Ohsung Electronics URCMRZ260 Users Manual

Order Number : GETEC-C1-09-088 FCC Part 15 subpart C
Test Report Number : GETEC-E3-09-039 Page 1 / 1

APPENDIX H

: USER’S MANUAL

EUT Type: RF Base Station

FCC ID.: OZ5URCMRZ260

MRZ-260 Installation Manual

MRZ-260 Installation Manual ©2009 Universal Remote Control, Inc.

The information in this manual is copyright protected. No part of this manual may be
copied or reproduced in any form without prior written consent from Universal Remote
Control, Inc.

UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL,
TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL.

The Home Theater installation on the cover was designed and installed by Stone­Glidden of King of Prussia and Doylestown, PA.

The information in this manual may be subject to change without prior notice.

Complete Control is a registered trademark of Universal Remote Control, Inc.

All other brand or product names are trademarks or registered trademarks of their respec­tive companies or organizations.

500 Mamaroneck Avenue, Harrison, NY 10528

Phone: [phone] Fax: [phone]

T

ABLE OF CONTENTS

Introduction 1

Features and Benefits 2

Parts Guide 2

Installation 3

Testing 5

Front Blaster Overload 7

Disabling the Front Blaster - Step by Step via PC 7

Controlling Four Identical Components/Zones 8

Identical Components/Zones - Step by Step via PC 8

Programming For Multiple Equipment Locations 10

USA Limited Warranty Statement 11

Frequently Asked Questions 12

Specifications 12

Federal Communication Commission Interference Statement

13

Page 1

MRZ-260 BASE STATION

Introduction

The MRZ-260 base station has incorporated a new wireless technolo­gy referred to as Zigbee. This technology improves the range and reli­ability throughout a house and gives you the ability to control as
many identical components as needed. In order to control a Zigbee
base station an Zigbee remote is needed such as the MX-880Z.

3. Self-adhesive “Flashers” affix to
the Infrared sensors on the front pan­els of your components. The
Flashers relay commands to compo­nents out of sight of the MRZ-260
Front Blaster. The flashers plug in to
the MRZ-260 rear flasher line out­puts via their 10 foot cables.
Uniquely, the MRZ-260 can also
connect to components with rear
panel IR Inputs via its adjustable IR
Line Outputs.

2. The MRZ-260 built-in Front Blaster sends commands to com­ponents in the same cabinet space or you can use flashers.

1. The MX-880Z sends radio
waves in every direction, so you
don’t have to point the remote
anymore!

Page 2

MRZ-260 BASE STATION

Features and Benefits

Interference Rejection and Extended Range via Zigbee

The MRZ-260 receives Zigbee signals via its integrated receiver and anten­na and is the only wireless standards-based technology:

* allows omni-directional control
* enables broad-based deployment of wireless networks with low cost,

low power solutions.

* provides the ability to run for years on inexpensive primary batteries for

a typical home theatre application.

Two Fixed IR Outputs with RFTX URC Lighting Control

The MRZ-260 is equipped with two fixed IR line outputs with standard 3.5
mm jacks for standard and sleeved IR emitter/flashers. One Fixed IR Output
has a dual role for URC Ligting Control via the RFTX transmitter

Two Variable IR Outputs Match Rear Panel IR Inputs

The MRZ-260 is equipped with two adjustable IR line outputs. Each output
can be individually matched to rear panel IR inputs on any component that
is designed to be operated by a standard IR repeater. The outputs utilize a

3.5mm jack and are compatible with standard IR emitter/flashers as well.

No Limit Equipment Locations With Identical Components

Each MX remote is “addressable.” They can be programmed to specifically
control components in a particular room by installing an MRZ-260 base sta­tion at each location. In operation it’s simple: when you select a device
located in the Den, the MX remote only sends commands to the Den.
When you select a device located in the Family Room, the MX remote only
sends commands to it.

A Single MRZ-260 Can Control an Array of Identical Components or
Identical Zones of a Multi Zone Preamp/Matrix Switcher

Each MRZ-260 has four “addressable” IR Line Outputs. For example, you
can control up to four identical TV’s with one MRZ-260 or route volume
commands for a specific zone to a particular zone IR input on a multi-zone
preamp. If you have more than four identical components or zones, there
is no limit on how many MRZ-260s can be installed to control them (thus
allowing an unlimited amount of identical components or zones in one
house).

Parts Guide

The MRZ-260 RF Base Station includes:

1 - MRZ-260 Base Station
1 - Mounting Plate for wall mounting

the MRZ-260
4 - Screws for wall mounting
1 - 9V-300mA Power Supply
12 - Labels for IR Line Outputs

4 - Visible Flashers with 10 foot plug in

cables including 1 pink sleeved

emitter for the RFTX-1 port
4 - Extra self adhesive pads for Emitters
1 - Screwdriver for Variable Outputs