Omron E3Z-H DATASHEET
Photoelectric sensor with anti-tampering in compact plastic housing
E3Z-H
• Compact housing size and high power LED for excellent
performance-size ratio
• IP67 and IP69K for highest water resistance
• Intensive shielding for highest noise immunity (EMC)
• No adjusters to protect against manipulation
• Rugged PBT housing for high mechanical resistance
Ordering Information
Sensor type Sensing
distance
Through-beam 15 m NPN
Retro-reflective with
M.S.R.
Diffuse-reflective
wide-beam
Diffuse-reflective 1 m (adjustable) NPN
*1.
Measured with E39-R1S. The reflector is sold separately.
0.1 to 4 m
0.1 m (adjustable) NPN
*1
Output
configuration
PNP
NPN
PNP
PNP
PNP
Connection method Model
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
For ordering pigtail versions replace '2M' of cable types with:
- M1J: M12 with 30 cm cable
- M3J: M8 4-pin with 30 cm cable
E3Z-T61H 2M
E3Z-T66H
E3Z-T81H 2M
E3Z-T86H
E3Z-R61H 2M
E3Z-R66H
E3Z-R81H 2M
E3Z-R86H
E3Z-D61H 2M
E3Z-D66H
E3Z-D81H 2M
E3Z-D86H
E3Z-D62H 2M
E3Z-D67H
E3Z-D82H 2M
E3Z-D87H
- M5J: M8 3-pin with 30 cm cable
Reflectors (Order seperately)
Name Sensing distance (typical)
Reflectors 3 m [100 mm] 60x40 E39-R1
4 m [100 mm] 60x40 E39-R1S
5 m [100 mm] Ø84 E39-R7
6 m [100 mm] 100x100 E39-R8
4 m [100 mm] 50x50 E39-R42
1.5 m [50 mm] 35x20 E39-R3
Tape Reflector 700 mm [150 mm] 35x10 E39-RS1
1.1 m [150 mm] 35x40 E39-RS2
*1.
Values in parentheses indicate the minimum required distance between the sensor and reflector.
1.4 m [150 mm] 80x70 E39-RS3
*1
Size in mm Model
1E3Z-H
Mounting Brackets
Shape Model Quantity Remarks Shape Model Quantity Remarks
E39-L153 1 Mounting Brackets E39-L150 One set Sensor adjuster
Easy mounting to
aluminum frame/rail of
conveyor or like, easy
adjustment.
E39-L104 1
For left-to-right adjustment
E39-L43 1 Horizontal type
mounting bracket
E39-L142 1 Horizontal type
protective cover bracket
E39-L44 1 Rear mounting bracket
E39-L98 1 Protective cover bracket E39-L144 1 Vertical protective cover
Note: 1 .If a through-beam model is used, order two Mounting Brackets for the emitter and receiver respectively.
2 .For details, refer to the "Mounting bracket list".
E39-L151 One set
E39-L93@ One set Sensor adjuster
Easy mounting to
aluminum frame/rail of
conveyor or like, easy
adjustment.
For vertical angle
adjustment
bracket
Sensor I/O Connectors
Size Cable type Shape Cable length Model
M8 Standard cable 2 m 4-wire type XS3F-M421-402-A
M12 (for -M1J) 2 m 4-wire type XS2F-D421-D80-A
Straight
L-shaped
Straight
L-shaped
5 m XS3F-M421-405-A
2 m XS3F-M422-402-A
5 m XS3F-M422-405-A
5 m XS2F-D421-G80-A
2 m XS2F-D422-D80-A
5 m XS2F-D422-G80-A
2 Standard Photoelectric Sensors
Rating/performance
Item Through-beam Retro-reflective with
M.S.R.
NPN output E3Z-T61H/T66H E3Z-R61H/R66H E3Z-D61H/D66H E3Z-D62H/D67H
PNP output E3Z-T81H/T86H E3Z-R81H/R86H E3Z-D81H/D86H E3Z-D82H/D87H
Sensing distance 15 m 4 m (100 mm)*1 *
(When using the
E39-R1S)
Standard sensing object Opaque: 12-mm dia.
min.
Differential distance --- 20% max. of sensing distance
Directional angle Both emitter and
receiver: 3° to 15°
Light source (wave length) Infrared LED (860 nm) Red LED (680 nm) Infrared LED (860 nm)
Power supply voltage 12 to 24 VDC ±10%, ripple (p-p) : 10% max.
Current consumption emitter: 15 mA
receiver: 20 mA
Control output Load power supply voltage 26.4 VDC max., load current 100 mA max. (residual voltage 2 V max.) Open
collector output type (depends on the NPN/PNP output format), Light-ON/Dark-ON selectable by wiring
Protective circuits Protection from load
short-circuit and reversed power supply
connection
Response time Operation or reset: 1 ms max.
Sensitivity adjustment no adjustment Single-turn adjustment
Ambient illuminance Incandescent lamp: 3,000 lux max. Sunlight 10,000 lux max.
Ambient temperature Operating: -25°C to 55°C, Storage: -40°C to 70°C (with no icing or condensation)
Ambient humidity Operating: 35% to 85% RH, Storage: 35% to 95% RH (with no icing or condensation)
Insulation resistance 20 MΩ min. at 500 VDC
Dielectric strength 1,000 VAC at 50/60 Hz for 1 minute
Vibration resistance 10 to 55 Hz, 1.5-mm or 300m/s2 double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67, IP69k after DIN 40050 part 9
Connection method Pre-wired (standard length: 2 m/500 mm)/M8 connector
Indicator lamp Operation indicator (orange), stability indicator (green) [Note that the emitter has the power indicator
(orange) only]
Weight
(Packed
state)
Material Case PBT (polybutylene terephthalate)
Accessories Instruction manual (The Reflector or Mounting Bracket is not provided with any of the above models.)
*1.
Pre-wired
models (with
2-m cable)
Connector type 30 g Approx. 20 g
Lens Methacylate resin
Values in parentheses indicate the minimum required distance between the sensor and reflector.
Approx. 120 g 65 g
Opaque: 75-mm dia.
min.
2° to 10° ---
30 mA max.
Reverse polarity protection, output short-circuit protection, mutual interference
prevention, output reverse protection
Diffuse-reflective
wide-beam standard-beam
100 mm
(White paper
100 x 100 mm)
---
1 m
(White paper
300 x 300 mm)
3E3Z-H
Loading...