Panasonic BLVT164P User Manual

Operating Instructions

BL-VT164W BL-VP104W

Network Camera

Model No. BL-VT164 Series

BL-VP100 Series

This manual covers the models: BL-VT164 Series (BL-VT164W, BL-VT164, BL-VT164WE, BL-VT164E, BL-VT164WU, BL-VT164U) and BL-VP100 Series (BL-VP104W, BL-VP104, BL-VP101, BL-VP104WE, BL-VP104E, BL-VP101E, BL-VP104WU, BL-VP104U, BL-VP101U).

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

The model number is abbreviated in some descriptions in this manual.

VT164W

VT164

VP104W

VP104

VP101

Preface

About the user manuals

There are 2 sets of operating instructions for the BL-VT164W, BL-VT164, BL-VP104W, BL-VP104, BL-VP101 (P model), BL-VT164WE, BL-VT164E, BL-VP104WE, BL-VP104E, BL-VP101E (E model), BL-VT164WU, BL-VT164U, BL-VP104WU, BL-VP104U, BL-VP101U (U model) as follows.

• Installation Guide: Explains how to install and connect devices.

When you use the BL-VT164W/BL-VT164WE/BL-VT164WU or BL-VT164/BL-VT164E/BL-VT164U, refer to BL-VT164W/BL-VT164WE/BL-VT164WU/BL-VT164/BL-VT164E/BL-VT164U Installation Guide. When you use the BL-VP104W/BL-VP104WE/BL-VP104WU, BL-VP104/BL-VP104E/BL-VP104U, or BL-VP101/BL-VP101E/BL-VP101U, refer to BL-VP100 Series Installation Guide.

• Operating Instructions: Explains how to perform the settings and how to operate this camera. This

Operating Instructions covers the models: BL-VT164W, BL-VT164, BL-VP104W, BL-VP104, BL-VP101, BL-VT164WE, BL-VT164E, BL-VP104WE, BL-VP104E, BL-VP101E, BL-VT164WU, BL-VT164U,

BL-VP104WU, BL-VP104U, BL-VP101U. The model number is abbreviated in some descriptions in this manual. The screens used in these operating instructions show the case of BL-VT164 (P model). Depending on the model used, the screens shown in the explanations may differ to the actual camera screens.

About notations

The following notations are used when describing the functions limited for specified models. The functions without the notations are supported by all models.

: The functions with this notation are available when using the model BL-VT164W. : The functions with this notation are available when using the model BL-VT164. : The functions with this notation are available when using the model BL-VP104W. : The functions with this notation are available when using the model BL-VP104. : The functions with this notation are available when using the model BL-VP101.

Trademarks and registered trademarks

• Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX and DirectX are either registered

trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

• iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

• Android is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.

• All other trademarks identified herein are the property of their respective owners.

Abbreviations

The following abbreviations are used in these operating instructions. Microsoft® Windows® 7 is described as Windows 7. Microsoft® Windows Vista® is described as Windows Vista. Microsoft® Windows® XP SP3 is described as Windows XP. Windows® Internet Explorer® 9.0, Windows® Internet Explorer® 8.0, Windows® Internet Explorer® 7.0 and Microsoft® Internet Explorer® 6.0 are described as Internet Explorer.

2 Operating Instructions

Universal Plug and Play is described as UPnP™ or UPnP.

Viewer software

It is necessary to install the viewer software “Network Camera View 4S” to display images on a PC. This software can be installed directly from the camera or by selecting the [Install] button next to [Viewer Software] on the menu of the CD-ROM provided, and then following the on-screen instructions.

Preface

IMPORTANT

• The default setting of “Automatic installation of viewer software” is “On”. Follow the instructions on

page 178 when the message is displayed on the information bar of the browser.

• When the “Live” page is displayed for the first time, the install wizard of the ActiveX

to display images from the camera will be displayed. Follow the instructions of the wizard.

• When the install wizard is displayed again even after completing the installation of the ActiveX, restart

the PC.

• The viewer software used on each PC should be licensed individually. The number of installations of

the viewer software from the camera can be checked on the [Upgrade] tab of the “Maintenance” page (®page 154). Refer to your dealer for the software licensing.

control required

Operating Instructions 3

Table of Contents

1 Monitor images on a PC ..........................................................................7

1.1 Monitor images from a single camera .............................................................................7

1.2 About the “Live” page (BL-VT164W/BL-VT164) ...........................................................10

1.3 About the “Live” page (BL-VP104W/BL-VP104/BL-VP101) .........................................15

1.4 Monitor images from multiple cameras ........................................................................18

2 Monitor images on a cellular phone/mobile terminal .........................19

2.1 Monitor images on a cellular phone ..............................................................................19

2.2 Monitor images on a mobile terminal ............................................................................22

3 Action at an alarm occurrence ..............................................................30

3.1 Alarm type ........................................................................................................................30

3.2 Action at an alarm occurrence .......................................................................................30

4 Transmit images onto an FTP server ...................................................32

4.1 Transmit an alarm image at an alarm occurrence (Alarm image

transmission) ...................................................................................................................32

4.2 Transmit images at a designated interval or period (FTP periodic image

transmission) ...................................................................................................................32

5 About the network security ...................................................................33

5.1 Equipped security functions ..........................................................................................33

6 Display the setup menu from a PC .......................................................34

6.1 How to display the setup menu .....................................................................................34

6.2 How to operate the setup menu .....................................................................................35

6.3 About the setup menu window ......................................................................................37

7 Configure the basic settings of the camera [Basic] ...........................39

8 Configure the Internet settings [Internet] ............................................44

9 Configure the settings relating to images and audio [Image/Audio]

(BL-VT164W/BL-VT164)/ Configure the settings relating to images

[Image] (BL-VP104W/BL-VP104/BL-VP101) .........................................46

9.1 Configure the settings relating to the aspect ratio [JPEG/H.264] ..............................46

9.2 Configure the settings relating to JPEG images [JPEG/H.264] ..................................47

9.3 Configure the settings relating to H.264 images [JPEG/H.264] ..................................49

9.4 Configure the settings relating to the camera operations [Cam. Function]

(BL-VT164W/BL-VT164) ..................................................................................................55

9.5 Configure the settings relating to images and the preset positions [Image/Position] (BL-VT164W/BL-VT164)/ Configure the settings relating to image adjust, extra zoom,

and privacy zone [Image/Privacy] (BL-VP104W/BL-VP104/BL-VP101) ......................57

9.5.1 Configure the settings relating to image quality (“Image adjust” setup menu) ...............58

9.5.2 Set mask areas ..............................................................................................................62

9.5.3 Configure the settings relating to the preset positions (“Preset position” setup menu)

(BL-VT164W/BL-VT164) ................................................................................................65

9.5.3.1 Register the preset positions .......................................................................................66

9.5.4 Adjust the angular field of view using the extra zoom function (BL-VP104W/

BL-VP104) ......................................................................................................................68

9.5.5 Configure the settings relating to the privacy zone (“Privacy zone” setup menu)

(BL-VT164W/BL-VT164) ................................................................................................68

4 Operating Instructions

Table of Contents

9.5.6 Configure the settings relating to the privacy zone (“Privacy zone” setup menu)

(BL-VP104W/BL-VP104/BL-VP101) ..............................................................................70

9.6 Configure the settings relating to audio [Audio] (BL-VT164W/BL-VT164) ................72

10 Configure the multi-screen settings [Multi-screen] ............................75

11 Configure the alarm settings [Alarm] ...................................................77

11.1 Configure the settings relating to the alarm action [Alarm] .......................................77

11.2 Configure the settings relating to the camera action on alarm occurrence [Alarm]

(BL-VT164W/BL-VT164) ..................................................................................................79

11.3 Configure the settings relating to the alarm image [Alarm] ........................................80

11.4 Configure the settings relating to the alarm output terminal [Alarm] (BL-VT164W/

BL-VT164) ........................................................................................................................82

11.5 Change the AUX name [Alarm] (BL-VT164W/BL-VT164) .............................................83

11.6 Configure the VMD settings [VMD area] .......................................................................84

11.7 Configuration of the settings relating to the E-mail notification [Notification] .........87

11.8 Configure the settings relating to Panasonic alarm protocol [Notification] .............88

12 Configure the setting relating to the image recognition [Advanced

func.] .......................................................................................................91

12.1 Configure the settings relating to the XML notification [XML notification] ...............91

12.2 Configuration of the settings relating to the face detection [Face detection] ..........93

13 Configure the settings relating to the authentication [User

mng.] .......................................................................................................94

13.1 Configure the settings relating to the user authentication [User auth.] ....................94

13.2 Configure the settings relating to the host authentication [Host auth.] ....................95

13.3 Configure the settings relating to the priority stream [System] .................................96

14 Configure the settings of the servers [Server] ....................................99

14.1 Configure the settings relating to the E-mail server [E-mail] .....................................99

14.2 Configure the settings relating to the FTP server [FTP] ...........................................100

14.3 Configure the settings relating to the NTP server [NTP] ...........................................101

15 Configuring the network settings [Network] .....................................104

15.1 Configure the network settings [Network] ..................................................................104

15.2 Configure the HTTPS settings .....................................................................................112

15.2.1 Generation of the CRT key (SSL encryption key) ........................................................113

15.2.2 Generation of the self-signed certificate (security certificate) .......................................114

15.2.3 Generation of CSR (Certificate Signing Request) ........................................................116

15.2.4 Installation of the server certificate ...............................................................................117

15.2.5 Configuration of the connection protocol ......................................................................118

15.3 Access the camera using the HTTPS protocol ..........................................................119

15.3.1 Install the security certificate ........................................................................................119

15.4 Configure the settings relating to DDNS [DDNS] .......................................................129

15.4.1 Configuration of the DDNS service (Example of the “Viewnetcam.com” service) ........130

15.4.2 When using the “Viewnetcam.com” service .................................................................131

15.4.3 Procedure to register information for the “Viewnetcam.com” service ...........................132

15.4.4 Checking the information registered for the “Viewnetcam.com” service ......................133

15.4.5 When using “Dynamic DNS Update” ............................................................................133

15.4.6 When using “Dynamic DNS Update(DHCP)” ...............................................................134

15.5 Configure the settings relating to SNMP [SNMP] ......................................................134

15.6 Configure the settings relating to the FTP periodic image transmission [FTP img.

trans.] .............................................................................................................................135

Operating Instructions 5

Table of Contents

15.7 Configure the schedule settings of the FTP periodic image transmission [FTP img.

trans.] .............................................................................................................................137

15.7.1 How to set the schedules .............................................................................................137

15.7.2 How to delete the set schedule ....................................................................................138

16 Use the camera on a wireless LAN [Wireless] (BL-VT164W/

BL-VP104W) ..........................................................................................140

16.1 Manually connecting the camera to a wireless LAN (manual settings)

[Basic] ............................................................................................................................140

16.2 Connecting the camera to a wireless LAN with WPS (automatic settings)

[Basic] ............................................................................................................................144

16.3 Using the camera's Wireless QoS [Basic] ..................................................................148

16.4 Confirming the camera's wireless information [Status] ............................................148

17 Configure the settings relating to the schedules [Schedule] ..........151

18 Maintenance of the camera [Maintenance] ........................................154

18.1 Check the system log [System log] .............................................................................154

18.2 Upgrade the firmware [Upgrade] .................................................................................154

18.3 Check the status [Status] .............................................................................................156

18.4 Reset the settings/Reboot the camera [Default reset] ...............................................157

19 Privacy Mode (BL-VT164W/BL-VT164) ...............................................159

19.1 Configuring the Privacy Mode with the PRIVACY button .........................................159

19.2 Configuring the Privacy Mode with the setup menu .................................................160

19.3 Turning the Privacy Mode off .......................................................................................160

20 Using the CD-ROM ...............................................................................161

20.1 About the CD launcher .................................................................................................161

20.2 Installing Panasonic “IP Setting Software” ................................................................162

20.3 Installing the manuals ..................................................................................................163

20.4 Installing the Viewer software ......................................................................................163

20.5 Configure the network settings of the camera using the Panasonic “IP Setting

Software” .......................................................................................................................164

21 About the displayed system log .........................................................166

22 Troubleshooting ...................................................................................170

6 Operating Instructions

1 Monitor images on a PC

The following are descriptions of how to monitor images from the camera on a PC.

1.1 Monitor images from a single camera

1. Start up the web browser.

2. Enter the IP address designated using the Panasonic “IP Setting Software” in the address box of the

browser.

• Example when entering an IPv4 address: http://URL registered using IPv4 address

http://192.168.0.10/

• Example when entering an IPv6 address: http://[URL registered using IPv6 address]

http://[2001:db8::10]/

IMPORTANT

• When the HTTP port number is changed from “80”, enter “http://IP address of the camera + : (colon)

+ port number” in the address box of the browser. (Example: http://192.168.0.11:8080)

• When the PC is in a local network, configure the proxy server setting of the web browser (under

[Internet Options...] under [Tools] of the menu bar) to bypass the proxy server for the local address.

Note

• Refer to page 119 for further information about the case in which “HTTPS” is selected for

“HTTPS” - “Connection” on the [Network] tab of the “Network” page (®page 104).

Operating Instructions 7

1 Monitor images on a PC

3. Press the [Enter] key on the keyboard.

→ The window with the user name and password entry fields will be displayed.

4. Enter the user name and the password.

The default user name and password are as follows. User name: admin Password: 12345

8 Operating Instructions

5. Click the [OK] button.

VT164W

VT164

VP104W

VP104

VP101

→ The “Live” page will be displayed. Refer to

: page 15 for further information about the “Live” page.

1 Monitor images on a PC

: page 10,

When “Off” is selected for “User auth.”, the authentication window will not be displayed before displaying live images. However, when the [Setup] button is clicked, an authentication window is displayed. A user name and password must be entered. The default user name and password are as follows. User name: admin Password: 12345

IMPORTANT

• To enhance the security, change the password for the user name “admin”. It is recommended to change

this password periodically.

• When displaying multiple H.264 images on a PC, images may not be displayed depending on the

performance of the PC.

Note

• The maximum number of concurrent access user is 14 including users who is receiving H.264 images

and users who are receiving JPEG images. Depending on the set values for “Bandwidth control(bit rate)” and “Max bit rate (per client)*”, the maximum concurrent access number may be 14 or less users. When 14 users are concurrently accessing, the access limit message will be displayed for users who subsequently attempt to access. When “Multicast” is selected for “Transmission type” of “H.264”, only the first user who accessed to monitor H.264 images will be included in the maximum number. The second and subsequent users who are monitoring H.264 images will not be included in the maximum number.

• Regardless of whether “On” or “Off” is selected for “H.264 transmission”, the first images displayed are

JPEG images.

• The refresh interval may become longer depending on a network environment, PC performance,

photographic subject, access traffic, etc.

When “H.264 transmission” is operating: max. 5 fps When “H.264 transmission” is not operating (or stopped): max. 30 fps

Operating Instructions 9

OQR

1 Monitor images on a PC

1.2 About the “Live” page (BL-VT164W/BL-VT164)

[select language] pull-down menu

The camera’s display language can be selected. The default language can be set in the [Language] in the [Basic] settings. (®page 39)

[Setup] button

Displays the setup menu. The button will turn green and the setup menu will be displayed.

[Live] button

Display the “Live” page. The button will turn green and the “Live” page will be displayed.

[Multi-screen] buttons

Images from multiple cameras can be displayed on a multi-screen by registering cameras on the setup menu. (®page 18)

[Compression] buttons

• [H.264] button: The letters “H.264” on the button will turn green and an H.264 image will be displayed.

When “On” is selected for “H.264 transmission” of “H.264(1)”, “H.264(2)”, the [H.264] button will be displayed. (®page 51)

• [JPEG] button: The letters “JPEG” on the button will turn green and JPEG image will be displayed.

[Stream] buttons

These buttons will be displayed only when an H.264 image is displayed.

• [1] button: The letter “1” will turn green and images in the main area will be displayed in accordance

with the setting of “H.264(1)”. (®page 51)

• [2] button: The letter “2” will turn green and images in the main area will be displayed in accordance

with the setting of “H.264(2)”. (®page 51)

[Image capture size] buttons

These buttons will be displayed only when a JPEG image is displayed.

10 Operating Instructions

1 Monitor images on a PC

[VGA] The letters “VGA” will turn green and images in the main area will be displayed

in VGA size.

[QVGA] The letters “QVGA” will turn green and images in the main area will be displayed

in QVGA size.

[640x360] The letters “640x360” will turn green and images in the main area will be

displayed in 640 x 360 (pixels).

[320x180] The letters “320x180” will turn green and images in the main area will be

displayed in 320 x 180 (pixels).

[800x600] The letters “800x600” will turn green and images in the main area will be

displayed in 800 x 600 (pixels).

[1280x720] The letters “1280x720” will turn green and images in the main area will be

displayed in 1280 x 720 (pixels).

Note

• When “1280x720” is selected for the image capture size, it may become smaller than the actual

size depending on the window size of the web browser.

• The buttons [VGA], [QVGA] and [800x600] are displayed only when “4:3” is selected for “Aspect

ratio”.

• The buttons [640x360], [320x180], and [1280x720] are displayed only when “16:9” is selected for

“Aspect ratio”.

[Image quality] buttons

These buttons will be displayed only when a JPEG image is displayed.

• [1] button: Images in the main area will be displayed in accordance with the setting for “Quality1” of

“Image quality setting”. (®page 47)

• [2] button: Images in the main area will be displayed in accordance with the setting for “Quality2” of

“Image quality setting”. (®page 47)

[AUX] buttons

These buttons will be displayed only when “AUX output” is selected for “Terminal 3” of “Alarm” on the setup menu. (®page 77)

• [Open] button: The letters “Open” on the button will turn green and the status of AUX connector will

be open.

• [Close] button: The letters “Close” on the button will turn green and the status of the AUX connector

will be closed.

Note

• The names of “AUX”, “Open” and “Close” can be changed. (®page 83)

[Zoom] buttons

• : Click this button to adjust the zoom ratio to the “Wide” side.

• : Click this button to set the zoom ratio to x1.0.

• : Click this button to adjust the zoom ratio to the “Tele” side.

[Auto mode]

Select an operation from the pull-down menu and click the [Start] button. The selected operation will start. Click the [Stop] button to stop the operation. The selected operation will stop when the camera (panning/tilting/zooming) is operated or when an action that is to be taken according to the settings for “Self return” (®page 55) or for “Camera action on alarm” (®page 79) starts.

Operating Instructions 11

1 Monitor images on a PC

• Preset map-shot: Eight thumbnail images of the preset position 1-8 (®page 65) will be displayed

orderly on a newly displayed window. When a thumbnail image is clicked, the camera moves to the respective position and live images will be displayed on the “Live” page.

Note

• Do not operate the browser until all the thumbnail images are displayed and the camera returns to

the original position (where the camera was when “360 map-shot” or “Preset map-shot” was carried out).

• When “Preset map-shot” is carried out with an unregistered preset position (among preset position

1-8), the thumbnail image of the preset position before the unregistered preset position will be displayed. In this case, the camera will not move when the thumbnail image is clicked.

• The camera will not always return to the exactly same position where it was before “Preset

map-shot” was carried out. (It may sometimes be slightly different.)

• The window on which the thumbnail images are displayed will close when clicking the following

buttons that can switch the camera channel or reload images: [Live], [Multi-screen], [H.264], [JPEG], [Stream], [Image capture size], [Image quality], [Setup]. To display the thumbnail images again, carry out “Preset map-shot” again.

Control pad/buttons

• : Left-click on the control pad to adjust the horizontal/vertical position of the camera

(panning/tilting). Panning/tilting speed will be faster if a clicked point gets farther from the center point of the control pad. It is also possible to pan/tilt the camera by dragging the mouse. Zoom can be adjusted by right-clicking. When an upper/lower area of the control pad is right-clicked, the displayed image will be zoomed in/out on. Zoom can also be adjusted using the mouse wheel.

[Brightness] buttons

Available range: 0 - 127

•

button: The displayed image will be darker.

• button: The adjusted brightness will return to the default brightness (64).

• button: Image will be brighter.

[Preset]

Select a preset position from the pull-down menu and click the [Go] button. The camera will move to the selected preset position (®page 65). “H” next to the preset position number indicates the home position. When “Home position” is selected, the camera will move to the home position. (®page 55) When “Preset ID” is registered for a preset position, the registered preset ID will be displayed next to the preset position number.

Camera title

The camera title entered for “Camera title” on the [Basic] page will be displayed. (®page 39)

Alarm occurrence indication button

This button will be displayed and will blink when an alarm has occurred. When this button is clicked, the alarm output terminal will be reset and this button will disappear. (®page 30)

Full screen button

Images will be displayed on a full screen. To return to the “Live” page, press the [Esc] key. The aspect ratio of displayed images will be adjusted in accordance with the monitor.

12 Operating Instructions

1 Monitor images on a PC

Snap shot button

Click this button to take a picture (a still picture). The picture will be displayed on a newly opened window. When right-clicking on the displayed image, the pop-up menu will be displayed. It is possible to save the image on the PC by selecting “Save” from the displayed pop-up menu. When “Print” is selected, printer output is enabled.

Note

• The following setting may be necessary when using Windows 7 or Windows Vista.

Click “Internet Options” on the Tools menu of Internet Explorer, and then click the [Security] tab. Select “Trusted Sites”, and click “Sites”. Register the camera address on the “Website” in the “Trusted Sites” window.

Mic input button

Turns on/off the audio reception (hear audio from the camera on a PC). This button will be displayed only when “Mic input”, “Interactive(Full-duplex)” or “Interactive(Half-duplex)” is selected for “Audio transmission/ reception” on the setup menu. (®page 72)

When this button is clicked, the button will turn into the button and audio from the camera will not be heard. Audio volume can be adjusted (Low/ Middle/ High) by moving the volume cursor .

Audio output button

Turns on/off the audio transmission (play audio from the PC on the unit speaker). This button will be displayed only when “Audio output”, “Interactive(Full-duplex)” or “Interactive(Half-duplex)” is selected for “Audio transmission/reception” on the setup menu. (®page 72) The button will blink during the audio transmission.

When this button is clicked, the button will turn into the

button and audio from the PC will not be heard.

Audio output volume can be adjusted (Low/Middle/High) by moving the volume cursor .

Note

• When a user is using the audio transmission function with “Interactive(Half-duplex)” selected, the

receiver button and the transmission button will be inoperable for the other users. When “Interactive(Full-duplex)” is selected, the transmission button is inoperable for other users.

• Possible duration of audio transmission is up to 5 minutes per transmission. When 5 minutes have

passed, the audio transmission will automatically stop. To turn the audio transmission function on, click the [Audio output] button again.

• When the camera is restarted, the adjusted volume level (for both the audio transmission and

reception) will return to the level that had been set on the [Audio] tab on the setup menu. (®page 72)

• Actual volume level will change in three steps even though the volume cursor can be adjusted

minutely.

Main area

Images from the camera will be displayed in this area. The current time and date will be displayed according to the settings configured for “Time display format” and “Date/time display format”. (®page 40) In addition, when being adjusted, the status of brightness (®page 41), panning/tilting degree and the zoom ratio display (®page 56), and the preset ID (®page 67) will be displayed as well as the characters configured for “Camera title on screen” (®page 40). The number of lines for the display is 2. Click a desired point in the main area on the “Live” page that is to be the center of the angle of view. The camera moves to adjust the position in order to set the clicked point as the center. When selecting an area in the main area by dragging the mouse, the selected area will be located at the center of the main area. In this case, the zoom ratio will be adjusted automatically. Zoom can be adjusted using the mouse wheel.

Operating Instructions 13

1 Monitor images on a PC

Note

• When operated by a lower access level user, images displayed on the screen may be changed

temporarily. This does not affect operation of the camera.

• When the mouse is dragged to move the camera beyond its operable range, the camera will move to

the requested direction and will stop at the end of the operable range. Then, the zoom ratio of the displayed image will automatically be adjusted.

• Depending on the PC in use, screen tearing* may occur when the shooting scene drastically changes

due to the GDI restrictions of the OS. *A phenomenon in which portions of the screen are displayed out of alignment.

Only operable by users whose access level is “1. Administrator”.

Only operable by users whose access level is “1. Administrator” or “2. Camera control” when “On” is selected for “User auth.” (®page 94)

Operable by users who belong to the access level selected for “Permission level of audio trans./recep.” on the [Audio] tab of the “Image/Audio” page. Refer to page 72 for further information about the “Permission level of audio trans./recep.”.

14 Operating Instructions

KLNM

1 Monitor images on a PC

1.3 About the “Live” page (BL-VP104W/BL-VP104/

BL-VP101)

[select language] pull-down menu

The camera’s display language can be selected. The default language can be set in the [Language] in the [Basic] settings. (®page 39)

[Setup] button

Displays the setup menu. The button will turn green and the setup menu will be displayed.

[Live] button

Display the “Live” page. The button will turn green and the “Live” page will be displayed.

[Multi-screen] buttons

Images from multiple cameras can be displayed on a multi-screen by registering cameras on the setup menu. (®page 18)

[Compression] buttons

• [H.264] button: The letters “H.264” on the button will turn green and an H.264 image will be displayed.

When “On” is selected for “H.264 transmission” of “H.264(1)”, “H.264(2)”, the [H.264] button will be displayed. (®page 51)

• [JPEG] button: The letters “JPEG” on the button will turn green and JPEG image will be displayed.

[Stream] buttons

These buttons will be displayed only when an H.264 image is displayed.

• [1] button: The letter “1” will turn green and images in the main area will be displayed in accordance

with the setting of “H.264(1)”. (®page 51)

• [2] button: The letter “2” will turn green and images in the main area will be displayed in accordance

with the setting of “H.264(2)”. (®page 51)

[Image capture size] buttons

These buttons will be displayed only when a JPEG image is displayed.

[VGA] The letters “VGA” will turn green and images in the main area will be displayed

in VGA size.

Operating Instructions 15

VP104W

VP104

VP104W

VP104

VP104W

VP104

1 Monitor images on a PC

[QVGA] The letters “QVGA” will turn green and images in the main area will be displayed

[640x360] The letters “640x360” will turn green and images in the main area will be

[320x180] The letters “320x180” will turn green and images in the main area will be

in QVGA size.

displayed in 640 x 360 (pixels).

displayed in 320 x 180 (pixels).

[800x600]

[1280x720]

The letters “800x600” will turn green and images in the main area will be displayed in 800 x 600 (pixels).

The letters “1280x720” will turn green and images in the main area will be displayed in 1280 x 720 (pixels).

Note

• The buttons [VGA], [QVGA] and [800x600] are displayed only when “4:3” is selected for “Aspect

ratio”.

• The buttons [640x360], [320x180], and [1280x720] are displayed only when “16:9” is selected for

“Aspect ratio”.

• When “1280x720” is selected for the image capture size, it may become smaller than the actual

size depending on the window size of the web browser.

[Image quality] buttons

These buttons will be displayed only when a JPEG image is displayed.

• [1] button: Images in the main area will be displayed in accordance with the setting for “Quality1” of

“Image quality setting”. (®page 47)

• [2] button: Images in the main area will be displayed in accordance with the setting for “Quality2” of

“Image quality setting”. (®page 47)

[Zoom] buttons

Images will be zoomed in on with the electronic zoom by the viewer software “Network Camera View 4S”.

• [x1] button: The letter “x1” will turn green and images in the main area will be displayed at x1.

• [x2] button: The letter “x2” will turn green and images in the main area will be displayed at x2.

• [x4] button: The letter “x4” will turn green and images in the main area will be displayed at x4.

[Brightness] buttons

Available range: 0 - 127

•

button: The displayed image will be darker.

• button: The adjusted brightness will return to the default brightness (64).

• button: Image will be brighter.

Camera title

The camera title entered for “Camera title” on the [Basic] page will be displayed. (®page 39)

Alarm occurrence indication button

This button will be displayed and will blink when an alarm has occurred. When this button is clicked, the alarm output terminal will be reset and this button will disappear. (®page 30)

Full screen button

Images will be displayed on a full screen. To return to the “Live” page, press the [Esc] key. The aspect ratio of displayed images will be adjusted in accordance with the monitor.

Snap shot button

16 Operating Instructions

1 Monitor images on a PC

Note

• The following setting may be necessary when using Windows 7 or Windows Vista.

Main area

Note

• When operated by a lower access level user, images displayed on the screen may be changed

temporarily. This does not affect operation of the camera.

• When the mouse is dragged to move the camera beyond its operable range, the camera will move to

the requested direction and will stop at the end of the operable range. Then, the zoom ratio of the displayed image will automatically be adjusted.

• Depending on the PC in use, screen tearing* may occur when the shooting scene drastically changes

due to the GDI restrictions of the OS. *A phenomenon in which portions of the screen are displayed out of alignment.

Only operable by users whose access level is “1. Administrator”.

Only operable by users whose access level is “1. Administrator” or “2. Camera control” when “On” is selected for “User auth.” (®page 94)

Operating Instructions 17

1 Monitor images on a PC

1.4 Monitor images from multiple cameras

Images from multiple cameras can be displayed on a multi-screen. Images from 4 cameras (up to 16 cameras) can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in advance. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered. (®page 75)

IMPORTANT

• When displaying images on a 16-screen, panning, tilting and zooming operations become unavailable

for images from cameras with Pan/Tilt/Zoom functions.

• When displaying images on a 4-screen, panning, tilting and zooming operations become available only

for images from cameras with Pan/Tilt/Zoom functions. Refer to the [Readme] file on the provided CD-ROM for further information about the compatible cameras and their versions. Or refer to our website (http://panasonic.net/pss/security/support/info.html).

• Only JPEG images with frame by frame playback can be displayed on a multi-screen. Audio will not

be heard.

• When the power is turned off or the LAN cable is disconnected while displaying images, displaying

images on a multi-screen from the “Live” page will become unavailable.

• When displaying the image on a multi-screen and “16:9” is selected for “Aspect ratio”, the image will

be displayed altered vertically to the aspect ratio of “4:3”.

• “Network Camera Recorder with Viewer Software Lite” which supports live monitoring and recording

images from multiple cameras is available. For further information, refer to our website (http://panasonic.net/pss/security/support/info.html).

1. Click the desired [Multi-screen] on the “Live” page.

→ Images from the registered cameras will be displayed on a selected multi-screen (screen can be split

up to 16 areas). The following are instructions when displaying on a 4-split screen.

To show 1 camera screen, click the [Live] button. You can also click “1” below “Multi-screen” to display the camera's “Live” page.

Click the [Multi-screen] button to display images from cameras in a multi-screen of 4 to 16 screens. Click a camera title. Live images from the camera corresponding to the clicked camera title will be

displayed on the “Live” page of the newly opened window.

18 Operating Instructions

2 Monitor images on a cellular phone/mobile terminal

2.1 Monitor images on a cellular phone

It is possible to connect to the camera using a cellular phone via the Internet and monitor images (JPEG only) from the camera on the screen of the cellular phone. It is also possible to refresh images to display the latest image or perform panning, tilting and zooming operations.

IMPORTANT

• When the authentication window is displayed, enter the user name and password. The default user

name and password are as follows. User name: admin Password: 12345 To enhance the security, change the password for the user “admin”. (®page 94)

• If the cellular phone in use is not compatible with UTF-8 encode, it is impossible to display the screen

correctly.

Note

• It is necessary to configure the network settings of the cellular phone in advance to connect to the

Internet and monitor images from the camera. (®page 104)

Operating Instructions 19

A B C

D E F

H I

2 Monitor images on a cellular phone/mobile terminal

1. Access to “http://IP address/mobile”

cellular phone.

→ Images from the camera will be displayed.

or “http://Host name registered in the DDNS server/mobile” using a

20 Operating Instructions

VT164W

VT164

VT164W

VT164

VT164W

VT164

VT164W

VT164

VT164W

VT164

VT164W

VT164

VT164W

VT164

2 Monitor images on a cellular phone/mobile terminal

Functions Outline of functions

A Pan/tilt

B Zooming control

Controls the camera direction. The camera will pan or tilt to each direction by pressing the corresponding dial key.

It is possible to perform zooming operations of the camera by pressing “*” or “#”.

C Refresh Refreshes the camera images by pressing the dial key “5”.

D Resolution control Changes the image capture size by pressing the dial key “0”.

• Image in the aspect ratio of “4:3”

Changes the image capture size between 320x240 (default) and 640x480.

• Image in the aspect ratio of

“16:9”

Changes the image capture size between 320x180 (default) and 640x360.

Note

• Some cellular phones cannot change the image capture size even

when resolution is changed by resolution control.

E Image quality control

F Home position

G Preset

H AUX control

It is possible to change the image quality between “Quality1” and “Quality2”. (®page 47)

The camera will move to the home position (®page 55). Home position will be displayed only when home position is set.

The camera will move to the designated preset position to display images by pressing the dial key corresponding to the desired channel. (The dial key numbers are not displayed for Preset No 5 or greater. Only preset IDs will be displayed for them.) (®page 65)

Controls the AUX terminal. These buttons will be displayed only when “AUX output” is selected for “Terminal 3” on the setup menu. (®page 77)

I Privacy Mode

J Disable Privacy

Mode

Select “Privacy Mode” to activate Privacy mode.

Select “Disable Privacy Mode” to return to the normal display.

Operating Instructions 21

2 Monitor images on a cellular phone/mobile terminal

Note

• When the HTTP port number is changed from “80”, enter “http://IP address: (colon) + port number/

mobile”*1 in the address box of the browser. When using the DDNS function, access to “http://Host name registered in the DDNS server: (colon) + port number/mobile”.

• When “HTTPS” is selected for “HTTPS” - “Connection” on the [Network] tab of the “Network” page,

enter as follows. “https://IP address: (colon) + port number/mobile” or “https://Host name registered in the DDNS server: (colon) + port number/mobile”

• When the authentication window is displayed, enter the user name of an administrator or user and

password. Depending on the cellular phone in use, password entry may be required each time the screen is switched.

• It is impossible to transmit/receive audio using a cellular phone.

• Depending on the cellular phone in use, larger size images may not be displayed. In this case, selecting

“9 Low” for “Image quality setting” of “JPEG” (®page 47) may sometimes solve this problem.

• Depending on the cellular phone in use or its contract plan, it may be impossible to access.

IP address is the global WAN IP address of the router that can be accessed via the Internet.

Only displayed for users whose access level is “1. Administrator” or “2. Camera control” when “On” is selected for “User auth.”. (®page 94)

2.2 Monitor images on a mobile terminal

It is possible to connect to the camera using a mobile terminal and monitor images (MJPEG only) from the camera on the screen of the mobile terminal. Images are automatically refreshed to display the latest image. Operations such as pan/tilt/zoom can also be performed. The compatible mobile terminals are shown as follows. (As of January, 2012)

– iPad, iPhone, iPod touch (iOS 4.2.1 or later) – Android™ mobile terminals

Only JPEG images can be viewed from standard Android mobile terminal browsers. For further information about compatible devices, refer to our website (http://panasonic.net/pss/security/support/info.html).

IMPORTANT

• When the authentication window is displayed, enter the user name and password. The default user

name and password are as follows. User name: admin Password: 12345 To enhance the security, change the password for the user “admin”. (®page 94)

Note

• To view the camera images from a mobile terminal, network settings needed in order to connect to the

Internet must be set in advance. (®page 104)

22 Operating Instructions

2 Monitor images on a cellular phone/mobile terminal

1. Access to “http://IP address/cam”

or “http://Host name registered in the DDNS server/cam”*2 using a

mobile terminal.

→ Images from the camera will be displayed.

Live images area Displays images from the camera.

Operation buttons area When functions are selected in the function selection area D, buttons to operate those functions are displayed.

Zoom operation area Buttons to operate the zoom are displayed.

Function selection area When functions that can be operated are selected, operation buttons are displayed in the operation buttons area B.

Operating Instructions 23

B E

VT164W

VT164

VT164W

VT164

VT164W

VT164

VT164W

VT164

VT164W

VT164

2 Monitor images on a cellular phone/mobile terminal

2. Click the button of the function that you want to operate.

Pan/Tilt Preset Resolution control AUX control Privacy Mode control Zoom display

Each function is explained below.

24 Operating Instructions

VT164W

VT164

VT164W

VT164

2 Monitor images on a cellular phone/mobile terminal

Pan/Tilt Press the button to display the buttons used to operate pan/tilt on the screen. The pan/tilt can be

adjusted in each direction with the

, , , and buttons.

Preset Press the button to display the buttons used to select the preset position on the screen. Camera images are displayed of the registered preset camera directions according to the preset numbers

selected from the buttons.

• Only position numbers 1-4 for the preset positions are displayed.

• Only registered preset positions are displayed. Unregistered preset positions are not displayed.

Operating Instructions 25

VT164W

VT164

VP104W

VP104

VP101

VT164W

VT164

VP104W

VP104

VP101

2 Monitor images on a cellular phone/mobile terminal

Resolution control Press the button to display the buttons used to select the resolution on the screen. The resolution can be changed by selecting a resolution setting from the buttons.

• Image in the aspect ratio of “4:3”

Changes the image capture size between 320x240, 640x480 (default), and 800x600.

Changes the image capture size between 320x240 and 640x480 (default).

• Image in the aspect ratio of “16:9”

Changes the image capture size between 320x180, 640x360 (default), and 1280x720.

Changes the image capture size between 320x180 and 640x360 (default).

26 Operating Instructions

VT164W

VT164

2 Monitor images on a cellular phone/mobile terminal

AUX control Press the button to display the buttons used to operate the AUX output on the screen. The AUX

output terminals can be controlled with the and buttons. This function is only displayed when [Terminal 3] is set to [AUX output] on the settings menu.

(®page 77)

Operating Instructions 27

VT164W

VT164

2 Monitor images on a cellular phone/mobile terminal

Privacy Mode control Press the button to display the buttons used to operate the privacy mode on the screen. The privacy

mode can be enabled and disabled with the

and buttons.

To activate privacy mode, press .

To deactivate privacy mode, press .

28 Operating Instructions

VT164W

VT164

2 Monitor images on a cellular phone/mobile terminal

Zoom display The camera’s zoom can be operated with the , , and buttons.

Note

• You can change the image size displayed on the mobile terminal by accessing the following addresses. – Large display: http://IP address/cam/dl – Medium display: http://IP address/cam/dm – Small display: http://IP address/cam/ds

• When the resolution is changed by the resolution control, the displayed resolution changes but the

image size remains the same.

• When the HTTP port number is changed from “80”, enter “http://IP address: (colon) + port number/

cam”*1 in the address box of the browser. When using the DDNS function, access to “http://Host name registered in the DDNS server: (colon) + port number/cam”*2.

• When “HTTPS” is set in “HTTPS” - “Connection” on the [Network] tab of the “Network” page, enter the

following: “https://IP address: (colon) + port number/cam” or “https://Host name registered in the DDNS server: (colon) + port number/cam”.

• When the authentication window is displayed, enter the user name of an administrator or user and

password. Depending on the mobile terminal in use, password entry may be required each time the screen is switched.

• It is impossible to transmit/receive audio using a mobile terminal.

• Depending on the mobile terminal in use, larger size images may not be displayed. In this case,

selecting “9 Low” for “Image quality setting” of “JPEG” (®page 47) may sometimes solve this problem.

• Depending on the mobile terminal in use or its contract plan, it may be impossible to access.

IP address is the global WAN IP address of the router that can be accessed via the Internet. However, when accessing the same LAN as the camera with a wireless compatible mobile terminal, the IP address is the local IP address.

Only when accessing the camera through the Internet.

Operating Instructions 29

VT164W

VT164

VT164W

VT164

VT164W

VT164

VP104W

VP104

VP101

3 Action at an alarm occurrence

The alarm action (camera action at an alarm occurrence) will be performed when the following alarms occur.

3.1 Alarm type

• Terminal alarm

: When connecting an alarm device such as a sensor to the EXT I/O connectors 1-3 of the camera, the alarm action will be performed when the connected alarm device is activated.

• Body heat sensor

: When a temperature difference is detected in the sensor's detection

area, the alarm action will be performed.

• VMD alarm: When motion is detected in the set VMD area, the alarm action will be performed.

*VMD stands for “Video Motion Detection”.

• Command alarm: When a Panasonic alarm protocol is received from the connected device via a network,

the alarm action will be performed.

3.2 Action at an alarm occurrence

Display the alarm occurrence indication button on the “Live” page

The alarm occurrence indication button will be displayed on the “Live” page at an alarm occurrence. (®

IMPORTANT

• When “Polling(30s)” is selected for “Alarm status update mode” (®page 39), the Alarm occurrence

indication button will be refreshed in 30-second intervals. For this reason, it may take a maximum of 30 seconds until the alarm occurrence indication button is displayed on the “Live” page at an alarm occurrence.

: page 10,

: page 15)

Notify of alarm occurrences to the device connected to the alarm connector

It is possible to output signals from the alarm connector on the rear of the camera and sound the buzzer when an alarm occurs. The settings for the alarm output can be configured in the “Alarm output terminal setup” section of the [Alarm] tab of the “Alarm” page. (®page 77, page 82)

Transmit an image onto a server automatically

An alarm image can be transmitted at an alarm occurrence to the server designated in advance. The settings required to transmit an alarm image to a server can be configured in the “Alarm image” section on the [Alarm] tab of the “Alarm” page (®page 80) and the [FTP] tab (®page 100) of the “Server” page.

Notify of alarm occurrences by E-mail

Alarm E-mail (alarm occurrence notification) can be sent at an alarm occurrence to the E-mail addresses registered in advance. Up to 4 addresses can be registered as recipients of the alarm E-mail. An alarm image (still picture) can be sent with the alarm E-mail as an attached file. The settings for alarm E-mail can be configured in the “E-mail notification” section on the [Notification] tab of the [Alarm] page (®page 87) and the [E-mail] tab of the “Server” page (®page 99).

30 Operating Instructions

+ 150 hidden pages