Page 1
EN
1
CONTENTS
Contents ................................................................... 1
Introduction .............................................................. 2
About Oregon Scientific .......................................... 2
Product Overview .................................................... 3
Front View .............................................................. 3
Side View ...............................................................4
Back View .............................................................. 5
Remote Sensor (THGR122NX) ............................. 6
Getting Started ......................................................... 7
Batteries ................................................................. 7
AC Adapter (Main Unit) .......................................... 7
Change Settings .................................................... 7
Table Stand ............................................................ 7
Remote Sensor (THGR122NX) ................................ 8
Setup Sensor ......................................................... 8
Data Transmission ................................................. 9
Search for Sensor ..................................................9
Clock ......................................................................... 9
Turn Atomic Clock ON/OFF .................................10
Set Clock .............................................................10
Switch Clock Display ........................................... 10
Alarm ....................................................................... 10
View Alarm Settings ............................................. 10
Set Alarm ............................................................. 11
Activate Alarm ...................................................... 11
Snooze Alarm ...................................................... 11
Temperature and Humidity .................................... 11
Select Temperature Unit ...................................... 11
Select Sensor Channel ........................................ 11
Minimum / Maximum Records ............................. 12
Temperature and Humidity Trend ........................ 12
Backlight ................................................................. 12
Projector ................................................................. 12
Project Time ......................................................... 12
Rotate Image ....................................................... 12
Focus Image ........................................................ 12
Continuous Projection ......................................... 12
Reset System .......................................................... 13
Safety and Care ...................................................... 13
Warnings .................................................................13
Troubleshooting ..................................................... 14
Specifications .........................................................14
Main Unit Dimensions ..........................................14
Remote Sensor Dimensions ................................ 14
Temperature ......................................................... 14
Relative Humidity .................................................14
Remote Sensor (THGR122NX) ........................... 15
Clock ....................................................................15
Power ................................................................... 15
FCC Statement ....................................................... 15
RMR606HGPA_R5 9/3/04, 4:16 PM1
Page 2
EN
2
INTRODUCTION
Thank you for selecting the Oregon Scientific
TM
Wireless Thermo-Hygrometer & Atomic Alarm Clock with
Projection (RMR606HGPA). This device bundles precise
time keeping, time projection, alarm, and temperature
and humidity monitoring features into a single tool you
can use from the convenience of your home.
In this box, you will find:
• Main unit
• Remote sensor (THGR122NX)
• AC Adapter
Keep this manual handy as you use your new product.
It contains practical step-by-step instructions, as well
as technical specifications and warnings you should
know.
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn
more about Oregon Scientific products such as digital
cameras; MP3 players; children’s electronic learning
products and games; projection clocks; health and
fitness gear; weather stations; and digital and conference
phones. The website also includes contact information
for our customer care department in case you need to
reach us, as well as frequently asked questions and
customer downloads.
We hope you will find all the information you need on
our website, however if you’d like to contact the
Oregon Scientific Customer Care department directly,
please visit:
www2.oregonscientific.com/service/support
OR
Call 949-608-2848 in the US.
For international enquiries, please visit:
http://www2.oregonscientific.com/about/international/
default.asp
RMR606HGPA_R5 9/3/04, 4:16 PM2
Page 3
EN
3
PRODUCT OVERVIEW
FRONT VIEW
1. SNOOZE / LIGHT: Press to activate backlight or
snooze
2. Temperature Area: Readings, trend line, sensor
reception status and channel number
3. Humidity Area: Readings; trend line, and battery
status
4. Clock / Alarm Area: Time, time zone, day of week,
month, date, alarm, and Atomic Clock reception
status
5. Projector: projects the time
1
2
3
4
5
RMR606HGPA_R5 9/3/04, 4:16 PM3
Page 4
EN
4
SIDE VIEW
1.
: Press to increase setting, activate Atomic Clock
signal reception
2.
: Press to decrease setting
3. MODE: Press to change display / settings
4. CHANNEL: Press to switch remote sensor
5. ((.)): Press to view alarm settings, activate alarm
MODE
CHANNEL
1
2
3
4
5
RMR606HGPA_R5 9/3/04, 4:16 PM4
Page 5
EN
5
FOCUS
IMAGE
ROTATI ON
MODEL NO. RMR606HGPA
DC 4.5V
"AA" UM3 1.5V
"AA" UM3 1.5V
RESET
MEM
ZONE C / F
BACK VIEW
1. Projector
2. Focus knob
3. Image rotation knob
4. Projection on/off switch
5. Battery compartment
6. ZONE: Press to switch time zones, deactivate
Atomic Clock signal reception (located in battery
compartment)
7. MEM: Press to view current or saved max / min
temperature readings.
8. °C / °F switch (located in battery compartment)
9. RESET hole (located in battery compartment)
10. Power jack: Insert AC power adapter plug here
11.Table stand
1
2
3
4
5
6789
10
11
RMR606HGPA_R5 9/3/04, 4:16 PM5
Page 6
EN
6
REMOTE SENSOR (THGR122NX)
1. LCD display
2. LED Status indicator
1. Wall mount hole
2. RESET
3. Channel number (1 - 3)
4. Battery compartment
(Battery compartment cover not shown)
1
2
1
2
3
4
RMR606HGPA_R5 9/3/04, 4:16 PM6
Page 7
EN
7
AC ADAPTER (MAIN UNIT)
An AC Adapter is supplied for use with this product. It
must be plugged in for the continuous projection feature
to work. The power jack is located on the back of the
main unit.
CHANGE SETTINGS
1. Press and hold MODE for 2 seconds to enter setting
mode.
2. Press UP or DOWN to change settings.
3. Press MODE to confirm.
TABLE STAND
The table stand is located on the back of the product, as
shown below.
GETTING STARTED
BATTERIES
Batteries are not supplied with this product. You will need
to purchase 2 x UM-3 (AA) 1.5V alkaline batteries for
the main unit, and 2 x UM-4 (AAA) 1.5V alkaline batteries
for the remote sensor.
Insert batteries before first use, matching the polarity as
shown in the battery compartment. For best results,
install batteries in the remote sensor before the main
unit. Press RESET after each battery change.
Do not use rechargeable batteries.
NOTE
shows when batteries are low.
UNIT
LOCATION
Main Humidity Area when the
INDOOR humidity is
shown.
Remote Humidity Area when the
OUTDOOR humidity is
shown.
RMR606HGPA_R5 9/3/04, 4:16 PM7
Page 8
EN
8
REMOTE SENSOR (THGR122NX)
This product is shipped with a THGR122NX Thermo/
Hygro Sensor that collects Temperature and Humidity
data. Data can be collected from up to 3 sensors.
Additional sensors sold separately.
SETUP SENSOR
Open the remote sensor battery compartment with a
small Phillips screwdriver.
1. Insert the batteries, matching the polarity as shown
in the battery compartment.
2. Set the channel. The switch is located in the battery
compartment.
SWITCH OPTION
Channel
Channel 1 - 3. If you are using
more than one sensor, select a
different channel for each sensor.
3. Place the sensor near the main unit. Press RESET
on the sensor to initiate signal sending between the
sensor and the main unit. The reception icon on
the main unit will blink for approximately 3 minutes
while it is searching for the sensor. (Refer to the
Sensor Data Transmission section for more
information.)
4. Close the remote sensor battery compartment.
5. Secure the sensor in the desired location using the
wall mount or table stand.
For best results:
• Insert the batteries and select the channel and
temperature unit before you mount the sensor.
• Place the sensor out of direct sunlight and
moisture.
• Do not place the sensor more than 30 meters
(98 feet) from the main (indoor) unit.
• Position the sensor so that it faces the main
(indoor) unit, minimizing obstructions such as
doors, walls, and furniture.
• Place the sensor in a location with a clear view
to the sky, away from metallic or electronic
objects.
• Position the sensor close to the main unit during
cold winter months as below-freezing
temperatures may affect battery performance and
signal transmission.
You may need to experiment with various locations to
get the best results.
Standard Alkaline batteries contain signifcant amounts
of water. Because of this they will freeze in low
temperatures of approximately 10°F. Disposable Lithium
batteries have a much lower threshold for temperature
with an estimated freezing range of below -40°F. The
Liquid Crystal Display in outdoor thermometers will
remain operational to -20°F with adequate power.
RMR606HGPA_R5 9/3/04, 4:16 PM8
Page 9
EN
9
--- shows in Temp /
Humidity Areas
ICON
DESCRIPTION
Main unit is searching for
sensors.
At least 1 channel has
been found.
Channel 1 is selected (number
will change depending on the
sensor you select)
The selected sensor cannot
be found. Search for the
sensor or check batteries.
SEARCH FOR SENSOR
To search for a sensor, press and hold MEM and
CHANNEL for 2 seconds.
If the sensor is still not found, check the batteries,
obstructions, and remote unit location.
Signals from household devices such as
doorbells, electronic garage doors, and home security
systems may cause temporary reception failure. This is
normal and does not affect general product performance.
The reception will resume once the interference ends.
CLOCK
This product shows the current time, time zone, and day
of week in English, Spanish, or French. The time is
automatically updated by the US Atomic Clock in
Boulder, Colorado unless you disable this feature.
Signals are collected by the main unit when it is within
1500 km (932 miles) of a signal.
Initial reception takes 2 - 10 minutes, and is initiated
when you first setup the unit, and whenever you press
RESET. Once complete, the reception icon will stop
blinking. The icon is shown in the Clock Area.
Wireless ranges can be impacted by a variety of factors
such as extremely cold temperatures. Extreme cold may
temporarily reduce the effective range between the
sensor and the base station.
If the unit’s performance fails due to low temperature,
the unit will resume proper functioning as the
temperature rises to within the normal temperature range
(i.e no permanent damage will occur to the unit due to
low temperatures).
DATA TRANSMISSION
Data is sent from the sensor(s) every 40 seconds.
The reception icon shown in the Temperature and
Humidity Areas shows the status.
NOTE
NOTE
RMR606HGPA_R5 9/3/04, 4:16 PM9
Page 10
EN
10
To force a manual search for Atomic Clock signals, press
and hold UP for 2 seconds. If no signal is found, check
the batteries.
TURN ATOMIC CLOCK ON/OFF
Perform this step if you cannot receive Atomic Clock
signals. Press and hold ZONE (located in the battery
compartment) for 2 seconds. Then, manually set the
clock following the “Set Clock” instructions (below).
SET CLOCK
You only need to do this if you have disabled the Atomic
Clock feature (for example, if you are too far from or
cannot receive a signal).
1. Open the battery compartment.
2. Press ZONE repeatedly to display the desired Time
Zone: (P) Pacific, (M) Mountain, (C) Central, or
(E) Eastern.
The signal icon indicates that the Atomic Clock
feature is ON. No icon means that it is OFF
3. Close the battery compartment.
4. Press and hold MODE for 2 seconds. The Clock
Area will blink.
5. Select the hour, minute, year, month, day and
language. Press UP or DOWN to change the
setting. Press MODE to confirm.
The language options are (E) English,
(F) French, and (S) Spanish.
SWITCH CLOCK DISPLAY
Press MODE to toggle between Clock with Seconds,
Clock with Weekday, and Calendar display.
ALARM
This product is equipped with a 2-minute crescendo alarm
and 8-minute snooze.
VIEW ALARM SETTINGS
Press ((.)). The Alarm Time and On/Off status will show
in the Clock Area.
NOTE
RMR606HGPA_R5 9/3/04, 4:16 PM10
Page 11
EN
11
NOTE
SET ALARM
1. Press ((.)).
2. Press and hold ((.)) again for 2 seconds. The Alarm
settings will blink.
3. Select the hour and minute. Press UP or DOWN to
change settings. Press ((.)) to confirm.
ACTIVATE ALARM
Press
((.))
to activate or deactivate the Alarm. shows
in the Clock Area when the Alarm is activated.
SNOOZE ALARM
Press SNOOZE/LIGHT to silence the Alarm for
8 minutes.
If no button is pressed, the Alarm will automatically
silence after 2 minutes. It will then sound again after
8 minutes.
TEMPERATURE AND HUMIDITY
This product can display the following temperature and
humidity information:
• Current, minimum and maximum readings
• Trend line
Data is collected by the remote sensors and displayed
every 40 seconds.
SELECT TEMPERATURE UNIT
Slide the °C / °F switch into the desired location. The
switch is located in the battery compartment. The setting
for the main unit overrides the remote sensor setting.
SELECT SENSOR CHANNEL
Press CHANNEL to switch between sensors 1 - 3.
The icon shows the selected sensor.
To auto-scan between sensors, press and hold
CHANNEL for 2 seconds. Each sensor's data will be
displayed for 3 seconds. To end auto-scan, press
CHANNEL or MEM.
If you use a sensor that collects only
temperature data, humidity will not be shown.
Indoor
Display
Display
Remote
Display
Channel 1
Kineticwave
Icon
Remote
Display
Channel 2
Remote
Display
Channel 3
RMR606HGPA_R5 9/3/04, 4:16 PM11
Page 12
EN
12
MINIMUM / MAXIMUM RECORDS
Press MEM to toggle between current, maximum (MAX)
and minimum (MIN) records for the selected sensor. To
clear the records, press and hold MEM for 2 seconds.
A beep will sound to confirm that the memory has been
cleared.
TEMPERATURE AND HUMIDITY TREND
The trend lines are shown next to the Temperature and
Humidity readings.
PROJECTOR
This product has a built-in projector for viewing the time.
The maximum projection range is 2 meters
(6 feet). The image gets larger the farther you display it.
PROJECT TIME
In a darkened room, press SNOOZE/LIGHT to display
the time for 5 seconds.
ROTATE IMAGE
The ROTATION switch is located on the back of the
projector. Rotate to adjust.
FOCUS IMAGE
The FOCUS switch is located on the back of the
projector. Rotate to adjust.
CONTINUOUS PROJECTION
The AC power adapter must be plugged in to use this
feature (
7).
Slide the Projection ON / OFF button (located on the
side of the projector) to the ON position to use this
feature.
Rising SteadyTrend Falling
ICON
NOTE
BACKLIGHT
Press SNOOZE/LIGHT to activate the backlight for
5 seconds.
RMR606HGPA_R5 9/3/04, 4:16 PM12
Page 13
EN
13
RESET SYSTEM
The RESET buttons are located in the battery
compartments for the main unit and sensors. Press
RESET when you change the batteries and whenever
performance is not behaving as expected (for example,
unable to establish radio frequency link with remote
sensor or radio-controlled clock).
When you press RESET, all settings will return
to default value, and you will lose all stored information.
SAFETY AND CARE
Clean the product with a slightly damp cloth and alcoholfree mild detergent. Avoid dropping the product or placing
it in a high-traffic location.
WARNINGS
This product is designed to give you years of service if
handled properly. Observe the following guidelines:
• Never immerse the product in water. This can
cause electrical shock and damage the product.
• Do not subject the main unit to extreme force,
shock, or fluctuations in temperature or humidity.
• Do not tamper with the internal components.
• Do not mix new and old batteries or batteries of
different types.
• Do not use rechargeable batteries with this
product.
• Remove the batteries if storing this product for a
long period of time.
• Do not scratch the LCD display.
Do not make any changes or modifications to this
product. Unauthorized changes may void your right to
use the product. The technical specification of this
product and contents of this user guide are subject to
change without notice. Images not drawn to scale.
NOTE
RMR606HGPA_R5 9/3/04, 4:16 PM13
Page 14
EN
14
SPECIFICATIONS
MAIN UNIT DIMENSIONS
L x W x H 167 x 52 x 94 mm
(6.57 x 2.05 x 3.70 inches)
Weight 9.31 ounces with battery
REMOTE SENSOR DIMENSIONS
L x W x H 92 x 60 x 20 mm
(3.6 x 2.4 x .79 inches)
Weight 2.22 ounces
without battery
TEMPERATURE
Unit °C or °F
Indoor Range -5 °C to 50 °C
(23 °F to 122 °F)
Outdoor Range -30 °C to 60 °C
(-22 °F to 140 °F)
Resolution 0.1 °C (0.2 °F)
Memory Min / Max
RELATIVE HUMIDITY
Range 25% to 95%
Resolution 1%
Memory Min / Max
TROUBLESHOOTING
Check here before contacting our customer service
department.
Cannot autosynch
1. Adjust batteries.
(
7)
2. Press RESET
(
13)
3. Manually activate
Atomic Clock
feature (
10)
Temp
Shows “LLL”
or “HHH”
Temperature is out-ofrange
Data does
not match
main unit
Initiate a manual sensor
search (
9)
Cannot
change
channel
Check sensors. Only
one sensor is working
(
8)
Check batteries ( 7)
Check location (
8)
Remote
sensor
Cannot locate
remote
sensor
Problem Symptom Remedy
Calendar
Strange date /
month
Change language
(
10)
Clock
Cannot adjust
clock
Disable Atomic Clock
(
10)
RMR606HGPA_R5 9/3/04, 4:16 PM14
Page 15
EN
15
REMOTE SENSOR (THGR122NX)
RF frequency 433 MHz
Range 30 meters (98 feet)
with no obstructions
Transmission every 40 seconds
Channel No. 1 - 3
CLOCK
Atomic Clock Auto or manual
(disabled)
Clock display HH:MM:SS
Hour format 12hr AM/PM
Time zone Pacific (P), Mountain (M),
Central (C), or Eastern (E)
Calendar MM/DD; weekday in
3 languages (E, F, S)
Alarm 2- minute crescendo
Projector 5 second; continuous
POWER
Main unit 2 x UM-3 (AA) 1.5V
alkaline batteries;
4.5V AC/DC Adapter
Sensor 2 x UM-4 (AAA) 1.5V
alkaline batteries
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Warning: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
RMR606HGPA_R5 9/3/04, 4:16 PM15
Page 16
EN
16
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
DECLARATION OF CONFORMITY
The information below is not to be used as contact for
support or sales. Please call our customer service number
(listed on our website at
www.oregonscientific.com, or on
the warranty card for this product) for all inquiries instead.
We
Name: Oregon Scientific, Inc.
Address: 19861 SW 95
th
Place,
Tualatin, Oregon 97062 USA
Telephone No.: 1-800-853-8883
Fax No.: 1-503-684-8883
declare that the product
Product No.: RMR606HGPA
Product Name: Thermo-Hygro Projection Clock
Manufacturer: IDT Technology Limited
Address: Block C, 9/F, Kaiser Estate,
Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon,
Hong Kong
is in conformity with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1) This device may not cause harmful
interference.
2) This device must accept any interference
received, including interference that may
cause undesired operation.
RMR606HGPA_R5 9/3/04, 4:16 PM16
Loading...