Panasonic cs-e9nkua installation

Order No: PHAAM1111085C1

Indoor Unit Outdoor Unit

CS-S9NKUA

CS-S12NKUA

WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the products dealt with in this service information by anyone else could result in serious injury or death.

PRECAUTION OF LOW TEMPERATURE

In order to avoid frostbite, be assured of no refrigerant leakage during the installation or repairing of refrigerant circuit.

CU-S9NKUA

CU-S12NKUA

10. Installation Instruction

10.1 S9NKUA S12NKUA

10.1.1 Select the Best Location

10.1.1.1 Indoor Unit

x Do not install the unit in excessive oil fume area

such as kitchen, workshop There should not be any heat source or

near the unit.

There should not be any obstacles blocki circulation.

A place where air circulation in the room

A place where drainage can be ea A place where noise prevention is taken

onsiderat

Do not install the unit near the door way.

x x Ensure the spaces indicated by arrows from the

wall, ceili Recommended installation height for ind

shall be at least 8.2 ft.

ion.

ng, fence or other obstacles

and etc.

steam

ng the air

is good.

sily done.

into

oor unit

10.1.1.2 Outdoor Unit

x If an awning is built over the unit to prevent direct

sunli

ght or rain, be careful that heat radiat

the con

x There should not be any animal or plant which

coul Keep the spaces indicated by arrows from

ceiling, fence or other obstacles.

Do not place any obstacles sho

If piping length is over the [piping length addition adde

denser is not obstru

d be affected by hot air discharg

rt circuit of the discharg

al gas], additional refrigerant sh

d as shown in the tabl

cted.

which may cause a

ed air.

ion from

ed.

wall,

for

ould be

10.1.2 Indoor/Outdoor Unit Installation Diagram

Example: For S9NKUA If the unit is installe

additional refrigerant should be 1.64 oz .... (32.8 - 24.6)

ft x 0.2 oz/ft = 1.64 oz.

d at 32.8 ft distance, the quantity of

10.1.3 Indoor Unit

10.1.3.1 How to Fix Installation Plate

The mounting wall shall be strong and solid enough to prevent if from the vibration.

The ce

ntre of installation plate should be at more than c at right and left of the wall. The distance from installation plate edge to ceiling should more than d. From installation plate left edge to unit’s left side is e. From installation plate right edge to unit’s right side is f.

B : For left side piping, piping connection for liquid should be about g from this line.

: For left side piping, piping connection for gas should be about h from this line.

1 Mount the installation plate on the wall with 5 screws or more (at least 5 screws).

(If mounting the unit on the concrete wall, consider using anchor bolts.) o Always mount the installation plate horizontally by aligning the marking-off line with the thread and us

a level gaug

2 Drill the piping plate hole with ø2 ¾” hole-core drill.

o Line according to the left and right side of the installation plate. The meeting point of the extended lin

the cente above. The h respectively.

Drill the piping hole at either the right or the left and the hole should be slightly slanting to the outdoo side.

r of the hole. Another method is by putting measuring tape at position as sh

ole center is obtained by measuring the distance namely 5 1/16” for left and righ

10.1.3.2 To Drill a Hole in the Wall and

Install a Sleeve of Piping

1 Insert the piping sleeve to the hole. 2 Fix the bushing to the sleeve. 3 Cut the sleeve until it extrudes about 19/32”

from the wall.

ing

e is

own in the diagram

t hole

Finish by sealing the sleeve with putty or caulking compound at the final stage.

+ 6 hidden pages