Product Bulletin OPB760N
June 1996
Photologic® Reflective Object Sensors
Types OPB760N, OPB761N, OPB762N, OPB763N
Features
∙Choice of mounting configurations
∙Choice of output configurations
Description
The OPB760N series of reflective assemblies feature Photologic® output. This electrical output can be specified as either TTL Totem Pole or
TTL Open Collector. Either may be supplied with inverter or buffer output polarity. All have the added stability of a built-in hysteresis amplifier.
Mounting Options
OPB760N series PC board mount, without mounting tabs
OPB760T series PC board mount, with two mounting tabs
OPB770N series wire leads with connector, without mounting tabs
OPB770T series wire leads with connector, with two mounting tabs
Absolute Maximum Ratings (TA = 25o C unless otherwise noted)
Supply Voltage, VCC (Not to exceed 3 sec.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40o C to +85o C
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40o C to +70o C
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 sec. with soldering iron] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240oC(1) Input Diode Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW(2) Output Photologic® Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mW(3)
Total Device Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 mW(4)
Voltage at Output Lead (Open Collector Output) . . . . . . . . . . . . . . . . . . . . . . . . . . 35 V Diode Forward D.C. Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA Diode Reverse D.C. Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 V
Notes:
(1)RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering.
(2)Derate linearly 2.22 mW/o C above 25o C.
(3)Derate linearly 4.44 mW/o C above 25o C.
(4)Derate linearly 6.66 mW/o C above 25o C.
(5)The OPB760N thru OPB763N series are terminated with .020" square leads designed for printed circuit board mounting.
(6)Normal application would be with light source blocked, simulated by IF = 0mA.
(7)Tested at d = 0.080" from a 90% diffuse white test surface.
(8)Tested at d = 0.080", 0.150" and 0.220" from a 90% diffuse white test surface. Reference: Eastman Kodak, Catalog #1257795.
(9)Tested at d = 0.080", 0.150" and 0.220" from a 5% diffuse black test surface.
(10)All parameters tested using pulse technique.
Optek Technology, Inc. |
1215 W. Crosby Road |
Carrollton, Texas 75006 |
(972) 323-2200 |
Fax (972) 323-2396 |
11-50
Types OPB760N, OPB761N, OPB762N, OPB763N
Electrical Characteristics (TA = -40o C to +70o C unless otherwise noted)
SYMBOL |
PARAMETER |
Input Diode |
|
VF |
Forward Voltage |
IR Reverse Current
Output Photologic® Sensor
VCC
ICCL
ICCH
IOH
IF(+)
IF(+)/IF(-)
IOS
VOL
VOL
VOH
VOH
Operating D.C. Supply Voltage
Low Level Supply Current:
Buffered Totem-Pole Output
Buffered Open-Collector Output
Inverted Totem-Pole Output
Inverted Open-Collector Output
High Level Supply Current:
Buffered Totem-Pole Output
Buffered Open-Collector Output
Inverted Totem-Pole Output
Inverted Open-Collector Output
High Level Output Voltage:
Buffered Open-Collector Output
Inverted Open-Collector Output
LED Positive-Going Threshold Current
Hysteresis
Short Circuit Output Current:
Buffered Totem-Pole Output
Inverted Totem-Pole Output
Low Level Output Voltage:
Buffered Totem-Pole Output
Buffered Open-Collector Output
Inverted Totem-Pole Output
Inverted Open-Collector Output
Low Level Output Voltage:
Buffered Totem-Pole Output
Buffered Open-Collector Output
High Level Output Voltage:
Buffered Totem-Pole Output
Inverted Totem-Pole Output
High Level Output Voltage:
Inverted Totem-Pole Output
Inverted Open-Collector
MIN |
TYP MAX UNITS |
TEST CONDITIONS |
||
|
1.8 |
V |
IF = 40 mA, TA = 25o C |
|
|
100 |
μA |
VR = 2 V, TA = 25o C |
|
4.75 |
5.25 |
V |
|
|
|
10 |
mA |
VCC = 5.25 V, IF = 0 mA(6)(7) |
|
|
Output Open |
|||
|
|
|
||
|
10 |
mA |
VCC = 5.25 V, IF = 25 mA(7) |
|
|
Output Open |
|||
|
|
|
||
|
10 |
mA |
VCC = 5.25 V, IF = 25 mA(7) |
|
|
Output Open |
|||
|
|
|
||
|
10 |
mA |
VCC = 5.25 V, IF = 0 mA(6)(7) |
|
|
Output Open |
|||
|
|
|
||
|
100 |
μA |
VCC = 4.75 V, VOH = 30 V |
|
|
IF = 25 mA, TA = 25o C |
|||
|
100 |
μA |
VCC = 4.75 V, VOH = 30 V, |
|
|
IF = 0 mA, TA = 25o C |
|||
|
25 |
mA |
VCC = 5 V, TA = 25o C(8) |
|
|
|
|
VCC = 5 V(8) |
|
-15 |
-100 |
mA |
VCC = 5.25 V, IF = 25 mA(7) |
|
|
Output = GND |
|||
|
|
|
||
-15 |
-100 |
mA |
VCC = 5.25 V, IF = 0 mA(7) |
|
Output = GND |
||||
|
|
|
||
|
0.4 |
V |
VCC = 4.75 V, IOL = 12.8 mA |
|
|
IF = 0 mA(6)(7) |
|||
|
0.4 |
V |
VCC = 4.75 V, IOL = 12.8 mA |
|
|
IF = 25 mA(6)(7) |
|||
|
0.4 |
V |
VCC = 4.75 V, IOL = 12.8 mA |
|
|
IF = 30 mA(9) |
|||
2.4 |
|
V |
VCC = 4.75 V, IOH = -800 μA |
|
|
IF = 25 mA(7) |
|||
|
|
|
||
2.4 |
|
V |
VCC = 4.75 V, IOH = -800 μA |
|
|
IF = 0 mA(6)(7) |
|||
|
|
|
||
2.4 |
|
V |
VCC = 4.75 V, IOH = -800 μA |
|
|
IF = 30 mA(9) |
|||
|
|
|
Optek reserves the right to make changes at any time in order to improve design and to supply the best possible product.
Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 (972) 323-2200 Fax (972) 323-2396
11-51