OKI ML 420, ML 421, ML 491, ML 620, ML 690 User Manual

...

OkiLAN 6130 Network Card Installation . . . . . . . . . . . . . . 3

Installation de la carte réseau OkiLAN 6130

Instalación de la Tarjeta de Red OkiLAN 6130

Instalação da placa de rede OkiLAN 6130

........... 9

. . . . . . . . . . . . . 21

. . . . . . . . . 15

OkiLAN 6130 Network Card Installation

The OkiLAN 6130 Print Server enables Ethernet network users to connect to a network-conﬁgured printer. It supports 10/100-megabit networks, TCP/IP Direct Printing and Server-Based Printing.

Note: Before using the parallel port, you must remove the OkiLAN 6130 from the printer —see

Note: The OkiLan 6130 can only be used be used without a parallel cable being

your on-line OkiLAN User’s Guide for instructions on how to do this.

connected.

Installing the OkiLAN 6130 Network Card

1. Turn off printer power.

2. Unplug the power cord.

3. Detach the interface cable from the rear of the printer.

4. Pry off the breakaway panel next to the interface connector with a screwdriver

Breakaway panel

Note: Your printer may look like

either example below.

5. Insert the OkiLAN 6130 by sliding it along the rails in the recess of the printer, until it is plugged into the socket in the rear of the recess.

6. Attach the 10/100Base-T UTP cable to the receptacle on the back of the OkiLAN 6130. Attach the other end of the cable to the Network.

7. Plug the power cord into the power outlet (if provided).

Powering On the OkiLAN 6130

Turn printer power on. The red and green indicators on the OkiLAN 6130 blink during self-test. When self-test completes successfully, the red indicator goes off and the green indicator stays on.

Green Indicator

Red Indicator

Printing a Conﬁguration Sheet

To print conﬁguration information, press and hold the Test button on the front of the OkiLAN 6130 for ﬁve seconds.

Note: By default, the conﬁguration sheet prints in ASCII text.

The content of the conﬁguration sheet depends on your printer and system setup.

Conﬁguring Your Print Server

Using OKI’s ExtendView Utility to Conﬁgure Your IP Address

First, download the ExtendView utility from OKI Data’s website at http://www.okidata.com – navigate to the page for your speciﬁc product, then click on Drivers, then Utilities,to locate the software.

Next, install the ExtendView utility and launch the application.

1. In the ExtendView utility, highlight the device you are going to conﬁgure.

2. Choose the conﬁguration option from the dropdown menu.

3. From the Server Conﬁguration box, click Set Permanent. Then, if you wish to change the IP address, Subnet Mask and Default Gateway, you may do so.

When the desired options have been set, click OK. The Print Server

will automatically be reset at this point, and your options will have been saved.

(If you have network conﬁguration questions, please contact your

network administrator.)

Proceed to the instructions for Installing Your Driver.

Using Your Print Server’s Built-In Web Page to Conﬁgure Your IP Address (Alternate Method)

First, open your browser. Then, type the IP address of your Print Server into the browser’s address bar. (If the IP address is unknown, you can obtain it by pressing and holding the Test Button on the front of the OkiLAN 6130 for ﬁve seconds)

1. Log into the Print Server as Admin. (Username: admin Password: OkiLAN)

2. Select the TCP/IP option from the Network Connection menu to launch the TCP/IP Conﬁguration menu.

3. From the TCP/IP Conﬁguration Menu, click Set Permanent under the IP Address Resolution option. Then, if you wish to change the IP address, Subnet Mask and Default Gateway, you may do so.

When the desired options have been set,

click Submit Changes. The Print Server will automatically be reset at this point, and your options will have been saved.

(If you have network conﬁguration questions,

please contact your network administrator.)

Proceed to the instructions for Installing Your

Driver.

Installing Your Driver

From the CD or OKI Data website - follow the installation instructions.

Entering the Printer IP Address

While installing the printer driver for TCP/IP using the CD supplied with your printer. When you come to the screen requesting the IP Address for the printer, you must select “IP Address”

(instead of the default “Search address”) and type in the printer’s IP Address before clicking Next. If you need help, please contact your Network Administrator for the IP Address to use.

LPR

Make sure there are no error conditions in the printer (e.g., paper jam) before you use LPR to discover the printer. The product driver utility is available from OKI Data’s website at http://www.okidata.com

Resetting to Factory Defaults

1. Turn off the printer.

2. Turn on the printer and wait for the print server to boot up (about 30 seconds).

3. Press and hold the Test button on the front of the OkiLAN 6130 for 20 seconds. The lights will ﬂash brieﬂy after releasing the button, then the card will reset.

Note: Your printer may look like either example below.

4. Release the TEST button.

The print server resets to the factory default settings and reboots.

Installation de la carte réseau OkiLAN 6130

Le serveur d’impression OkiLAN 6130 permet aux utilisateurs de réseau Ethernet de se brancher à une imprimante conﬁgurée réseau. Il prend en charge les réseaux 10/100 mégabit, l’impression directe TCP/ IP et l’impression basée serveur.

Remarque : On ne peut utiliser l’OkiLAN 6130 que s’il n’y a pas de câble parallèle de connecté.

Installation de la carte réseau OkiLAN 6130

1. Éteignez l’imprimante.

2. Débranchez le cordon d’alimentation.

3. Détachez le câble d’interface de l’arrière de l’imprimante.

Remarque : Votre imprimante peut

ressembler à l’une ou l’autre des illustrations ci-dessous.

4.À l’aide d’un tournevis, dégagez par effet de levier le panneau défonçable près du connecteur d’interface.

le panneau défonçable

+ 19 hidden pages