Operating Instructions
QUICK GUIDE
Air Conditioner
Model No.
Indoor Unit Outdoor Unit
CS-KC9NKH-3 CU-KC9NKH-3
CS-KC12NKH-3 CU-KC12NKH-3
ENGLISH
Before operating the unit, read these operating
instructions thoroughly and keep them for future
reference.
QUICK GUIDE
© Panasonic Appliances Air-Conditioning Malaysia
Sdn. Bhd. 2012. Unauthorized copying and distribution
is a violation of law.
F568406
Thank you for purchasing
TABLE OF CONTENTS
WARNING
CAUTION
WARNING
Air Inlet
Air Outlet
Air Outlet
Air Inlet
NOTE
OPERATION CONDITION
Panasonic Air Conditioner
TABLE OF CONTENTS
SAFETY PRECAUTIONS
REMOTE CONTROL
INDOOR UNIT
TROUBLESHOOTING
INFORMATION
QUICK GUIDE
BACK COVER
NOTE
The illustrations in this manual are for
explanation purposes only and may
differ from the actual unit. They are
subjected to change without notice for
future improvement.
OPERATION CONDITION
Use this air conditioner under the following
temperature range
Temperature (°C)
COOLING
Max. 32 23
Min. 16 11
Temperature (°C)
COOLING
Max. 43 26
Min. 16 11
* DBT: Dry bulb temperature
* WBT: Wet bulb temperature
2
2~3
4~5
5
7
7
Indoor
*DBT *WBT
Outdoor
*DBT *WBT
SAFETY PRECAUTIONS
To prevent personal injury, injury to others, or property damage, please
comply with the following.
Incorrect operation due to failure to follow instructions below may cause
harm or damage, the seriousness of which is classifi ed as below:
WARNING
CAUTION
The instructions to be followed are classifi ed by the following symbols:
INDOOR UNIT AND OUTDOOR UNIT
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
Please consult authorized dealer or specialist to clean the internal
parts, repair, install, remove and reinstall the unit. Improper
installation and handling will cause leakage, electric shock or fi re.
Confi rm to authorized dealer or specialist on usage of specifi ed
refrigerant type. Using of refrigerant other than the specifi ed type
may cause product damage, burst and injury etc.
Do not install the unit in a potentially explosive or fl ammable
atmosphere. Failure to do so could result in fi re.
Do not insert your fi ngers or other objects into the air
conditioner indoor or outdoor unit, rotating parts may
cause injury.
Do not touch the outdoor unit during lightning, it may cause electric
shock.
Do not expose yourself directly to cold air for a long period to avoid
excess cooling.
Do not sit or step on the unit, you may fall down
accidentally.
Indoor Unit
Remote
Control
Outdoor
Unit
This sign warns of death or
serious injury.
This sign warns of injury or
damage to property.
This symbol denotes an action
that is PROHIBITED.
These symbols denote an
actions that is COMPULSORY.
WARNING
Air Inlet
Power
Supply
Air Outlet
Air Inlet
Air Outlet
CAUTION
WARNING
WARNING
REMOTE CONTROL
Do not allow infants and small children to play
with the remote control to prevent them from
accidentally swallowing the batteries.
POWER SUPPLY
Do not use a modifi ed cord,
joint cord, extension cord or
unspecifi ed cord to prevent
overheating and fi re.
To prevent overheating, fi re or electric shock:
• Do not share the same power outlet with other
equipment.
• Do not operate with wet hands.
• Do not over bend the power supply cord.
• Do not operate or stop the unit by inserting or
pulling out the power plug.
If the supply cord is damage, it must be replaced
by the manufacturer, its service agent or similarly
qualifi ed persons in order to avoid a hazard.
It is strongly recommended to be installed with
Earth Leakage Circuit Breaker (ELCB) or Residual
Current Device (RCD) to prevent electric shock
or fi re.
To prevent overheating, fi re or electric shock:
• Insert the power plug properly.
• Dust on the power plug should be periodically
wiped with a dry cloth.
Stop using the product if any abnormality/failure
occurs and disconnect the power plug or turn off
the power switch and breaker.
(Risk of smoke/fi re/electric shock)
Examples of abnormality/failure
• The ELCB trips frequently.
• Burning smell is observed.
• Abnormal noise or vibration of the unit is
observed.
• Water leaks from the indoor unit.
• Power cord or plug becomes abnormally hot.
• Fan speed cannot be controlled.
• The unit stops running immediately even if it is
switched on for operation.
• The fan does not stop even if the operation is
stopped.
Contact your local dealer immediately for
maintenance/repair.
This equipment must be earthed to prevent
electrical shock or fi re.
Prevent electric shock by switching off the power
supply and unplug when:
- Before cleaning or servicing.
- Extended non-use.
- Abnormally strong lightning activity.
CAUTION
INDOOR UNIT AND OUTDOOR UNIT
Do not wash the indoor unit with water, benzene,
thinner or scouring powder to avoid damage or
corrosion at the unit.
Do not use for preservation of precise equipment,
food, animals, plants, artwork or other objects. This
may cause quality deterioration, etc.
Do not use any combustible equipment in front of
the airfl ow outlet to avoid fi re propagation.
Do not expose plants or pet directly to airfl ow to
avoid injury, etc.
Do not touch the sharp aluminium fi n,
sharp parts may cause injury.
Do not switch ON the indoor unit when waxing the
fl oor. After waxing, aerate the room properly before
operating the unit.
Do not install the unit in oily and smoky areas to
prevent damage to the unit.
Do not dismantle the unit for cleaning purpose to
avoid injury.
Do not step onto an unstable bench when cleaning
the unit to avoid injury.
Do not place a vase or water container on the
unit. Water may enter the unit and degrade the
insulation. This may cause an electric shock.
Do not open window or door for long time during
COOL/DRY mode operation.
Ensure drainage pipe is connected properly and
keep drainage outlet clear of gutters, containers
or does not immersed in water to prevent water
leakage.
After a long period of use or use with any
combustible equipment, aerate the room regularly.
After a long period of use, make sure the
installation rack does not deteriorate to prevent the
unit from falling down.
REMOTE CONTROL
Do not use rechargeable (Ni-Cd) batteries.
It may damage the remote control.
To prevent malfunction or damage of the remote
control:
• Remove the batteries if the unit is not going to be
used for a long period of time.
• New batteries of the same type must be inserted
following the polarity stated.
POWER SUPPLY
Do not pull the cord to disconnect the plug to
prevent electric shock.
3
AIR SWING
FAN SPE
ED
MODE
TEMP
OFF/
ON
TIMER
SET
CANCEL
ON
OFF
1
2
3
SET CLOCK
RESET
OFF
TIMER
ON
TIM
ER
FAN
SPE
ED
AIR
SWI
NG
AUTO
COOL
DRY
AUTO
COMF
ORT
ECONAVI
REMOTE CONTROL
Maximum
distance: 8m
INDICATOR
POWER
TIMER
ECONAVI/
AUTO COMFORT
Human activity
sensor
Remote
Control display
6
3
2
8
9
11
(Green)
(Orange)
(Green)
Press the remote control’s button
1
TO TURN ON OR OFF THE UNIT
• Please be aware of the OFF indication on the remote
control display to prevent the unit from starting/stopping
improperly.
2
TO SET TEMPERATURE
• For cool and dry modes, the range of temperature for
selection is 16°C ~ 30°C.
• Operating the unit within the recommended temperature
could induce energy saving.
COOL mode : 26˚C ~ 28˚C.
DRY mode : 1˚C ~ 2˚C lower than room temperature.
3
TO SELECT OPERATION MODE
AUTO mode - For your convenience
• Unit selects the operation mode according to the room
temperature.
• Once auto mode is selected, the unit will operate at the
standard setting temperature.
Room
temperature
Operation mode
23˚C & above Cool 25˚C
Below 23˚C Dry 22˚C
• Press for “HI” to +2˚C or for “LO” to -2˚C to the
standard setting temperature.
COOL mode - To enjoy cool air
• Use curtains to screen off sunlight and outdoor heat to
reduce power consumption during cool mode.
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling
1
7
operation.
4
TO SELECT FAN SPEED (3 OPTIONS)
4
FAN SPEED
5
• For AUTO, the indoor fan speed is automatically adjusted
according to the operation mode.
TO ADJUST VERTICAL AIRFLOW DIRECTION
5
10
(5 OPTIONS)
AIR SWING
• Keeps the room ventilated.
• In COOL/DRY mode, if AUTO is set, the louver swing
up/down automatically.
Standard setting
temperature
4
TO SET THE TIMER
S
O
6 7
NOTES
O
I
TO MONITOR HUMAN
PRESENCE & ACTIVITY
FOR ENERGY SAVING &
ECONAVI/
AUTO COMFORT
COMFORT
ECONAVI
AUTO
COMFORT
Heat Source & Movement
COOL/DRY Mode
Set Temperature
Set Fan Speed
To optimize energy saving
To maximize comfort
HighLow
Normal
+1°C
-1°C
+1 tap*
+1 tap
None
+2°C
≤ Medium
Fan
* For first 15 minutes or until set temperature is reached.
• The human activity sensor may not detect moving objects
further than 7m away or beyond detection angle.
• The human activity sensor sensitivity is infl uenced by
indoor unit location, movement speed, temperature range,
etc.
• The human activity sensor may:
- Mistakenly detects an object with heat source &
movement similar to human, such as pets, etc. as
human being.
- Mistakenly detects as non-heat source & movement if
a person stays motionless for certain period of time.
Press and hold for 5 seconds to dim or restore the
8
unit’s indicator brightness.
TO SET THE TIMER
• To turn ON or OFF the unit at a preset time.
ON
1
OFF
Select ON or
OFF timer
• To cancel ON or OFF timer, press
press
CANCEL
.
2
ET
Set the time Confi rm
N
OFF
or
then
• When ON Timer is set, the unit may start earlier (up
to 15 minutes) before the actual set time in order to
achieve the desired temperature on time.
• Timer operation is based on the clock set in the
remote control and repeats daily once set. For clock
setting, please refer to Remote Control Preparation
on the back cover.
• If timer is cancelled manually or due to power failure,
you can restore the previous setting (once power is
resumed) by pressing
SET
.
Press and hold for approximately 10 seconds to
9
show temperature setting in °C or °F
10
Press to restore the remote control’s default setting.
AUT
COMFORT
ECONAV
,
NOTES
• Can be activated in all modes and can be cancelled
11
Not used in normal operations.
by pressing the respective button again.
• Cannot be selected at the same time.
5
INDOOR UNIT
CLEANING INSTRUCTIONS
HINT
• Switch off the power supply and unplug before cleaning.
CAUTION
CLEANING INSTRUCTIONS
• Do not use benzene, thinner or scouring powder.
• Use only soap ( pH7) or neutral household detergent.
• Do not use water hotter than 40°C.
• Do not touch the aluminium fi n, sharp parts may cause injury.
HINT
• To ensure optimal performance of the unit, cleaning
maintenance has to be carried out at regular intervals.
Please consult authorized dealer.
4
2
3
5
6
7
1
INDOOR UNIT
• Wipe the unit gently with a soft, dry cloth.
2
FRONT PANEL
Remove Front Panel
• Raise and pull to remove the front panel.
• Wash gently and dry.
Close Front Panel
• Press down both ends of the front panel to close it
securely.
3
REMOTE CONTROL RECEIVER
4
ALUMINIUM FIN
5
HUMAN ACTIVITY SENSOR
6
HORIZONTAL AIRFLOW DIRECTION LOUVER
• Manually adjustable.
7
VERTICAL AIRFLOW DIRECTION LOUVER
• Do not adjust by hand.
6
1
8
9
10
8
• Use when remote control is misplaced or a malfunction
occurs.
Press once. Auto
Press and hold until 1 beep is heard,
then release.
Press the button to turn off.
9
• Clean the fi lter whenever necessary.
• Wash/rinse the fi lter gently with water to avoid damage
to the fi lter.
• Dry the fi lter thoroughly under shade, away from fi re or
direct sunlight.
• Replace the fi lter every 10 years or replace any
damaged fi lter.
Part no.: CZ-SA22P
10
• Air fi lter cleaning is required every two weeks.
• Wash/rinse the fi lters gently with water to avoid damage
to the fi lter surface.
• Dry the fi lters thoroughly under shade, away from fi re or
direct sunlight.
• Replace any damaged fi lters.
5
HUMAN ACTIVITY SENSOR
• Do not hit or violently press the sensor or
poke it with a sharp object. This can lead to
damage and malfunction.
• Do not place large objects near the sensor
and keep away heating units or humidifi ers
from the sensor’s detection area. This may
lead to sensor malfunction.
AUTO OFF/ON BUTTON
Action Mode
ANTI-BACTERIAL FILTER
Anti-bacterial fi lter.
AIR FILTERS
Cooling
TROUBLESHOOTING
The following symptoms do not indicate malfunction.
SYMPTOM
CAUSE
Check the following before calling for servicing.
SYMPTOM
CHECK
The following symptoms do not indicate malfunction.
SYMPTOM
Mist emerges from indoor unit. ► • Condensation effect due to cooling process.
Water fl owing sound during operation. ► • Refrigerant fl ow inside the unit.
The room has a peculiar odor. ► • This may be due to damp smell emitted by the wall,
Indoor fan stops occasionally during automatic fan speed
setting.
Operation is delayed a few minutes after restarting. ► • The delay is a protection to the unit’s compressor.
Outdoor unit emits water/steam. ► • Condensation or evaporation occurs on pipes.
TIMER indicator is always on. ► • The timer setting repeats daily once set.
Cracking sound during operation. ► • Changes of temperature caused the expansion/
Check the following before calling for servicing.
SYMPTOM
Cooling operation is not working effi ciently. ► • Set the temperature correctly.
Noisy during operation. ► • Check if the unit has been installed at an incline.
Remote control does not work.
(Display is dim or transmission signal is weak.)
The unit does not work. ► • Check if the circuit breaker is tripped.
The unit does not receive the signal from the remote
control.
carpet, furniture or clothing.
► • This helps to remove the surrounding odours.
contraction of the unit.
• Close all doors and windows.
• Clean or replace the fi lters.
• Clear any obstruction at the air inlet and air outlet vents.
• Close the front panel properly.
► • Insert the batteries correctly.
• Replace weak batteries.
• Check if timers have been set.
► • Make sure the receiver is not obstructed.
• Certain fl uorescent lights may interfere with signal
transmitter. Please consult authorized dealer.
CAUSE
CHECK
INFORMATION
FOR SEASONAL INSPECTION AFTER EXTENDED NON-USE
• Checking of remote control batteries.
• No obstruction at air inlet and air outlet vents.
• After 15 minutes of operation, it is normal to have the following
temperature difference between air inlet and air outlet vents:
Cooling: ≥ 8°C
FOR EXTENDED NON-USE
• Turn off the power supply and unplug.
• Remove the remote control batteries.
Information for Users on Collection and Disposal of Old Equipment and used Batteries
[Information on Disposal in other Countries
outside the European Union]
These symbols are only valid in the European
Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for
the correct method of disposal.
NON SERVICEABLE CRITERIAS
TURN OFF POWER SUPPLY AND UNPLUG then
please consult authorized dealer under the following
conditions:
• Abnormal noise during operation.
• Water/foreign particles have entered the remote
control.
• Water leaks from Indoor unit.
• Circuit breaker switches off frequently.
• Power cord becomes unnaturally warm.
• Switches or buttons are not functioning properly.
Note for the battery symbol (bottom
two symbol examples):
This symbol might be used in combination
with a chemical symbol. In this case it
complies with the requirement set by the
Directive for the chemical involved.
Pb
7
MODE
OFF/ON
TEMP
Remote Control Preparation
QUICK GUIDE
Remote Control Preparation
1
2
3
5
2
6
SET
3
CANCEL
MODE
OFF/ON
TEMP
4
TIMER
ON
1
OFF
SET CLOCK RESET
1
AUTO
DRY COOL
Select the desired mode.
2
Start/stop the operation.
3
Select the desired temperature.
Pull out
1
Insert AAA or R03 batteries (can be used ~ 1 year)
2
Close the cover
3
Press CLOCK
4
Set time
5
Confi rm
6
1
AUTO
COOL
DRY
OFF
TIMERONTIMER
OFF/ON
ECONAVI
MODE
TEMP
TIMER
ON
1
2
OFF
SET CLOCK RESET
FAN
SPEED
AIR
SWING
AUTO
COMFORT
FAN SPEED
AIR SWING
SET
3
CANCEL
2
3
Printed in Malaysia
Panasonic Corporation
Website: http://panasonic.net/
F568406
ST1011-0
Loading...