Orion PREMIUM WIDE, 42” FULL HD TFT-LCD MONITOR Installation And User Manual

Installation and User’s Guide

http://www.orionimages.com

All contents of this document may change without prior notice, and actual product appearance may differ
from that depicted herein

Installation and User’s Guide

32” TFT-LCD MONITOR

(SECURITY)

PREMIUM WIDE SERIES LCD MONITOR

2

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg2

* Follow this safety instruction to use the monitor properly and prevent the damages.

* Keep this user’s guide book for later use.

Warning Statements

* This safety instruction has “ Warning” and “ Caution” as below.

WARNING:

If the user does not follow this instruction,
it may cause the serious damage to the user.

CAUTION:

If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.

Never remove the back over and touch
the inside of the monitor. If you need a
service, please contact the service center.

Keep away the monitor from the
direct sunlight and a heating appliance.

Never push objects of any kind into this
product as they may result in a risk of fire
or electric shock.

Connect the power code to the wall
outlet tightly. If the power code or plug are
defective and the wall outlet is not tight,

p

lease do not use them.

3

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg3

Warning Statements

Do not install this monitor on the outside
and near water. If may cause damage to
the product, electric shock and fire.

For cleaning do not use liquid cleaners.
Never touch the power plug with wet­hands.

When lightning and thundering, unplug
the monitor from the wall outlet and never
touch it.

Unplug this product from the wall outlet,
when It does not operate for a long time.

When smoking and noising from the
monitor, unplug the product from the wall
outlet and contact a service center.

How to fix

1. Do not open this product as it contains high voltage inside.

2. It may create an electric shock.

3. It the user disassembles and remove the back cover, it does not make sure

4. To make up for the damages and do a service and exchange the monitor..

4

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg4

Install this monitor some distance
From the wall and do not install unless
Proper ventilation is provided.

Place this product on a stable place.
If not, it may fall, causing serious
Damages to the monitor and people.

The openings must not be blocked by
curtain, rug or other similar surface.

When carrying this monitor, be careful
not to damage the panel and drop it
It may cause some trouble.

Before carrying the monitor, tum it off
and Unplug the signal cables and the
power code From the wall outlet.

Take the power plug out from the wall
outlet. Do not pull the cable. It may
snap the inner wires and cause
overheating and fire.

Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.

Do not press the LCD panel with hands
or the sharpened material hardly.

For cleaning, unplug the monitor from
the Wall outlet. Do net use the liquid
cloth. Use the soft cloth.

Do not use the chemical liquid for
cleaning. It may cause fading and
breakage.

5

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg5

TABLE OF CONTENTS

1. INSTALLATION

.................................................................................................................

1.1 Parts

……....................................................................................................................

2. FEATURES

…..................................................................................................................

2.1 Specifications

…….……..............................................................................................

3. OSD SETTING

..........................................................................................................

6. TROUBLESHOOTING

7. LIMITED LIFETIME WARRANTY

4. CONTROL BUTTON

1.2 Connection

…..…..........................................................................................................

5. INFORMATION TO THE USER

1.3 Remote Controller

..…….............................................................................................

6

9
9

10-14

17
18

15

16

6

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg6

INSTALLATION

1.1 Parts

Remove the package cover and place the product on a flat and secure surface or in the
installation location. Check whether all the following device and accessories are included with
the main system.

7

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg7

INSTALLATION

1. AC INPUT

2. HDMI IN

3. DVI IN

4. RGB IN

5. PC STEREO INPUT

6. COMPONENT IN

7. STEREO AUDIO IN

8. AUDIO2 IN

9. AUDIO1 IN

10. S-VIDEO (Y/C) OUT

11. S-VIDEO (Y/C) IN

12. VIDEO2 OUT

13. VIDEO2 IN

14. VIDEO1 OUT

15. VIDEO1 IN

16. TRIGGER IN

HDMI signal input.

DVI-D signal input.

RGB signal input.

YPbPr signal input.

Component stereo audio signal input.

Stereo audio signal input. This input for VIDEO2.

Stereo audio signal input. This input for VIDEO1 and S-VIDEO.

Y/C separated signal looping output.

Y/C separated signal input.

Video looping output for VIDEO2.

Composite signal input for VIDEO2.

Video looping output for VIDEO1.

Composite signal input for VIDEO1.

Trigger signal input. (NO / NC)

1.2 Connection

8

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg8

INSTALLATION

A. SOURCE SELECT

B. PVM INPUT (Not Available on this Model)

C. PIP MENU

1.3 Remote Controller

Press the button to select the desired input source

POWER

Turn the monitor ON or OFF

MUTE

Temporarily silences the sound

COLOR TEMP

Adjust the color temperature of the screen.

SCAN MODE

Change the scan mode of the screen. (FULL / UNDER / OVER)

MENU/EXIT

Activates and exits the OSD menu

KEY LOCK

Prevent unauthorized operation of the equipment by locking the
buttons

STILL

P. INPUT: Selects an input source for the sub picture

PIP: Activates/deactivates PIP/PBP mode

PIP: Activates/deactivates PIP/PBP mode

P. LOC: Selects a location for the sub picture
P. SIZE: Selects the size of the sub picture
P. SWAP: Swaps the main and sub picture
P. SET: Alternates between main and sub audio input

9

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg9

FEATURES

VIDEO

Screen Size

32”

Pixel Type Active Matrix TFT
Max. Resolution

1366 x 768 @ 60Hz (WSXGA)

Pixel Pitch

0.51 x 0.51mm

Brightness

500 cd/㎡
Contrast Ratio 1500 : 1
Aspect Ratio

16:9
Viewing Angle (H/V)

178 / 178

Display Color 16.7 Million
Response Time < 10ms
Video System NTSC / PAL
Frequency (H) 30 ~ 64KHz
Frequency (V) 56 ~ 75Hz
Panel Lamp Life 50,000hours

MECHANICAL

Packing Dimension

W x H x D

36.6 x 26 x 10.8

Weight

43lbs
Power Consumption

150W
Power Source AC 110~230, 50/60Hz (Auto Switching)

2.1 Specifications (32 Inch)

NOTE : Technical specifications are subject to change without notice..

10

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg10

OSD (On Screen Display) SETTING

B. Input Select

3.1 OSD MENU Description

A. Menu Selection

1. Press the MENU key to access the Main menu.

2. Use the

and arrow key to highlight a selection

3. Press the

/SELECT key to select an item.

4. Use the

and arrow key to highlight a selection.

5. Use the

and arrow key to adjust the setting on a selected item.

NOTE : If you don’t connect RGB port, RGB SETUP menu is not select.

Inputs can be set to VIDEO1, VIDEO2, S-VIDEO, RGB PC, DVI, HDM, COMPONENT mode.

Press the /SELECT key then you can change the input source.

11

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg11

OSD (On Screen Display) SETTING

C. Screen Menu

1. SCAN MODE

2. PIP

3. PIP INPUT

4. PIP SWAP

5. PIP SIZE

6. PIP R/T

Select the screen size of main. (FULL / UNDER / OVER)

Select PIP mode. (OFF / ON / DW1 / DW2)

Select sub input of PIP mode. (VIDEO1 / VIDEO2 / S-VIDEO)

Select swap to interchange main with PIP

Select the PIP size. (SMALL / NORMAL / LARGE)

Select the PIP position.

- R/B : Right Bottom

- L/B : Left Bottom

- R/T : Right Top

- L/T : Left Top

12

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg12

OSD (On Screen Display) SETTING

D. Setup Menu

1. INPUT

2. LANGUAGE

3. SOUND MUTE

4. BUTTON LOCK

5. NOISE REDUCTION

6. OSD TIME

7. DEFAULT

Select input source. (VIDEO1 / VIDEO2 / S-VIDEO / RGB PC / DVI / HDMI / COMPONENT).

Select English, Italian, French, Spanish or German for the OSD display.

Select OFF or ON. ‘ON’ silences the sound, ‘OFF’ return the sound.

Prevents unauthorized operation of the equipment by locking the buttons. Button lock feature by
pressing the

◀ and ▲ buttons for 5 seconds.

Reduces the background noise of the video signal.

Select the OSD display time from 5 seconds to 30 seconds.

Select restore to return to the factory setting.

13

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg13

OSD (On Screen Display) SETTING

E. Trigger Setup Menu

1. TRIGGER MODE

2. TRIGGER INPUT

3. TRIGGER DWELL

Sets the video input witch will be displayed when trigger signal. (OFF/ FULL / DW1 / DW2)

Select the input source of trigger mode. (VIDEO1 / VIDEO2 / S-VIDEO).

Sets the time how long displayed on the screen of trigger mode from 10 seconds to 60 seconds.

14

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg14

OSD (On Screen Display) SETTING

C. Menu Display

15

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg15

CONTROLL BUTTON

Menu/EXIT:

Activates and exits the OSD.

SOURCE/

:

Select input source, and select the OSD menu.

AUTO/

▲:

Move the OSD menu and auto adjustment of RGB source.

◀ (VOL-):

Decrease the level of volume and move the previous
menu.

Turns the power O N or OFF. There will be a few seconds delay
before the display appears.

The power LED(next to the power switch) lights with green when
the power is turned ON.

The power is turned off by pressing the power switch again and
the power LED goes Red.

▶/SELECT:

Increase the level of volume and select the OSD menu.

LED LENS

IR RECEIVE LENSE

16

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg16

INFORMATION TO THE USER

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one more
of the following measures:

The manufacturer is not responsible for any Radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate
the equipment."

z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

z Consult the dealer or an experienced radio / TV technician for help.

WARNING:

17

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg17

TROUBLESHOOTING

* When the following troubles are occurred, follow the trouble shooting. Before contacting a

service center.

Troubleshooting Troubleshooting Tip

1. Make sure if the power supply is connected property

2. Turn on the power.

The screen doesn’t show up

3. Select the input signal right for the connected port.

The screen is too light or to dark

Control the BRIGHTNESS

The screen size is not fit for the PC
signal

Press the AUTO key among keys in the front.
(It is used only in the PC signal)

The screen color shows strange in
the PC signal

In the FUNCTION menu of OSD menu, perform the AUTO­ADJUST.

18

Installation and User’s Guide

http://www.orionimages.com

7300 Bolsa Avenue, Westminster CA 92683 / Tel: [phone] / Fax: [phone]

pg18

2Year Limited Warranty

Contact Orion Images

All Orion Images products carry a limited warranty from ship date against defects in materials
and workmanship. Orion Images is not liable for improper installation that results in damage to
mounts, adapters, display equipment or personal injury.

In the event of missing and/or damage equipment, or technical questions, the
following information can help in the completion of the installation.

Address: 7300 Bolsa Avenue, Westminster, CA 92683
Tel: [phone] / Fax: [phone]
Email: [e-mail]
Website: http://www.orionimages.com