OKI C831 User Manual

C831

Safety, Warranty and Regulatory Information . . . . . . . . . . . . . . . .2

Informations de sécurité, de garantie, et de réglementation . . . .15

Información sobre seguridad, garantía, y regulaciones . . . . . . . .23

Informações sobre segurança, garantia e normativas . . . . . . . . .35

Country/Region • Pays/Région • País/región • País/região

United States and Canada, Etats-Unis et

Canada, Estados Unidos y Canadá

English

Safety Information . . . . . . . . . . . . . . . . . . . . . 2-3

Warranty Information . . . . . . . . . . . . . . . . . . . . 4

Service and Support . . . . . . . . . . . . . . . . . . . . . 5

Regulatory Information . . . . . . . . . . . . . . . . . . . 6

Material Safety Data Sheet (MSDS) . . . . . . . . 7, ff.

Français

Informations sur la sécurité . . . . . . . . . . . . . 15-16

Information sur la garantie . . . . . . . . . . . . . . . .17

Service et soutien. . . . . . . . . . . . . . . . . . . . . . .18

Informations réglementaires . . . . . . . . . . . . . . .20

Fiche technique santé-sécurité (MSDS) . . . . . 21, ff.

Español

Información de Seguridad . . . . . . . . . . . . . . 23-24

Información sobre la garantía . . . . . . . . . . . . . .25

Servicio y Apoyo. . . . . . . . . . . . . . . . . . . . . . . .27

Información reglamentaria . . . . . . . . . . . . . . . .30

Hojas de Información sobre Seguridad de los

Materiales (MSDS) . . . . . . . . . . . . . . . . . . 31, ff.

Mexico, México

Español

Información de Seguridad . . . . . . . . . . . . . . 23-24

Información sobre la garantía . . . . . . . . . . . . . .28

Servicio y Apoyo. . . . . . . . . . . . . . . . . . . . . . . .28

Información reglamentaria . . . . . . . . . . . . . . . .30

Hojas de Información sobre Seguridad

de los Materiales (MSDS). . . . . . . . . . . . . . 31, ff.

America Latina (otro),

Latin America (other)

Español

Información de Seguridad . . . . . . . . . . . . . .23-24

Información sobre la garantía . . . . . . . . . . . . . . 29

Servicio y Apoyo . . . . . . . . . . . . . . . . . . . . . . . 29

Información reglamentaria . . . . . . . . . . . . . . . . 30

Hojas de Información sobre Seguridad

de los Materiales (MSDS) . . . . . . . . . . . . . 31, ff.

English

Safety Information . . . . . . . . . . . . . . . . . . . . 2-3

Regulatory Information . . . . . . . . . . . . . . . . . . . 6

Material Safety Data Sheet (MSDS) . . . . . . . . .7, ff.

Brasil, Brazil

Português

Informações de segurança . . . . . . . . . . . . . .35-36

Informações sobre a garantia . . . . . . . . . . . . . . 37

Informações normativas. . . . . . . . . . . . . . . . . . 38

Ficha de Informação de Segurança

do Produto . . . . . . . . . . . . . . . . . . . . . . . 39, ff.

English

Safety Information . . . . . . . . . . . . . . . . . . . . 2-3

Regulatory Information . . . . . . . . . . . . . . . . . . . 6

Material Safety Data Sheet (MSDS) . . . . . . . . .7, ff.

English

Safety Information . . . . . . . . . . . . . . . . . . . . . 2-3

Regulatory Information . . . . . . . . . . . . . . . . . . . 6

Material Safety Data Sheet (MSDS) . . . . . . . . 7, ff.

Safety, Warranty and Regulatory Information

• Do not poke anything into the ventilation slots of the

Safety Information,

120-Volt Models

Your OKI product has been carefully designed to give y o u years of safe, reliable performance. As with all electrical equipment, there are a few basic precautions you should take to avoid hurting yourself or damaging the product.

• Carefully read the provided setup and operating instructions.

• Save all provided documentation for future reference.

• Read and follow all warning and instruction labels on the product itself.

• Unplug the product before you clean it. Use only a damp cloth; do not use liquid or aerosol cleaners.

• Place your product on a firm, solid surface. If you put it on something unsteady, it may fall and be damaged. If you place it on a soft surface, such as a rug, sofa, or cushion, the vents may be blocked, causing the product to overheat.

• Protect your product from overheating. Make sure no obstructions block the openings of the product. Do not put the product on or near a heat source (such as a radiator or heat register). Keep the product out of direct sunlight.

• Always use this product in a well ventilated area. Allow enough room around the product for adequate ventilation and easy access to the paper trays. If you put the product in any kind of enclosure, make sure the enclosure is well ventilated.

• Do not use your product near water. Do not spill liquid of any kind into it.

• Be certain that your power source matches the rating listed on the back of the product. If you are not sure, check with your dealer or with your local power company.

• Do not connect this product to an uninterruptible power supply (UPS). For further information please contact Oki Data at 1-800-OKI-DATA.

• Your product has a grounded, three-prong plug as a safety feature. This plug only fits into a grounded outlet. If the plug does not fit, the outlet may be an older, non-grounded type. Contact an electrician to have the outlet replaced. Do not use an adapter to defeat the grounding.

• Install the product near an easily accessed power outlet.

• Avoid damaging the power cord. Do not put anything on it or place it where it will be walked on. If the cord becomes damaged or frayed, replace it immediately.

• If you are using an extension cord or power strip with the product, make sure that the total of the amperes required by all the equipment on the extension is less than the extension’s rating. The total ratings of all equipment plugged into the outlet should not exceed 15 amperes.

product. You could get an electrical shock or cause hazardous electrical arcing, which could cause a fire.

• Aside from the routine maintenance described in the documentation, do not try to service the product yourself. Removing the cover may expose you to shocks or other hazards.

• Do not make any adjustments other than those outlined in the documentation. You ma y cause damage that will require extensive repair work. The provide d documentation explains how to get your product serviced by qualified Oki Data technicians.

If anything happens that indicates that your product is not working properly or has been damaged, unplug it immediately and follow the procedures in the provided documentation for having your product serviced.

Here are some of the things to look for.

• The power cord or plug is frayed or damaged.

• Liquid has been spilled into the product, or the product has been exposed to water.

• The product has been dropped, or the cabinet is damaged.

• The product does not function normally when you are following the operating instructions.

2 - English

Safety Information,

220/240-Volt Models

This product has been carefully designed to give years of safe, reliable performance. As with all electrical equipment, however, there are a few basic precautions that should be taken to avoid injury or damage:

Ensure this and all other documentation is both read carefully and retained for future reference.

Ensure all warning and instruction labels on the product are read, understood and followed in order to prevent any risk of injury.

This product may be heavy. Please check the weight of the product and take all necessary precautions to prevent the risk of personal injury.

The product must be placed on a flat solid surface strong enough to support its weight to prevent any risk of injury.

Ensure that there is adequate ventilation all around the product to prevent overheating and any risk of fire.

Keep the product away from direct heat sources such as radiators and out of direct sunlight to prevent any risk of overheating.

The power supply required for this product is 220-240 VAC, 50/60 Hz. (For any DC powered product, the figures are 9.6-

31.2VDC, 4-1.8A.) Refer to your prod uct's rating label on the machine for full power ra ti ng de tails. Ensure that you have a suitable power supply before connecting the product. If in doubt contact your dealer or check with your local power provider.

Ensure both the product and mains power switches are in the OFF position before connecting the AC power cable.

Do not connect or disconnect the power plug with a wet hand as this may cause electric shock.

Always hold the power plug to connect/disconnect the power cable to/from the mains socket. Unplugging by pulling on the cable can cause fraying and may lead to fire or electric shock.

This product has an earthed plug as a safety feature and will only connect to an earthed socket. Do not attempt to defeat the earthing or there is a risk of fire or shock.

If using an extension cable or power strip ensure that the total current rating (amperes) of all connected equipment is less than the maximum rating of the extension cable, power strip or wall outlet. If the product is already supplied with a fitted power strip then no additional power strip or extension cable should be used to connect to the mains wall outlet. Otherwise, fire or shock may occur.

Ensure the power cable is routed so as not to be damaged or cause a trip hazard. If the cable becomes frayed or damaged replace it immediately to prevent any risk of shock.

Do not twist, constrict or knot the power cable as this can cause overheating which may lead to fire or electric shock.

Ensure the power socket to which the product is connected is easily accessible at all times and not obstructed.

Use only the power cable supplied. Using a power cable not intended for this product may lead to fire or electric shock.

To avoid risk of fire and electric shock, do not use the power cable supplied with this product for any other electrical equipment.

If you do not connect the power cord or any other cables only as directed in the User's Guide, this may result in a fire.

It is recommended that the machine is switched off prior to opening covers; otherwise there is a risk of electric shock.

When the product cover is open, do not touch the fuser unit or print head as you may receive burns. Allow it to cool before touching.

If the product casing gets extremely hot or smoke, unusual smells or abnormal noises are emitted from the product, there is a risk of fire. Unplug the mains connector and contact your dealer.

If the product has been knocked over or damaged, there is a risk of electric shock, fire and/or injury. Unplug the mains connector and contact your dealer.

If any liquid (for example water) is allowed to enter the product, there is a risk of fire. Unplug the mains connector and contact your dealer.

Do not place containers containing liquid on the product as electric shock, fire and/or injuries may occur.

If any foreign objects (for example clips) are allowed to enter the product, there is a risk of electric shock, fire and/or injury . Unplug the mains connector before removing the object.

Do not introduce foreign objects into the ventila tion ho les or operate this product with any covers open or doors re moved as electric shock, fire and/or injuries may occur.

Do not use an extremely flammable spray near the product as the product contains high temperature parts that may cause a fire.

Switch the product off before cleaning to prevent any risk of injury . Clean using a damp cloth. Do not use liquid or aerosol cleaners.

Ensure loose clothing and hair is kept clear of moving parts when the product is in operation to prevent possible risk of injury.

Do not carry out any operations on the product that are not specified in the User's Guide . This may res ult in electric sh ock, fire and/or injury.

Do not touch the battery if one is fitted to the product. There is a risk of explosion if the battery is replaced by an incorrect type. The product battery should not require replacement during the life of the product.

Do not throw toner cartridges or image drum cartridges into a fire as you may receive burns from a dust explosion.

After installing additional memory, hard disk drive, or any other internally fitted option, any covers removed or doors opened must be closed or replaced and secured to prevent risk of fire.

The acoustic noise of this product is less than 70 dB (A) as measured in accordance with EN ISO 7779.

The operating condition range for your product is: 10 to 32°C and 20 to 80% RH. Operation of the product outside this range could result in damage to the product.

If a scanner, finisher etc. is fitted, exercise care when moving these items so as to avoid risk of entrapment or personal injury.

If the product is installed on a cabinet or high capacity feeder, ensure wheel locks are applied once placed in final position for use, to prevent risk of movement or injury.

3 - English

Limited Warranty, US and Canada

U.S. and Canada only

Oki Data Americas, Inc. (Oki Data) warrants this C831 printer (hereinafter "the Product") to be free from defects in material and workmanship and will remedy any such defect according to, the terms of this

Oki Data will repair or at its option, replace, with the same or its functional equivalent, at no charge, any defective component(s) of the Product for one (1) year from the date of purchase except for the printhead (LED imaging arr ay), which is warranted for a period of five (5) years from the date of purchase.

Limited Warranty

This purchaser of the warranted item. This not transferable. This consumable items or supplies, such as toner cartridges, image drums, ribbon cartridges, fuses, etc.

On-Site Repair Note:

On-Site Repair is available in the United States and Canada only. On-Site Repair does not include the replacement or repair of Product consumables or supplies.

Oki Data will, for a period of one (1) year from the date of original purchase, repair or replace (at Oki Data 's op tion) on-site at the original purchaser's facility and without charge, any defective component(s) of the Product provided that the warranty service is performed by an Oki Data authorized service provider. The printheads (LED imaging arrays) have a 5-year parts only warranty from date of original purchase. Following the first y ear of warranty cover age, the printheads will be replaced by an authorized Oki Data service provider at Oki Data 's then current labor rates.

To make request or claim for service under the one (1) year parts and labor coverage of this contact your Oki Data Authorized Dealer, authorized thirdparty service provider, or Oki Data. Oki Data reserves the right to use new and/or refurbished parts for the warr anty repair.

As a condition of this On-Site Repair must include the name and phone number of a fully competent and responsible adult with the authority to consent to the entry of the servicing technician to the premises where the Product is located, and who will remain with the servicing technician while the service work is performed. Any and all dangerous conditions must be removed from the site prior to and throughout the time a service technician is present. The service technician may refrain from entering the premise s or continuing to provide services at any site, if in the servicing technician's reasonable judgement the site poses a risk of physical harm or danger. If warranty services cannot be performed or completed due to any of the foregoing reasons the On-Site service option is null and void and the Product must be returned to an authorized Oki Data service location for warranty repair service.

only extends to the original

Limited Warranty

does not extend to

Limited Warranty,

Limited Warranty

, requests for

To make a request or claim for service under this

Warranty

center, Oki Data at 1-800-654-3282 (1-800-OKI-DATA), or www.okiprintingsolutions. com.

Once the one (1) year on-site period is over, the original purchaser must return the Product, shipping prepaid, in the original shipping container or equivalent to Oki Data or an authorized Oki Data service center and assume the risk of loss or damage in transit.

A written receipt for the Product, showing the date of purchase, dealer's name, and both the model and serial numbers of this Product must accompany any request or claim for work to be performed under this

This tear and shall not apply if the Product has been damaged due to abuse, misuse, misapplication, accident, improper storage, or installation, an unsuitable physical operating environment, or as a result of service or modification by any other than an authorized Oki Data service center.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIODS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, so the abov e limitation ma y not apply to y ou.

IN NO EVENT SHALL OKI DATA OR ITS AFFILIATES BE LIABLE TO A PURCHASER OR ANY OTHER PERSON FOR SPECIAL, COLLATERAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOST PROFITS, BUSINESS REVENUE, GOODWILL OR ANTICIPATED SAVINGS IN CONNECTION WITH OR ARISING OUT OF THE PURCHASE OR USE OF THE OKI DATA PRODUCT, WHETHER ARISING IN CONTRACT OR IN TORT, WHETHER OR NOT CUSTOMER SHALL HAVE INFORMED OKI DATA OF THE POSSIBILITY OR LIKELIHOOD OF ANY SUCH DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you.

ADDITIONAL WARRANTY DISCLAIMERS FOR ALL PURCHASERS EXCEPT CONSUMERS:

Additional information on obtaining service under this

Limited Warranty

contacting the Oki Data dealer from whom the Product was purchased, by contacting Oki Data directly at

, contact your local Oki Data authorized service

Limited Warranty

WHEN ANY OKI DATA PRODUCT SHALL BE PURCHASED BY ANY PERSON SUCH THAT THE OKI DATA PRODUCT IS NOT A "CONSUMER GOOD" (AS DEFINED IN THE UNIFORM COMMERCIAL CODE ADOPTED IN THE STATE OF PURCHASE OR IN OTHER APPLICABLE LAW), OKI DATA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

shall not apply to normal wear and

in the U.S. and Canada is available by

Limited

4 - English

1-800-654-3282 (1-800-OKI-DATA), or by contacting one of the service locations listed below. Spanish Only: call 1-856-222-5276. Canada Only: call 1-905-238-4275.

United States

Oki Data Americas, Inc.

2000 Bishops Gate Blvd.

Mt. Laurel, NJ 08054 Phone: 1-800-654-3282 Fax: 1-856-222-5247

This

Limited Warranty

Canada

Oki Data Americas, Inc.

4140B Sladeview Crescent Units

7 & 8 Mississauga, ON Canada L5L 6A1 Phone: 1-905-508-5000 Fax: 1-905-508-5040

applies to this Product. However, the procedure for obtaining service may vary outside the continental United States. Contact your Oki Data dealer for such warranty service information.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Service and Support,

US and Canada

U.S. and Canada only

Oki Data is firmly committed to the satisfaction of our customers. If you have a problem that your customer documentation cannot solve, contact the listed sources for service or support.

Oki Data Authorized Service Providers

For the most comprehensive, up-to-date listing of Oki Data authorized Service Centers in the United States and Canada :

• In the U.S. go to www.okiprintingsolutions.com.

• In Canada and the U.S., call 1-800-654-3282

(1-800-OKI-DAT A).

Oki Data Contact Locations

United States

Oki Data Americas, Inc.

2000 Bishops Gate Blvd.

Mt. Laurel, NJ 08054 Phone: 1-800-654-3282 Fax: 1-856-222-5247

Sales and Service Dealers

Consult the store location where you purchased your machine, or contact Oki Data for the location of the nearest Authorized Oki Data Service Dealer.

• Prices and minimum charges may vary.

• Proof of purchase is required for warranty work. Be sure to retain your purchase documents.

Canada

Oki Data Americas, Inc.

4140B Sladeview Crescent Units

7 & 8 Mississauga, ON Canada L5L 6A1 Phone: 1-905-508-5000 Fax: 1-905-508-5040

Automated Services for Your Convenience Quick Referrals

To get quick referrals for a local Sales and Service Authorized Reseller, including products, parts and consumable supplies, contact us at any time:

• 1-800-654-3282 (1-800-OKI-DATA)

• www.okiprintingsolutions.com

Your Own Personal Solutions Center

You can easily create your own Personal Solutions Center providing up-to-the-minute Oki information specifically for your product, including:

•Product news

• Manuals

• Drivers and utilities

• Material Safety Data Sheets

• Searchable knowledge base

•and much more!

Just take a few minutes setting it up once, then you can check your Personal Solutions Center for the latest information at any time.

Get started today by visiting http://MY.OKIDATA.com.

Customer Support Representatives 1-800-654-3282 (1-800-OKI-DATA)

Customer Support Representatives are available 24 hours a day, 7 days a week. Please have the model number and serial number for your machine handy. Be sure that you are calling from a telephone close to your machine so you can describe your problem accurately and follow up on the suggestions of the Customer Support Representative right while you are on the phone. Our Customer Support Representatives are trained on all current OK I products. They can answer your qu estions regarding:

• Locations of sales and service dealers

• Installation of your machine

• Usage/normal maintenance of your machine

• Error message interpretation/solutions

• Parts and supplies identification

• Consumer relations Note: Customer Support Representatives are not trained

to provide assistance with the use of commercial software packages. Please consult your software user’s manual for times and availability of their support.

5 - English

Regulatory Information

ENERGY STAR®

As an ENERGY STAR Partner, Oki Data has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Year 2000 Compliance

This product is Ye ar 2000 Com pliant. It contains information technology that accurately processes date and time data between the years 1999 and 2000, and carries no issue for the September 9, 1999 (9999) programming concern. This product, when used in combination with products purchased from other manufacturers, whose products properly exchange data and time information, will accur ately process the date and time.

Federal Communications Commission (FCC)

Declaration of Conformity

1.Product Identification

Product Name Model Name

C831 (120 V) N35100A Second Paper Tray N35110A Duplexer N35120A

2.Statement This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

3.Responsible Party Oki Data Americas, Inc.

2000 Bishops Gate Boulevard Mt. Laurel, NJ 08054-4620

1-800-654-3282 (1-800-OKI-DATA)

FCC Radio Frequency Interference Statement

WARNING: This equipment has been tested a nd found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installe d and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Plug the unit into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Note:

Changes or modifications not expressly approved by Oki Data may void your authority to operate this device.

It is the responsibility of the user to obtain the required shielded cable in order to ensure compliance of this equipment with FCC regulations.

Industry Canada (IC) Radio Interference Statements

This Oki Data apparatus complies with the Class B limits for radio interference as specified in the IC Radio Interference Regulations.

European Union Council of the European Communities Statements of Conformance for 220/240-Volt Models

Electromagnetic Conformance

This product complies with the requirements of the Council Directive 89/336/EEC on the approximation of the laws of the member states relating to electromagnetic compatibility.

Safety Conformance

This product is in conformity with Directive 73/23/EEC on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits.

6 - English

Material Safety Data Sheet

#58387801

Yellow Toner: P/N 44844509

For more information, contact Oki Data at: 2000 Bishops Gate Boulevard, Mount Laurel, NJ 08054-4620.

Emergency Information

Canada only.

Emergency First Aid Procedures

Toner swallowed (ingested)

Immediately seek medical attention. Never give anything by mouth to an unconscious person. If possible, rinse out mouth and give one or two glasses of water or milk to drink.

Toner inhaled.

Remove person to fresh air. Seek medical attention.

Toner gets in the eyes.

Flush eyes with large quantities of cool water for 15 minutes, keeping the eyelids open with fingers. If necessary, seek medical attention.

Toner gets on the skin.

Wash toner off the skin with plenty of cool water and soap. If necessary, seek medical attention.

Note:

Small amounts of toner on skin or clothing can easily be removed with soap and makes toner harder to remove.

Hazardous Ingredients

Silica dioxide (about 2% by weight)

CAS#: Trade Secret. OSHA PEL: Not established. ACGIH TLV: Not established. LD50: Not Available. LC50: Not Available.

Physical Data

Physical State: Melting/Freezing Point: Boiling Point: PH:

Not available.

Vapor Pressure: Vapor Density (Air=1): Evaporation Rate (Butyl Acetate=1): Specific Gravity (H2O=1): Solubility in Water: Solubility in Solvents:

toluene, chloroform and tetrahydrofuran.

Coefficient of water/oil Distribution: Appearance and Odor: Odor Threshold:

Solid.

Not available.

: call 1-800-654-3282; US and

cold

water. Hot water

Not available.

1.1 to 1.2 at 20°C (68°F).

Not available.

Some components are soluble in

Not available.

Yellow powder, no odor.

Not available.

Fire and Explosion Hazard Data ____

Minimal fire hazard. Large quantities may cause

risk of dust explosion. Flash Point (Method Used): Flammable Limits

Lower Explosive Limit:

Upper Explosive Limit: Auto-Ignition Temperature Explosion Data

Sensitivity to Mechanical Impact:

Sensitivity to Static Discharge: Extinguishing Media:

case of large fire, shut off air by spraying with water or foam.

Special Fire Fighting Procedures:

upwind position. Avoid inhalation of smoke or gases. Wear self-contained breathing apparatus.

Hazardous Combustion Products:

oxides of nitrogen.

In case of small fire, use CO2. In

Not applicable.

Not available.

: Not available.

Not available.

Fight fire from

Carbon monoxide,

Toxicological Properties

Routes of Entry: Effects of Acute Exposure: Effects of Chronic Exposure: Exposure Limits: Irritancy: Sensitivity: Carcinogenicity

IARC:

NTP:

OSHA:

Reproductive Toxicity: Teratogenicity: Mutagenicity: Name of Toxicoligically Synergistic Products:

available.

Not available.

Silica Dioxide—Group 3. Not classifiable.

No components are listed.

Inhalation, Ingestion, Eyes, Skin.

Not available.

Not

Reactivity Data

Stability: Conditions to Avoid:

ignition.

Polymerization: Hazardous Decomposition or Byproducts:

Combustion products include harmful gases such as carbon monoxide and nitrogen oxides.

Incompatibility:

Stable in general.

Avoid excess heat and all sources of

Will not occur.

Not available.

7 - English

Preventive Measures ___________

Personal Protective Equipment Respiratory Protection:

spills, use dust respirator during cleanup.

Protective Gloves and/or Eye Protection:

normally required. For larg e spills, use rubber gloves and safety goggles during cleanup.

Engineering Controls Ventilation:

required.

Other Protective Equipment and/or Hygienic

Practices:

Spill Cleanup

Small Spills

1. Remove sources of ignition.

2. Carefully clean up the spill with a wet cloth, avoiding inhalation of fine dust.

Large Spills

1. Remove sources of ignition and keep unnecessary and unprotected personnel away from area.

2. Wear protective gear: respirator, rubber gloves, safety goggles.

3. Vacuum the spill, then wipe up re mainder with a wet cloth.

Waste Disposal

• Prevent release of material into natural waters and sewers.

• Follow appropriate federal, state and local regulations.

• Small amounts can be incinerated.

Careful! carbon monoxide and nitrogen oxides.

• Large amounts must be passed to a licensed waste contractor.

Outside of normal ventilation, not normally

None.

Combustion can create harmful gases such as

Not normally required. F or large

Not

Precautions Precautions for Handling or Storage:

sun. Store in a cool room, under 104°F (40°C). Keep out of reach of children.

Other Precautions: Shipping Information

Special Shipping Information:

container carefully to avoid shock. Do not drop. Keep dry.

None.

Non hazardous. Handle

Protect from the

User’s Responsibility

This bulletin cannot cover all possible situations which the user may experience when using this product. Each aspect of your operation must be exam ined in regard to if , or where, additional precautions may be necessary. All health and safety information contained in this bulletin must be provided to your employees or customers. It is yo ur responsibility to use this information to develop appropriate work practice guidelines and employee instructional programs for your operation.

Preparation Date of MSDS

Date:

November 20, 2012.

Prepared by:

Oki Data Americas, Inc. Engineering Services Department. 2000 Bishops Gate Blvd. Mt. Laurel, NJ 08054-4620

Tel: (856) 235-2600 Fax: (856) 222-5320 http://

WWW.OKIPRINTINGSOLUTIONS.COM

my.okidata.com

8 - English

Material Safety Data Sheet

#58387901

Magenta Toner: P/N 44844510

For more information, contact Oki Data at: 2000 Bishops Gate Boulevard, Mount Laurel, NJ 08054-4620.

Emergency Information

Canada only.

Emergency First Aid Procedures

Toner swallowed (ingested)

Immediately seek medical attention. Never give anything by mouth to an unconscious person. If possible, rinse out mouth and give one or two glasses of water or milk to drink.

Toner inhaled.

Remove person to fresh air. Seek medical attention.

Toner gets in the eyes.

Flush eyes with large quantities of cool water for 15 minutes, keeping the eyelids open with fingers. If necessary, seek medical attention.

Toner gets on the skin.

Wash toner off the skin with plenty of cool water and soap. If necessary, seek medical attention.

Note:

Small amounts of toner on skin or clothing can easily be removed with soap and makes toner harder to remove.

Hazardous Ingredients

Silica dioxide (about 2% by weight)

CAS#: Trade Secret. OSHA PEL: Not established. ACGIH TLV: Not established. LD50: Not Available. LC50: Not Available.

Physical Data

Physical State: Melting/Freezing Point: Boiling Point: PH:

Not available.

Vapor Pressure: Vapor Density (Air=1): Evaporation Rate (Butyl Acetate=1): Specific Gravity (H2O=1): Solubility in Water: Solubility in Solvents:

toluene, chloroform and tetrahydrofuran.

Coefficient of water/oil Distribution: Appearance and Odor: Odor Threshold:

Solid.

Not available.

: call 1-800-654-3282; US and

cold

water. Hot water

Not available.

1.1 to 1.2 at 20°C (68°F).

Not available.

Some components are soluble in

Not available.

Magenta powder, no odor.

Not available.

Fire and Explosion Hazard Data ____

Minimal fire hazard. Large quantities may cause

risk of dust explosion. Flash Point (Method Used): Flammable Limits

Lower Explosive Limit:

Upper Explosive Limit: Auto-Ignition Temperature Explosion Data

Sensitivity to Mechanical Impact:

Sensitivity to Static Discharge: Extinguishing Media:

case of large fire, shut off air by spraying with water or foam.

Special Fire Fighting Procedures:

upwind position. Avoid inhalation of smoke or gases. Wear self-contained breathing apparatus.

Hazardous Combustion Products:

oxides of nitrogen.

In case of small fire, use CO2. In

Not applicable.

Not available.

: Not available.

Not available.

Fight fire from

Carbon monoxide,

Toxicological Properties

Routes of Entry: Effects of Acute Exposure: Effects of Chronic Exposure: Exposure Limits: Irritancy: Sensitivity: Carcinogenicity

IARC:

NTP:

OSHA:

Reproductive Toxicity: Teratogenicity: Mutagenicity: Name of Toxicoligically Synergistic Products:

available.

Not available.

Silica Dioxide—Group 3. Not classifiable.

No components are listed.

Inhalation, Ingestion, Eyes, Skin.

Not available.

Not

Reactivity Data

Stability: Conditions to Avoid:

ignition.

Polymerization: Hazardous Decomposition or Byproducts:

Combustion products include harmful gases such as carbon monoxide and nitrogen oxides.

Incompatibility:

Stable in general.

Avoid excess heat and all sources of

Will not occur.

Not available.

9 - English

Preventive Measures ___________

Personal Protective Equipment Respiratory Protection:

spills, use dust respirator during cleanup.

Protective Gloves and/or Eye Protection:

normally required. For larg e spills, use rubber gloves and safety goggles during cleanup.

Engineering Controls Ventilation:

required.

Other Protective Equipment and/or Hygienic

Practices:

Spill Cleanup

Small Spills

1. Remove sources of ignition.

2. Carefully clean up the spill with a wet cloth, avoiding inhalation of fine dust.

Large Spills

1. Remove sources of ignition and keep unnecessary and unprotected personnel away from area.

2. Wear protective gear: respirator, rubber gloves, safety goggles.

3. Vacuum the spill, then wipe up re mainder with a wet cloth.

Waste Disposal

• Prevent release of material into natural waters and sewers.

• Follow appropriate federal, state and local regulations.

• Small amounts can be incinerated.

Careful! carbon monoxide and nitrogen oxides.

• Large amounts must be passed to a licensed waste contractor.

Precautions Precautions for Handling or Storage:

sun. Store in a cool room, under 104°F (40°C). Keep out of reach of children.

Other Precautions: Shipping Information

Special Shipping Information:

container carefully to avoid shock. Do not drop. Keep dry.

Outside of normal ventilation, not normally

None.

Combustion can create harmful gases such as

Not normally required. F or large

Not

Protect from the

None.

Non hazardous. Handle

User’s Responsibility ____________

Preparation Date of MSDS

Date:

November 20, 2012.

Prepared by:

Oki Data Americas, Inc. Engineering Services Department. 2000 Bishops Gate Blvd. Mt. Laurel, NJ 08054-4620

Tel: (856) 235-2600 Fax: (856) 222-5320 http://

WWW.OKIPRINTINGSOLUTIONS.COM

my.okidata.com

10 - English

Material Safety Data Sheet

#58388001

Cyan Toner: P/N 44844511

For more information, contact Oki Data at: 2000 Bishops Gate Boulevard, Mount Lau re l, NJ 08054-4620.

Emergency Information

Canada only.

Emergency First Aid Procedures

Toner swallowed (ingested)

Immediately seek medical attention. Never give anything by mouth to an unconscious person. If possible, rinse out mouth and give one or two glasses of water or milk to drink.

Toner inhaled.

Remove person to fresh air. Seek medical attention.

Toner gets in the eyes.

Flush eyes with large quantities of cool water for 15 minutes, keeping the eyelids open with fingers. If necessary, seek medical attention.

Toner gets on the skin.

Wash toner off the skin with plenty of cool water and soap. If necessary, seek medical attention.

Note:

Small amounts of toner on skin or clothing can easily be removed with soap and makes toner harder to remove.

Hazardous Ingredients

Silica dioxide (about 2% by weight)

CAS#: Trade Secret. OSHA PEL: Not established. ACGIH TLV: Not established. LD50: Not Available. LC50: Not Available.

Physical Data

Physical State: Melting/Freezing Point: Boiling Point: PH:

Not available.

Vapor Pressure: Vapor Density (Air=1): Evaporation Rate (Butyl Acetate=1): Specific Gravity (H2O=1): Solubility in Water: Solubility in Solvents:

toluene, chloroform and tetrahydrofuran.

Coefficient of water/oil Distribution: Appearance and Odor: Odor Threshold:

Solid.

Not available.

: call 1-800-654-3282; US and

cold

water. Hot water

Not available.

1.1 to 1.2 at 20°C (68°F).

Not available.

Some components are soluble in

Not available.

Cyan powder, no odor.

Not available.

Fire and Explosion Hazard Data ____

Minimal fire hazard. Large quantities may cause

risk of dust explosion. Flash Point (Method Used): Flammable Limits

Lower Explosive Limit:

Upper Explosive Limit: Auto-Ignition Temperature Explosion Data

Sensitivity to Mechanical Impact:

Sensitivity to Static Discharge: Extinguishing Media:

case of large fire, shut off air by spraying with water or foam.

Special Fire Fighting Procedures:

upwind position. Avoid inhalation of smoke or gases. Wear self-contained breathing apparatus.

Hazardous Combustion Products:

oxides of nitrogen.

In case of small fire, use CO2. In

Not applicable.

Not available.

: Not available.

Not available.

Fight fire from

Carbon monoxide,

Toxicological Properties

Routes of Entry: Effects of Acute Exposure: Effects of Chronic Exposure: Exposure Limits: Irritancy: Sensitivity: Carcinogenicity

IARC:

NTP:

OSHA:

Reproductive Toxicity: Teratogenicity: Mutagenicity: Name of Toxicoligically Synergistic Products:

available.

Not available.

Silica Dioxide—Group 3. Not classifiable.

No components are listed.

Inhalation, Ingestion, Eyes, Skin.

Not available.

Not

Reactivity Data

Stability: Conditions to Avoid:

ignition.

Polymerization: Hazardous Decomposition or Byproducts:

Combustion products include harmful gases such as carbon monoxide and nitrogen oxides.

Incompatibility:

Stable in general.

Avoid excess heat and all sources of

Will not occur.

Not available.

11 - English

Preventive Measures ___________

Personal Protective Equipment Respiratory Protection:

spills, use dust respirator during cleanup.

Protective Gloves and/or Eye Protection:

normally required. For larg e spills, use rubber gloves and safety goggles during cleanup.

Engineering Controls

Ventilation:

required.

Other Protective Equipment and/or Hygienic

Practices:

Spill Cleanup

Small Spills

1. Remove sources of ignition.

2. Carefully clean up the spill with a wet cloth, avoiding inhalation of fine dust.

Large Spills

1. Remove sources of ignition and keep unnecessary and unprotected personnel away from area.

2. Wear protective gear: respirator, rubber gloves, safety goggles.

3. Vacuum the spill, then wipe up re mainder with a wet cloth.

Waste Disposal

• Prevent release of material into natural waters and sewers.

• Follow appropriate federal, state and local regulations.

• Small amounts can be incinerated.

Careful! carbon monoxide and nitrogen oxides.

• Large amounts must be passed to a licensed waste contractor.

Precautions Precautions for Handling or Storage:

sun. Store in a cool room, under 104°F (40°C). Keep out of reach of children.

Other Precautions: Shipping Information

Special Shipping Information:

container carefully to avoid shock. Do not drop. Keep dry.

Outside of normal ventilation, not normally

None.

Combustion can create harmful gases such as

Not normally required. F or large

Not

Protect from the

None.

Non hazardous. Handle

User’s Responsibility ____________

Preparation Date of MSDS

Date:

November 20, 2012.

Prepared by:

Oki Data Americas, Inc. Engineering Services Department. 2000 Bishops Gate Blvd. Mt. Laurel, NJ 08054-4620

Tel: (856) 235-2600 Fax: (856) 222-5320 http://

WWW.OKIPRINTINGSOLUTIONS.COM

my.okidata.com

12 - English

Material Safety Data Sheet

#58388101

Black Toner: P/N 44844512

For more information, contact Oki Data at: 2000 Bishops Gate Boulevard, Mount Laurel, NJ 08054-4620.

Emergency Information

Canada only.

Emergency First Aid Procedures

Toner swallowed (ingested)

Immediately seek medical attention. Never give anything by mouth to an unconscious person. If possible, rinse out mouth and give one or two glasses of water or milk to drink.

Toner inhaled.

Remove person to fresh air. Seek medical attention.

Toner gets in the eyes.

Flush eyes with large quantities of cool water for 15 minutes, keeping the eyelids open with fingers. If necessary, seek medical attention.

Toner gets on the skin.

Wash toner off the skin with plenty of cool water and soap. If necessary, seek medical attention.

Note:

Small amounts of toner on skin or clothing can easily be removed with soap and makes toner harder to remove.

Hazardous Ingredients

Carbon Black (about 4% by weight)

CAS#: Trade Secret. OSHA PEL: Not established. ACGIH TLV:Not established. LD50: Not available. LC50: Not available.

Silica dioxide (about 2% by weight)

CAS#: Trade Secret. OSHA PEL: Not established. ACGIH TLV: Not established. LD50: Not Available. LC50: Not Available.

Physical Data

Physical State: Melting/Freezing Point: Boiling Point: PH:

Not available.

Vapor Pressure: Vapor Density (Air=1): Evaporation Rate (Butyl Acetate=1): Specific Gravity (H2O=1): Solubility in Water: Solubility in Solvents:

toluene, chloroform and tetrahydrofuran.

Coefficient of water/oil Distribution: Appearance and Odor:

Solid.

Not available.

: call 1-800-654-3282; US and

cold

water. Hot water

Not available.

1.1 to 1.2 at 20°C (68°F).

Not available.

Some components are soluble in

Not available.

Black powder, no odor.

Odor Threshold:

Not available.

Fire and Explosion Hazard Data

Minimal fire hazard. Large quantities may cause

risk of dust explosion. Flash Point (Method Used): Flammable Limits

Lower Explosive Limit:

Upper Explosive Limit: Auto-Ignition Temperature Explosion Data

Sensitivity to Mechanical Impact:

Sensitivity to Static Discharge: Extinguishing Media:

case of large fire, shut off air by spraying with water or foam.

Special Fire Fighting Procedures:

upwind position. Avoid inhalation of smoke or gases. Wear self-contained breathing apparatus.

Hazardous Combustion Products:

oxides of nitrogen.

In case of small fire, use CO2. In

Not applicable.

Not available.

: Not available.

Not available.

Fight fire from

Carbon monoxide,

Toxicological Properties

Routes of Entry: Effects of Acute Exposure: Effects of Chronic Exposure: Exposure Limits: Irritancy: Sensitivity: Carcinogenicity

IARC

NTP:

OSHA:

to OSHA 29 CFR 1910.1200.

Reproductive Toxicity: Teratogenicity: Mutagenicity: Name of Toxicoligically Synergistic Products:

available.

Not available.

Silica Dioxide: Group 3. Not classifiable. Carbon Black: Group 2B "Possible Carcinogen."

No components are listed.

Carbon black is designated hazardous according

Inhalation, Ingestion, Eyes, Skin.

Not available.

Not

Reactivity Data

Stability: Conditions to Avoid:

ignition.

Polymerization: Hazardous Decomposition or Byproducts:

Combustion products include harmful gases such as carbon monoxide and nitrogen oxides.

Incompatibility:

Stable in general.

Avoid excess heat and all sources of

Will not occur.

Not available.

13 - English

Preventive Measures ___________

Personal Protective Equipment Respiratory Protection:

spills, use dust respirator during cleanup.

Protective Gloves and/or Eye Protection:

normally required. For larg e spills, use rubber gloves and safety goggles during cleanup.

Engineering Controls Ventilation:

required.

Other Protective Equipment and/or Hygienic

Practices:

Spill Cleanup

Small Spills

1. Remove sources of ignition.

2. Carefully clean up the spill with a wet cloth, avoiding inhalation of fine dust.

Large Spills

1. Remove sources of ignition and keep unnecessary and unprotected personnel away from area.

2. Wear protective gear: respirator, rubber gloves, safety goggles.

3. Vacuum the spill, then wipe up re mainder with a wet cloth.

Waste Disposal

• Prevent release of material into natural waters and sewers.

• Follow appropriate federal, state and local regulations.

• Small amounts can be incinerated.

Careful! carbon monoxide and nitrogen oxides.

• Large amounts must be passed to a licensed waste contractor.

Precautions Precautions for Handling or Storage:

sun. Store in a cool room, under 104°F (40°C). Keep out of reach of children.

Other Precautions: Shipping Information

Special Shipping Information:

container carefully to avoid shock. Do not drop. Keep dry.

Outside of normal ventilation, not normally

None.

Combustion can create harmful gases such as

Not normally required. F or large

Not

Protect from the

None.

Non hazardous. Handle

User’s Responsibility ____________

Preparation Date of MSDS

Date: Prepared by:

November 20, 2012.

Oki Data Americas, Inc Engineering Services Department. 2000 Bishops Gate Blvd. Mt. Laurel, NJ 08054-4620

Tel: (856) 235-2600 Fax: (856) 222-5320 http://

WWW.OKIPRINTINGSOLUTIONS.COM

my.okidata.com

14 - English

Informations de sécurité, de garantie, et de

réglementation

• Si vous utilisez une rallonge électrique ou une barre

Informations sur la sécurité,

Modèles de 120 volts

Votre produit OKI a été conçue avec soin pour vous fournir des années de rendement sûr et fiable. Comme pour tout matériel électrique, un certain nombre de précautions de base doivent être observées pour vous protéger de toute blessure ou éviter tout dommage à le produit.

• Lisez attentivement les directives d'installation et d'utilisation fournies.

• Conservez tous les documents pour fins de référence future.

• Lisez et observez les avertissements et directives des étiquettes apposés sur le produit.

• Débranchez le produit avant de la nettoyer. Utilisez uniquement un chiffon humide; n'utilisez pas de nettoyants liquides ou en aérosol.

• Placez le produit sur une surface stable et solide. Sur une surface instable, le produit peut tomber et être endommagée. Évitez toute surchauffe de le produit. Ne la placez pas sur une surface souple, comme une couverture, un divan ou un coussin. Les aérateurs pourraient être obstrués et provoquer une surchauffe de le produit.

• Protégez le produit contre la surchauffe. Vérifiez qu'aucun aérateur n'est obstrué. Ne placez pas le produit sur une source de chaleur (p. ex. , radiate ur ou grille de chauffage) ou à proximité de celle ci. Protégez le produit contre les rayons du soleil.

• Utilisez toujours le produit dans un endroit bien ventilé. Prévoyez assez d'espace autour de le produit pour assurer une ventilation adéquate et un accès facile aux bacs à papier. Si vous placez le produit dans une armoire d'une quelconque nature, assurez-vous qu'elle est bien ventilée.

• N'utilisez pas le produit à proximité d'un point d'eau. Évitez de renverser quelque liquide que ce soit sur le pr oduit.

• Assurez-vous que la source d'alimentation correspond aux exigences indiquées à l'arrière de le produit. En cas de doute, communiquez avec votre détaillant ou fournisseur d'électricité.

• Ne branchez pas ce produit dans un système d'alimentation sans coupure. Pour plus d'information, contactez Oki Data au 1 800 OKI-DATA.

• Pour des raisons de sécurité, le produit possède une prise à trois broches de mise à la terre. Elle ne s'adapte qu'à une prise murale reliée à la terre. Si vous ne pouvez pas la brancher, votre prise de courant est sans doute un ancien modèle sans prise de terre. Communiquez avec un électricien pour la remplacer par une prise mise à la terre. N'utilisez pas d'adaptateur pour contourner la mise à la terre.

• Le produit doit être installée à proximité d'une prise de courant aisément accessible.

• Évitez d’endommager le cordon d’alimentation. Évitez de posez quoi que ce soit sur le cordon d'alimentation ou de le placer dans une zone de passage. Si le câble est endommagé ou effiloché, remplacez-le immédiatement.

d'alimentation avec le produit, assurez-vous que l'ampérage nécessaire à l'ensemble de l'équipem ent r elié est inférieur à l'ampérage maximum pris en charge par la rallonge. L'ampérage maximum de tout équipement branché sur une seule ligne électrique ne doit généralement pas dépasser 15 ampères.

• N'enfoncez aucun objet dans les fentes de ventilation situées sur les côtés de ll produit, au risque d’être électrocuté ou de provoquer un incendie.

• À l'exception de l'entretien de routine décrit dans la documentation, n'effectuez aucune réparation sur le produit. L'ouverture du capot peut vous exposer à des risques d'électrocution ou autres.

• N'effectuez aucun réglage autre que ceux indiqués dans la documentation. Vous pourriez provoquer des dommages à l'appareil nécessitant de lourdes réparations. La documentation fournie contient les informations requises pour faire réparer votre produit par des techniciens qualifiés Oki Data.

Si vous constatez le moindre signe indiquant le fonctionnement inadéquat de le produit ou que celle-ci a été endommagée, débranchez-la immédiatement et observez ensuite la procédure décrite dans la documentation fournie pour faire réparer le produit.

Vérifiez notamment les éléments suivants :

• Le câble d'alimentation est endommagé ou effiloché.

• Du liquide a été renversé dans le produit, ou le produit a été en contact avec de l'eau.

• Le produit est tombée ou son boîtier a été endommagé.

• Le produit ne fonctionne pas normalement après avoir suivi les directives d’utilisation.

15 - Français

+ 33 hidden pages

OKI C831 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety, Warranty and Regulatory Information

Limited Warranty, US and Canada

Regulatory Information