Order No. MAC0301002C8
Room Air Conditioner
CS-A12CTP CU-A12CTP5
CS-A18CTP CU-A18CTP5
CS-A24CTP CU-A24CTP5
CONTENTS
Page Page
1 Functions 2
2 Product Specifications
3 Dimensions
4 Refrigeration Cycle Diagram
5 Block Diagram
6 Wiring Diagram
7 Operation Details
8 Operating Instructions
9 Installation Instructions
10 Servicing Information
11 Troubleshooting Guide 51
5
12 Technical Data
11
13 Exploded View
14 Replacement Parts List
13
15
15 Exploded View
16 Replacement Parts List
17
19
17 Exploded View
35
18 Replacement Parts List
19 Electronic Circuit Diagram
39
50
© 2003 Matsushita Industrial Corp. Sdn. Bhd.
(11969-T). All rights reserved. Unauthorized copying
and distribution is a violation of law.
53
55
56
57
58
59
60
61
AUT
HEA
COOL
DR
AN
SPEED
OFF
OFF
ON
ON
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
1 Functions
Remote Control
OFF / ON I
H
B
OFF/ON
FAN
SPEED
H
O
T
U
A
T
A
E
H
L
O
O
C
Y
R
D
A
TEMP
Self illuminating
MODE SLEEP
S
B
A
TIMER
N
A
/C
T
E
S
T
C
E
L
E
Operation OFF / ON Room Temperature Setting
N
A
F
A
AIR SWING
M
L
E
C
RESET
TEMP.
D
E
E
P
S
O
T
U
L
A
U
N
A
button
MODE
FAN SPEED
AIR SWING
Operation Mode Selection
•
•
•
•
AUTO
HEAT
COOL
DRY
Automatic Operation Mode
Heating Operation Mode
Cooling Operation Mode
Soft Dry Operation Mode
Indoor Fan Speed Selection
• Low Fan Speed
• Medium Fan Speed
• High Fan Speed
•
AUTO
Airflow Direction Control
•
AUTO
•
MANUAL
Automatic Fan Speed
Automatic Airflow Direction
Control
Airflow Direction Manual
Control
TIMER
SLEEP
Heating, Cooling, Soft Dry Operation.
• Temperature Setting (16°C to 30°C)
Automatic Operation
Operation with 2°C higher than
•
standard temperature.
• Operation with standard temperature.
•
Operation with 2°C lower than
standard temperature.
12-hour Timer Setting
•
SELECT
To select delay OFF Timer,
ON Timer, OFF/ON Timer
and ON/OFF Timer
•
•
•
SET/CANCEL
To set hours setting
To set hours setting
To start delay OFF and ON
timer, cancellation
Sleep Mode Operation OFF / ON
2
Indoor Unit
AUTO
OFF / ON
Automatic Operation Button
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
Indoor Fan Speed Control
• Press for < 5s to operate Automatic
operation mode.
(Used when the remote control cannot be used.)
• Press continuously for 5s or < 10s to
operate Test Run/Pump down. “Beep”
sound will be heard at the 5th second.
(Used when test running or servicing.)
• Press continuously for 10s and above to
omit or resume the remote control signal
receiving sound. “Beep, beep” sound will
be heard at the 10th second.
Operation Indication Lamps (LED)
•
POWER
(Green) ......... Lights up in operation,
blinks in Automatic
Operation Mode judging,
deice operation and
hotstart.
•
SLEEP
(Orange) .........Lights up in Sleep Mode
Operation.
•
TIMER
(Orange) ....... Lights up in Timer
Setting.
•
AIR SWING
(Orange) ... Lights up in Auto Air
Swing Mode Operation.
Operation Mode
• Heating, Cooling, Soft Dry and Automatic
Mode.
Random Auto Restart Control
• Operation is restarted randomly after
power failure at previous setting mode.
• High, Medium and Low.
• Automatic Fan Speed Mode
– Heating : Fan speed varies from Me →
SSLo in accordance with
indoor heat exchanger.
– Cooling : Fan rotates at Hi, Me and
SLo speed.
– Soft Dry : Fan rotates at Lo- speed.
Airflow Direction Control
• Automatic air swing and manual adjusted
by remote control for vertical airflow.
• Manually adjusted by hand for horizontal
airflow.
Time Delay Safety Control
•
Restarting is inhibited for appro. 3 minutes.
7 Minutes Time Save Control
• Cooling Operation only.
30 Minutes Time Save Control
• Heating Operation only.
Hot-Start Control
• At Heating Operation the indoor fan will
operate at SLo speed when indoor heat
exchanger temperature reaches 30°C.
Anti-Freezing Control
• Anti-Freezing control for indoor heat
exchanger. (Cooling and Soft Dry)
Sleep Mode Auto Control
• Indoor Fan operates refer to Indoor Fan
Speed.
• Operation stops after 8 hours.
Anti Cold Draft Control
• The indoor fan operates at SSLo when the
indoor heat exchanger temperature is low.
(During Heating mode thermal off)
Anti-Dew Formation Control
• Anti-Dew Formation Control for indoor unit
discharge area.
3
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
Outdoor Unit
CU-A12CTP5
Compressor Reverse Rotation
Protection Control
• To protect compressor from reverse
rotation when there is a instantaneous
power failure.
Overload Protector
• OLP to protect the compressor for A12CT
only.
Inner protector for A18CT & A24CT only.
60 Secs. Forced Operation Control
• Once the compressor is activated, it does
not stop within the first 60 secs.
However, it stops immediately with remote
control stop signal.
CU-A18CTP5
CU-A24CTP5
Deice Control
• To prevent frosting at outdoor heat exchanger. (Only for Heating Operation)
Overload Protection Control
• Outdoor fan stops when indoor heat
exchanger temperature rises to 51°C and
above, and restarts when the indoor heat
exchanger temperature drops to 49°C and
below (A12CT).
• Compressor stop when indoor heat
exchanger temperature reaches 65°C
(A12CT), 68°C (A18CT & A24CT).
(Heating Operation Only)
Outdoor Fan Operation Control
A18 / 24CT
• 4-pole induction motor (2 speed).
• For Cooling or Soft Dry operation
Hi-speed ............... When outdoor
temperature reaches to 31°C.
Lo-speed .............. When outdoor
temperature reaches to 29°C.
• For Heating operation
Hi-speed ............... When outdoor
temperature reaches to 13.5°C.
Lo-speed .............. When outdoor
temperature reaches to 15.5°C.
• For Over-heating Protection, the Fan is
switched ON or OFF depending on the
piping temperature and the outdoor
temperature.
A12CT
• 6-pole induction motor (1 speed).
Compressor Protection Control
• If the outdoor fan motor is not running after
compressor starts for 50 secs., compressor
will stop. (Cooling and Soft Dry Operation
only).
4-Way Valve Control
• When the unit is switched to “OFF” during
Heating Operation, 4-way valve stays at
Heating position for 5 minutes.
4
2 Product Specifications
Unit CS-A12CTP CU-A12CTP5
Power Source Phase
V
Cycle
Cooling Capacity kW
Btu/h
kcal/h
Heating Capacity kW
Btu/h
kcal/h
Moisture Removal l/h
Pint/h
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
Single
220 - 230
50
3.52 - 3.52
12,000 - 12,000
3,030 - 3,030
4.00 - 4.00
13,600 - 13,600
3,440 - 3,440
2.0
4.2
Airflow Method OUTLET
INTAKE
Air Volume Indoor Air (Lo) m3/min (cfm) Cooling: 7.5 (260) - 7.5 (260)
Indoor Air (Me) m3/min (cfm) Cooling: 8.9 (310) - 8.9 (310)
Indoor Air (Hi) m3/min (cfm) Cooling: 9.7 (340) - 9.7 (340)
Noise Level dB (A) Cooling: High 39 - 39; Low 33 - 33
Power Noise Level dB (A) Cooling: High 52 - 52
Electrical Data Input Power W Cooling: 1,090 - 1,160
Running Current A Cooling: 5.1 - 5.2
EER W/W 3.23 - 3.03
COP W/W 3.70 - 3.51
Starting Current A 16.9
Piping Connection Port
(Flare piping)
Pipe Size
(Flare piping)
Drain
Hose
Power Cord Length
Number of core-wire
Dimensions Height inch (mm) 21 - 9/32 (540) 21 - 9/32 (540)
Net Weight lb (kg) 40 (18) 82 (37)
Compressor Type — Rotary (1 cylinder)
Air Circulation Type SIROCCO Propeller Fan
Inner diameter mm 20 —
Length m 0.6 —
Width inch (mm) 40 - 1/2 (1,028) 30 - 23/32 (780)
Depth inch (mm) 7 - 7/8 (200) 11 - 13/32 (289)
Motor Type — Induction (2-poles)
Rated Output kW — 0.93
Material ABS STYLAC 181 PP
Motor Type Induction (4-poles) Induction (6-poles)
Input W 69.8 - 79.0 65 - 73
Rated Output W 29 33
Fan Speed Low rpm Cooling: 640 - 640
Medium rpm Cooling: 760 - 760
High rpm Cooling: 830 - 830
inch
inch
inch
inch
m 1.8
Heating: 7.5 (260) - 7.5 (260)
Heating: 8.9 (310) - 8.9 (310)
Heating: 9.7 (340) - 9.7 (340)
Heating: High 39 - 39; Low 33 - 33
SIDE VIEW TOP VIEW
32.5 (1,150) - 33.0 (1,160)
Cooling: High 48 - 49
Heating: High 48 - 49
Heating: High 52 - 52
Heating: 1,080 - 1,140
Heating: 5.0 - 5.1
G ; Half Union 1/2”
L ; Half Union 1/4”
G (gas side) ; 1/2”
L (liquid side) ; 1/4”
3 (1.0 mm
Heating: 640 - 640
Heating: 760 - 760
Heating: 830 - 830
2
)
Cooling: High 62 - 63
Heating: High 64 - 65
G ; 3-way valve 1/2”
L ; 2-way valve 1/4”
G (gas side) ; 1/2”
L (liquid side) ; 1/4”
rolling piston type
—
—
—
—
—
—
835 - 845
5
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
Unit CS-A12CTP CU-A12CTP5
Heat Exchanger Description Evaporator Condenser
Tube material Copper Copper
Fin material Aluminium Aluminium (Blue Coated)
Fin Type Louver Fin Corrugated Fin
Row / Stage (Plate fin configuration, forced draft)
2×12 2×24
FPI 20 16
Size (W × H × L) mm 857 × 252 × 25.4 720 × 504 × 36.38
Refrigerant Control Device — Capillary Tube
Refrigeration Oil (c.c) — SUNISO 4GSI (410)
Refrigerant (R-22) g (oz.) — 920 (32.5)
Thermostat Electronic Control —
Protection Device — Overload Protector
Capillary Tube Length mm — Cooling: 630, Heating: 455
Flow Rate l/min — Cooling: 6.5, Heating: 13.6
Inner Diameter mm — Cooling: 1.2, Heating: 1.5
Air Filter Material
Style
Capacity Control Capillary Tube
Compressor Capacitor µF, VAC — 30 µF, 370VAC
Fan Motor Capacitor µF, VAC 1.5 µF, 440VAC 2.0 µF, 450VAC
P.P.
Honeycomb
—
•
Specifications are subject to change without notice for further improvement.
6
Unit CS-A18CTP CU-A18CTP5
Power Source Phase
V
Cycle
Cooling Capacity kW
Btu/h
kcal/h
Heating Capacity kW
Btu/h
kcal/h
Moisture Removal l/h
Pint/h
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
Single
220 - 230
50
5.30 - 5.30
18,100 - 18,100
4,560 - 4,560
6.00 - 6.00
20,500 - 20,500
5,160 - 5,160
2.9
6.1
Airflow Method OUTLET
SIDE VIEW TOP VIEW
INTAKE
Air Volume Indoor Air (Lo) m3/min (cfm) Cooling: 8.5 (300) - 8.5 (300)
25.1 (890) - 26.7 (940)
Heating: 9.1 (320) - 9.1 (320)
Indoor Air (Me) m3/min (cfm) Cooling: 9.5 (340) - 9.5 (340)
—
Heating: 9.7 (340) - 9.7 (340)
Indoor Air (Hi) m3/min (cfm) Cooling: 10.2 (360) - 10.2 (360)
38.3 (1,350) - 40 (1,410)
Heating: 10.4 (370) - 10.4 (370)
Noise Level dB (A) Cooling: High 42 - 42; Low 37 - 37
Heating: High 42 - 42; Low 37 - 37
Power Noise Level dB (A) Cooling: High 55 - 55
Heating: High 55 - 55
Cooling: High 54 - 55
Heating: High 55 - 56
Cooling: High 67 - 68
Heating: High 68 - 69
Electrical Data Input Power W Cooling: 1,890 - 2,020
Heating: 1,890 - 2,020
Running Current A Cooling: 8.8 - 9.0
Heating: 8.8 - 9.0
EER W/W 2.80 - 2.62
COP W/W 3.17 - 2.97
Starting Current A 44
Piping Connection Port
(Flare piping)
Pipe Size
(Flare piping)
Drain
Hose
Power Cord Length
Number of core-wire
Inner diameter mm 20 —
Length m 0.6 —
inch
inch
inch
inch
G ; Half Union 1/2”
L ; Half Union 1/4”
G (gas side) ; 1/2”
L (liquid side) ; 1/4”
m 1.8
3 (1.5 mm
G ; 3-way valve 1/2”
L ; 3-way valve 1/4”
G (gas side) ; 1/2”
L (liquid side) ; 1/4”
2
)
—
—
Dimensions Height inch (mm) 21 - 9/32 (540) 26 - 31/32 (685)
Width inch (mm) 40 - 1/2 (1,028) 31 - 1/2 (800)
Depth inch (mm) 7 - 7/8 (200) 11 - 13/16 (300)
Net Weight lb (kg) 44 (20) 132 (60)
Compressor Type — Rotary (1 cylinder)
rolling piston type
Motor Type — Induction (2-poles)
Rated Output kW — 1.7
Air Circulation Type SIROCCO Propeller Fan
Material ABS STYLAC 181 AES + PC + GF15%
Motor Type Induction (4-poles) Induction (4-poles)
Input W 69.8 - 79.0 105 - 130
Rated Output W 29 67
Fan Speed Low rpm Cooling: 770 - 770
650 - 690
Heating: 810 - 810
Medium rpm Cooling: 870 - 870
—
Heating: 870 - 870
High rpm Cooling: 930 - 930
990 - 1,030
Heating: 930 - 930
7
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
Unit CS-A18CTP CU-A18CTP5
Heat Exchanger Description Evaporator Condenser
Tube material Copper Copper
Fin material Aluminium Aluminium (Blue Coated)
Fin Type Louver Fin Corrugated Fin
Row / Stage (Plate fin configuration, forced draft)
2 × 12
+
1 × 10
FPI 20 16
Size (W × H × L) mm 857 × 252 × 25.4
Refrigerant Control Device — Capillary Tube
Refrigeration Oil (c.c) — SUNISO 4GDID or ATMOS
Refrigerant (R-22) kg (oz.) — 1.55 (54.7)
Thermostat Electronic Control Mecha. Control
Protection Device — Inner Protector
Capillary Tube Length mm — 680
Flow Rate l/min — 11.5
Inner Diameter mm — 1.5
Air Filter Material
Style
Capacity Control Capillary Tube
Compressor Capacitor µF, VAC — 50 µF, 370VAC
Fan Motor Capacitor µF, VAC 1.5 µF, 440VAC 3.0 µF, 450VAC
+
857 × 210 × 12.7
P.P.
Honeycomb
769.2
732.9
M60 (700)
2 × 26
× 660.4 × 44
—
•
Specifications are subject to change without notice for further improvement.
8
Unit CS-A24CTP CU-A24CTP5
Power Source Phase
V
Cycle
Cooling Capacity kW
Btu/h
kcal/h
Heating Capacity kW
Btu/h
kcal/h
Moisture Removal l/h
Pint/h
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
Single
220 - 230
50
6.40 - 6.40
21,800 - 21,800
5,500 - 5,500
7.50 - 7.50
25,600 - 25,600
6,450 - 6,450
3.5
7.4
Airflow Method OUTLET
SIDE VIEW TOP VIEW
INTAKE
Air Volume Indoor Air (Lo) m3/min (cfm) Cooling: 10.5 (370) - 10.5 (370)
25.6 (910) - 27.4 (970)
Heating: 11.0 (390) - 11.0 (390)
Indoor Air (Me) m3/min (cfm) Cooling: 11.8 (420) - 11.8 (420)
—
Heating: 11.8 (420) - 11.8 (420)
Indoor Air (Hi) m3/min (cfm) Cooling: 12.9 (460) - 12.9 (460)
46.0 (1,620) - 47.2 (1,670)
Heating: 12.9 (460) - 12.9 (460)
Noise Level dB (A) Cooling: High 47 - 47; Low 42 - 42
Heating: High 47 - 47; Low 42 - 42
Power Noise Level dB (A) Cooling: High 60 - 60
Heating: High 60 - 60
Cooling: High 59 - 60
Heating: High 60 - 61
Cooling: High 72 - 73
Heating: High 73 - 74
Electrical Data Input Power W Cooling: 2,600 - 2,740
Heating: 2,720 - 2,860
Running Current A Cooling: 12.7 - 13.0
Heating: 13.3 - 13.6
EER W/W 2.46 - 2.34
COP W/W 2.76 - 2.62
Starting Current A 66
Piping Connection Port
(Flare piping)
Pipe Size
(Flare piping)
Drain
Hose
Power Cord Length
Number of core-wire
Inner diameter mm 20 —
Length m 0.6 —
inch
inch
inch
inch
G ; Half Union 5/8”
L ; Half Union 1/4”
G (gas side) ; 5/8”
L (liquid side) ; 1/4”
m 1.8
3 (2.5 mm
G ; 3-way valve 5/8”
L ; 3-way valve 1/4”
G (gas side) ; 5/8”
L (liquid side) ; 1/4”
2
)
—
—
Dimensions Height inch (mm) 21 - 9/32 (540) 26 - 31/32 (685)
Width inch (mm) 40 - 1/2 (1,028) 31 - 1/2 (800)
Depth inch (mm) 7 - 7/8 (200) 11 - 13/16 (300)
Net Weight lb (kg) 44 (20) 139 (63)
Compressor Type — Rotary (1 cylinder)
rolling piston type
Motor Type — Induction (2-poles)
Rated Output kW — 2.2
Air Circulation Type SIROCCO Propeller Fan
Material ABS STYLAC 181 AES + PC + GF15%
Motor Type Induction (4-poles) Induction (4-poles)
Input W 94.2 - 104.1 190.0 - 171.3
Rated Output W 51 108
Fan Speed Low rpm Cooling: 900 - 900
635 - 680
Heating: 940 - 940
Medium rpm Cooling: 1,010 - 1,010
—
Heating: 1,010 - 1,010
High rpm Cooling: 1,100 - 1,100
1,140 - 1,170
Heating: 1,100 - 1,100
9
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
Unit CS-A24CTP CU-A24CTP5
Heat Exchanger Description Evaporator Condenser
Tube material Copper Copper
Fin material Aluminium Aluminium (Blue Coated)
Fin Type Louver Fin Corrugated Fin
Row / Stage (Plate fin configuration, forced draft)
2 × 12
+
1 × 10
FPI 20 16
Size (W × H × L) mm 857 × 252 × 25.4
Refrigerant Control Device — Capillary Tube
Refrigeration Oil (c.c) — SUNISO 4GDID or ATMOS
Refrigerant (R-22) kg (oz.) — 2.23 (78.7)
Thermostat Electronic Control Mecha. Control
Protection Device — Inner Protector
Capillary Tube Length mm — 690
Flow Rate l/min — 20.0
Inner Diameter mm — 1.9
Air Filter Material
Style
Capacity Control Capillary Tube
Compressor Capacitor µF, VAC — 50 µF, 370VAC
Fan Motor Capacitor µF, VAC 3.0 µF, 440VAC 3.0 µF, 450VAC
+
857 × 210 × 12.7
P.P.
Honeycomb
2 × 26
769.2
× 660.4 × 44
732.9
M60 (1,130)
—
•
Specifications are subject to change without notice for further improvement.
10
3 Dimensions
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
11
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
12
4 Refrigeration Cycle Diagram
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
13
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
14
5 Block Diagram
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
15
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
16
6 Wiring Diagram
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
17
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
18
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
7 Operation Details
7.1. Cooling Mode Operation
Cooling in operation according to Remote Control setting.
Time Delay Safety Control (3 minutes)
When the compressor is stopped by Remote Control, it restarts after 3 minutes when it is turned ON by Remote Control.
•
When the setting temperature is reached during cooling operation, the compressor stops and it will not start for 3 minutes.
•
7 minutes Time Save Control
The compressor will start automatically if it has stopped for 7 minutes even if the room temperature is between the compressor
•
ON temperature and OFF temperature.
Anti-Freezing Control
If the temperature of the indoor heat exchanger falls
•
continuously below 2°C for 4 minutes or more, the
compressor turns off to protect the indoor heat exchanger
from freezing. The fan speed setting remains the same.
Compressor will restart again when the indoor heat
•
exchanger temperature rises to 10°C (Recovery).
3 minutes waiting of Time Delay Safety Control is valid for
Cooling Operation.
Compressor Reverse Rotation Protection Control
If the compressor is operating continuously for 5 minutes or longer and the temperature difference between intake air and
•
indoor heat exchanger is 2.5°C or less for 2 minutes, compressor will stop and restart automatically.
(Time Delay Safety Control is valid)
▲
T = Intake air temperature - Indoor heat exchanger temperature
This is to protect reverse rotation of the compressor when there is a instantaneous power failure.
Anti-Dew Formation Control
Purpose is to prevent dew formation on indoor unit air discharge area.
•
When the following conditions occur for 30 minutes continuously, anti-dew formation is controlled by indoor fan speed shift to
•
low (Changed to HLo):
Indoor intake air temperature is more than 24°C and less than 30°C.
−
Remote Control setting temperature is less than 25°C.
−
Compressor is on.
−
Cooling operation mode.
−
Indoor Fan motor operate at Low fan speed.
−
This control is cancelled immediately when above condition is changed.
•
19
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
Compressor Protection Control
After the compressor starts for 50 seconds but the outdoor fan motor is still OFF, the compressor will stop and restart
•
automatically. (Time Delay Safety Control is valid).
If the above phenomenon is repeated for 3 times, the compressor will stop totally.
•
The above phenomenon is reset when there is a change to heating mode or stopped by Remote Control Switch.
•
Automatic Fan Speed Mode
When Automatic Fan Speed is selected at Remote Control during cooling operation.
Fan speed rotates in the range of Hi to Me.
•
20
Cooling Operation Time Diagram
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU- A24CTP5
21
CS-A12CTP CU-A12CTP5 / CS-A18CTP CU-A18CTP5 / CS-A24CTP CU-A24CTP5
7.2. Soft Dry Mode Operation
The unit starts cooling operation until the room temperature reaches the setting temperature set on the Remote Control, and
•
then Soft Dry operation will start.
During Soft Dry operation, the Indoor Fan will operate at Lo- speed.
•
The operation will be switched on and off for up to 10 minutes “ON” and 6 minutes “OFF”. Once Soft Dry operation is turned
•
off, it stops for 6 minutes.
Time Delay Safety Control
Once the compressor stops, it will not start for 3 minutes during Cooling operation.
•
Anti-Freezing Control
Same as Anti-Freezing Control for Cooling Mode operation. (For Soft Dry region, 6 minutes waiting is valid during compressor
•
stops.)
Compressor Reverse Rotation Protection Control
Same as Compressor Reverse Rotation Protection Control for Cooling Mode Operation. (For Soft Dry region, 6 minutes waiting
•
is valid during compressor stops.)
Compressor Protection Control
Same as Compressor Protection Control for Cooling Mode Operation.
•
Anti-Dew Formation Control
Same as Anti-Dew Formation Control for Cooling Mode operation.
•
Automatic Fan Speed Mode
When Automatic Fan Speed is selected at Remote Control during Soft Dry operation.
Fan speed rotates at Lo- speed.
•
22
Loading...