Omron V680-HS65, V680-HA63A, V680-H01-V2, V680-HS63, V680-D1KP52MT User Manual
...
RFID System
V680 Series
User's Manual for Amplifiers, Antennas, and RF Tags
(EEPROM)
Amplifier and Antennas
V680-HA63A
V680-HS51
V680-HS52
V680-HS63
V680-HS65
V680-H01-V2
RF Tags
V680-D1KP52MT
V680-D1KP52M-BT01
V680-D1KP52M-BT11
V680-D1KP53M
V680-D1KP54T
V680-D1KP66T
V680-D1KP66MT
V680-D1KP66T-SP
V680-D1KP58HTN
Man. No.: Z262-E1-09A
Introduction
Thank you for purchasing a V680-series RFID System. This manual describes the functions, performance,
and application methods needed for optimum use of the V680-series RFID System.
Please observe the following items when using the RFID System.
• Allow the RFID System to be installed and operated only by qualified specialist with a sufficient
knowledge of electrical systems.
• Read and understand this manual before attempting to use the RFID System and use the RFID System correctly.
• Keep this manual in a safe and accessible location so that it is available for re feren c e when re qu ired .
Introduction
Section 1
Section 2
Section 3
Section 4
Section 5
READ AND UNDERSTAND THIS DOCUMENT
Product Overview
Specifications and Performance
Communications Specifications
Installation
Chemical Resistance
Introduction
Section 1 Section 2 Section 3 Section 4 Section 5
RFID System
V680-HA63A Amplifier
V680-HS51 Antenna
V680-HS52 Antenna
V680-HS63 Antenna
V680-HS65 Antenna
V680-H01-V2 Antenna
V680-D1KP52MT RF Tag
V680-D1KP52M-BT01 RF Tag
V680-D1KP52M-BT11 RF Tag
V680-D1KP53M RF Tag
V680-D1KP54T RF Tag
V680-D1KP66T RF Tag
V680-D1KP66MT RF Tag
V680-D1KP66T-SP RF Tag
V680-D1KP58HTN RF Tag
User's Manual
Introduction
Introduction
READ AND UNDERSTAND THIS DOCUMENT
Please read and understand this document before using the products. Please consult your OMRON representative if you have any qu estions or comments.
WARRANTY
OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN
ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON’S
ANALYSIS CO NFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
SUITABILITY FOR USE
THE PRODUCTS CONTAINED IN THIS DOCUMENT AR E NOT S AFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF
PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to
separate catalogs for OMRON's safety rated products.
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of produc t s in th e customer’s application or use of the product.
At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine,
system, or other application or use.
The following are some examples of applications for which particu lar att ention must be given. This is not inten ded to be an exh austive list of all possible use s
of the products, nor is it intended to imply that the uses listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICA TION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR
THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PERFORMANCE DA TA
Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must corre late it to actual ap plication re quirement s. Actual per formance is subject to the OMRON Warranty
and Limitations of Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However,
some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRO N representative at any time to confirm actual specifications of purchased
products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and i s believed t o be accurate; however, no responsibility is assumed for clerical, typographical ,
or proofreading errors, or omissions.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user’s programming of a programmable product, or any consequence thereof.
COPYRIGHT AND COPY PERMISSION
This document shall not be copied for sales or promotions without permission. This document is protected by copyright and is intended solely for use in conjunction with the product. Please notify us before copying or reproducing this document in any m anner, for any other purpose. If copying or transmitting this
document to another, please copy or transmit it in its entirety.
RFID System
2
User's Manual
Introduction
Precautions for Safe Use
Be sure to observe the following precautions to ensure saf e use of the Products.
1. Do not use the Products in environments with flammable, explosive, or corrosive gasses.
2. Do not attempt to disassemble, repair, or modify any Product.
3. Tighten mounting screws securely.
4. Do not allow water or pieces of wire to enter from openings in the case. Doing so may cause fire or
electric shock.
5. Turn OFF the Controller power supply before mounting or removing an Antenna or Amplifier.
6. Turn OFF the power supply to the Controller before changing settings.
Attach a Setting switch protection Cover after setting Switch.
7. If a n error is detected in an y Product , immediately stop op eration and turn OFF the power su pply. Consult
with an OMRON representative.
8. Dispose of the Products as industrial waste.
9. Observe all warnings and precautions given in the body of this manual .
10. Do not install the Products near equipment that generates a large amount of heat, such as a heater,
transformer, or high-capacity resistor.
11.Because a cable has a locking mechanism, make sure that it has been locked before using the cable.
12.Do not open the back cover of the V680-H01-V2 antenna.
13.Do not touch the product immediately after usage at high temper atures . Doing so may occasionally result
in burning.
14.When using a V680-D1KP58HTN, Make sure that the sp lit pi n is installed co rrectl y to prevent the product
from becoming detached.
Introduction
RFID System
User's Manual
3
Introduction
Introduction
Precautions for Correct Use
Always observe the following precautions to prevent operation failures, malfunctions, and adverse effects on
performance and equipment.
1. Installation Environment
Do not use the Products in the following locations.
• Locations exposed to direct sunlight
• Locations exposed to corrosive gases, dust, metallic powder, or salts
• Locations not within the specified operating temperature range
• Locations subject to rapid changes in temperature or condensation
• Locations not within the specified humidity range
• Locations subject to direct vibration or shock outside the specified ranges
• Locations subject to spray of water, oil, or chemicals
• Locations subject to filled with steam
2. Installation
The Products communicate with RF Tags using the 13.56-MHz frequency band. Some motors, inverters, and switching po wer supplie s gener ate noise that can aff ect communications with th e RF Tags and
cause errors. If such de vices are located near t he RF Tags, always te st operat ion in adv ance to conf irm
whether the system will be affected.
• Observe the following precautions to minimize the effects of normal noise.
(1) Ground all metal objects in the vicinity of the Products to 100 Ω or less.
(2) Do not use the Products near high-voltage or high-current lines.
• Do not use non-waterproof Products in an environment where mist is present.
• Do not expose the Products to chemicals that adversely affect the Product materials.
• When mounting the Products, tighten the screws to the following torques.
Do not apply screw loctite and an y other organic solvent to any other parts than the screws.
The casing may get cracked.
V680-HS51: 6 N⋅m
V680-HS52: 40 N⋅m
V680-HS63: 1.2 N⋅m
V680-HS65: 1.2 N⋅m
V680-H01-V2: 1.2 N⋅m (Use the Mounting bracket of the attachment article.)
V680-D1KP52M-BT01: 24.5 N⋅m
V680-D1KP52M-BT11: 11 N⋅m
V680-D1KP66T/-D1KP66MT: 0.5 N⋅m
V680-D1KP66T-SP: 1.2 N⋅m
• Depending on the operating environment, the case surface may become fogged, but basic perfor-
mance will not be affected.
• Do not pull the Antenna connector over the power of 30 N.
The Antenna connector may be broken.
• If multiple Antennas are mounted near each other, communications performance may decrease due
to mutual interference. Refer to Installing Antennas on page 64 and check to make sure there is no
mutual interference.
• When Antenna(only V680-H01-V2) is used in the United States and Canada, the ferrite
core(ZCAT3035-1330) of the antenna's attachment is installed on controller's (V680-CA5D01-V@) DC
power cable.
• Transmission will not be possible if the front and back panels are mistakenly reversed and the Unit is
mounted to a metallic surface.
V680-D1KP66MT
• The transmission distance will be reduced when the Unit is not mounted to a metallic surface.
V680-D1KP66MT
RFID System
4
User's Manual
Introduction
• The maximum communications distance can be obtained when the Antenna faces the RF tag directly.
When the Tag is installed at a tilt, the communications distance is reduced. Consider the effect of the
Tag at a tilt when installing the Tag.
• Provide the mounting distances between plural RF tags to prevent them from malfunctions due to
mutual interference.
• If the central axis of an antenna and RF tag shifts, a communications distance will fall.
3. Storage
Do not store the Products in the following locations.
• Locations exposed to direct sunlight
• Locations exposed to corrosive gases, dust, metallic powder, or salts
• Locations not within the specified storage temperature range
• Locations subject to rapid changes in temperature or condensation
• Locations not within the specified storage humidity range
• Locations subject to direct vibration or shock outside the specified ranges
• Locations subject to spray of water, oil, or chemicals
• Locations subject to filled with steam
Introduction
4. Cleaning
• Do not clean the Products with paint thinner or the equivalent. Paint thinner, benzene, acetone, and
kerosene or the equivalent will dissolve the resin materials and case coating.
5. Combination of the Amplifier
• With the amplifierV680-HA63A use only the RF tags of V680-D1KP52MT, V680-D1KP52M-BT01,
V680-D1KP52M-BT11, V680-D1KP53M, V680-D1KP54T, V680-D1KP66T, V680-D1KP66MT, V680D1KP66T-SP, or V680-D1KP58HTN. Do not use these RF T ags together with the V680-HA63B Amplifier.
6. Use at high temperatures (V680-D1KP58HTN)
• Data stored in memor y in the RF Tag may be lost due to the characteristics of EEPROM, if the accu-
mulated usage time of the RF Tag at a high temperature over 125°C exceeds 10 hours after writing
data to the RF Tag.
• Do not communicate between the Antenna and the RF Tag in an environment where the ambient
operating temperature is 85°C or higher.
An error in communications between the Antenna and the RF Tag may occur.
• Do not use the commands using UID (unique identification number for each RF Tag) when the RF tag
is used at a high temperature over 125°C. The UID may be lost due to the characteristics of
EEPROM.
•Do not use the READ ID command (command code: ID).
•Do not make the UID Addition Setting (command code: US).
•Communications specifications (FIFO trigger, FIFO repeat, multi-access trigger, multi-access repeat,
and selective) can not be used.
For Use at high temperatures, refer to RF T ags - Use at high temperatures (V680-D1KP58HTN) in Section 2 Specifica-
tions and Performance.
p.40
RFID System
User's Manual
5
Introduction
Introduction
Meanings of Symbols
Meanings of Symbols
Indicates particularly important points related to a function, including precautions and application advice.
Indicates page numbers containing relevant information.
RFID System
6
User's Manual
Introduction
Table of Contents
Introduction
Precautions for Safe Use 3
Precautions for Correct Use 4
Meanings of Symbols 6
Table of Contents 7
Section 1 Product Overview 9
Features 10
Product Configuration 11
Section 2 Specifications and Performance 13
Introduction
Antennas with Separate Amplifier 14
Antennas with Built-in Amplifier 21
Amplifier 26
RF Tags 29
Section 3 Communications Specifications 45
Communications Distances 46
Communication Time (Reference) 60
Section 4 Installation 63
Installing Antennas 64
Mounting Amplifiers 73
Installing RF Tags 75
Section 5 Chemical Resistance 95
Chemical Resistance of the Antennas 96
Chemical Resistance of RF Tags 97
Degree of Protection 101
Revision History 104
RFID System
User's Manual
7
Introduction
Introduction
MEMO
RFID System
8
User's Manual
Section 1 Product Overview
Features 10
Product Configuration 11
Section 1 Product Overview
RFID System
User's Manual
9
Section 1
Product Overview
Features
Section 1 Features
The V680-series RFID System actively supports many different types of system, such as distributed-control
systems and many-product, small-lot production systems, with non-contact data communications using
electromagnetic induction.
Non-contact Data Communications
The V680 Series uses electromagnetic induction to enable non-contact, bi-directional data communications between Antennas and RF Tags.
EEPROM Memory
EEPROM (non-volatile memory) is used for RF Tag memory. No battery is required, so there is no
need to be concerned about battery service life.
CRC Used for Transmission Error Detection
A bi-directional 16-bit CRC (Cyclic Redundancy Chec k) ha s been a dd ed a s th e err or de te ct ion me th od
for wire transmissions between ID Controllers and Antennas, and for wireless transmissions between
Antennas and RF Tags. This method maintains superior communications reliability even where problems such as noise occur.
1,000byte of Memory
RF Tags have 1,000byte of memory. In addition to the ID data required on-site, data such as model
numbers and inspection information can be input.
100,000 Data Rewrites at Normal Temperatures
When the RF Tag is used at temperatures of up to 25°C, each block of EEPROM data can be rewritten
up to 100,000 times (in units of single block, 8-bytes).
Superior Environmental Resistance and High Reliability
Antennas and RF Tags now have greater environmental resistance and are not affected by vibration,
oil, or water.
10
RFID System
User's Manual
Product Configuration
Section 1
Product Overview
A V680-series RFID System consists of an ID Controller, one or more Amplifiers, one or two Antennas, and
RF Tags. Select the models suitable for the application.
Using Antennas with Separate Amplifiers
Host device
ID Controller
Personal computer Programmable Controller
RS-232C
RS-422 RS-485
V680-CA5D01-VV680-CA5D02-V CS1W-V680C11/12 CJ1W-V680C11/12
ID Sensor Units
V680-HA63A
(SYSMAC CS/CJ Series)
㪭
㪭
㪍
㪍
㪏㪇
㪏㪇
㪚
㪚
㪈
㪈
㪈
㪉
㪩
㪩
㪬
㪬
㪥
㪥
㪜
㪜
㪩
㪩
㪚
㪚
㪟
㪜㪘
㪛
㪜
㪜
㪈
㪩
㪩
㪧
㪧
㪫
㪫
㪆
㪆
㪥㪦㪩㪤㪆㪜㪩㪩
㪥㪦㪩㪤㪆㪜㪩㪩
㪜
㪜
㪩
㪩
㪩
㪩
㪟
㪟
㪟
㪜
㪘㪛
㪫
㪉
㪆
㪩
㪥㪦㪩㪤㪆㪜㪩㪩
㪫
㪫
㪜㪪
㪜
㪪
㪫
㪫
㪦
㪦
㪥
㪥
㪟
㪟
㪜
㪜
㪘㪛
㪘
㪛
㪈
㪈
㪛
㪟
㪚
㪜
㪉㪋
㪘
㪭
㪛
㪠㪥
㪉
㪧
㪬
㪫
㪂
㪄
Section 1 Product Configuration
Amplifiers
V680-HS51 V680-HS52 V680-HS63 V680-HS65
Antennas with Separate
Amplifier
V680-D1KP52MT V680-D1KP53M V680-D1KP66T-SPV680-D1KP54TV680-D1KP52MT-BT01/
-D1KP52MT-BT11
V680-D1KP66T/
-D1KP66MT
V680-D1KP58HTN
RF T ags
When embedding the V680-D1KP52MT and V680-D1KP53M into a metal surface, use the V680-HS51, V680-HS52 Antenna.
Transmission will not be possible if the V680-HS63 Antenna is used.
Use the V680-D1KP52MT, V680-D1KP52M-BT01, V680-D1KP52M-BT11, V680-D1KP53M, V680-D1KP54T, V680-D1KP66T,
V680-D1KP66MT, C680-D1KP66T-SP, and V680-D1KP58HTN RF Tags in combination with only the V680-HA63A Amplifier, Do
not use these RF Tags together with the V680-HA63B Amplifier.
RFID System
User's Manual
11
Section 1 Product Configuration
RS-232C
CS1W-V680C11
V
6
8
0
C
1
1
R
U
N
E
R
C
T
/R
NORM/
ERR
E
R
P
E
R
H
T
E
S
T
O
N
H
E
A
D
1
CJ1W-V680C11
RS-422
RS-485
V680-H01-V2
* Always use the specified Cable to connect a
V680-H01-V2 Antenna. The V680-H01-V2
Antenna cannot be connected without using
the specified Cable.
Host device
Programmable Controller
(SYSMAC CS/CJ Series)
ID Controller
ID Sensor Units
Cable
Antennas with Built-in
Amplifier
RF T ags
V700-A40-W M
V680-CA5D01-V
Personal computer
V680-D1KP58HTN V680-D1KP66T
* When V680-H01-V2 is connected with
V680-CA1D/-CA2D, V680-D1KP66T cannot
be used.
Section 1
Product Overview
Using a V680-H01-V2 Antenna with Built-in Amplifier
12
RFID System
User's Manual
Section 2 Specifications and Performance
Antennas with Separate Amplifier 14
Antennas with Built-in Amplifier 21
Amplifier 26
RF Tags 29
Section 2 Specifications and Performance
RFID System
User's Manual
13
Section 2 Antennas with Separate Amplifier
Case material Brass
Communications
surface
ABS resin
Filling resin Epoxy resin
Cable PVC (black)
Section 2
Specifications and Performance
Antennas with Separate Amplifier
V680-HS51
General Specifications
Item Model V680-HS51
Ambient operating
temperature
Ambient storage
temperature
Ambient operating
humidity
Insulation resistance 20 MΩ min. (at 500 VDC) between connector terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case
Degree of protection IP67.(IEC60529)
Dielectric strength
Shock resistance
Dimensions M12 × 35 mm
Material ABS resin, brass, and epoxy resin filler
Weight Approx. 55 g
Cable length Standard lengths of 2 m
-10 to 60°C (with no icing)
-25 to 75°C (with no icing)
35% to 95% (with no condensation)
Oil resistance equivalent to IP67g according to the former JEM standard.
Note: The connectors are not waterproof.
10 to 2,000 Hz, 1.5-mm double amplitude, acceleration: 150 m/s
tions (up/down, left/right, and forward/backward) for 15 minutes each
2
1,000 m/s
, 3 times each in 6 directions (Total: 18 times)
2
, 10 sweeps in each of 3 axis direc-
Dimensions
• V680-HS51
12.5 dia.
Mounting Hole Dimensions
21 dia.
17
M12 × 1
9.6 dia.
(Unit : mm)
Toothed washer
Connector
(14.5 dia.)
Insulation cover
(16.8 dia.)
25
Ferrite core
26.2
50
Two lock nuts
12
7
24
33
35
Coaxial cable, 2.9 dia.,
standard length: 2 m
15
14
RFID System
User's Manual
Specifications and Performance
Case material Brass
Communications
surface
ABS resin
Filling resin Epoxy resin
Cable PVC (gray)
V680-HS52
General Specifications
Item Model V680-HS52-W
(Standard cable, waterproof connector)
Ambient operating
temperature
Ambient storage
temperature
Ambient operating
humidity
Insulation resistance 20 MΩ min. (at 500 VDC) between connector terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case
Degree of protection IP67.(IEC60529)
Dielectric strength
Shock resistance
Dimensions M22 × 65 mm
Material ABS resin, brass, and epoxy resin filler
Weight Approx. 850 g (with 12.5 m cable)
Cable length Standard lengths of 2 and 12.5 m
-10 to 60°C (with no icing)
-25 to 75°C (with no icing)
35% to 95% (with no condensation)
Oil resistance equivalent to IP67g according to the
former JEM standard.
Note: The connector specifications are IP67 and
IP65.(IEC60529)
10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s
(up/down, left/right, and forward/backward) for 8 minutes each
2
500 m/s
, 3 times each in 6 directions (Total: 18 times)
(Flexible cable, non-waterproof connector)
IP67.(IEC60529)
Oil resistance equivalent to IP67g according to the
former JEM standard.
Note: The connectors are not waterproof.
Section 2
V680-HS52-R
2
, 10 sweeps in each of 3 axis directions
Section 2 Antennas with Separate Amplifier
Dimensions
• V680-HS52-W
22.5 dia.
Mounting Hole Dimensions
Antenna
35 dia.
19.8 dia.
Two toothed washers
Two lock nuts
M22 × 1
16.5 dia.
Ferrite core
5030
37
Connector
16.5 dia.
14.5 dia.
Insulation cover
Operation indicator
730
47.6
50
57
65
Coaxial cable, 5.5 dia.,
standard length: 2 m
RFID System
User's Manual
15
Section 2
Case material Brass
Communications
surface
ABS resin
Filling resin Epoxy resin
Cable PVC (black)
Specifications and Performance
• V680-HS52-R
Section 2 Antennas with Separate Amplifier
22.5 dia.
Mounting Hole Dimensions
Antenna
35 dia.
19.8 dia.
Two toothed washers
Two lock nuts
M22 × 1
16.5 dia.
Ferrite core
(39.5)
5030
Insulation cover
Connector
14.5 dia.
Insulation cover
16.5 dia.
Operation indicator
730
47.6
50
57
65
Coaxial cable, 5.3 dia.,
standard length: 2 m
16
RFID System
User's Manual
V680-HS63
(Unit: mm)
23
5
5
Operation indicator
40
28±0.1
53
27 6
11
Note: Mounting Hole Dimensions
Coil center
Two, M4 or 4.5 dia. holes
37
5030
16.5 dia.
Coaxial cable, 5.5 dia.,
standard length: 2 m
Connector
Ferrite core
Insulation cover
16.5 dia.
14.5 dia.
Antenna
Case material ABS resin
Filling resin Epoxy resin
Cable PVC (gray)
General Specifications
Item Model V680-HS63-W
(Standard cable, waterproof connector)
Ambient operating
temperature
Ambient storage
temperature
Ambient operating
humidity
Insulation resistance 20 MΩ min. (at 500 VDC) between cable terminals and case
Dielectric strength 1,000 VAC, 50/60Hz for 1 min between cable terminals and case
Degree of protection IP67.(IEC60529)
Vibration resistance 10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s
Shock resistance 500 m/s
Dimensions 40 × 53 × 23 mm
Material ABS resin case, epoxy resin filler
Weight Approx. 850 g (with 12.5 m cable)
Cable length Standard lengths of 2 and 12.5 m
-10 to 60°C (with no icing)
-25 to 75°C (with no icing)
35% to 95% (with no condensation)
IP67.(IEC60529)
Oil resistance equivalent to IP67g according to the
former JEM standard.
Note: The connector specifications are IP67 and
IP65.(IEC60529)
(up/down, left/right, and forward/backward) for 11 minutes each
2
, 3 times each in 6 directions (Total: 18 times)
Oil resistance equivalent to IP67g according to the
former JEM standard.
Note: The connectors are not waterproof.
Section 2
Specifications and Performance
V680-HS63-R
(Flexible cable, non-waterproof connector)
2
, 10 sweeps in each of 3 axis directions
Section 2 Antennas with Separate Amplifier
Dimensions
• V680-HS63-W
RFID System
User's Manual
17
Section 2
Case material ABS resin
Filling resin Epoxy resin
Cable PVC (black)
Specifications and Performance
• V680-HS63-R
Antenna
Ferrite core
(39.5)
Connector
(Unit: mm)
Section 2 Antennas with Separate Amplifier
40
28±0.1
5
5
Operation indicator
23
Note: Mounting Hole Dimensions
Coil center
27 6
53
11
Two, M4 or 4.5 dia. holes
16.5 dia.
5030
Coaxial cable, 5.3 dia.,
standard length: 2 m
14.5 dia.
16.5 dia.
Insulation cover
18
RFID System
User's Manual
Specifications and Performance
Operation indicator
30
20
11
(Unit: mm)
16.5 dia.
14.5 dia.
37
5030
16.5 dia.
Coaxial cable, 5.5 dia.,
standard length: 2 m
Connector
Ferrite core
Insulation cover
14
10
10
Bushing
50
25
100
90±0.25
50
100
90±0.2 5
4-4.5 dia.
(Mounting holes)
Case material ABS resin
Filling resin Epoxy resin
Cable PVC (gray)
V680-HS65
General Specifications
Item Model V680-HS65-W
(Standard cable, waterproof connector)
Ambient operating
temperature
Ambient storage
temperature
Ambient operating
humidity
Insulation resistance 20 MΩ min. (at 500 VDC) between connector terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case
Degree of protection IP67 (IEC60529)
Dielectric strength
Shock resistance
Dimensions 100 × 100 × 30 mm
Material ABS resin case, epoxy resin filler
Weight Approx. 1100 g (with 12.5 m cable)
Cable length Standard lengths of 2 and 12.5 m
−25 to 70°C (with no icing)
−40 to 85°C (with no icing)
35% to 95% (with no condensation)
Oil resistance equivalent to IP67g according to the
former JEM standard.
Note: The connector specifications are IP67 and
IP65 (IEC 60529).
10 to 500 Hz, 1.5-mm double amplitude, acceleration: 100 m/s
(up/down, left/right, and forward/backward) for 11 minutes each
2
500 m/s
, 3 times each in 6 directions (Total: 18 times)
(Flexible cable, non-waterproof connector)
IP67 (IEC60529)
Oil resistance equivalent to IP67g according to the
former JEM standard.
Note: The connectors are not waterproof.
Section 2
V680-HS65-R
2
, 10 sweeps in each of 3 axis directions
Section 2 Antennas with Separate Amplifier
Dimensions
• V680-HS65-W
RFID System
User's Manual
19
Section 2 Antennas with Separate Amplifier
(39.5)
16.5 dia.
14.5 dia.
(Unit: mm)
5030
16.5 dia.
Coaxial cable, 5.3 dia.,
standard length: 2 m
Insulation cover
Connector
Ferrite core
Operation indicator
30
20
11
14
10
10
Bushing
50
25
100
90±0.25
50
100
90±0.2 5
4-4.5 dia.
(Mounting holes)
Case material ABS resin
Filling resin Epoxy resin
Cable PVC (black)
Section 2
Specifications and Performance
• V680-HS65-R
RFID System
20
User's Manual
Antennas with Built-in Amplifier
V680-H01-V2
General Specifications
Item Model V680-H01-V2
Ambient operating
temperature
Ambient storage
temperature
Ambient operating
humidity
Insulation resistance 20 MΩ min. (at 100 VDC) between connector terminals and the rear plate
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and the rear plate
Degree of protection IP63.(IEC60529); Mounting direction: Communications surface facing up
Dielectric strength
Shock resistance
Cable length 0.5 m (use an relay cable to connect to the Controller up to 30.5 m)
LED indicators RUN, COMM, NORM, ERR, CNT-TYPE, TAG-TYPE, Error Code, Level
Weight Approx. 900 g
-10 to 55°C (with no icing)
-35 to 65°C (with no icing)
35% to 85% (with no condensation)
10 to 150 Hz, 0.35-mm single amplitude, acceleration: 50 m/s
(up/down, left/right, and forward/backward) for 8 minutes each
2
150 m/s
, 3 times each in 6 directions (Total: 18 times)
Section 2
Specifications and Performance
2
, 10 sweeps in each of 3 axis directions
Section 2 Antennas with Built-in Amplifier
Communications Specifications
Item Model V680-H01-V2
Communications method Electromagnetic induction
Operating frequency 13.56 MHz ± 7KHz
Modulation ASK
RFID System
User's Manual
21
Section 2
Case material PC/ASA resin
Rear Panel Aluminum
Cable PVC
Specifications and Performance
Dimensions
MOUNTING SCREW HOLES
Senter of Coil
Section 2 Antennas with Built-in Amplifier
142.5
±0.2
235
65
(25-dia.)
50
Setting switch protection Cover
185±0.2
Four, M4 or 4.5-dia. holes
Twelve, Operation Indicator
Communications sufrace
200
185
Four, Mounting bracket
Vinyl Insulated Round Cord (5.8-dia.)
(41/0.16-dia.) 2 Cores (17/0.08-dia.) 8 Cores
Standard Length 0.5 m
Four, 5-dia. holes
(Mounting Holes)
6
30 38
142.5
235
250
7.5
(17)
(Unit : mm)
Connector
Ferrite Core
14 64.8
+50
500 0 (45)
20-dia.
(1)40
13.5
22
RFID System
User's Manual
Operation Indicator
name Color Meaning
RUN Green Lit when the power is ON.
COMM Yellow Lit when a command is being sent.
NORM Green Lit when communications with a RF Tag are normal in Normal Communications
ERR Red Lit when an error occurs in communications with a RF Tag in Normal
CNT-TYPE Yellow Lit when in V680-CA1D/-CA2D Controller connection mode (SW1-1 setting: ON).
TAG-TYPE Yellow Lit when in V680-D@KF@@ RF Tag mode (SW1-2 setting: ON).
LV6/7D Yellow Maintenance Mode: Lit at distance or speed level 6.
LV5/7A Yellow Maintenance Mode: Lit at distance or speed level 5 or higher.
LV4/76 Yellow Maintenance Mode: Lit at distance or speed level 4 or higher.
LV3/72 Yellow Maintenance Mode: Lit at distance or speed level 3 or higher.
LV2/71 Yellow Maintenance Mode: Lit at distance or speed level 2 or higher.
LV1/70 Yellow Maintenance Mode: Lit at distance or speed level 1 or higher.
Section 2
Specifications and Performance
Mode.
Section 2 Antennas with Built-in Amplifier
Communications Mode.
Normal Communications Mode: Lit when a write protection error occurs.
Normal Communications Mode: Lit when an address error occurs.
Normal Communications Mode: Lit when a RF Tag memory error occurs.
Normal Communications Mode: Lit when a no RF Tag error occurs.
Normal Communications Mode: Lit when a verification error occurs.
Normal Communications Mode: Lit when a RF Tag communications error occurs.
The distance level will vary greatly depending on the surrounding environment. The setting position will serve as a
guide, but use RUN mode to conduct a sufficient number of tests in the actual operating environment.
Values of distance level 6 may not be displayed, but this will not affect the RUN mode performance and does not indicate a malfunction.
Differences between the V680-H01 and the V680-H01-V2
As shown in the following table, the V680-H01-V2 provides additional indicators.
Turn ON SW1-1(Antenna) when using the V680-CA1D/CA2D.
Only when the V680-D1KP58HTN is used, it is possible to set it.
display functions
RUN (POWER/COMM) OK OK OK
COMM (POWER/COMM) OK OK OK
NORM OK NO NO
ERR OK NO NO
CNT-TYPE OK OK NO
TAG-TYPE --- --- --LV6/7D OK NO NO
LV5/7A OK NO NO
LV4/76 OK NO NO
LV3/72 OK NO NO
LV2/71 OK NO NO
LV1/70 OK NO NO
SW1-1: OFF SW1-1: ON no switch
V680-H01-V2 V680-H01
RFID System
User's Manual
23
Section 2
Note: Please attach a setting switch protection cover after setting switch.
Specifications and Performance
Setting Switch
Section 2 Antennas with Built-in Amplifier
Setting switch protection cover
Setting Function Default setting
SW1-1 Controller selection
OFF:V680-CA5D01-V@, CS1W-V680C11, or CJ1W-V680C11
ON: V680-CA1D/-CA2D
SW1-2 RF Tag selection
OFF:V680-D1KP@@ (EEPEOM RF Tags)
ON: V680-D@KF@@ (FRAM RF Tags)
SW1-3 Reserved by System (Always set this Switch to OFF.) --SW1-4 Reserved by System (Always set this Switch to OFF.) ---
Note: Only when the V680-D1KP58HTN is used, it is possible to connect it with the V680-CA1D/-CA2D.
When the V680-CA5D01-V@, CS1W-V680-C11 and CJ1W-V680C11 is used, set SW1-1 of the antenna to turning off.
See Note.
OFF
OFF
Set SW1-1 on the V680-H01-V2 Antenna and the Controller as shown in the following table.
When the V680-CA1D/-CA2D is used, set SW1-1 of the antenna to turning on.
When using it excluding the V680-CA1D/-CA2D, set SW1-1 of the antenna to turning off besides.
Antenna setting Controller setting
V680-H01-V2 V680-CA5D01-V@ CS1W-V680C11
CJ1W-V680C11
SW1-1: OFF SW4-8: OFF DM20000 + 100 × m+3=0000
SW1-1: ON SW4-8: ON
: Cannot be used.
: Can be used.(Controller setting not required.)
Note: The high-speed mode cannot be used by the controller's setting.
Differences between the V680-H01 and the V680-H01-V2
As shown in the following table, the V680-H01-V2 supports additional maintenance functions.
Turn ON SW1-1(Antenna) when using the V680-CA1D/CA2D.
Only when the V680-D1KP58HTN is used, it is possible to set it.
display functions
Communication Test Mode OK OK OK
Noise Level Measurement
Mode
Distance Level Measurement
Mode
Speed Level Measurement
Mode
Communications Success
Rate Measurement Mode
See Note.
DM20000 + 100 × m+3=0001
V680-H01-V2 V680-H01
SW1-1: OFF SW1-1: ON no switch
OK NO NO
OK NO NO
OK NO NO
OK NO NO
See Note. Å@See Note.
V680-CA1D
V680-CA2D
24
RFID System
User's Manual
Section 2
Connector (Antenna end))
Connector (Controller end))
Connection label
Vinyl Insulated Round Cord
6 dia.
20 dia.
41.8
L1
±100
49
(Unit: mm)
15 dia.
Cable PVC
Specifications and Performance
Cables (V680-H01-V2 exclusive use)
Specifications
Item Model V700-A40-W
Number of conductors 10
Insulation resistance 5 MΩ min. (at 500 VDC) between terminals and sheath
Dielectric strength 500 VAC, 1 min
Dimensions
Item Model V700-A40-W 2M V700-A40-W 5M V700-A40-W 10M V700-A40-W 20M V700-A40-W 30M
Length (L1) Approx.2m Approx. 5 m Approx.10m Approx. 20 m Approx. 30 m
Weight Approx. 150 g Approx.360 g Approx. 700 g Approx.1,350 g Approx.2,000 g
L1 2,000 5,000 10,000 20,000 30,000
Section 2 Antennas with Built-in Amplifier
RFID System
User's Manual
25
Section 2 Amplifier
Operation indicator
13.7 65 18
51
36
15 dia.
40
25
9.5 dia.
25
3.5
12.8 dia.
15 35.6
25
Round, vinyl-insulated cable (5.8 dia.), standard length: 5 m,
(41/0.16 dia) 2 conductors, (17/0.08 dia.) 8 conductors
Connector
Connector
Case material PC resin
Cable PVC
Section 2
Specifications and Performance
Amplifier
V680-HA63A
General Specifications
Item Model V680-HA63A
Ambient operating
temperature
Ambient storage
temperature
Ambient operating
humidity
Insulation resistance 20 MΩ min. (at 500 VDC) between cable terminals and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between cable terminals and case.
Degree of protection IP67, IP65 (IEC 60529)
Dielectric strength
Shock resistance 500 m/s
Dimensions 25 × 40 × 65 mm (Not including protrusions.)
Materials PC
Weight Approx. 650 g (with 10 m cable)
Cable length Standard lengths of 5 and 10 m
Note: The maximum total cable extension is 50 m (including the Amplifier cable). A maximum of two extension cables can be
connected.
-10 to 55°C (with no icing)
-25 to 65°C (with no icing)
35% to 85% (with no condensation)
Note: Not including connector at Controller end.
(When V680-HS52-W, V680-HS63-W, and V680-HS65-W
is connected)
10 to 500 Hz, 1.5-mm double amplitude, acceleration:100 m/s
(up/down, left/right, and forward/backward) for 11 minutes each
2
, 3 times each in 6 directions (Total: 18 times)
IP40 (IEC 60529)
(When V680-HS51, V680-HS52-R, V680HS63-R, and V680-HS65-R is connected)
2
, 10 sweeps in each of 3 axis directions
Dimensions
26
RFID System
User's Manual
Nomenclature
Section 2
Specifications and Performance
Antenna with Separate Amplifier connection port
RUN
COMM
NORM
ERR
LV6/7D
LV5/7A
LV4/76
LV3/72
Operation indicators
LV2/71
LV1/70
Controller connector
Antenna Connection Port
The Antenna connection port is connected a V680-series Antenna.
Controller Connector
The Controller connector is connected to Antenna connection port on the Controller.
Section 2 Amplifier
Operation Indicators (LEDs)
Name Color Meaning
RUN Green Lit when the power is ON.
COMM Yellow Lit when a command is being sent.
NORM Green Lit when communications with a RF Tag are normal in Normal Communications Mode.
ERR Red Lit when an error occurs in communications with a RF Tag in Normal Communications Mode.
LV6/7D Yellow
LV5/7A Yellow
LV4/76 Yellow
LV3/72 Yellow
LV2/71 Yellow
LV1/70 Yellow
The distance level will vary greatly depending on the surrounding environment. The setting position will serve as a
guide, but use RUN mode to conduct a sufficient number of tests in the actual operating environment.
Values of distance level 4 or above may not be displayed, but this will not affect the RUN mode performance and does
not indicate a malfunction.
Maintenance Mode: Lit at distance or speed level 6.
Normal Communications Mode: Lit when a write protection error occurs.
Maintenance Mode: Lit at distance or speed level 5 or higher.
Normal Communications Mode: Lit when an address error occurs.
Maintenance Mode: Lit at distance or speed level 4 or higher.
Normal Communications Mode: Lit when a RF Tag memory error occurs.
Maintenance Mode: Lit at distance or speed level 3 or higher.
Normal Communications Mode: Lit when a no RF Tag error occurs.
Maintenance Mode: Lit at distance or speed level 2 or higher.
Normal Communications Mode: Lit when a verification error occurs.
Maintenance Mode: Lit at distance or speed level 1 or higher.
Normal Communications Mode: Lit when a RF Tag communications error occurs.
RFID System
User's Manual
27
Section 2 Amplifier
51 L1
±100
49
15.5 dia.
Connector (Controller end))
Connection label
Connector (Amplifier end)
6 dia.
15 dia.
(Unit: mm)
Cable PVC
Section 2
Specifications and Performance
Cables (V680-HA63 exc lusive use)
Specifications
Item Model V700-A43/V700-A44
Number of conductors 10
Insulation resistance 5 MΩ min. (at 500 VDC) between terminals and sheath
Dielectric strength 500 VAC, 1 min
Dimensions
Item Model V700-A43 V700-A44
Length (L1) Approx.10m Approx. 20 m
Weight Approx. 700 g Approx.1,350 g
28
RFID System
User's Manual
Loading...