure that the (+) and (-) directions are correct.
Be sure that both batteries are new.
3. Re-attach the cover.
Do not use rechargeable batteries. Such batteries differ from standard dry cells in shape, dimensions, and performance.
Remove the batteries from the remote controller if the air conditioner is not going to be used for an extended length of time.
Keep the remote control away from infants and small children to prevent them from accidentally swallowing the batteries.
How to Insert Batteries
OPERATION
TEMP
TIMER
MODE
ECONOMY
FAN SPEED
ROOM TEMPERATURE SETTING BUTTON
ECONOMY
ON/OFF TIMER BUTTON
OPERATION BUTTON
FAN SPEED SELECTION BUTTON
OPERATION MODE SELECTION BUTTON
To turn the air conditioner ON, push the button. To turn the air conditioner OFF, push the button again.
This button takes priority over any other buttons.
When you first turn it on, the air conditioner is on the High cool mode and the temp. at 72°F (22°C).
Every time you push this button, it will toggle between COOL, ECONOMY, FAN
and DRY.
If you push this button, the fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is needed.
You can set the time when the unit will turn on or turn off automatically by pressing the timer button. If the unit is in operation, this button controls the time it will be turned off. If the unit is in off state, this button controls the time it will start. Every time you push this button, the remaining time will be set as follows:
- STOPPING OPERATION
Every time you push this button, when the air conditioner is operating, timer is set as follows : (1Hour
2Hours → 3Hours → 4Hours → 5Hours → 6Hours → 7Hours →
8Hours
9Hours → 10Hours → 11Hours → 12Hours → 0Hour → 1Hour → 2Hours → ...)
The Setting Temperature will be raised by 2°F (1°C) 30 min. later and by 2°F (1°C) after another 30 min.
- STARTING OPERATION
Every time you push this button, when the air conditioner is not operating, timer is set as follows : (1Hour
2Hours → 3Hours → 4Hours → 5Hours → 6Hours → 7Hours →
8Hours → 9Hours →10Hours → 11Hours → 12Hours → 0Hour → 1Hour → 2Hours → ...)
Every time you push this button, it is set as follows. {High(F2)
Low(F1) → High(F2)...}.
This button can automatically control the temperature of the room. The temperature can be set within a range of 60°F to 86°F by 1°F. (16°C to 30°C by 1°C) Select a lower number for a lower temperature in the room.
7
About the Controls on the Air Conditioner
Do not force open or open too far (about 56°)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.
• TO CLEAN FILTER
The air filter will become dirty as it removes dust from the inside air. It should be washed at least every 2 weeks. If the air filter remains full of dust, the air flow will decrease and the cooling capacity will be reduced, possibly damaging the unit.
1. Pull the inlet grille forward and pull out the air filter. (Fig. 1)
2. Wash the air filter in warm 104°F (40°C) water. Be sure to shake off all the water before replacing the filter.
• CLEANING THE AIR CONDITIONER
The front grille and inlet grille may be wiped with a cloth dampened in a mild detergent solution. (Fig. 2) The cabinet may be washed with mild soap or detergent and lukewarm water, then polished with a liquid wax used for appliances.
To ensure continued peak efficiency, the condenser coils (outside of unit) should be checked periodically and cleaned if clogged with soot or dirt from the atmosphere.
• HOW TO REMOVE THE FRONT GRILLE
1. Pull the inlet grille forward.
2. Remove the screw securing the front grille. (Fig. 3)
3. Push the grille up from the bottom and pull the top of the grille away from the case as the top tabs lift out of their slots. (Fig. 4)
Additional controls and important information.

Care and Maintenance

Air Direction

• ADJUSTING THE AIR DIRECTION USING THE HORIZONTAL AIR-DEFLECTOR CONTROL
Using the control tabs, the air flow can be directed to the left, right, straight ahead, or any combination of these directions.
8

Features and Installation

1
8
5
3 2
6
T E
M P
T E
M P
F
DRY
ECONOMY
FAN
COOL
O P
E R A
T I O N
O P
E R A
T I O N
OFF/ON
F A
N
S
P E
E D
TIM
ER
M
O
D E
T E
M P
T E
M P
F
DR Y
EC
O
NOM
Y
FA
N
C OO
L
O P E
R
A T
IO N
O P E
R
A T
I O N
O
F F/O
N
F A
N S P E
E
D
T IM
E
R
M O
D
E
7
9
4
10
Wire net
Groove
Learning parts name prior to installation will help you understand the installation procedure.

Features

How to install wire net on the back side of the cabinet (Optional : CW353020031B)
Insert the rear grill wire ends into the 4 respective slots provided along the groove at the back of unit.
1. CABINET
2. HORIZONTAL AIR DEFLECTOR
3. COOL AIR DISCHARGE
4. FRONT GRILLE
5. INLET GRILLE
6. AIR FILTER
7. CONTROL BOARD
8. AIR INTAKE
9. UPPER GUIDE
10. REMOTE CONTROLLER
Features and Installation
9
Features and Installation
OUTDOORSINDOORS
INNER
SILL
OUTER
SILL
INNER
SILL
WOOD STRIP MOUNTED
ON TOP OF INNER SILL
1"
WOOD STRIP
FOR
L
BRACKET
3
/4"
CLEARANCE
STORM
WINDOW
FRAME
OUTDOORSINDOORS
OUTER
SILL
TYPE B: Qty:5
(WOOD SCREW)
HARDWARE
TYPE A: Qty:11
(SHORT SCREW)
TYPE C: Qty:3
(L BRACKET)
TYPE E: Qty:1
(SASH SEAL)
(Not adhesive backed)
TYPE D: Qty:1 (SEAL STRIP)
(Adhesive backed)
TYPE F: Qty:2
(GUIDE PANEL)
TYPE G: Qty:1
(SUPPORT BRACKET)
25/64"
(10mm)
5/8"
(16mm)
DRAIN PIPE
Qty:1
NOTE: All supporting parts should be secured to firm wood, masonry, or metal.
1. This unit is designed for installation in standard double hung windows with actual opening widths of 22" to 36". The upper and lower sash must open sufficiently to allow a clear vertical opening of 13" from the bottom of the sash to the window stool.
2.If a storm window presents interference, fasten a 2" wide wood strip to the inner window sill across
the full width of the sill. The wood strip should be thick enough to raise the height of the window sill so that the unit can be installed without interference by the storm window frame. See Fig. 5-2. The top of the wood strip should be approximately
3
/4" higher than the storm window frame (STORM WINDOW FRAME) or wood strip (OUTDOORS) to help condensation to drain properly to the outside.
3. Install a second wood strip (approximately 18" long by 1
1
/2" wide and same thickness as first strip) in the center of the outer sill flush against the back off the inner sill. This will raise the L bracket as shown in Fig. 5-2.
4. The thickness of the second wood strip may not be the same as the first wood strip. The thickness of the second wood strip must be defined to keep the
3
/4 inch distance between the
inner sill or the top of the first wood strip and the outer sill.

Window Requirements

Installation
Fig. 5-1
Fig. 5-2
10
Features and Installation
ROOM SIDE
CENTER LINE
INNER SILL
SEAL STRIP (TYPE D)
CENTER LINE
OUTSIDE
INSIDE
L
BRACKET
OUTER SILL
INNER SILL
TYPE A
8"
8"
CENTER LINE
SEAL
WINDOW FRAME
BOTTOM GUIDE
ABOUT
1/4"
L
BRACKET
UPPER GUIDE
TYPE A
TYPE A
A. BEFORE INSTALLATION
1. Insert the guide panels into the guides of the air conditioner. Fasten the curtains to the unit with screws (TYPE A), as shown Fig. 6.
2. Cut the adhesive-backed seal strip (TYPE D) to the window width.
Remove the backing from the seal strip and attach the seal strip to the underside of the bottom window. (Fig. 7)
B. NOW START INSTALLATION
1. LOCATING UNIT IN A WINDOW
Open the window and mark center line on the center of the inner sill, as shown in Fig. 8.
2. ATTACH L BRACKET
a. Install the L brackets behind the inner window
sill, with short side of bracket as shown. Use the 2 screws (TYPE A) provided.
b. The bracket helps to hold the unit securely in
place. Be sure to place bracket edge flush against back of inner sill. See Fig. 9.
3. INSTALL THE AIR CONDITIONER IN THE WINDOW
a. Carefully lift the air conditioner and slide it into
the open window. Make sure the bottom guide of the air conditioner drops into the notches of the L bracket. See Fig. 9.
IMPORTANT :
When the air conditioner drops into the L bracket, the air conditioner will be centered in window opening as shown in Fig. 10.
b. While steadying the air conditioner, carefully
bring the window sash down behind the upper guide of the air conditioner, as shown in Fig. 11.
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
During the following step, hold unit firmly until window sash is lowered to top channel behind side panel frames. Personal injury or property damage may result if unit falls from window.
CAUTION
Loading...
+ 21 hidden pages