Ozito HDR-001 User Manual
HAMMER
WHAT’S IN THE BOX
DRILL
710W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 710W
Input: 230-240V ~ 50Hz
Chuck Size: 13mm (1/2”) Keyless
No Load Speed: 0-3,000/min
Impact Rate: 0-48,000bpm
Max Drilling Capacities: Timber 25mm
Steel 13mm
Masonry 13mm
Weight (Tool Only): 1.8kg
ozito.com.au
Hammer Drill
Side Handle
Depth Rod
18 x Drill Bits
HDR-001
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: carbon brushes, depth rod, drill bits etc.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
0616
KNOW YOUR PRODUCT SETUP & PREPARATION
required
drilling depth
HAMMER DRILL
1 Chuck
2 Depth Rod
3 Side Handle
4 Mode Selector
5 Forward/Reverse Lever
6 Speed Selection Dial
7 Variable Speed Trigger
8 Lock-On Button
9 Power Cord
1. SIDE HANDLE & DEPTH ROD
WARNING! ENSURE THE TOOL IS OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING OPERATIONS.
Fitting the Side Handle
The side handle provides additional comfort, control, and guidance for
the hammer drill.
1 Loosen the side handle by
rotating the handle anticlockwise.
2 Slide the side handle onto the
collar mount of the hammer
drill and secure in place by
rotating the handle clockwise.
1 2 3 4 65 7 8 9
ACCESSORIES
10 Wood Drill Bits x 6
(5/6/8mm)
11 Steel Drill Bits x 6
(5/6/8mm)
12 Masonry Drill Bits x 6
(5/6/8mm)
10 11 12
Using the Depth Rod
The depth rod helps to drill to a pre-determined depth.
1 Loosen the side handle by
rotating the handle anticlockwise.
2 Insert or adjust the
depth rod so the
drill bit extends
beyond the end
of the rod to the
desired drilling
depth.
3 Tighten the side handle to
secure the depth rod in this
position.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Loading...