Panasonic CF-W2DWAZZKM User Manual
XP
Personal Computer
OPERATING INSTRUCTIONS
Model No. CF-W2 Series
Contents
Getting Started
Read Me First.................................................. 3
Names and Functions of Parts ...................... 10
First-time Operation ...................................... 12
Reference Manual
• Read Me First • LED Indicators
• Key Combinations
Operation
Starting Up/Shutting Down ............................ 16
Touch Pad ..................................................... 19
Reference Manual .........................................20
RAM Module ................................................. 21
Useful Information ......................................... 23
Page
Getting StartedOperationTroubleshooting
[Additional Manual]
Reference Manual
This manual can be accessed on your computer. Refer to page 20 on how to access the Reference Manual.
Reference Manual
• Touch Pad
• Standby/Hibernation
Functions
• Security Measures
• Computing on the Road
• Battery Power
• SD-MovieStage
•
DVD-ROM & CD-R/RW Drive
• WinDVD
• B’s Recorder/B’s CLiP
• PC Cards
• SD Memory Card/
MultiMedia Card
• SD Memory Card Se-
curity Function
• External Display
• USB Devices
• Modem
• LAN
• Wireless LAN
• Setup Utility
• Icon Enlarger
Troubleshooting
List of Error Codes ......................................... 28
Dealing with Problems (Summary)................... 29
Reinstalling Software .................................... 34
Reference Manual
• Technical Information
• DMI Viewer
• List of Error Codes
• Dealing with Problems
(Advanced)
Appendix
LIMITED USE LICENSE AGREEMENT........ 36
Hard Disk Backup Function ........................... 38
Hard Disk Data Erase Utility .......................... 42
Specifications ................................................ 43
LIMITED WARRANTY................................... 45
Appendix
Please read these instructions carefully before using this product and save this manual for future use.
Customer’s Record
Model No. *
Serial No.
or
Code No.
Date of Purchase
*1For the Model No., insert the 12 digit number (for example, CF-W2DWAZZKM) located
on the bottom of the computer.
Introduction
Thank you for purchasing the Panasonic computer. Read the operating instructions thoroughly for proper operation of your new
computer.
Illustrations and Terminology in this Manual
NOTE: NOTE provides a useful fact or helpful information.
CAUTION: CAUTION indicates a condition that may result in minor or moderate injury.
Enter : This illustration means to press the [Enter] key.
Fn + F5 : This illustration means to press and hold the [Fn] key, then press the [F5] key.
Getting Started
[start] - [Run]: This illustration means to click [start], then to click [Run]. For some applications, you may need to
: Where to go for referred information.
: This illustration means to refer to the Reference Manual, which is available on your computer.
Some of the illustrations in this manual may differ slightly in shape from the actual items in order to make the explanation
easier to understand.
In this manual, “Microsoft® Windows® XP Professional” is indicated as “Windows” or “Windows XP”.
In this manual, the following software packages are described as follows:
“WinDVD™ 5 (OEM Version)” as “WinDVD”
“B’s Recorder GOLD7 BASIC” as “B’s Recorder”
“B’s CLiP 5” as “B’s CLiP”
If the user has logged on without the administrator authority, some functions may not be executable, and some screens may
not be displayed as shown in this manual. If this happens, log on with the administrator authority to enable these functions.
Confirm the latest information on optional products in catalogs, etc.
Circular media such as DVD-ROM and CD-ROM are described as “discs”.
1
When using with the [Fn] and [Ctrl] functions interchanged, read with [Fn] and [Ctrl] reversed.
( “Key Combinations”)
double-click.
Refer to page 20 on how to access this manual.
Dealer’s Name
Dealer’s Address
Copyright
This manual is copyrighted by Matsushita Electric Industrial Co., Ltd. with all rights reserved. No part of this manual may be
reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.
No patent liability is assumed with respect to the use of the information contained herein.
©2004 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
Disclaimer
Computer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes no
liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.
Trademarks
Microsoft, Windows and the Windows logo are registered trademarks of Microsoft Corporation of the United States and/or other
countries.
Intel, Pentium and PROSet are either registered trademarks or trademarks of Intel Corporation.
SD Logo is a trademark.
Adobe® and Acrobat® are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or
other countries.
WinDVD™ is a trademark of InterVideo, Inc.
Panasonic is a registered trademark of Matsushita Electric Industrial Co., Ltd.
Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies.
2
Read Me First
For U.S.A.
Federal Communications Commission Radio
Frequency Interference Statement
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the Panasonic Service Center or an experienced radio/TV technician for help.
Warning
To assure continued compliance, use only shielded interface
cables when connecting to a computer or peripheral. Also,
any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this equipment.
FCC RF Exposure Warning:
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment.
This equipment must be installed and operated in accordance
with provided instructions and minimum 1.5 cm spacing must
be provided between antenna and all person’s body (excluding
extremities of hands, wrist and feet) during wireless modes of
operation.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This computer
is provided with a PC Card slot that could be used with wireless transmitter(s), which will be specifically recommended,
when they become available. Other third-party wireless
transmitter(s) have not been RF exposure evaluated for use
with this computer and may not comply with FCC RF exposure requirements.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party: Matsushita Electric Corporation of America
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP-5 (1-800-527-8675)
FCC Regulation Notice for modem
This equipment contains a FCC approved modem.
Manufacturer of modem: PC TEL Inc.
Model No. PCT2304WT
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
1. This equipment complies with CFR47 Part 68 rules. On the
computer is a label that contains, among other information,
the FCC registration number and ringer equivalence number
(REN) for this equipment. If required, this information must
be provided to the telephone company.
2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be
connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant.
See Installation Instructions for details.
3. The REN is used to determine the quantity of devices which
may be connected to the telephone line. Excessive RENs on the
telephone line may result in the devices not ringing in response
to an incoming call. In most, but not all area, the sum of RENs
should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company.
4. If your telephone equipment cause harm to the telephone
network, the telephone company will notify you in advice
that temporary discontinuance of service may be required.
But if advice notice isn’t practical, the telephone company
will notify the customer as soon as possible. Also, you will
be advised of your right to file a complaint with the FCC if
you believe it is necessary.
5. The telephone company may take changes in it’s facilities,
equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
6. If trouble is experienced with this equipment, for repair or
warranty information, please contact Matsushita Electric
Corporation of America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm
to the telephone network, the telephone company may request that you disconnect the equipment until the problem is
resolved.
7. There are no user serviceable parts contained in this equipment.
8. This equipment may not be used on coin service provided
by the telephone company. Connection to party lines is subject to state tariffs.
9. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic
device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or
bottom of each transmitted page or on the first page of the
transmission, the date and time it is sent and an identification
of the business or other entry, or other individual sending the
message and the telephone number of the sending machine or
such business, other entity, or individual. In order to program
this information into your fax software, you should refer to
the manual of the Fax software being used.
Getting Started
3
Read Me First
10.According to the FCC’s electrical safety advisory, we recommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected. Telephone companies report that electrical surges, typically lightning transients,
are very destructive to customer terminal equipment connected
to AC power sources and that this is a major nationwide problem.
“Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.”
“ATTENTION: Pour réduire le risque d’incendie, utiliser uniquement des
conducteurs de télécommunications 26 AWG ou de section supérieure.”
For Canada
Industry Canada (IC) Notice for modem
This equipment contains an Industry Canada approved modem
unit.
The Industry Canada label is affixed on the modem unit.
EQUIPMENT ATTACHMENT LIMITATIONS
“NOTICE: The Industry Canada label identifies certified
Getting Started
equipment. This certification means that the equipment meets
telecommunications network protective, operational and
safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The
Department does not guarantee the equipment will operate
to the user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas. Caution: Users should not attempt to make such
connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.”
“NOTICE: The Ringer Equivalence Number (REN) assigned
to each terminal device provides an indication of the
maximum number of terminals allowed to be connected to
a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.”
REN: See bottom of the computer
Notice for the products using LCD
This product uses one or more fluorescent lamps containing a
small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or
recycling information please contact your local authorities, or
the Electronics Industries Alliance: <http://www.eiae.org/>
RESTRICTIONS CONCERNANT LE RACCORDEMENT
DE MATÉRIEL
“AVIS: L’étiquette d’Industrie Canada identifie le matériel
homologué. Cette étiquette certifie que le matériel est
conforme aux normes de protection, d’exploitation et de
sécurité des réseaux de télécommunications, comme le
prescrivent les documents concernant les exigences
techniques relatives au matériel terminal. Le Ministère
n’assure toutefois pas que le matériel fonctionnera à la
satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il
est permis de le raccorder aux installations de l’entreprise
locale de télécommunication. Le matériel doit également
être installé en suivant une méthode acceptée de
raccordement. L’abonné ne doit pas oublier qu’il est possible
que la conformité aux conditions énoncées ci-dessus
n’empêche pas la dégradation du service dans certaines
situations.
Les réparations de matériel homologué doivent être
coordonnées par un représentant désigné par le fournisseur.
L’entreprise de télécommunications peut demander à
l’utilisateur de débrancher un appareil à la suite de
réparations ou de modifications effectuées par l’utilisateur
ou à cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous
les fils de mise à la terre de la source d’énergie électrique,
des lignes téléphoniques et des canalisations d’eau
métalliques, s’il y en a, sont raccordés ensemble. Cette
précaution est particulièrement importante dans les régions
rurales. Avertissement: L’utilisateur ne doit pas tenter de faire
ces raccordements lui-même; il doit avoir recours à un
service d’inspection des installations électriques, ou à un
électricien, selon le cas.”
“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné
à chaque dispositif terminal indique le nombre maximal de
terminaux qui peuvent être raccordés à une interface. La
terminaison d’une interface téléphonique peut consister en
une combinaison de quelques dispositifs, à la seule condition
que la somme d’indices d’équivalence de la sonnerie de touts
les dispositifs n’excède pas 5.”
IES: Voir sous le fond de l’ordinateur
Industry Canada
This product complies with RSS210 Industry Canada.
Operation is subject to the following two conditions;
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
4
Important Safety Instructions / Importantes Mesures De Sécurité
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during
an electrical storm. There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of
the leak.
4. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries in a fire. They may explode. Check
with local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS
For Europe
Declaration of Conformity (DoC)
“Hereby, we and Panasonic Testing Centre (Europe) GmbH (PTC), declares that this Personal Computer is in
compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”
Hint:
If you want to get a copy of the original DoC of our products which relates to the R&TTE, please contact to our
web address: http://doc.panasonic-tc.de
Certaines mesures de sécurité doivent être prises pendant l’utilisation
de matérial téléphonique afin de réduire les risques d’incendie, de
choc électrique et de blessures. En voici quelquesunes:
1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire,
d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un
sous-sol humide ou près d’une piscine.
2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans
fil) pendant un orage électrique. Ceci peut présenter un risque
de choc électrique causé par la foudre.
3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de
gaz s’il est situé près de la fuite.
4. Utiliser seulement le cordon d’alimentation et le type de piles
indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles
peuvent exploser. Se conformer aux règlements pertinents quant
à l’élimination des piles.
CONSERVER CES INSTRUCTIONS
Getting Started
Network connection.
The terminal equipment is intended for connection to the following public network;
In all the countries of European Economical Area;
- Public Switched Telephony Networks
Technical Features.
The terminal equipment includes the following features;
- DTMF dialing
- Maximum bitrate receiving mode: 56 kbits/s
- Maximum bitrate sending mode: 33.6 kbit/s
This product is designed to interwork with the Public Switched Telecommunication Networks in UK, Ireland, Netherlands, Sweden, Denmark, Finland, Switzerland, Luxembourg, Belgium, France, Germany, Spain, Portugal, Iceland, Greece, Italy, Norway
and Austria.
--------------------------------------------------------------------------------------------------------------------------------------------
Compliance Notice - CE Mark
This equipment is in conformance with the requirements of the European Council Directive listed below:
73/23/EEC Low Voltage Directive with amendment 93/68/EEC
89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC
1999/5/EC
--------------------------------------------------------------------------------------------------------------------------------------------
5
Read Me First
For U.K. and Hong Kong
Warning
This apparatus must be earthed for your safety.
To ensure safe operation the three-pin plug must be inserted
only into a standard three-pin power point which is effectively
earthed through the normal household wiring.
Extension cords used with the equipment must be three-core
and be correctly wired to provide connection to earth. Wrongly
wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is
completely safe.
For your safety, if you have any doubt about the effective
earthing of the power point, consult a qualified electrician.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded three pin mains plug
Getting Started
for your safety and convenience.
A 3 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 amps and that it is approved by
ASTA or BSI to BS 1362.
Check for the ASTA mark
of the fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE
SHOULD BE REMOVED AND THE PLUG CUT OFF AND
DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK
IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP
SOCKET.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt please consult a qualified electrician.
A S A
or the BSI mark on the body
Warning: THIS APPLIANCE MUST BE EARTHED.
Important
The wires in this mains lead are coloured in accordance with
the following code:
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be
connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol coloured GREEN or
GREEN-and-YELLOW.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured RED.
The mains plug on this equipment must be used to disconnect
the mains power.
Please ensure that a socket outlet is available near the equipment and shall be easily accessible.
How to replace the fuse
Open the fuse compartment
with a screwdriver and replace
the fuse.
Warnings
This equipment is not designed for connection to an IT power
system.
(An IT system is a system having no direct connections between live parts and Earth; the exposed-conducive-parts of
the electrical installation are earthed.
An IT system is not permitted where the computer is directly
connected to public supply systems in the U.K.)
Disconnect the mains plug from the supply socket when the
computer is not in use.
This equipment is produced to BS800/1983.
6
Information to the User
This product and your Health
This product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this product
however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Because this product operates within the guidelines found in radio frequency safety standards and recommendations, we believe this
product is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and
result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
In some situations or environments, the use of this product may be restricted by the proprietor of the building or responsible
representatives of the organization. These situations may for example include:
Using this product on board of airplanes, or
In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports),
you are encouraged to ask for authorization to use this product prior to turning on the product.
Regulatory Information
We are not responsible for any radio or television interference caused by unauthorized modification of this product. The correction
of interference caused by such unauthorized modification will be the responsibility of the user. We and its authorized resellers or
distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these
guidelines.
Lithium Battery
Lithium Battery!
This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged
by authorized service personnel.
Warning! A risk of explosion from incorrect installation or misapplication may possibly occur.
Getting Started
Pile au lithium!
Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données comme la date et l’heure notamment.
Elle ne devra être remplacée que par un technicien qualifié.
Avertissement! Risque d’explosion en cas de non respect de cette mise en garde!
DVD-ROM & CD-R/RW Drive Caution
Bottom
CLASS 1 LASER PRODUCT
LASER KLASSE1
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL
AVERTISSEMENT!
CET APPAREIL UTILISE UN LASER.
L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU
L’EXÉCUTION DE PROCÉDURES AUTRES QUE CELLES
SPÉCIFIÉES ICI PEUVENT PROVOQUER UNE EXPOSITION À DES RADIATIONS DANGEREUSES.
NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE
RÉPARER SOI-MÊME.
CONFIER TOUT TRAVAIL D'ENTRETIEN À UN PERSONNEL QUALIFIÉ.
7
Read Me First
Precautions
Usage Handling
Avoid Extreme Heat and Cold
Do not store or use the computer in locations
exposed to heat, direct sunlight, or extreme cold.
Avoid moving the computer between locations with
large temperature difference.
Operation: 5 oC to 35 oC {41 oF to 95 oF}
Storage: -20 oC to 60 oC {-4 oF to 140 oF}
Avoid Direct Sunlight on the LCD Panel
The LCD panel should not be exposed to direct
sunlight or ultraviolet light.
Avoid Humidity, Liquids and Dust
Do not store or use the computer in locations exposed to high humidity, liquids (including rain) or
Getting Started
dust.
Prevent Shock
Avoid subjecting the computer to severe vibrations
or impact. Do not place the computer inside a car
trunk.
Avoid Radio Frequency Interference
Do not place the computer near a television or radio receiver.
Avoid Magnetic Fields
Keep the computer away from magnets.
Data stored on the hard disk may be lost.
Avoid Stacking
Do not place heavy objects on top of the computer.
Keep Small Objects Away
Do not insert paper clips or other small objects into
the computer.
Do Not Disassemble the Computer
Do not attempt to disassemble your computer.
Avoid Excessive Force on the Display
Do not apply excessive downward force on the
display.
Avoiding low-temperature burns
Avoid more than casual contact with any heat producing area of the notebook computer, AC adaptor, and any option or accessory you use with it.
Even low heat, if warmer than body temperature,
can cause a burn, if the skin is exposed to the heat
source for a long enough period of time.
Do not touch the AC plug and modem telephone
cable when it starts thundering.
Keep SD memory cards and MultiMedia cards
(both sold separately) away from infants and
small children.
Accidental swallowing will result in bodily injury.
In the event of accidental swallowing, see a doctor
immediately.
8
Precautions (Battery Pack)
Care should be exercised with regard to the following in
order to avoid the possibility of overheating, fire or damage.
Avoid Heat
Do not throw the battery pack into a fire or
expose it to excessive heat.
Keep Articles Away
Do not place the battery pack together with articles such as necklaces or hairpins when carrying or storing.
Do Not Disassemble
Do not insert sharp objects into the battery pack,
expose it to bumps or shocks, deform, disassemble, or modify it.
Do Not Short
Do not short the positive (+) and negative (-)
contacts.
Avoid Extreme Heat, Cold and Direct Sunlight
Do not charge, use or leave the battery pack for
extended periods where it will be exposed to
direct sunlight, in a hot place (in a car on a sunny
day, for example), or in a cold place.
Do Not Use With Any Other Computer
The battery pack is rechargeable and was intended for the specified computer. Do not use
it with a computer other than the one for which
it was designed.
Do Not Put into a Microwave
Do not put the battery pack into a microwave
oven or a pressurized chamber.
Stop Using
Should the battery emit an abnormal odor, become hot to the touch, become discolored,
change shape, or become in any way different
from normal, remove it from the computer and
stop using it.
If the battery pack will not be used for a long period of time
(a month or more), charge or discharge (use) the battery
pack until the remaining battery level becomes 30% to 40%
and store it in a cool, dry place.
This computer prevents overcharging of the battery by recharging only when the remaining power is less than
approx. 95% of capacity.
The battery pack is not charged when the computer is first
purchased. Be sure to charge it before using it for the first
time. When the AC adaptor is connected to the computer,
charging begins automatically.
Should the battery leak and the fluid get into your eyes, do
not rub your eyes. Immediately flush your eyes with clear
water and see a doctor for medical treatment as soon as possible.
NOTE
The battery pack may become warm during recharging or normal use. This is completely normal.
Recharging will not commence outside of the allowable temperature range (0 °C to 55 °C {32 °F to 131
°F}). ( “Battery Power”) Once the allowable
range requirement is satisfied, charging begins auto-
matically. Note that the recharging time varies based
on the usage conditions. (Recharging takes longer than
usual when the temperature is 10 °C {50 °F} or less.)
If the temperature is low, the operating time is shortened. Only use the computer within the allowable temperature range.
The battery pack is a consumable item. If the amount
of time the computer can be run off a particular battery
pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery
pack should be replaced with a new one.
When transporting a spare battery inside a package,
briefcase, etc., it is recommended that it be placed in a
plastic bag so that its contacts are protected.
Always power off the computer when it is not in use.
Leaving the computer on when the AC adaptor is not
connected will exhaust the remaining battery capacity.
Getting Started
Do not touch the terminals on the battery pack. The battery
pack may no longer function properly if the contacts are
dirty or damaged.
Do not expose the battery pack to water, or allow it to become wet.
9
Names and Functions of Parts
Function Keys
For information on the key combinations available.
( “Key Combinations”).
Keyboard
Touch Pad
( page 19)
Getting Started
Modem
Power Switch
( “Modem”)
LCD
LED Indicators
( “LED Indicators”)
Power status
Battery pack status
Caps Lock
Numeric Key (NumLk)
Scroll Lock (ScrLk)
Hard disk drive status
DVD-ROM & CD-R/RW drive
status
Speaker
To adjust the volume:
Fn + F5 / Fn + F6
Speaker on/off : Fn + F4
CAUTION
Security Lock
A Kensington cable can be connected to prevent theft of your
computer.
For more information, read the
manual that comes with cable.
LAN
( “LAN”)
PC Card Slot
( “PC Cards”)
SD Memory Card Slot
SD memory card status
( “SD Memory Card/
MultiMedia Card”)
CAUTION
Do not allow metallic objects or magnetic media to come near this area.
10
Do not allow metallic objects or magnetic media to come near the speaker.
Wireless LAN
( page 26, “Wireless LAN”)
DC-IN Jack
External Display Port
( “External Display”)
USB Ports
( “USB Devices”)
Microphone Jack
Use only a monaural condenser microphone (miniature jack).
Using an input source other than a monaural condenser microphone may not allow audio to be input or may damage
the equipment.
Headphone Jack
Use this jack to connect headphones or amplifier-equipped
speakers. Audio output from the internal speaker is disabled
when headphones or external speakers are connected.
DC IN 16V
CAUTION
Do not allow metallic objects or magnetic media to come near this area.
Getting Started
DVD-ROM & CD-R/RW Drive
( “DVD-ROM & CD-R/RW Drive”)
Open Lever
Slide the lever to open the disc cover. This works only
when the power is on.
When using the drive for the first time, slide the open
lever to open the disc cover after the computer has been
powered on, and remove the protective sheet from the
lens area.
A lithium ion battery that is
recyclable powers the product you have purchased.
Please call 1-800-8-BATTERY for information on
how to recycle this battery.
L’appareil que vous vous
êtes procuré est alimenté par
une batterie au lithium-ion.
Pour des renseignements sur
le recyclage de la batterie,
veuillez composer le 1-8008-BATTERY.
CAUTION
Do not cover the computer with
a thick cloth, such as a blanket.
Latch
(This latch is locked manually)
Battery Pack
( “Battery Power”)
Latch
(This latch is locked automatically)
RAM Module Slot
( page 21)
Emergency Hole
( page 27, “DVD-ROM & CD-R/RW Drive”)
11
First-time Operation
Read the steps below to help you learn what parts are included, and to gain an understanding of
some basic computer-related operations.
Confirm the inclusion of all parts.
1
Make sure the parts shown in the figure have been supplied. If any of these items are
missing or is not working properly, contact your technical support office ( page 45).
Getting Started
AC adaptor ..........1
Model No : CF-AA1623A
Product Recovery
DVD-ROM ............1
2
Read the LIMITED USE LICENSE AGREEMENT. ( page 36)
Be sure to read the LIMITED USE LICENSE AGREEMENT before breaking the seal
on the computer’s packaging.
3
Turn the computer over and insert the battery pack.
1 Slide the left-side latch (A) to the unlock position ( ).
2 Make sure the battery pack is facing the correct direction, slide it in the direction of
the arrow.
3 Slide the left-side latch to the lock position ( ), and then check to ensure that the
battery pack is held firmly.
(Right-side latch is locked automatically.)
AC Cord ...............1
Modem Telephone
Cable ...................1
Battery Pack........1
Model No :CF-VZSU27
Operating Instructions
(This book)
Windows® Book .... 1
.................... 1
CAUTION
Confirm that the latch is properly locked. If it is not, the battery pack may come
off while you are carrying around the computer.
Do not touch the terminals on the battery pack and the computer. The battery
pack may no longer function properly if the contacts are dirty or damaged. Also,
the computer may not operate properly.
Before using the battery pack, carefully read “Precautions (Battery Pack)”
( page 9).
Open the display.
4
1 Slide the latch (B) located at the front.
2 Lift open the display.
CAUTION
Do not open the display wider than necessary (135° or more).
Do not apply excessive pressure to the LCD (C). Also, do not hold the LCD
when opening or closing the display.
12
Connect your computer to a power outlet.
5
The battery pack will be charged automatically.
Charging Time: Approx. 4.5 hours
(Varies depending on the usage conditions.)
CAUTION
Be sure the AC adaptor is connected until completing the first-time use operation.
When using the computer for the first time, do not connect any peripheral device except the battery pack and AC adaptor to the computer.
Handling the AC adaptor
Do not twist or pull the AC power cord forcefully. Doing so may damage the
connections.
Use only the specified AC adaptor with your computer. Using an AC adaptor
other than the one supplied might damage the battery and/or the computer.
When the DC plug is not connected to the computer, disconnect the AC cord
from your AC wall outlet.
Problems such as sudden voltage drops may arise during periods of thunder
and lightning. Since this could adversely affect your computer, an uninterruptible
power source (UPS) is highly recommended unless running from the battery
pack alone.
6
Turn your computer on.
Slide the power switch and hold it for approximately one second until the power
indicator turns on before releasing it.
Getting Started
CAUTION
Do not slide the power switch and hold it for more than four seconds; this will
cause the power to be turned off forcibly.
Do not slide the power switch repeatedly.
Once the computer is powered off, you must wait at least ten seconds before
powering it on again.
7
Setup Windows.
Moving the cursor or clicking buttons can be performed with the touch pad
( page 19).
CAUTION
Do not press any keys or touch the touch pad until [Windows XP Professional
Setup] is displayed.
1 At [Welcome to the Windows XP Setup Wizard], select [Next].
2 After reading the agreement, select [I accept this agreement] or [I don’t accept this
agreement], then select [Next].
NOTE
If [I don’t accept this agreement] is selected, the Windows setup will be
aborted.
3 Select settings for your region, then select [Next].
4 Enter your name and organization and then select [Next].
13
First-time Operation
5 Enter your computer name and administrator password and then select [Next].
CAUTION
Remember this password! If the password is forgotten, Windows cannot be
operated.
6 Enter the correct date, time and the time zone, then select [Next].
NOTE
It may take some time before the computer restarts and the screen of step
7 is displayed. Wait, and do not press any keys, or touch the touch pad, etc.
If the keyboard or the touch pad etc. are operated, a message will appear
indicating that there is no response on the screen, or some screens may
appear white. In such cases, also wait until the next screen is displayed.
The computer will restart.
7 Enter your administrator password and select .
Getting Started
8
Create a new account.
1 Select [start] - [Control Panel] - [User Accounts] - [Create a new account].
2 Enter a new name for the new account, then select [Next].
3 Select [Computer administrator], then select [Create Account].
4 <When you want to create a password for the new account>
Select the new account you have created and select [Create a password].
Follow the instructions on the screen to create a password.
5 Select [start] - [Turn Off Computer] - [Restart] to restart the computer.
CAUTION
Remember this password! If the password is forgotten, Windows cannot be
operated. You can create a password reset disk beforehand ( page 15).
NOTE
When creating a new user account:
If you make mail settings, create password reset disks ( page 15), or
conduct other related operations before creating the user account, you will
be unable to use any previous mail history or settings.
When you create the first new account, you can only select [Computer administrator].
Once a “Computer Administrator” account has been created, you can create
additional limited user accounts.
Note also that only the added user account will be displayed in the Welcome screen. The account for the administrator created during Windows
setup will not be displayed.
About the Icon Enlarger:
If the characters or icons on the screen are too small and difficult to see,
after completing step 8, select [start] - [All Programs] - [Panasonic] - [Icon
Enlarger]. This will allow you to magnify the display of characters and
icons on the screen. ( “Icon Enlarger”)
The [Icon Enlarger] can be set separately for each account.
14
9
Start up Windows® Media Player.
Log on with the administrator authority, and select on the desktop.
After this, start up the application following the instructions on the screen.
During this process, you will be required to agree to the license agreement.
For Windows® Media Player, it is necessary to agree to the license agreement for
each account created.
If [I Decline] is selected or a window is closed without any decision being made in
the license agreement, no icons on the desktop may be selected. In this case, restart
the computer.
To have DVD video and MPEG files played back automatically on WinDVD, remove the check mark from [DVD Video] and [Movie file (mpeg)] on screen A or
on the left.
A
. When starting up Windows® Media Player for the first time, one of the setting
screens will be displayed.
B
. After starting up Windows® Media Player, the screen will be displayed when [Tools]
- [Options] - [File Types] is selected.
After completing the settings, select on the screen of the Windows® Media Player.
NOTE
To improve the security of the computer, be sure to refer to “Security of the Computer” and “Windows Update”. ( page 25)
If you use the wireless LAN, be sure to refer to “Wireless LAN”. ( page 26)
B
Getting Started
This concludes the first-time use operation guidelines.
Information for Windows XP
Depending on the Windows settings, installed applications, and drivers, menus and
other displays may differ, or some functions (such as use of the password reset disk)
may be inoperable. Check with your system administrator for details.
You can select Classic view for the Control Panel or select the Classic Start menu.
You can also change the way a user logs on or off.
The procedure in this manual uses the method or view of the Windows XP default
setting (not Classic view nor Classic Start menu etc.).
Resetting the password
Windows XP has a function to reset a forgotten password.
To use this function, you need to create a password reset disk beforehand following
the steps below.
1
2
3
Connect the USB floppy disk drive (optional: CF-VFDU03) to your computer.
Select [start] - [Control Panel] - [User Accounts].
Select [Prevent a forgotten password] from [Related Tasks] menu of the account
you used to logon and create a password reset disk following the on-screen instructions.
Store the password reset disk in a safe place.
Only the logon password for each account can be reset.
·
The password set in the Setup Utility cannot be reset.
15
Loading...