ON Semiconductor BAS116LT1 Datasheet
SEMICONDUCTOR TECHNICAL DATA
Order this document
by BAS116LT1/D
This switching diode has the following features:
• Low Leakage Current Applications
• Medium Speed Switching Times
• Available in 8 mm Tape and Reel
Use BAS116LT1 to order the 7 inch/3,000 unit reel
Use BAS116LT3 to order the 13 inch/10,000 unit reel
3
CATHODE
MAXIMUM RATINGS
Rating Symbol Value Unit
Continuous Reverse Voltage V
Peak Forward Current I
Peak Forward Surge Current I
THERMAL CHARACTERISTICS
Characteristic Symbol Max Unit
Total Device Dissipation FR–5 Board
TA = 25°C
Derate above 25°C
Thermal Resistance, Junction to Ambient
Total Device Dissipation
Alumina Substrate
Derate above 25°C
Thermal Resistance, Junction to Ambient
Junction and Storage Temperature TJ, T
(2)
TA = 25°C
(1)
DEVICE MARKING
BAS116LT1 = JV
ELECTRICAL CHARACTERISTICS (T
Characteristic Symbol Min Max Unit
= 25°C unless otherwise noted)
A
OFF CHARACTERISTICS
Reverse Breakdown Voltage (IBR = 100 µAdc) V
Reverse Voltage Leakage Current (VR = 75 Vdc)
Reverse Voltage Leakage Current (VR = 75 Vdc, TJ = 150°C)
Forward Voltage (IF = 1.0 mAdc)
Forward Voltage (IF = 10 mAdc)
Forward Voltage (IF = 50 mAdc)
Forward Voltage (IF = 150 mAdc)
Diode Capacitance (VR = 0 V, f = 1.0 MHz) C
Reverse Recovery Time (IF = IR = 10 mAdc) (Figure 1) t
1. FR–5 = 1.0 0.75 0.062 in.
2. Alumina = 0.4 0.3 0.024 in. 99.5% alumina.
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 1
R
F
FM(surge)
P
D
R
q
JA
P
D
R
q
JA
stg
1
ANODE
(BR)
I
R
V
F
D
rr
Motorola Preferred Device
3
1
2
CASE 318–08, STYLE 8
SOT–23 (TO–236AB)
75 Vdc
200 mAdc
500 mAdc
225
1.8
556 °C/W
300
2.4
417 °C/W
–55 to +150 °C
75 — Vdc
—
—
—
—
—
—
— 2.0 pF
— 3.0 µs
5.0
80
900
1000
1100
1250
mW
mW/°C
mW
mW/°C
nAdc
mV
Motorola Small–Signal Transistors, FETs and Diodes Device Data
Motorola, Inc. 1997
1
BAS116LT1
820
Ω
+10 V
0.1 µF
2.0 k
100
I
t
t
r
0.1
µ
I
F
µ
H
F
p
10%
t
F
t
rr
t
50 Ω OUTPUT
PULSE
GENERATOR
DUT
50
Ω
INPUT
SAMPLING
OSCILLOSCOPE
Notes: 1. A 2.0 kΩ variable resistor adjusted for a Forward Current (IF) of 10 mA.
Notes: 2. Input pulse is adjusted so I
Notes: 3. tp » t
rr
V
R
R(peak)
90%
INPUT SIGNAL
is equal to 10 mA.
I
R
Figure 1. Recovery Time Equivalent Test Circuit
i
= 1.0 mA
R(REC)
OUTPUT PULSE
(IF = IR = 10 mA; MEASURED
at i
R(REC)
= 1.0 mA)
2
Motorola Small–Signal Transistors, FETs and Diodes Device Data
Loading...