CIDRW SYSTEM
V640 SERIES
USER'S MANUAL
AMPLIFIER UNITS
V640-HAM11-ETN
V640-HAM11-L-ETN
CIDRW HEADS
V640-HS61
V640-HS62
Cat. No. Z308-E1-02
Introduction
Thank you for purchasing the V640-series CIDRW System.
Please observe the following points when operating the V640-series CIDRW System:
• Allow the CIDRW System to be installed and operated only by qualified specialist with a sufficient knowledge
of electrical systems.
• Please read and understand the contents of this manual before using the system.
• After reading this manual, store it in a convenient location for easy reference whenever necessary.
Introduction
SECTION 1
SECTION 2
SECTION 3
SECTION 4
SECTION 5
SECTION 6
SECTION 7
Table of Contents/Precautions in Using the Products
Product Outline
Installation and Connections/Wiring
Preparing for Communications
Reading from/Writing to ID Tags
Browser Interface
INTRODUCTION
ÇÕǹÇ?Ç ëÊ 1 èÕ ëÊ 2 èÕ ëÊ 3 èÕ ëÊ 4 èÕ
SECTION 1 SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION 6 SECTION 7
Troubleshooting
Appendix
CIDRW System
V640-HAM11-ETN Amplifier Unit
V640-HAM11-L-ETN Amplifier Unit
V640-HS61 CIDRW Head
V640-HS62 CIDRW Head
User's Manual
INTRODUCTION
INTRODUCTION
READ AND UNDERSTAND THIS DOCUMENT
Please read and understand this document before using the products. Please consult your OMRON representative if you
have any questions or comments.
Precautions in using the product
WARRANTY
OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one
year (or other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NONINFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY
BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is
asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE
PRODUCTS UNLESS OMRON’S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED,
STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR
INAPPROPRIATE MODIFICATION OR REPAIR.
SUITABILITY FOR USE
THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR
RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT
OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for OMRON's safety rated
products.
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of
products in the customer’s application or use of the product.
At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and
limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the
suitability of the products in combination with the end product, machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an
exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the
products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not
described in this document.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment,
amusement machines, vehicles, safety equipment, and installations subject to separate industry or government
regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY
WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND
THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
CIDRW System
2
User’s Manual
INTRODUCTION
PERFORMANCE DATA
Performance data given in this document is provided as a guide for the user in determining suitability and does not
constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual
application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant
construction changes are made. However, some specifications of the product may be changed without any notice. When
in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your
request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased
products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are
shown.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical, or proofreading errors, or omissions.
INTRODUCTION
Precautions in using the product
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user’s programming of a programmable product, or any consequence thereof.
COPYRIGHT AND COPY PERMISSION
This document shall not be copied for sales or promotions without permission.
This document is protected by copyright and is intended solely for use in conjunction with the product. Please notify us
before copying or reproducing this document in any manner, for any other purpose. If copying or transmitting this
document to another, please copy or transmit it in its entirety.
CIDRW System
User’s Manual
3
INTRODUCTION
INTRODUCTION
Applicable Standards
Precautions in using the product
The CIDRW System complies with the following international regulations and standards.
1. USA
Amplifier Unit CIDRW Head
FCC Part 15 Subpart C
FCC ID: E4EV640HAM11
FCC Part 15 Subpart C
FCC ID: E4EV640HAM11L
FCC NOTICE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired opera-
tion.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Do not remove the ferrite core (TDK-EPC Type ZCAT2749-0430C:V640-HS62) installed on the cables to suppress RF
interference.
FCC Part15 subpart B
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
V640-HAM11-ETN V640-HS61
V640-HAM11-L-ETN V640-HS62
CAUTION
This device must be professionally installed.
CIDRW System
4
User’s Manual
2. Europe
(Radio and Telecommunications Terminal Equipment Directive 1999/5/EC) V640-HAM11-ETN V640-HS61
Radio:
EMC:
Safety:
EN 300 330-2
EN 301 489-1
EN 301 489-3
EN 61010-1
INTRODUCTION
INTRODUCTION
Amplifier Unit CIDRW Head
Precautions in using the product
V640-HAM11-L-ETN V640-HS62
English Hereby, Omron, declares that this V640-HAM11-ETN / V640-HAM11-L-ETN is in compliance with the essential requirements and other rel-
Finnish Omron vakuuttaa täten että V640-HAM11-ETN / V640-HAM11-L-ETN tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
Dutch Hierbij verklaart Omron dat het toestel V640-HAM11-ETN / V640-HAM11-L-ETN in overeenstemming is met de essentiële eisen en de
French Par la présente Omron déclare que lappareil V640-HAM11-ETN / V640-HAM11-L-ETN est conforme aux exigences essentielles et aux
Swedish Härmed intygar Omron att denna V640-HAM11-ETN / V640-HAM11-L-ETN stär l överensstämmelse med de väsentliga egenskapskrav och
Danish Undertegnede Omron erklærer herved, at følgende udstyr V640-HAM11-ETN / V640-HAM11-L-ETN overholder de væsentlige krav og
German Hiermit erklärt Omron, dass sich dieser/diese/dieses V640-HAM11-ETN / V640-HAM11-L-ETN in Übereinstimmung mit den grundlegenden
Greek
Italian Con la presente Omron dichiara che questo V640-HAM11-ETN / V640-HAM11-L-ETN é conforme ai requisiti essenziali ed alle altre dispo-
Spanish Por medio de la presente Omron declara que el V640-HAM11-ETN / V640-HAM11-L-ETN cumple con los requisitos esenciales y cuales-
Portuguese
3. Canada
IC ID: 850J-V64HAM11 V640-HAM11-ETN V640-HS61
IC ID: 850J-V64HM11L V640-HAM11-L-ETN V640-HS62
evant provisions of
Directive 1999/5/EC.
sitä koskevien direktiivin muiden ehtojen mukainen.
andere relevante bepalingen van richtlijh 1999/5/EG.
autres dispositions pertinentes de la directive 1999/5/CE.
övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
øvrige relevante krav i direktiv 1999/5/EF.
Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi)
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Omron ΔΗΛΩΝΕΙ ΟΤΙV640-HAM11-ETN / V640-HAM11-L-ETN
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙ Σ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
sizioni pertinenti stabilite dalla direttiva 1999/5/CE.
quiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Omron declara que este V640-HAM11-ETN / V640-HAM11-L-ETN est conforme com os tequisitos essenciais e outras disposições da
Directiva 1999/5/CE.
Amplifier Unit CIDRW Head
This device complies with RSS-Gen of IC (Industry Canada) Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
ICES-003
This class A digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada.
CIDRW System
User’s Manual
5
INTRODUCTION
INTRODUCTION
4. China
Amplifier Unit CIDRW Head
Precautions in using the product
CMIIT ID: 2010DJ5964 V640-HAM11-ETN V640-HS61
CMIIT ID: 2010DJ5965 V640-HAM11-L-ETN V640-HS62
5. Korea
6. Taiwan
Amplifier Unit CIDRW Head
OMR-V640-HAM11-ETN V640-HAM11-ETN V640-HS61
OMR-V640-HAM11-L-E V640-HAM11-L-ETN V640-HS62
Amplifier Unit CIDRW Head
CCAB10LP461AT0 V640-HAM11-ETN V640-HS61
CCAB10LP462AT3 V640-HAM11-L-ETN V640-HS62
7. Singapore
Amplifier Unit CIDRW Head
N2294-10 V640-HAM11-ETN V640-HS61
V640-HAM11-L-ETN V640-HS62
CIDRW System
6
User’s Manual
INTRODUCTION
Safety Precautions
WARNING
WARNING
● Definition of Precautionary Information
The following notation and alert symbols are used in this User's Manual to provide precautions required to
ensure safe usage of a V640-series CIDRW System. The safety precautions that are provided are extremely
important to safety. Always read and heed the information provided in all safety precautions.
The following signal words are used in this manual.
Indicates a potentially hazardous situation which, if not avoided, will result in minor or
moderate injury, or may result in serious injury or death. Additionally there may be significant property damage.
● Meanings of Alert Symbols
INTRODUCTION
Precautions in using the product
Prohibition
Indicates general prohibitions for which there is no specific symbol.
● Alert Statements in this Manual
The product is not designed or rated for ensuring the safety of persons.
Do not use it for such purposes.
CIDRW System
User’s Manual
7
INTRODUCTION
Precautions for Safe Use
INTRODUCTION
Precautions in using the product
Please observe the following precautions for safe use of the products.
• Never use the product in an environment where combustible or explosivegas is present.
• Please separate from a high-pressure equipment and the power equipment to secure the safety of the operation and
maintenance.
• In the installation, please tighten the screw surely. (Recommended 1.2N
• Please do not insert foreign bodies such as water and the wires from the space of the case.
• Please do not dismantle, repair or modify this product.
• Please process as industrial waste when you abandon this product.
• When you work on wiring and put on and take off cables, CIDRW head, please perform it after switching off this product.
• Provide enough space around this product for ventilation.
• Please avoid installing this product near the machinery (a heater, a transformer, large-capacity resistance) that has high
the calorific value. hen you felt abnormality to this product, and having switched it off.
·m)
Confirm the effects of radio waves on medical devices. The following guideline is from JAISA (Japan
Automatic Identification Systems Association).
This product is a reader-writer that uses radio waves for RFID equipment. The application
and location of this product may affect medical devices. The following precaution must be
observed in the application of the product to minimize the effects on medical devices.
Any person with an implanted medical device must keep the area where the device is
implanted at least 22 cm away from the antenna of a stationary or modular RFID device.
CIDRW System
8
User’s Manual
INTRODUCTION
Precautions for Correct Use
INTRODUCTION
Please observe the following precautions to prevent failure to operate, malfunctions, or undesirable effects on
product performance.
■ About installation Site
Do not install this product in the locations subject to the following conditions.
• Place where direct sunshine strikes.
• Place with corroded gas, dust, metallic powder, and salinity.
• Place with condensation due to rapid temperature fluctuations.
• Place with condensation due to high humidity.
• Place where vibration and impact more than being provided by specification are transmitted directly
to main body.
• Place with spray of water, oil, and chemical medicine.
• The working temperature is within the range stipulated in the specifications.
■ About depositoty Site
• Please follow the save ambient temperature / humidity, and keep this product.
■ About wiring
• Use the power supply voltage specified in this cocument.
• Ensure correct polarity when connecting to the +/- power supply terminals.
• Do not run high-voltage lines and power lines though the same conduit.
• To avoid static-induced failure, wear a wrist band or equivalent means to release a static charge
before touching a terminal or a signal line within a connector.
• When you put on and take off a CIDRW head, please do not add excessive power to a connector.
• Please connect the correct CIDRW head to the amplifier unit.
Precautions in using the product
■ About cleaning
• Use alcohol to clean this product.
• Never use an organic solvent such as thinner, benzene, acetone or kerosene, as it will attack resin
components or case coating.
■ Power and Graound Cables
• Use an appropriate ground. An insufficient ground can affect this product operation or result in damage to this product.
■ About the communication range and time
• Do the communication test with Transponder in the installation environment because the metal,
noise and ambient temperature around CIDRW head damage to the communication range and time.
• Install CIDRW head and ID tag in the appropriate distance because the communication range can
change by the difference of ID tag specifications.
CIDRW System
User’s Manual
9
INTRODUCTION
INTRODUCTION
■ About mounting
• This product communicates with ID Tags using the 134 kHZ frequency band. Some transceivers,
Precautions in using the product
motors, monitoring equipment, and power supplies (power supply ICs) generate electrical waves
(noise) that interfere with communications with ID Tags, If you are using the product in the vicinity of
any of these devices, check the effect on communications in advance.
• In order to minimize the effects of noise, ground nearby metal bodies with a grounding resistance not
exceeding 100 ohms.
• When mounting CIDRW Heads, tighten the screws tightly.(Recommended 0.6N·m)
• When multiple CIDRW Heads are mounted next to each other, communications performance could
be impaired by mutual interference. Read and follow the information in this manual on mutual interference when installing multiple heads.
Refer to page 90.
■ Screw Locking Adhesive
• Screw locking adhesive (screw lock) may cause deterioration and cracking of resin parts; do not use
it for screws in resin parts or anywhere where resin washers are used.
■ Startup Precaution
Never turn OFF the power supply while the CIDRW Controller is starting, including when power is
turned ON, when the mode is changed, or when the CIDRW Controller is being reset. Doing so may
damage the CIDRW Controller.
■ Application Precaution
Never turn OFF the power supply while setting the IP address, subnet mask, or Web password. Doing
so may damage the Amplifier Unit.
10
CIDRW System
User’s Manual
Reading this Manual
INTRODUCTION
INTRODUCTION
Visual Aids
Indicates an explanation of a point that must be observed to ensure that the product is capable of its proper functions and performance. Read this information carefully and follow the cautions. If the product is used incorrectly, data or the equipment itself
could be destroyed.
Indicates summaries of points of particular importance relating to product performance, e.g., points to note during operation and
advice on how to use the product.
Indicates the number of a page where related information can be found.
Indicates information for reference when you encounter a problem.
Indicator Status
Precautions in using the product
The following symbols are used to show the status of the indicators on the CIDRW Controller and Amplifier
Units.
OFF
Flashing
ON
CIDRW System
User’s Manual
11
INTRODUCTION
INTRODUCTION
MEMO
Precautions in using the product
12
CIDRW System
User’s Manual
Table of Contents
INTRODUCTION
Table of Contents
INTRODUCTION
Introduction
Applicable Standards 4
Applicable SEMI Standards 4
Safety Precautions 6
Precautions for Safe Use 7
Precautions for Correct Use 8
Reading this Manual 10
Table of Contents 11
SECTION 1 Product Outline 13
What Is a CIDRW System 14
Features 15
System Configuration 16
Component Names and Functions 17
Flowchart for Getting Started 20
Table of Contents
SECTION 2 Installation and Connections/Wiring 23
Installation 24
Connections and Wiring 27
SECTION 3 Preparing for Communications 31
Setting the Communications Conditions for Amplifier Units 32
Communications Test 33
SECTION 4 Reading from/Writing to ID Tags 35
Command/Response Format 36
SECTION 5 Browser Interface 53
Browser Operation Windows 54
Window Configuration 55
CIDRW System
User’s Manual
13
INTRODUCTION
Table of Contents
INTRODUCTION
SECTION 6 Troubleshooting 69
Table of Contents
SECTION 7 Appendix 77
Troubleshooting 70
Specifications and Dimensions 78
Connection Examples 82
Characteristic Data According to Conditions of Use 83
ID Tag Memory Maps 113
Regular Inspection 114
ASCII Code Table 115
Protective Construction 116
SECTION 8 Revision History 118
14
CIDRW System
User’s Manual
SECTION 1
Product Outline
What Is a CIDRW System 16
Features 17
System Configuration 18
Component Names and Functions 19
Flowchart for Getting Started 22
SECTION 1
Product Outline
CIDRW System
User’s Manual
15
SECTION 1
ID Tag
(holder is separate)
CIDRW Head
Reading and writing
information
• Model information
• Process instruction
information
• Completion
information
• Lot information
• Inspection results
Etc.
Host
Amplifier Unit
Ethernet hub
Recommended: W4S1-05B
(OMRON)
Product Outline
What Is a CIDRW System
SECTION 1
The CIDRW system writes data to, and reads data from, the carrier IDs (ID Tags) mounted on the carriers
(FOUP) in semiconductor manufacturing processes without contacting these ID Tags. CIDRW is the
abbreviation of Carrier ID Reader/Writer and this abbreviation is used throughout this manual.
Reading and writing information such as models, process instructions, lots, and inspection results to and from
What Is a CIDRW System
ID Tags makes it possible to manage work instruction information from a host device.
Example: Management of information in semiconductor and wafer manufacturing processes
16
CIDRW System
User’s Manual
Features
SECTION 1
Product Outline
A V640-series CIDRW Head can be connected to a V640-HAM11-ETN or V640-HAM11-L-ETN Amplifier Unit
to read and write ID Tags manufactured by Texas Instruments (TI). Reading and writing is performed
according to commands from the host device.
■ V640-HAM11-ETN
The V640-HAM11-ETN Amplifier Unit is equipped with Ethernet. The host device is connected through
a LAN cable and controls the Amplifier Units using TCP/IP. The Amplifier Units provide a Web browser
function that allows communications to be set and status to be managed using simple command communications.
■ V640-HAM11-L-ETN
The V640-HAM11-L-ETN Amplifier Unit is equipped with Ethernet and can be connected to a V640HS62 CIDRW Head to perform long-distance communications. The functions of the V640-HAM11-LETN Amplifier Unit are the same as those of the V640-HAM11-ETN Amplifier Unit.
SECTION 1
Features
CIDRW System
User’s Manual
17
SECTION 1
CIDRW Head
V640-HS61
Amplifier Unit
V640-HAM11-ETN
Ethernet hub
Recommended: W4S1-05B(OMRON)
Host device
LAN cable
LAN cable
Host device
CIDRW Head
V640-HS62
Amplifier Unit
V640-HAM11-L-ETN
Ethernet hub
Recommended: W4S1-05B(OMRON)
LAN cable
LAN cable
Product Outline
System Configuration
SECTION 1
System Configuration
V640-HAM11-ETN
V640-HAM11-L-ETN
If the IP address is set on the DIP switch, it will be in the form 192.168.1.@@@. The subnet mask is always 255.255.255.0
The IP address of the Amplifier Unit can be either set on this DIP switch or the desired IP address can be set in ROM. If pins 1 to
5 on the DIP switch are all turned OFF, the IP address that is set in ROM will be used.
18
CIDRW System
User’s Manual
Component Names and Functions
LINK(green)
ACT(yellow)
LINK---lights while linking normally.
ACT---lights when detects a carrier.
V640-HAM11-ETN and V640-HAM11-L-ETN Amplifier Units
SECTION 1
Product Outline
SECTION 1
Component Names and Functions
No. Name Function
1 Dedicated power supply con-
nector
2 Ethernet port Connect to the host device through a LAN cable.
3 RUN indicator (green) Turns ON when the Amplifier Unit is in normal operation.
4 COMM indicator (yellow) Turns ON during communications with the host device or during communications with an
5 NORM indicator (green) Turns ON when the communications finish with no error.
6 ERROR indicator (red) Turns ON when an error occurs during communications with the host device, or during
7 CIDRW Head connection port A CIDRW Head is connected here.
8 Setting DIP switches Set the IP address and enable/disable the Test Mode with this DIP switch.
Connect to the 24 VDC power supply.
ID Tag.
communications with an ID Tag.
The V640-HS61 CIDRW Head is used with the V640-HAM11-ETN. The V640-HS62
CIDRW Head is used with the V640-HAM11-L-ETN.
CIDRW System
User’s Manual
19
SECTION 1
Product Outline
SECTION 1
■ Functions
• NOISE MEASUREMENT
The levels of noise in the vicinity of the CIDRW Head are measured and the noise level is expressed
numerically in the range "00" to "99.
Refer to page 51, page 114.
Component Names and Functions
• Detecting for CIDRW Head status
You can confirm if the CIDRW Head is connected to the Amplifier Unit correctly.
Refer to page 49.
• Test Mode
Test Mode can be used to check communications between the ID Tags and Amplifier Units without
connecting a host device. Communications with ID Tags are automatically performed every second
and the communications results are displayed on the OPERATING indicator.
Refer to page 34.
Refer to V640-HAM11-ETN and V640-HAM11-L-ETN Amplifier Units for information on the OPERATING indicator for communi-
cations results.
Refer to page 19.
Always connect the CIDRW Head before operating the Amplifier Unit in Test Mode. If Test Mode is used without connecting a
CIDRW Head, the ERROR inductor will light and Amplifier Unit operation will stop.
Commands from the host device are not accepted during operation in Test Mode. To end Test Mode, turn OFF the Test Mode pin
on the DIP switch and restart the Amplifier Unit.
• Browser Interface
You can confirm the status of the Amplifier Unit or control the Amplifier Unit by using Browser Interface.
You can...
• confirm the status of the Amplifier Unit
• set the Network Settings and Web Password
• communicate with ID tags
• measure the levels of noise
Refer to page 55.
20
CIDRW System
User’s Manual
V640-HS61 and V640-HS62 CIDRW Heads
V640-HS62
CIDRW HEAD
MADE IN JAPAN
SECTION 1
Product Outline
■ V640-HS61
No. Name Function
1 Antenna Used to communicate with ID Tags.
2 Antenna center This is the center of the communications area.
3 Connector Connect to an Amplifier Unit.
■ V640-HS62
SECTION 1
Component Names and Functions
No. Name Function
1 Antenna Used to communicate with ID Tags.
2 Antenna center This is the center of the communications area.
3 Connector Connect to an Amplifier Unit.
CIDRW System
User’s Manual
21
SECTION 1
Refer to page 26.
Refer to page 29.
Refer to page 34.
Refer to page 35.
Refer to page 36.
Installation
Connection and Wiring
Setting the Communications Conditions for Amplifier Units
Test for Communications with the Host Device
ID Tag <-> CIDRW System Communications Test
Check the Surrounding Environment
Refer to page 27.
Preparation for
Communications
Trial Operation Installation and Connections
Product Outline
Flowchart for Getting Started
SECTION 1
Flowchart for Getting Started
22
CIDRW System
User’s Manual
Refer to page 38.
Refer to page 72. List of Error Messages
Refer to page 72. Amplifier Unit Indicators
Refer to page 73. Operation Check Flowchart
Communications Test with Actual Commands
Troubleshooting
When you Encounter a Problem...
Communications
SECTION 1
Product Outline
SECTION 1
Flowchart for Getting Started
CIDRW System
User’s Manual
23
SECTION 1
Product Outline
MEMO
SECTION 1
Flowchart for Getting Started
24
CIDRW System
User’s Manual
SECTION 2
Installation and Connections/Wiring
Installation 26
Amplifier Unit 26
CIDRW Head 27
Connections and Wiring 29
Amplifier Unit 29
SECTION 2
Installation and Connections/Wiring
CIDRW System
User’s Manual
25
SECTION 2
Mounting dimensions
(Unit: mm)
Installation
SECTION 2
Installation and Connections/Wiring
Installation
Amplifier Unit
Use spring washers and flat washers with the four M4 screws when mounting the Amplifier Unit.
4-M4
Tighten the M4 screws with a torque not exceeding 1.2 N·m.
175±0.5
46±0.5
26
CIDRW System
User’s Manual
SECTION 2
Installation and Connections/Wiring
CIDRW Head
The area for communications with ID Tags varies substantially according to the installation orientations
and the background conditions (metals, noise, etc.). Check the communications area before deciding
the installation position.
For details on actual communications distances, see Characteristic Data depending on Conditions of
Use in Appendix.
Refer to page 85.
■ Positional Relationship between the CIDRW Head and the ID Tag
The communications area differs according to the positional relationship during communications.
SECTION 2
Installation
Mounting
orientation
Coaxial The maximum communications area is
Parallel The maximum communications area is
Vertical When the center point of the antenna on the
Communications area (purely illustrative) Explanation
obtained when the center lines of the CIDRW
Head and the ID Tag coincide.
obtained when the center point of the
antenna on the CIDRW Controller is aligned
with the center line of the ID Tag.
CIDRW Head is aligned with the center line
of the ID Tag, the communications area is
substantially reduced.
■ Data Reading and Writing
The communications distances for reading and writing are not the same; the distance is shorter for
writing. Therefore, when data is to be both read and written, take the distance for writing as the reference distance when installing the CIDRW Head and the ID Tag.
CIDRW System
User’s Manual
27
SECTION 2
Mounting dimensions
(Unit: mm)
Antenna center
21±0.2
20±0.2
9
Antenna center
21±0.2
20±0.2
9
4-M3 OR 3.5 dia.
4-M3 OR 3.5 dia.
Installation and Connections/Wiring
■ Influence of Background Metal on ID Tag
Metals in the vicinity of the communications area will affect the range, making it smaller.
Refer to page 110.
SECTION 2
Installation
■ Influence of Noise
This CIDRW system uses a frequency of 134 kHz for communications with ID Tags. Equipment such
as switching power supplies, inverters, servomotors, or monitors in the surrounding area will adversely
affect communications, restricting the communications area.
The noise levels in the vicinity of the CIDRW Head can be determined with the environmental NOISE MEASUREMENT
command (applies only when SECS is not used) . Refer to page 45.
For details on the relationship between noise and communications distance, see Appendix . Refer to page 114.
■ Mounting
Use spring washers and flat washers with the four M3 screws when mounting a CIDRW Head.
CIDRW System
28
User’s Manual
*The mounting dimensions are same between V640-HS61 and V640-HS62.
Tighten the M3 screws with a torque not exceeding 0.6 N·m.
Loading...