Panasonic CQ-C3305N Operating Instructions

WMA MP3 CD Player/Receiver

• Please read these instructions carefully before using this product and keep this manual for future reference.

• Bitte lesen Sie diese Bedienungsanleitung vor der Verwendung dieses Produktes aufmerksam durch und bewahren Sie sie danach für spätere Nachschlagzwecke sorgfältig auf.

• Prière de lire ces instructions attentivement avant d’utiliser le produit et garder ce manuel pour l’utilisation ultérieure.

• Leest u deze instructie alstublieft zorgvuldig door voor u dit product in gebruik neemt en bewaar deze handleiding voor later gebruik.

• Läs igenom denna bruksanvisning noga innan produkten tas i bruk. Spara bruksanvisningen för framtida behov.

•

Si prega di leggere attentamente queste istruzioni prima di usare questo prodotto e di conservare questo manuale per usi futuri.

•

Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.

•

Læs venligst denne brugsvejledning grundigt, inden dette produkt tages i brug og gem den til senere konsultation.

•

Przeczytaj uważnie instrukcję obsługi przed rozpoczęciem używania urządzenia i zachowaj ją do użytku w przyszłości.

• Před použitím přístroje si pozorně přečtěte tento návod a uschovejte si ho pro budoucí potřebu.

• Mielött használja a terméket kérjük, hogy gondosan olvassan el ezeket az előírásokat és a későbbiekben felmerülő kérdések miatt kérjük tartsa meg a használati utasítást.

Operating InstructionsOperating Instructions

BedienungsanleitungBedienungsanleitung

Manuel d’instructionsManuel d’instructions

GebruiksaanwijzingGebruiksaanwijzing

BruksanvisningBruksanvisning

Manuale di istruzioniManuale di istruzioni

Manual de InstruccionesManual de Instrucciones

BrugsvejledningBrugsvejledning

Instrukcja obsługiInstrukcja obsługi

Návod k obsluzeNávod k obsluze

Használati utasításokHasználati utasítások

Model: CQ-C3305N

CQ-C3305N

English

Safety Information

 Read the operating instructions for the unit and all other

components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual.

 This manual uses pictographs to show you how to use the

product safely and to alert you to potential dangers resulting from improper connections and operations. The meanings of the pictographs are explained below. It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly.

Warning

This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in severe injury or death.

Caution

This pictograph intends to alert you to the presence of important operating instructions and installation instructions. Failure to heed the instructions may result in injury or material damage.

Warning

Observe the following warnings when using this unit.

 The driver should neither watch the display nor

operate the system while driving.

Watching the display or operating the system will distract the driver from looking ahead of the vehicle and can cause accidents. Always stop the vehicle in a safe location and use the parking brake before watching the display or operating the system.

 Use the proper power supply.

This product is designed for operation with a negative grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system.

 Protect the Deck Mechanism.

Do not insert any foreign objects into the slot of this unit.

 Do not disassemble or modify the unit.

Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic Service Centre.

 Do not use the unit when it is out of order.

If the unit is out of order (no power, no sound) or in an abnormal state (has foreign objects in it, is exposed to water, is smoking, or smells), turn it off immediately and consult your dealer.

 The remote control unit should not lie about in the

car.

If the remote control unit lies about, it could fall on the ﬂ oor while driving, get wedged under the brake pedal, and lead to a trafﬁ c accident.

 Refer fuse replacement to qualiﬁ ed service

personnel.

When the fuse blows out, eliminate the cause and have it replaced with the fuse prescribed for this unit by a qualiﬁ ed service engineer. Incorrect replacement of the fuse may lead to smoke, ﬁ re, and damage to the product.

Observe the following warnings when installing.

 Disconnect the lead from the negative (–) battery

terminal before installation.

Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to a short circuit. Some cars equipped with the electrical safety system have speciﬁ c procedures of battery terminal disconnection.

FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.

 Never use safety-related components for

installation, grounding, and other such functions.

Do not use safety-related vehicle components (fuel tank, brake, suspension, steering wheel, pedals, airbag, etc.) for wiring or ﬁ xing the product or its accessories.

 Installing the product on the air bag cover or in a

location where it interferes with airbag operation is prohibited.

 Check for piping, gasoline tank, electric wiring, and

other items before installing the product.

If you need to open a hole in the vehicle chassis to attach or wire the product, ﬁ rst check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole from outside if possible.

 Never install the product in a location where it

interferes with your ﬁ eld of vision.

 Never have the power cord branched to supply

other equipment with power.

 After installation and wiring, you should check the

normal operation of other electrical equipment.

The continuation of their using in abnormal conditions may cause ﬁ re, electrical shock or a trafﬁ c accident.

 In the case of installation to an airbag-equipping

car, conﬁ rm warnings and cautions of the vehicle manufacturer before installation.

 Make sure the leads do not interfere with driving or

getting in and out of the vehicle.

 Insulate all exposed wires to prevent short

circuiting.

Caution

Observe the following cautions when using this unit.

 Keep the sound volume at an appropriate level.

Keep the volume level low enough to be aware of road and trafﬁ c conditions while driving.



This unit is designed for use exclusively in automobiles.

 Do not operate the unit for a prolonged period with

the engine turned off.

Operating the audio system for a long period of time with the engine turned off will drain the battery.

 Do not expose the unit to direct sunlight or

excessive heat.

Otherwise these will raise the interior temperature of the unit, and it may lead to smoke, ﬁ re, or other damage to the unit.

 Do not use the product where it is exposed to water,

moisture, or dust.

Exposure of the unit to water, moisture, or dust may lead to smoke, ﬁ re, or other damage to the unit. Make especially sure that the unit does not get wet in car washes or on rainy days.

 Set the volume level to low enough before the AUX

connection is completed.

Failure to observe this, the loud noise may come out and damage your speakers and your hearing. Direct connection of the speaker/headphone output of an external device without any attenuator may distort sound or damage the connected external device.

Observe the following cautions when installing.



Refer wiring and installation to qualiﬁ ed service personnel.

Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer. Panasonic is not liable for any problems resulting from your own installation of the unit.



Follow the instructions to install and wire the product.

Not following the instructions to properly install and wire the product could cause an accident or ﬁ re.

 Take care not to damage the leads.

When wiring, take care not to damage the leads. Prevent them from getting caught in the vehicle chassis, screws, and moving parts such as seat rails. Do not scratch, pull, bend or twist the leads. Do not run them near heat sources or place heavy objects on them. If leads must be run over sharp metal edges, protect the leads by winding them with vinyl tape or similar protection.

 Use the designated parts and tools for installation.

Use the supplied or designated parts and appropriate tools to install the product. The use of parts other than those supplied or designated may result in internal damage to the unit. Faulty installation may lead to an accident, a malfunction or ﬁ re.



Do not block the air vent or the cooling plate of the

unit.

Blocking these parts will cause the interior of the unit to overheat and will result in ﬁ re or other damage.

 Do not install the product where it is exposed to

strong vibrations or is unstable.

Avoid slanted or strongly curved surfaces for installation. If the installation is not stable, the unit may fall down while driving and this can lead to an accident or injury.

 Installation Angle

The product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30˚. The user should bear in mind that in some areas there may be restrictions on how and where this unit must be installed. Consult your dealer for further details.

 Wear gloves for safety. Make sure that wiring is

completed before installation.



To prevent damage to the unit, do not connect the

power connector until the whole wiring is completed.

 Do not connect more than one speaker to one set of

speaker leads. (except for connecting to a tweeter)

Safety Information

CQ-C3305N

English

Panasonic welcomes you to our constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.

The instruction manual consists of 2 books. One is “Operating Instructions” describing the operations of the main unit. The other is “System Upgrade Guidebook” describing the optional devices such as CD changer.

Safety Information, Before Reading These Instructions

Operating Instructions

(YEFM285930)

System Upgrade Guidebook

(YEFM262785)

Installation Instructions

(YEFM294302) (YEFM294303) (YEFM294304)

PAN EUROPEAN GUARANTEE (Warranty Card)

Power Connector

Instruction kit

Q’ty: 1 set

(YEAJ02874)

Q’ty: 1

Before Reading These Instructions

Accessories

Lock Cancel Plate

Mounting Bolt

(5 mm )

ISO Antenna Adapter

Mounting Collar

Trim Plate Removable

Face Plate Case

(YEP0FZ5699)

Q’ty: 1 set

(YEFX0217263A)

Q’ty: 1

(YEFC051011)

Q’ty: 1

(YEFA131839A)

Q’ty: 1

Notes:

• The number in parenthesis underneath each accessory part name is the part number for maintenance and service.

• Accessories and their parts numbers are subject to modiﬁ cation without prior notice due to improvements.

• Mounting Collar and Trim Plate are mounted on the main unit at shipment.

Safety Information

CLASS 1 LASER PRODUCT

Caution Label

Deck Ass’y (in the unit, upper side)

Label Indications and Their Locations

CAUTION

LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

Laser Product

Caution

This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those speciﬁ ed herein may result in hazardous radiation exposure.

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

Do not take apart this unit or attempt to make any changes yourself.

This unit is a very intricate device that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disassemble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

OO-OOOOO

XXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXX

XXXXXXXXXXXXXXXX

XXXXXXXXXXXXXXX

XXXXXXXXXXXXXXXXX

XXXXXXXXXXXXXX

XXXXXXXXXXXXXXXX

OO-OOOOO OO-OOOOO OO-OOOOO

CQ-C3305N

English

Deutsch 34 Français 66 Nederlands 98 Svenska 130 Italiano 162 Español 194 Dansk 226

Polski 258 Češky 290 Magyar 322

Contents

• Safety Information 2

• Before Reading These Instructions 5

• Features 6

• Controls Layout 8

• Preparation (ACC Setting etc.) 9

• General 10

• Radio 12

• Radio Data System (RDS) in FM Broadcasting 14

• CD Player 18

• MP3/WMA Player 20

• Audio Setting 24

• Function Setting 26

• Troubleshooting 28

• Error Display Messages 31

• Notes on Discs 32

• Maintenance/Fuse 32

• Speciﬁ cations 33

CommonEach SourceAs Needed

Features

Hands-Free Phone System

Connection of the optional Hands-Free Phone System (HandsFree Kit featuring Bluetooth

technology: CY-BT100N) allows users to talk on a handsfree cellular phone if the phone supports Bluetooth.

Note: This unit is designed only for receiving calls. It cannot send calls.

Bluetooth

The Bluetooth word mark and logo are owned by the Bluetooth SIG, Inc. and any use of such marks by Matsushita Electric Industrial Co., Ltd. is under license. Other trademarks and trade name are those of their respective owners.

Expansion Module (Hub Unit)

Connection of the Expansion Module (hub unit, CY-EM100N) allows users to connect up to 4 optional devices shown below.

Wide Array of Components for System Upgrade

Various optional components allow users to obtain availability of wide range of system upgrade. Upgrading the system delivers relaxed AV space in a car. For further information, refer to the separate System Upgrade Guidebook.

• CD Changer

The optional adapter (Conversion Cable for DVD/CD Changer: CA-CC30N) allows you to connect the optional Panasonic CD changer unit (CX-DP880N).

• iPod

The optional adapter (Direct Cable for iPod: CA-DC300N) allows you to connect the optional iPod series. iPod is a trademark of Apple Computer, Inc., registered in the U.S.A. and other countries.

• Hands-Free Phone System

SQ (Sound Quality)

SQ is a function that can call up various sound types at the touch of button in accordance with your listening music type.

AUX (AUX1) Input Terminal

The AUX input terminal is equipped on the front panel. Your mobile audio player and other devices are connectable to this unit without any difﬁ culty.

CQ-C3305N

English

Controls Layout

Note: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)

Main Unit

VOL Volume (

 page 11)

PUSH SEL Select (

 page 24, 26)

LIST (

 P16 of System Upgrade Guidebook)

DISC (

 P12 of System Upgrade Guidebook)

FOLDER (

 page 20)

MUTE (

 page 11)

SQ Sound Quality (

 page 25)

Remote control sensor

TA Trafﬁ c Announcement ( page 16) AF Alternative Frequency (

 page 15)

SOURCE (

 page 11)

PWR Power (

 page 10)

TUNE (

 page 12)

TRACK (FILE) (

 page 18, 20)

BAND (

 page 12)

Play/Pause (

 page 18, 20)

APM Auto Preset Memory (

 page 13)

OPEN (

 page 18, 20)DISP Display ( page 10)

PTY Programme Type

(

 page 17)

Remote Control Unit (Option)

Controls Layout, Preparation

AUX1 ( page 11)1 to 6 ( page 12)

3 (SCROLL) (

 page 19, 21)

4 (RANDOM) (

 page 19, 21)

5 (SCAN) (

 page 19, 21)

6 (REPEAT) (

 page 19, 21)

Notes:

• Remote Control Unit for CQ-C3305N is option (CA-RC80N).

• The optional remote control is available from your local dealer. (CA-RC80N)

Power Mode (Source)

Tune Track selection Fast forward/fast reverse

(CA-RC80N)

Mute/attenuation

Volume

Band Pause

Preparation

The demonstration message appears for initial use.

Set your car’s ignition switch to the

ACC or ON position.

Press [PWR] (Power).

The demonstration screen appears.

Hold down [VOL] (PUSH SEL: Select)

for 2 sec. or more to open the menu.

Press [VOL] (PUSH SEL: Select) to

select the Demonstration setting.

(“DEMO” is displayed.)

Tu r n [VOL] counterclockwise.

Notes:

• To return to the regular mode, press [DISP].

• Refer to the section on “Function Setting” (

 page

26).

• When “NO DISC” is displayed, the Demonstration cannot be cancelled.

Cancellation of DemonstrationACC Setting

The 24-hour system is used for the clock.

Press [PWR] (Power).

Select the radio AM (LW/MW) mode.

(page 12)

Hold down [DISP] for 2 sec. or more.

Adjust the hour and press [DISP].

[]: Forward []: Backward

Adjust the minute and press [DISP] to

conﬁ rm the adjustment.

[]: Forward []: Backward

Notes:

• Adjust the clock when “NO CT” appears on the display.

• Hold down [] or [] to change numbers rapidly.

• When a broadcast of FM Radio Data System is received, the clock is adjusted automatically by the Clock Time service. (

 page 14)

Clock Adjustment

Caution

• Be sure to select OFF when your car has no ACC position in the ignition switch. Failure to do this could cause the battery to go dead.

For an ACC-equipped car, select ON. (

 page 27) The

following functions are available. (Default: off)

• The power is turned on automatically when inserting a disc.

• The clock can be displayed even if the power is off. (



page 10)

: ACC not equipped (Default)

: ACC equipped

OFF

ACC

IGN

CQ-C3305N

English

General

This chapter explains how to turn on or off the power, how to adjust the volume, etc.

Power on

Press [PWR] (Power).

Power off

Hold down [PWR] (Power) for 1 sec. or more.

You can remove the face plate to prevent it from being stolen.

Removing

Turn off the power. ( above)

Press [OPEN]. The face plate will be opened.

Push the face plate to the left.

Pull it out toward you.

Put the face plate in

the case.

Cautions

• This face plate is not waterproof. Do not expose it to water or excessive moisture.

• Do not remove the face plate while driving your car.

• Do not place the face plate on the dashboard or nearby areas where the temperature rises to high.

• Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts.

• If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth.

• To avoid damaging the face plate, do not push it down or place objects on it while it is open.

Power On/off

(PWR: Power)

Face Plate Removing/Mounting

(Anti-Theft System)

Display Change

(DISP: Display)

The display changes as follows every time [DISP] is pressed. (ACC ON)

At power-off:

Clock display (Default)

Display off

Mounting

Fit the face plate with its left hole on the left pin provided on the main unit.

Fit the other hole on the other pin applying slight pressure.

At power-on:

When the power is set to ON, refer to the description for each source mode.

Volume off (down)

Press [MUTE].

Cancel

Press [MUTE] again.

Note: You can select mute or attenuation. ( page 27)

 Up  Down

Setting Range: 0 to 40 Default: 18

Note: The volume level can be set independently for each source. (For radio, one volume setting for AM (LW/MW), one volume setting for all FMs)

Volume Adjustment

(VOLUME)

Temporary Volume Off

(Down)

MUTE (ATT: Attenuation)

Caution

• Set the volume level to low enough before the AUX connection is completed.

Failure to observe this, the loud noise may come

out and damage your speakers and your hearing.

The source changes as follows every time [SOURCE] is pressed.

AUX1 (AUX1 in) (3.5 mm  stereo) From line output of external sound/audio device (ex. Silicon-audio player, HDD player, etc.)

Radio

FM1, FM2, FM3, AM ( page 12)

Player

When loading CD ( page 18)

When loading MP3/WMA disc ( page 20)

AUX1

Device connected to the AUX1 terminal of this unit

When an optional device is connected:

Shift to connected device

When connecting CD changer

When connecting iPod

When an expansion module is connected:

The devices connected to the ports 1 to 4 are activated in sequence after shifting to AUX2 (device connected to the AUX terminal of the expansion module).

Note: For information about connectable devices, refer to the System Upgrade Guidebook or the instruction manual for each device.

System-up Connector

Source Selection

(SOURCE)

CQ-C3305N

English

Press [SOURCE] to select the radio

mode.

Press [BAND] to select a band.

Select a station.

Frequency Adjustment

[] (TUNE): Higher [] (TUNE): Lower Note: Hold down for 0.5 sec. or more and release

for station search.

Preset Station Selection

Press the numeric button [1] to [6].

Notes:

• For tuning in on only stations whose receiving conditions are good in the seeking mode, set LOCAL to ON. (

 page 26)

• For reducing noise when a receiving FM stereo wave is weak, set FM MONO to ON. (

 page 26)

Radio

This chapter explains how to listen to the radio.

Band Preset NumberFrequency

Lights while receiving an FM stereo signal.

Operation FlowRadio Mode Display

Radio

Up to 6 stations can be preset in AM, FM1, FM2, and FM3 respectively.

Auto Preset Memory (APM)

Stations with good receiving conditions automatically preset.

Select a band.

Hold down [BAND] (APM) for 2 sec. or

more.

The preset stations under best receiving conditions are received for 5 sec. each after presetting the stations (SCAN). To stop scanning, press the numeric button [1] to [6].

Notes:

• New stations overwrite existing saved stations.

• Only RDS stations will be saved at default setting (AF ON). To select non-RDS stations, set AF to OFF. (

 page 15)

Manual Station Preset

Tune in to a station.

Hold down the numeric button [1] to [6]

for 2 sec. or more.

Station Preset

(APM: Auto Preset Memory)

Display Change

(DISP: Display)

Press [DISP].

Frequency

Clock time (CT)*

Display off

* Adjust the clock when “NO CT” appears on the screen. (Clock Adjustment

 page 9)

AM (LW/MW)

Frequency

PS (Programme Service Name)

Clock time (CT)*

Display off

FM (Non RDS)

Lights while LOCAL is activated. (

 page 26)

Lights while MONO is activated. (

 page 26)

CQ-C3305N

English

Radio Data System (RDS) in FM Broadcasting

Useful functions such asAF, TA, PTY are available in the RDS (Radio Data System)-ready areas.

What is RDS?

Radio Data System (RDS) in FM Broadcasting

Alternative Frequency (AF) RDS Mode Display

Some FM stations are broadcasting added data compatible with RDS. This radio set offers convenient functions using such data. RDS service availability varies with areas. Please understand if RDS service is not available in your area, the following service is not available, either. The following functions are available when receiving RDS stations.

AF (Alternative Frequency)

PTY (Programme Type)

Alternative Frequency (AF) Mode

Hold down [TA] (AF) for 2 sec. or more to select one of the following AF modes.

AF ON:

AF, Best Station Research and PI seek function are active.

AF OFF:

When the AF network of an RDS station is not required.

Preset Memory (AF ON Setting)

Preset Station Calling (Best Station Research)

AF self-tuning allows you to select a station with good reception from the same network when the preset tuning is activated.

For Poor Reception (PI Seek)

If reception becomes poor when tuning in a preset station, press the same preset number button. The same station with better reception will be searched for. Press the same preset number button again to cancel.

Note: For PI Seek, cancel the TA mode ﬁ rst, then execute PI Seek.

Low level AF operating sensitivity. (Default)

High level AF operating sensitivity.

When the AF network of an RDS station is not required.

Display Change

The following functions are available when the AF mode is active (

 page 15).

• When receiving conditions become bad, a station with

better receiving conditions is automatically tuned in to.

• When executing APM, only RDS stations are selected.

• When calling up a preset station, a best receiving

station is selected automatically. (BSR Best Stations Research)

Notes:

• The AF sensitivity can be adjusted. ( page 15)

• The AF available range can be adjusted. ( page 26)

TA (Trafﬁ c Announcement)

The following functions are available when the TA mode is active. (

 page 16)

• A TP (Trafﬁ c programme)

station is automatically searched for and received at the instant of toggling the TA mode on if you are receiving a non-TP station.

• When executing station search or APM, only TP

stations are selected.

• Setting to TA on with the unit in another mode, it will

automatically switch to radio mode and output the trafﬁ c announcement when the trafﬁ c announcement begins. The trafﬁ c announcement having ﬁ nished, the unit will return to the previous mode. (TA Standby Mode)

The following functions are available when the PTY mode is active. (

 page 17)

• The PTY of receiving station appears.

• Programs can be searched for by PTY.

Note: PTY language can be selected. (

 page 26)

Other Functions of RDS

CT (Clock Time)

The clock is automatically adjusted.

PS (Programme Service Name)

As well as the frequency, the name of the broadcast station appears.

EON (Enhanced Other Network)

RDS information is updated constantly in response to the current position.

EON-TA

Trafﬁ c information from the current and other network stations can be received.

Emergency Announcement Reception

Emergency announcement automatically appears on the display when it is received.

Press [DISP].

PS (Programme Service Name) (Default)

Frequency

Clock time

Display off

Programme service name

Lights when AF is activated.

Lights when TA is activated.

Lights when PTY is activated.

CQ-C3305N

English

Radio Data System (RDS) in FM Broadcasting

(TA: TRAFFIC ANNOUNCEMENT)

Other RDS Functions

Radio Data System (RDS) in FM Broadcasting

PTY

(PTY: PROGRAMME TYPE)

TA On/Off

Pressing [TA] toggles TA on and off. (Default: OFF)

The following functions are available when the TA mode is active.

• A TP station is automatically searched for and received

at the instant of toggling the TA mode on if you are receiving a non-TP station or a TP station with poor reception.

• When executing seek tuning or APM, only TP stations

are selected. (

 page 13 for “Auto Preset Memory

(APM)”)

• Seeking TA on with the unit in another mode, it

will automatically switch to the radio mode and a trafﬁ c announcement is broadcast on the radio when the trafﬁ c announcement begins. The trafﬁ c announcement having ﬁ nished, the unit return to the previous mode. (TA standby mode)

Trafﬁ c Information Only (TA Mute)

While listening to an FM station which is not currently broadcasting trafﬁ c announcement, turn the [VOL] to the counterclockwise to set the volume to 0. The trafﬁ c announcement will be output at the TA volume level.

PTY On/Off

Holding down [DISP] (PTY) for 2 sec. or more toggles PTY mode on and off.

Programme Search by PTY

Programs can be searched for by use of PTY that has been originally preset.

Press the numeric button [1] to [6] to select PTY in the PTY mode.

Programme

Type

Contents

1 NEWS

NEWS

2 SPEECH

AFFAIRS, INFO, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

3 SPORT

SPORT

4 POP M

POP M

5 CLASSICS

CLASSICS

6 MUSIC

ROCK M, EASY M, LIGHT M, OTHER M, JAZZ, COUNTRY, NATION M, OLDIES, FOLK M

Another station in the same PTY is searched for by pressing [BAND].

Notes:

• When there is no corresponding programme type

station, “NONE” is displayed.

• A desired PTY appears for 5 seconds.

• Preset contents are changeable.

Press [BAND].

Search starts.

Notes:

• To stop searching, press [BAND].

• When there is no corresponding programme type station, “NONE” is displayed.

PTY Preset Change

Original PTY presets can be changed as you like.

Select a PTY that you would like to

preset.

Follow the procedure of ordinary

presetting. ( page 13)

PTY Language Selection

The language displayed on the display is selectable. (English or Swedish) (

 page 26)

Detailed PTY Selection

Press [] or [] to select PTY.

Enhanced Other Networks (EON)

When EON data is received, the EON indicator lights and the TA and AF functions are expanded as follows.

TA:

Trafﬁ c information from the current and other network stations can be received.

AF:

The frequency list of preset RDS stations is updated by EON data. EON enables the radio to make fuller use of RDS information. It constantly updates the AF list of preset stations, including the one that is currently tuned in to. For example, if you preset a station far from home, you will later be able to receive the same station at an alternative frequency, or another station serving the same programme. EON also keeps track of locally available TP stations for quick reception.

Emergency Announcement Reception

When an emergency announcement is broadcast, the unit is automatically switched to receiving that broadcast (even when in the CD mode, MP3 mode or AUX mode). During receiving the emergency announcement, “ALARM” appears on the display.

Note: Emergency announcements are broadcast at the TA volume level. (

 Above)

SPEECH  MUSIC  NEWS  AFFAIRS  INFO  SPORT  EDUCATE  DRAMA  CULTURE  SCIENCE  VARIED  POP M  ROCK M  EASY M  LIGHT M  CLASSICS  OTHER M  WEATHER FINANCE  CHILDREN  SOCIAL  RELIGION  PHONE IN  TRAVEL  LEISURE  JAZZ  COUNTRY  NATION M  OLDIES  FOLK M  DOCUMENT

CQ-C3305N

English

Random Play

All the available tracks are played in a random sequence.

Press [4] (RANDOM). lights. Press again to cancel.

Scan Play

The ﬁ rst 10 seconds of each track is played in sequence.

Press [5] (SCAN). Press again to cancel.

Repeat Play

The current track is repeated.

Press [6] (REPEAT). lights. Press again to cancel.

Cautions

• This unit does not support 8 cm discs.

• Do not insert a disc when

indicator lights

because a disc is already loaded.

• Do not use irregularly shaped discs. (

 page 32)

• Do not use discs that have a seal or label attached.

• To avoid damaging the face plate, do not push it down or place objects on it while it is open.

• Do not pinch your ﬁ nger or hand in the face plate.

• Do not insert foreign matter into the disc slots.

• Refer to the section on “Notes on CD/CD Media (CD-ROM, CD-R, CD-RW)” (

 page 32).

• A disc which has both CD-DA data and MP3/WMA data on it may not be reproduced normally.

Random, Scan, Repeat Play

(RANDOM, SCAN, REPEAT)

CD Player

When a disc is already loaded, press [SOURCE] to select the CD mode.

Press [OPEN] to open the face plate.

Load a disc with the printed side facing up.

Note: It may take some time to start playing.

Operation Flow

Track number Time

Play Mode indicators

Lights when each mode is activated.

Random play Repeat play

Lights when the disc is loaded.

CD Mode Display

Select a desired portion.

Track Selection

[] (TRACK): Next track [] (TRACK): Preceding track (press twice) Note: Hold down for fast forward/reverse.

Pause

Press []. Press again to cancel.

Display Change

(DISP: Display)

Press [DISP].

Track/play time

Disc title

Track title

Clock time

Display off

Close the face plate manually.

Notes:

• The unit recognizes the disc and starts playing automatically.

• The power will be turned on automatically when a disc is loaded.

Disc Eject



Press [OPEN].



Press [] and take the disc out.



Close the face plate manually.

Notes:

• To have another circle scroll while a title is displayed, press [3] (SCROLL). If the number of displayed characters is 8 or less, the characters do not scroll.

• “NO TEXT” is displayed when there is no information on the disc.

[] (Eject)

Printed side

CQ-C3305N

English

Random, Scan, Repeat Play

(RANDOM, SCAN, REPEAT)

MP3/WMA Player

Select a desired portion.

Folder Selection

[] (FOLDER): Next folder [] (FOLDER): Preceding folder

File Selection

[] (TRACK): Next ﬁ le [] (TRACK): Preceding ﬁ le (press twice) Note: Hold down for fast forward/reverse.

Pause

Press []. Press again to cancel.

Operation FlowMP3/WMA Mode

Display

Folder number

File number

Notes:

• To have another circle scroll while a text is displayed, press [3] (SCROLL). If the number of displayed characters is 8 or less, the characters do not scroll.

• “NO TEXT” is displayed when there is no information on the disc.

• ID3/WMA tag information is displayed for the album name and title/artist name.

Play Mode indicators

Lights when each mode is activated.

Random play Repeat play Folder Random, Folder Repeat, Folder Scan

Lights when the disc is loaded.

Random Play

All the available ﬁ les are played in a random sequence.

Press [4] (RANDOM). lights. Press again to cancel.

Folder Random Play

All the ﬁ les in the current folder are played in a random sequence.

Hold down [4] (RANDOM) for 2 sec. or more. lights. Hold down again to cancel.

Scan Play

The ﬁ rst 10 seconds of each ﬁ le is played in sequence.

Press [5] (SCAN). Press again to cancel.

Folder Scan Play

From the next folder, the ﬁ rst 10 seconds of the ﬁ rst ﬁ le in each folder is played in sequence.

Hold down [5] (SCAN) for 2 sec. or more.

lights.

Hold down again to cancel.

Repeat Play

The current ﬁ le is repeated.

Press [6] (REPEAT). lights. Press again to cancel.

Folder Repeat Play

The current folder is repeated.

Hold down [6] (REPEAT) for 2 sec. or more. lights. Hold down again to cancel.

Display Change

(DISP: Display)

When a disc is already loaded, press [SOURCE] to select the MP3/WMA mode.

Press [OPEN] to open the face plate.

Load a disc with the printed side facing up.

Note: It may take some time to start playing.

Close the face plate manually.

Notes:

• The unit recognizes the disc and starts playing automatically.

• The power will be turned on automatically when a disc is loaded.

Disc Eject



Press [OPEN].



Press [] and take the disc out.



Close the face plate manually.

Folder/File

Play time

(Data reading)

Folder name/Album name*

(Data reading)

File name/title and artist name*

Clock time

Display off

Cautions

• This unit does not support 8 cm discs.

• Do not insert a disc when

indicator lights

because a disc is already loaded.

• Do not use irregularly shaped discs. (

 page 32)

• Do not use discs that have a seal or label attached.

• To avoid damaging the face plate, do not push it down or

place objects on it while it is open.

• Do not pinch your ﬁ nger or hand in the face plate.

• Do not insert foreign matter into the disc slots.

• Refer to the section on “Notes on CD/CD Media (CD-ROM, CD-R, CD-RW)” (

 page 32).

• A disc which has both CD-DA data and MP3/WMA data on it may not be reproduced normally.

• Refer to the section on “Notes on MP3/WMA” (

 page 22).

Press [DISP].

[] (Eject)

Printed side

*ID3/WMA Tag

Setting

Hold down [3] (SCROLL) for 2 sec. or more.

(Default)

When a folder name is displayed:

TAG ON: The album title is displayed. TAG OFF: The folder name is displayed.

When a ﬁ le name is displayed:

TAG ON: The title/artist name is displayed. TAG OFF: The ﬁ le name is displayed.

+ 24 hidden pages