Opticon OPH-5000i Specification Manual

OPH-5000i

1st

1

OPH-5000i

Handy Terminal with Bluetooth

This manual provides specifications for the OPH-5000i Wireless

LAN Handy Terminal with imager scanner.

1st

OPH-5000i

1st

2

The information in this document is subject to change without notice.

Document History

Model Number: OPH-5000i Specification Number: SS16051
Edition: 1st Original Spec Number: (SS16003)
Date: 01-September-2016

2016 Copyright Opticon. All rights reserved.

This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted
to any electronic or machine readable form without prior written consent of Opticon.

Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING

OR USING THE PRODUCT.
Serial Number

A serial number appears on all Opticon products. This official registration number is directly related to
the device purchased. Do not remove the serial number from your Opticon device. Removing the
serial number voids the warranty.

Warranty

Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in
materials and workmanship for two years after purchase excluding batteries. Opticon will repair or, at
its option, replace products that are defective in materials or workmanship with proper use during the
warranty period. Opticon is not liable for damages caused by modifications made by a customer. In
such cases, standard repair charges will apply. If a product is returned under warranty and no defect is
found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect,
consequential or incidental damages arising out of use or inability to use both the hardware and
software, even if Opticon has been informed about the possibility of such damages.

Packaging

The packing materials are recyclable. We recommend that you save all packing material to use should
you need to transport your data collector or send it for service. Damage caused by improper
packaging during shipment is not covered by the warranty.

Trademarks

Trademarks used are the property of their respective owners.

Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of
OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002.
TEL [phone]; FAX [phone]

SUPPORT

USA Europe

Phone: [phone]
Email: [e-mail] Email: [e-mail]
Web: www.opticonusa.com Web: www.opticon.com

OPH-5000i

1st

3

Revision History

Product Name : OPH-5000i

Edition Date Page Section Description of Changes

1st 2016/09/01 - - -

OPH-5000i

1st

4

Contents

1 Abstract ............................................................................................................................ 6

2 Overview .......................................................................................................................... 6

3 Basic Specifications ....................................................................................................... 7

4 Detailed View ................................................................................................................. 10

5 Electrical Specifications ............................................................................................... 13

5.1 Electrical Specifications .......................................................................................................... 13

5.2 Wireless Charging .................................................................................................................. 13

6 Interface Specifications ................................................................................................ 13

6.1 USB Interface ......................................................................................................................... 13

6.1.1 Connector ....................................................................................................................... 13

6.1.2 USB Interface Circuit ...................................................................................................... 13

6.2 Bluetooth ................................................................................................................................ 14

6.3 Wireless LAN .......................................................................................................................... 14

6.3.1 IEEE 802.11b .................................................................................................................. 14

6.3.2 IEEE 802.11g .................................................................................................................. 14

6.3.3 IEEE 802.11n .................................................................................................................. 14

6.4 Built-in NFC Tag ..................................................................................................................... 14

7 Optical Specifications ................................................................................................... 15

7.1 Basic Specifications ............................................................................................................... 15

7.2 Aiming Pattern ........................................................................................................................ 16

8 Technical Specifications .............................................................................................. 17

8.1 Barcode Test Sample ............................................................................................................. 17

8.2 Scan Area and Depth of Field ................................................................................................ 19

8.3 Printed Contrast Signal (PCS) ............................................................................................... 20

8.4 Minimum Resolution ............................................................................................................... 20

8.5 Barcode Width ........................................................................................................................ 20

8.6 Pitch, Skew and Tilt ................................................................................................................ 21

8.7 Curvature ................................................................................................................................ 21

8.8 Motion Tolerance .................................................................................................................... 22

9 Environmental Specifications ...................................................................................... 23

9.1 Temperature ........................................................................................................................... 23

9.2 Humidity .................................................................................................................................. 23

9.3 Ambient Light Immunity .......................................................................................................... 23

9.4 Dust and Drip Proof ................................................................................................................ 24

9.5 Vibration Strength (without packing) ...................................................................................... 24

9.6 Vibration Strength (in individual packing) ............................................................................... 24

9.7 Drop Impact Strength (without packaging) ............................................................................. 24

9.8 Drop Impact Strength (in individual packaging) ..................................................................... 25

9.9 Electrostatic Discharge Immunity ........................................................................................... 25

10 Regulatory Compliance ................................................................................................ 26

OPH-5000i

1st

5

10.1 LED Safety ............................................................................................................................. 26

10.2 Product Safety ........................................................................................................................ 26

10.3 EMC ........................................................................................................................................ 26

10.4 Other ....................................................................................................................................... 28

11 RoHS .............................................................................................................................. 28

12 Reliability ....................................................................................................................... 28

13 Precautions .................................................................................................................... 28

13.1 Radio Law............................................................................................................................... 29

13.2 Bluetooth ................................................................................................................................ 29

13.3 Frequency Baud ..................................................................................................................... 29

13.4 Usage Note ............................................................................................................................ 29

14 Product Labels .............................................................................................................. 30

15 Packaging Specifications ............................................................................................. 31

15.1 Individual Packaging .............................................................................................................. 31

15.2 Collective Packaging .............................................................................................................. 33

16 Physical Features .......................................................................................................... 34

16.1 Dimensions ............................................................................................................................. 34

16.2 Weight .................................................................................................................................... 34

16.3 Mechanical Drawing ............................................................................................................... 34

17 Supported Symbologies ............................................................................................... 35

17.1 Default Setting ........................................................................................................................ 35

17.2 Supported Symbologies ......................................................................................................... 35

17.2.1 1D Barcodes ................................................................................................................... 35

17.2.2 GS1 Databar, Composite Code ...................................................................................... 36

17.2.3 2D Codes ........................................................................................................................ 36

Table of Figures

Figure 1: Detailed View ......................................................................................................................... 11

Figure 2: micro USB B Connector ......................................................................................................... 13

Figure 3: Interface Circuit (USB) ........................................................................................................... 13

Figure 4: Aiming Pattern and Imaging Range ....................................................................................... 16

Figure 5: Scan Area and Depth of Field ................................................................................................ 19

Figure 6: Wide Barcode ......................................................................................................................... 20

Figure 7: Pitch, Skew and Tilt ................................................................................................................ 21

Figure 8: Curvature ................................................................................................................................ 21

Figure 9: Motion Tolerance .................................................................................................................... 22

Figure 10: Drop Test .............................................................................................................................. 24

Figure 11: Product Label Position ......................................................................................................... 30

Figure 12: Individual Packaging ............................................................................................................ 31

Figure 13: Collective Packaging ............................................................................................................ 33

Figure 14: Mechanical Drawing ............................................................................................................. 34

OPH-5000i

1st

6

1 Abstract

This manual provides specifications for the OPH-5000i 2D Handy Terminal with built-in Wireless LAN
and Bluetooth.

2 Overview

The OPH-5000i is compact imager scanner built-in and output scanned barcode and 2D code data to
hostdevice conected by TCP/IP via wiress LAN. Bluetooth is also aveliable for output.

・ OPH-5000i is handy terminal with a numeric keypad and TFT color LCD display.
・ All barcode data scanned is transmitted to a host device through the Wireless LAN, Bluetooth or

USB interface interface.

・ Wireless LAN supports IEEE 802.11 b/g/n.

・ Bluetooth SPP (Serial Port Profile) and HID (Human Interface Device Profile) are implemented.

・ In addition to the current buzzer sound and LED display, vibration function is also equipped.

・ A green LED aiming line toward a target barcode can help the users find the appropriate scanning

position.

・

Alcohol can be used to wipe the scanner clean

・

The power source is 3.7 V 1100 mAh (typ.) Li-ion battery.

・ The charging is done through a dedicated charging cradle or USB interface.

・ The scanner is Apple MFi certified.

OPH-5000i

1st

7

3 Basic Specifications

Item Specification Note

Control Section

CPU 32bit CISC/96MHz

FROM 2Mbyte + 32KByte

System area

FROM 1Mbyte

Application area

RAM 16Mbyte

It may be cleared by
the removal of the
main battery.

FROM (storage) 128Mbyte

For data area only

Input Section

Key type

Number 10 key
F1~F3 3 key
Power 1 key
Up, down, SCAN (Placed on top
panel)

3 key

SHIFT, BS, CLEAR, decimal point,
ENT

5 key

Side touch sensor 1 sensor for scan

Backlight White

Display Section

Display element TFT color LCD display

Backlight White, brightness adjustable

Display size 1.77 inch, (W)128× (L)128 dots

Font size 12/16/24 dot

Type of characters JIS Standard No.1 and 2, ANK

Structure of Characters

When in 12 dot Font mode

(digit × row)
Reduced-size ANK: 21×21
Half-size character: 21×10
Kanji character: 10×10

When in 16 dot Font mode

(digit × row)
Reduced-size ANK: 16×16
Half-size character: 16×8
Kanji character: 8×8

When in 24dot Font mode

(digit × row)
Reduced-size ANK: 10×10
Half-size character: 10×5
Kanji character: 5×5

LED red, green one place, and blue 1 place

Buzzer Loudness (3-level) / tone adjustable

Vibration motor Strength (3-level) / duration adjustable

RTC

Contents Year, month, date, hour, minute, second

Data and time are lost
when the main battery
is removed.

Accuracy ± 90 seconds per month

Interface

Wireless LAN

Specification IEEE 802.11 b/g/n compliant

Frequency 2412~2472MHz (1~13ch)

Maximum output 0.0026W/MHz

IEEE 802.11b

Access method Infrastructure mode (STA)

Security WEP,WPA,WPA2

OPH-5000i

1st

8

Item Specification Note

Network stack

TCP/IP, UDP, DHCP, ARP,
SSL, DNS

Bluetooth

Frequency 2402 ~ 2480 MHz

Specification Bluetooth Ver 2.1 compliant

Communication
distance

10 m

Not guaranteed.

Output level Class 2

Max output 4 dBm

Profile SPP / HID

Built-in NFC tag

ISO/IEC 14443 TYPE A, TYPE B
JISX6319-4

USB

・Full-Speed 12Mbps ( HID/COM )
・Hi-Power Bus-powered supported

Optical Section

Scanning method VGA CMOS area sensor

Scanning light source 1 Warm-White LED

Aiming light source 1 green LED

Effective pixels 0.30 million pixels

View angle

Horizontal: about 38.0°
Vertical: about 28.9°

Supported 1D Symbologies

Symbologies

UPC-A, UPC-A Add-on, UPC-E,
UPC-E Add-on, EAN-13, EAN-13 Add-on, EAN-8,
EAN-8 Add-on, JAN-8, JAN-13, Code 39, Tri-Optic,
NW-7, Industrial 2 of 5,
Interleaved 2 of 5, S-Code, IATA, Code 93,
Code 128, MSI/Plessey, UK/Plessey, TELEPEN,
Matrix 2 of 5, Chinese Post Matrix 2 of 5,
Code 11, Korean Postal Authority code, Postal
Code

Refer to Chapter 17.
for details

Minimum resolution Code 39 : 0.1 mm

PCS 0.9

Curvature

R ≥ 16 mm ( 9-digit JAN)
R ≥ 20 mm (13-digit JAN)

PCS 0.9

Barcode width

100 mm wide 0.2 mm resolution Code 39 (DOF 150
mm) is readable:

Motion Tolerance

UPC 100% moving at 2m/sec (DOF 100 mm)
is readable:

Depth of Field

Code 39

Resolution (0.127) 90 ~ 110

Resolution (0.254) 65 ~ 185

Resolution (0.508) 65 ~ 260

Code 128 Resolution (0.2) 85 ~ 165

UPC Resolution (0.33) 55 ~ 195

GS1/Composite

Symbologies

GS1 DataBar , GS1 DataBar Limited,
GS1 DataBar Expanded,
Composite GS1 DataBar, Composite GS1-128,
Composite EAN, Composite UPC

GS1 DataBar:
formerly called
“RSS”

Minimum resolution

GS1 DataBar : 0.169mm
Composite Code: 0.169mm

S

uppor

t

e

d

2D

Symbologies

Symbologies

PDF417 , MicroPDF417 , Codablock F ,
QR Code , MicroQR Code ,
Data Matrix ( ECC 0 - 140 / ECC 200 ) ,
MaxiCode( Modes 2 to 5 ) , Aztec Code ,
Chinese-sensible code

Disable Code 128
when Codablock F is
enabled.

OPH-5000i

1st

9

Item Specification Note

Minimum resolution (mm)

PDF417 : 0.169 mm
QR Code : 0.169 mm
DataMatrix : 0.169 mm

PCS 0.9

Depth of
field
(mm)

PDF417

Resolution (0.169) 85~ 135

PCS 0.9

Resolution (0.254) 65 ~ 180

QR Code

Resolution (0.212) 90 ~ 110

Resolution (0.381) 55 ~ 180

DataMatrix Resolution (0.254) 85 ~ 135

Common

Scan angle

Pitch : ±70°

Skew : ±70°

Tilt : ±360°

Minimum PCS 0.2 or more

MRD 32% or more

Power Section

Main battery Lithium-ion 1100 mAh (typ.)

Up-time 20 hours or more

*1

Charging time Less than 3 hour

Using dedicated
cradle.
Room temperature
25℃

Feeding system

Electromagnetic guidance wireless charging,
microUSB

Operating (charging) voltage 4.5 ~ 5.5V

Charging with USB

Current
consumption

Charging Less than 500 mA

Environmental Specifications

Temperature

Operating -10 ~ 50°C

Storage -20 ~ 60°C

Humidity

Operating 20 ~ 85%

No condensing
No frost

Storage 20 ~ 85%

Ambient light
immunity

Fluorescent 10,000 lx or less

UPC 100%
Optical axis angle 75°
Distance: 100mm

Sunlight 100,000 lx or less

Vibration

10 Hz ~ 100 Hz, acceleration of 19.6 m/s

2

, 60
minutes per cycle, repeat in each X, Y and Z­direction

Drop

Drop the scanner 18 times (6 faces x 3) from a
height of 150 cm onto a concrete floor

Dust and drip proof IP54 equivalent

Regulatory Compliance

LED safety

JIS C 6802：2011 Class2
IEC 60825-1 Ed.2: 2007 Class 2
CDRH Class Ⅱ

Product safety

EN60950-1:2005
IEC60950-1:2006

EMC

EN 55024:2010
EN 55032:2012+AC: 2013
EN 301 489-1 V1.9.2
EN 301 489-17 V2.2.1
EN 300 328 V1.9.1
EN 302 291-2 V1.1.1
FCC Part 15 Subpart C, Subpart B Class A
VCCI Class A

For residential,
commercial and light­industrial
environments

European conformity CE Marking

OPH-5000i

1st

10

Item Specification Note

Certification for Construction Design of Specified
Radio Equipment

Other

Bluetooth logo certification
MFi license

Immunity

Test

ESD

No
distraction

Air discharge (direct): ±15 kV

Conditions:
IEC61000-4-2
compliant

No
malfunction

Air discharge (direct): ±8 kV

Physical

Features

Dimensions 136 × 44 × 30.3(22) (WDH mm)

() is grip dimension
Not include projection

Weight Approx. 120 g

Excluding accessories
Including main battery

*1: When a barcode is read twice every 10 seconds at room temperature 25℃.

4 Detailed View

9

3

4

5

6

7

8

1

2

10

11

6

12

13

14

15

16

OPH-5000i

1st

11

Figure 1: Detailed View

OPH-5000i

1st

12

No Name Description

1 LED

Indicates operational status, such as scanning and
communication.
It is able to be controlled by user’s programs.

2 LCD Indicates scanned barcodes and operational items.

3 MicroUSB Connecter Cap MicroUSB connector is stored.
4 Buzzer Orifice Holes for buzzer.
5 Strap Orifice Holes for attaching a hand strap.
6 Scan Window LED illumination is emitted from this window to read barcodes.
7 Battery Cover Rechargeable battery is stored.
8 Battery Cover Lock Used to lock / open the battery cover.

9 Charging Coil

The charging coil is located here with which the dedicated cradle
can su

pply p

ower to the scanner.

10 NFC

This is the location of the NFC tag. Hold an NFC reader close to
this area when the ta

g

has to be read.

11 Side Trigger Sensor Start an operation of reading code by touching.
12 Trigger Key Press when reading code.
13 Up and Down Key Key use for selecting item and moving cursor.

14 Numeric Keypad

Numeric, enter, decimal point key and the key’s to support these
inputs.

15 F1, F2, F3 Function key.
16 Power Key Power On/Off key.

5 El

e

5.1 E

S

uBuCu

5.2

W

F

ePo

6 In

t

The OP

H

6.1 U

In

6.1.1

C

6.1.2

ctrical

S

lectrical

S

pply Voltag
s-power (C

l

rrent cons

u

ireless C

eding syste
wer consu

m

erface

S

-5000i inte

r

SB Interf

a

terface is F

u

onnecto

r

Signal

N

VC

DAT

A

DAT

A(NC

GN

USB Interf

a

pecific

a

pecificat

i

e

ass)
mption

harging

m

ption

pecific

a

face is sele

c

ce

ll Speed US

ame

C

C

(-)

(+)

)

D

ce Circui

t

Po

w

Su

p

Micro­controller

tions

ons

: 4.5-5.5

V

: Hi-Pow

e

: Less th

a

: Electro

m

: Less th

a

tions

table from t

h

B interface.

ontact Nu

m

1

2

3

4

5

Figure 3:

er

ly

r ( 500mA

m

n 500mA

agnetic ind

u

n 5W

ree types;

U

ber

Interface Cir

c

ax )

ction

SB / Bluet

o

Fig

u

uit (USB)

oth and Wir

e

re 2: micro U

S

USB Connec

t

O

less LAN.

B B Connec

t

tor

PH-5000i

1st

13

or

OPH-5000i

1st

14

6.2 Bluetooth

The specifications of the OPH-5000i Bluetooth interface are as follows:
Specification : Bluetooth Ver 2.1 compliant

Frequency : 2402 MHz ~ 2480 MHz

Communication distance : 10 m

Output level : Class 2 (max 4 dBm)

Implemented profile : SPP / HID

Communication configuration : 1 to 1

Operating mode in communication : Master / Slave mode

Security mode : Authentication supported

Encryption : Encryption supported

6.3 Wireless LAN

The specifications of the OPH-5000i Bluetooth interface are as follows:
Specification : IEEE 802.11 b/g/n compliant

Frequency : 2412 MHz ~ 2472MHz (1~13ch)

Access method : Infrastructure mode, (STA)

Security : WEP 64/128, WPA-TKIP, 128-bit WPA2 CCMP (AES)

Network stack : IP, TCP, UDP, DHCP, ARP, SSL, DNS

6.3.1 IEEE 802.11b

Maximum output : 0.0026W/MHz

Supported data rate : 1, 2, 5.5, 11Mbps

6.3.2 IEEE 802.11g

Maximum output : 0.0013W/MHz

Supported data rate : 6, 9, 12,18, 24, 36, 48, 54Mbps

6.3.3 IEEE 802.11n

Maximum output

: 0.0007W/MHz

Supported data rate

: 6.5, 7.2, 13.0, 14.4, 19.5, 21.7, 26.0, 28.9, 39.0, 43.3,

52.0, 57.8, 58.5, 65.0, 72.2Mbps

6.4 Built-in NFC Tag

OPH-5000i has NFC tag built-in which record Bluetooth device address.
Frequency : 13.56MHz

Standard : ISO/IEC 14443 TYPE A, TYPE B and JISX6319-4

OPH-5000i

1st

15

Recorded Contents:

T

otal 928 byte

NDEF

Record #1

t

ype: ”application/vnd.bluetooth.ep.oob”
OOB data length: 8 Byte
MAC address: 00:12:6A:xx:xx:xx

Record #2

t

ype: ”T”

T

EXT data length: 15 Byte

T

EXT data: ”00126Axxxxxx”

Free area

Reserved area

*xx differ depending on the product.

Rewriting from external: possible

7 Optical Specifications

7.1 Basic Specifications

Item Characteristics

Scan method CMOS area sensor (white / black) -

Number of effective pixel (Column) × (Row) 640 × 480 dots

Image capture speed (*1) Frame rate 100 fps

Focal distance Distance from the front edge of scanner 109.2mm

View angle

Horizontal Approx. 38.0°

Vertical Approx. 28.9°

Diagonal Approx. 46.4°

Illumination light source
(LED × 1)

Color Warm white

Color temperature

2600～3700K

Maximum radiation output (*3) 114lm/W

Aiming light source
(LED × 1)

Color Green

Peak wavelength 535 nm

Maximum radiation output (*4) 87.4m/W

*1 The fastest seed of image capture
*2 Reference value extracted from the datasheet.
*3, *4 Reference value based on the datasheet (25°C, IF = 140 mA ).

7.2

A

T12 T--

iming Pa

t

he aiming i

s

. Fill light t

o

. Fill light w

he aiming

s

The horizo

n

a distance

The horizo

n

aiming wid

t

tern

used for t

h

recognize t

h

hen auto tri

g

pecification

s

tal width of

of L=85±20

tal imaging

h.

F

i

e following

p

e appropri

a

ger is used.

are as foll

o

the imaging
mm from th

e

field of view

gure 4: Aimin

urpose:

te reading r

a

ws:
field of vie

w

front edge

o

at a distan

c

g Pattern an

d

nge.

and the hor

f the scann

e of L=85 m

Imaging Ra

n

zontal aimi

n

r.

is 100%±

1

ge

O

g width are

0% of the h

PH-5000i

1st

16

qual at

orizontal

OPH-5000i

1st

17

8 Technical Specifications

Aim the laser light at the center of a code to scan it. For long distance scanning, ambient light entering
the angle of view may affect the scanning performance. The conditions for technical specifications are
as follows, unless otherwise specified in each section.

<Conditions>
Ambient Temperature and Humidity Room temperature, room humidity

Ambient Light 100 ~200 lux (on the surface of a barcode)
Angles Pitch: α = 0°, Skew: β = 15°, Tilt: γ = 0°
Curvature R = ∞
Power Supply Voltage 5.0 V
PCS (1D and 2D) 0.9 or higher

Scanning Test Accept the performance with 90% or more success rate

for 10 tries of scan. One reading should be 2 seconds.

Barcode Test Sample (1D and 2D)

Specified below.

< Test chart >
For 1D codes, OPTOELECTRONICS test samples
For GS1 Databar, stacked codes and 2D codes, printed by a dedicated printer for barcode

8.1 Barcode Test Sample

1D Barcodes

<Code 39>

Resolution Symbology PCS Size (mm) No. of Digits

0.1 mm (3.9 mil)

Code 39 0.9

26 × 10 16

0.127 mm (5 mil)

11 × 10 4

0.20 mm (7.9 mil)

100 × 10 31

0.254 mm (10 mil)

32.5 × 10 7

0.508 mm (20 mil)

43 × 25 4

<Code 128>

Resolution Symbology PCS Size (mm) No. of Digits

0.20 mm (7.9 mil) Code 128 0.9 52 × 10 36

<UPC>

Resolution Symbology PCS Size (mm) No. of Digits

0.330 mm (13 mil)

12-digit UPC
12-digit EAN

0.9/0.2 31.5 × 24.5 12/13

GS1 Databar/Composite

<GS1-limited>

Resolution Symbology PCS Size (mm) No. of Digits

0.169 mm (6.7 mil) Limited 0.9 12 × 1.5 14

0.169 mm (6.7 mil) Limited-Composite 0.9 12 × 3.0 26

OPH-5000i

1st

18

2D Codes

<PDF417>

Resolution Error Correction PCS Size (mm)

No. of Character

0.169 mm (6.7 mil)
Level-3 0.9

23 × 10

58

0.254 mm (10 mil) 35 × 15

<QR Code: Model-2>

Resolution Error Correction PCS Size (mm)

No. of Character

0.212 mm (8.4 mil)

M 0.9

5 × 5

44

0.381 mm (15 mil) 11 × 11

<Data Matrix>

Resolution Model PCS Size (mm)

No. of Character

0.212 mm (8.4 mil)

ECC200 0.9

4 × 4

40

0.254 mm (10 mil) 6 × 6

* The size is outline dimensions excluding the quiet zones.

OPH-5000i

1st

19

8.2 Scan Area and Depth of Field

The scan area is the depth of field range, measured from the front edge of the scanner, swept
over the entire scan arc.

100 200 300

50 150 250

[単位：mm]

18

Figure 5: Scan Area and Depth of Field

[Unit: mm]

OPH-5000i

1st

20

8.3 Printed Contrast Signal (PCS)

0.2 or higher

<Conditions>
MRD : 32% and higher

(70% or higher reflectivity of space and quiet zone)
Distance : 125mm from the front edge of the scanner
Barcode Sample : UPC specified in Chapter 8. (Resolution: 0.33 mm, PCS: 0.3)

MRD = Minimum reflectance of white bar - Maximum reflectance of black bar

8.4 Minimum Resolution

1D Code : 0.1 mm (3.9 mil) Code 39 specified in Chapter 8.1
GS1-Databar : 0.169 mm (6.7 mil) GS1 Databar Limited specified in Chapter 8.1
Stacked Code : 0.169 mm (6.7 mil)

PDF417, GS1 Databar Limited Composite specified in Chapter 8.1

2D Code : 0.169 mm (6.7 mil) QR Code, Data Matrix specified in Chapter 8.1

<Conditions>
Barcode Sample : The above codes specified in Chapter 8.1
Distance : 95 mm from the front edge of the scanner
Angle

: α = 0°, β =＋15°, γ = 0°

Curvature : R = ∞

8.5 Barcode Width

Code 39 with width of 100 mm and resolution of 0.2 mm can be read

<Conditions>
Barcode Sample : 0.20 mm Code 39 / PCS 0.9 specified in Chapter 8.1
Distance : 155 mm from the front edge of the scanner
Angle

: α = 0°, β =＋15°, γ = 0°

Curvature : R = ∞

Figure 6: Wide Barcode

PCS =

Reflectance of white space – Reflectance of black bar

Reflectance of white space

OPH-5000i

1st

21

8.6 Pitch, Skew and Tilt

Pitch : α = ±50°
Skew : β = ±50°
Tilt : γ = ±180°

<Conditions>
Barcode Sample : 0.33 mm Code 39 specified in Chapter 7.1
Distance : 125 mm from the front edge of the scanner
Curvature : R = ∞
* For the pitch angle and tilt angle measurement, set the skew angle β = +15°

β

γ

+

+

+

-

-

-

Figure 7: Pitch, Skew and Tilt

8.7 Curvature

0.33 mm 12-digit UPC : R ≧ 20 mm

0.15 mm 10-digit Codabar(NW-7) : R ≧ 16 mm

<Conditions>

Barcode Sample 0.33 mm UPC, 0.15 mm Codabar specified in Chapter 8.1
Distance 105 mm from the edge of the scan engine
Angle Skew angle β = +15°

R

バーコード

Figure 8: Curvature

Note: Scanning may fail due to the specular reflection of the LED illumination when the reflectivity of the barcode
is high.

OPH-5000i

1st

22

8.8 Motion Tolerance

UPC 100% can be read when it is moving at 2m/s.

<Conditions>

Ambient Temperature and Humidity : Room temperature and Room humidity
Ambient Light : 500 ~ 1000 lux
Distance : 125 mm from the front edge of the scanner
PCS (1D and 2D) : 0.9 or higher
Barcode Sample : Refer to Chapter 8.1.

* Scanning may fail due to the specular reflection of LED illumination when the reflectivity is high.

Figure 9: Motion Tolerance

OPH-5000i

1st

23

9 Environmental Specifications

9.1 Temperature

Scanning performance is guaranteed when the ambient temperature around the scanner is
within the following ranges:

Operating Temperature : -10 ~ 50

°C

Storage Temperature : -20 ~ 60 °C

Please charge when the temperature is between 0 and 40°C. When the temperature is over 40°C,
charging may stop to prevent battery breakdown.

<Conditions>

Barcode : Resolution 0.33 mm, 9-digit Code 39 specified in Section 9.1.
Distance : 125 mm from the front edge of the scanner
Angle

: α = 0°, β =＋15°, γ = 0°

Curvature : R = ∞
Scanning Test : Scan at interval 1000ms
Power consumption : 3.7V

9.2 Humidity

Scanning performance is guaranteed when the ambient humidity around the scanner is within
the following ranges:

Operating Humidity : 20 ~ 85%RH (no condensation, no frost)
Storage Humidity : 20 ~ 85%RH (no condensation, no frost)

<Conditions>

Barcode : Resolution 0.33 mm, 9-digit Code 39 specified in Section 9.1.
Distance : 125 mm from the front edge of the scanner
Angle

: α = 0°, β =＋15°, γ = 0°

Curvature : R = ∞
Scanning Test : Scan at interval 1000ms
Power consumption : 3.7V

9.3 Ambient Light Immunity

Scanning performance is guaranteed when the range of illumination on a barcode surface is
between zero and the following values:

Incandescent light: 10,000 lx
Fluorescent light: 10,000 lx
Sunlight: 100,000 lx

<Conditions>

Barcode: Resolution 0.33 mm, 9-digit Code 39 specified in Section 9.1.
Distance: 125 mm from the front edge of the scanner
Angle:

α = 0°, β =＋15°, γ = 0°

Curvature: R = ∞
Power consumption: 3.7V

Avoid direct or specula reflection from the light source as it may blind the scanners optical receiver.

OPH-5000i

1st

24

9.4 Dust and Drip Proof

IEC IP54 equivalent

Protection against solid objects: Level 5 equivalent (Dust proof type)
Prevent dust ingress to inside. Even if slight dust intrusion will not inhibit normal operation.

Protection against liquids: Level 4 equivalent (Splash proof type)
Protected against water splash from any direction.

* () is JIS drip-proof type.

9.5 Vibration Tolerance (without packing)

There shall be no malfunction after the following vibration test.

Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an acceleration

velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in the non-operating state.
Repeat this of each X, Y and Z direction.

9.6 Vibration Tolerance (in individual packing)

There shall be no malfunction after the following vibration test.

Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerattion

velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state.
Repeat this of each X, Y and Z direction.

9.7 Drop Impact Tolerance (without packaging)

There shall be no malfunction after the following drop test.

Drop test: Drop the scanner 18 times in total (3 times at each 6 face), from a height of 150 cm

onto a concrete floor as shown below.

150cm

Figure 10: Drop Test

OPH-5000i

1st

25

9.8 Drop Impact Tolerance (in individual packaging)

There shall be no sign of malfunction after the following drop test.

Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges,

and 6 faces, from a height of 150 cm onto a concrete floor.

9.9 Electrostatic Discharge Immunity

Air discharge ±8 kV max. (No malfunction)

±15 kV max. (No destruction)

Measurement environment An electrostatic testing device compliant with IEC 61000-4-2

is used.
Discharge resistance 330 Ω
Charging capacitor 150 pF

OPH-5000i

1st

26

10 Regulatory Compliance

10.1 LED Safety

IEC 62471:2006 Exempt_Group

10.2 Product Safety

EN60950-1:2005
IEC60950-1:2006

10.3 EMC

・EN 55024:2010
・EN 55032:2012+AC: 2013
・EN 301 489-1 V1.9.2
・EN 301 489-17 V2.2.1
・EN 300 328 V1.9.1
・EN 302 291-2 V1.1.1

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose of
used batteries according to the manufacturer’s instructions

OPH-5000i

1st

27

FCC Part 15 Subpart C, Subpart B Class A

VCCI Class A

Federal Communications Commission Notices

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case users will be required
to correct the interference at their own expense.

Harmful Interference Notice
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

This device complies with FCC SAR exposure limits set forth for an uncontrolled
environment. SAR compliance for using the equipment in close proximity to the human
body has been evaluated at 0mm.

This equipment must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna installation
instructions and consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

Caution!
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

This is a Class A product based on the standard of the Voluntary Control Council for Interference
(VCCI). If this equipment is used in a domestic environment, radio interference may occur, in
which case the user may be required to take corrective actions.

OPH-5000i

1st

28

10.4 Other

・Bluetooth logo certification
・MFi license
・Certification for Construction Design of Specified Radio Equipment

・Classification of Specified

Radio Equipment

Article 2 Paragraph 1, Item 19 Low power data
communication system in 2.4 GHz band

・Model Name OPA-26X1
・Certificate Number 201-125603

・Classification of Specified

Radio Equipment

Article 2 Paragraph 1, Item 19 Low power data
communication system in 2.4 GHz band

・Wireless LAN Model Name ATWINC1500-MR210PB
・Certificate Number

007-AD0199

11 RoHS

RoHS compliance.

RoHS: The restriction of the use of certain hazardous substances in electrical and
electronic equipment, 2011/65/EU

12 Reliability

MTBF (Mean Time Between Failures) 50,000 hours

13 Precautions

Handle this product carefully. Do not deliberately subject it to any of the following.

(1) Shock:

・ Do not drop this product from a height greater than specified in this manual.
・ Do not place this product under or between any heavy items.
・ Do not swing the cable around.

(2) Temperature Conditions:

・ Do not use this product at temperatures outside the specified range.
・ Do not pour boiling water on this product.
・ Do not throw this product into a fire.

(3) Foreign Materials:

・ Do not immerse this product in water or other liquid.
・ Do not expose this product to chemicals.

(4) Others

・ Do not disassemble this product.
・ Do not use this product near a radio or a TV. It may cause reception problems.
・ This product may be affected by a momentary voltage drop caused by lightning.
・ Do not place pieces of metal such as coins, nor attach metallic foil to the area where the

charging coil is located.
Also, do not affix anything which prevent from placing OPH-5000i to cradle.

・ Although surface of LCD is tempered glass, but do not drop or hit any hard object on purpose.

OPH-5000i

1st

29

13.1 Radio Law

This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data
communication system and has obtained the Certification for Construction
Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan.

The following activities are prohibited under the Radio Law:

・Remodelling and disassembly
・Peeling off the certificate label

Do not use this equipment under the following environment, as radio interference may affect
other device and end up with causing physical or material damage.

・Safety apparatus and medical device for human body protection
・Environment where is concerned to cause serious damage

13.2 Bluetooth

・This product supports Bluetooth wireless communication with other Bluetooth devices that

have the same profile

・This product complies with Bluetooth standards; however, its communication performance

with untested devices is not guaranteed.

・Bluetooth devices use the 2.4 GHz frequency band that is shared among other devices. It

may affect the communication speed and distance between this product and the host device.

・The communication speed and distance vary depending on the interference and radio wave

condition between this product and the host device.

13.3 Frequency Band

This product uses the 2.4 GHz frequency band. Read carefully the followings before using this
product.

In the frequency band of this product, scientific, medical and industrial devices including
microwaves are used. Also other radio stations including local private radio station for mobile
object identification requiring license for such as manufacturing lines at factories, specific
power-saving radio station requiring no license and amateur radio station are managed.

1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before
using this product.

2. In case that radio interference occurs between this product and “other radio stations,” change
the service space immediately, or stop transmitting radio wave to avoid the interference.

3. If you have any questions or troubles, please contact our sales office.

13.4 Usage Note

・Do not attach metal foil or piece of metal to charging coil storage part. Also, do not insert
metal like coins between scanner and dedicated cradle when charging.
・Be careful of dust or foreign objects inserting when opening battery cover. Precisions dust
and drip proof may not be satisfied.

* This specification manual is subject to change without prior notice.

OPH-5000i

1st

30

14 Product Labels

The product labels are affixed to the scanner as shown below.

Figure 11: Product Label Position

OPH-5000i

1st

31

15 Packaging Specifications

15.1 Individual Packaging

Assembled package size: 125 × 112 × 40 (WDH mm)
Weight: Approx. xx kg

Figure 12: Individual Packaging

MADE IN

▲▲▲▲▲

Model No.

MODEL NEME

Spec No.

*ﾊﾞｰｺｰﾄﾞ*

*△△△△△△*

Serial No.

Quantity 1

Ｒｏ

OPH-5000i-BLK

ｼﾘｱﾙNo.の 表示に つい て

『 123456 』

123456＝ 製品ｼﾘｱﾙNo.

6桁のｼﾘｱﾙNo.を 表示

【国内向】 個装箱ﾊﾞｰｺｰﾄﾞﾗﾍﾞﾙ (3A0002）

【原産国表示】～country of origin～

中国生産（produced in China）＝MADE IN CHINA
日本生産（produced in Japan）＝MADE IN JAPAN

*UF1OPH5000*

Poly bag

2回、巻き付ける

梱包袋：

MicroUSBｹｰﾌﾞﾙ
イラストの向きで
一番上に入れる

ﾈｯｸｽﾄﾗｯﾌﾟ

LDCを上にして入れる

個装箱

余った梱包袋の上に
ネックストラップを入れる

Wrap twice

Packing bag

MicroUSB cable

Place as the

drawing on top.

Neck strap

Individual box

Put in with LCD upward

Place neck strap on

top of the space

OPH-5000i

1st

32

15.2

C

1

0AsW

N

oOp

ollective

P

0pcs per b

o

sembled p

a

eight: Appr

o

te: ‘Ro mark’
toelectronic

s

ackagin

g

x
ckage size
x. xx kg

on the trays

a

Co., Ltd.

: 595 × 52

0

nd boxes ind

Figure 1

3

× 245 (WD

icates that th

e

: Collective

P

H mm)

product is R

o

ackaging

HS complia

n

O

t as is declar

e

PH-5000i

1st

33

d by

OPH-5000i

1st

34

16 Physical Features

16.1 Dimensions

136 × 44 × 30.3(22) (DWH mm) () is grip dimensions

16.2 Weight

Approx. 120 g (excluding accessories)

16.3 Mechanical Drawing

Figure 14: Mechanical Drawing

Unit: mm

OPH-5000i

1st

35

17 Supported Symbologies

17.1 Default Setting

The scanner is set to default by reading the following menu label.

Default

17.2 Supported Symbologies

17.2.1 1D Barcodes

Code type Default

Minimum

length

Remarks

UPC ○ -

UPC Add-on 2
UPC Add-on 5

EAN(JAN) ○ -

EAN Add-on 2
EAN Add-on 5

EAN-13 ○
EAN-13 Add-on 2
EAN-13 Add-on 5
EAN-8 ○
EAN-8 Add-on 2
EAN-8 Add-on 5

Code 39 ○ 1 Not transmit ST/SP

Tri-Optic ○ - Not transmit ST/SP

Codabar (NW7) ○ 1 Not transmit ST/SP

Industrial 2of 5 ○ 5

Interleaved 2of 5 ○ 6

S-Code 5
Code 128 ○ 1 GS1 conversion (setting required)

Code 93 ○ 1

IATA ○ 5

MSI/Plessey 3

UK/Plessey 2

Telepen 1

Code 11 1

Matrix 2 of 5 5

Chinese Post Matrix 2 of 5 -

Korean Postal Authority -

Intelligent Mail Barcode -

POSTNET -

JPN (Customer Barcode) -

@MENU_OPTO@ZZ@SO@ZZ@OTPO_UNEM@

OPH-5000i

1st

36

17.2.2 GS1 Databar, Composite Code

Code type Default Remarks

GS1 DataBar

・GS1 DataBar Omnidirectional
・GS1 DataBar Truncated
・GS1 DataBar Stacked
・GS1 DataBar Stacked Omnidirectional

○

GS1

conversion (setting required)

GS1 DataBar Limited ○
GS1 DataBar Expanded

・GS1 DataBar Expanded
・GS1 DataBar Expanded Stacked

○

Composite GS1-DataBar

・CC-A
・CC-B
・Limited CC-A
・Limited CC-B
・Expanded CC-A
・Expanded CC-B

GS1

conversion (setting required)

Composite GS1-128

・CC-A
・CC-B
・CC-C

GS1

conversion (setting required)

Composite EAN

・EAN-13 CC-A
・EAN-13 CC-B
・EAN-8 CC-A
・EAN-8 CC-B

GS1

conversion (setting required)

Composite UPC

・UPC-A CC-A
・UPC-A CC-B
・UPC-E CC-A
・UPC-E CC-B

GS1

conversion (setting required)

17.2.3 2D Codes

Code type Default Remarks

PDF417 ○

Micro PDF417

Codablock F

QR Code ○ GS1 conversion (setting required)

Micro QR ○

Data Matrix (ECC 200) ○ GS1 conversion (setting required)

Data Matrix (ECC 000-140)

Aztec Code ○

Aztec Runes

Chinese-sensible code

Maxi Code

* The supported symbologies vary depending on specifications for the application to be loaded.