Ohlins HU 095, HUSABERG MX 2000 Mounting Instructions

Mounting instructions

HU 095 - HUSABERG MX 2000

Kit content

Shock absorber, Type 46PRCQ Hu095
Sticker Öhlins 00197-01 2
Sticker Memo note 01180-01 1
C.spanner 00710-02 1
Owners Manual

Setup data

Lenght 415 mm
Stroke 107 mm
Rebound adjustment 18 clicks
Compression adjustment 15 clicks
Preload 1 mm

Notes

HU 095, Issued 99 12 03

Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.

Phone [phone], fax [phone].

E-mail: [e-mail]

Traction, handling,
comfort and safety

NOTE!

Make sure that all bolts are tightened
to the correct torque and that nothing
fouls or restricts movement of the shock
absorber when the suspension is being
fully compressed or extended.

WARNING!

Certain modifications may be neces­sary when installing the Öhlins shock
absorber/suspension. It is essential that
the mounting instructions are carefully
followed.

Before you start

WARNING!

Installing a shock absorber, that is not
approved by the vehicle manufacturer,
may affect the stability of your vehicle.
Öhlins Racing AB cannot be held
responsible for any personal injury or
damage whatsoever that may occur
after fitting the shock absorber. Contact
an Öhlins dealer or other qualified
person for advice.

Öhlins Racing AB can not be held responsi­ble for any damage whatsoever to shock
absorber or vehicle, or injury to persons, if
the instructions for fitting and maintenance
are not followed exactly. Similarly, the
warranty will become null and void if the
instructions are not adhered to.

WARNING!

Please study and make certain that you
fully understand all the mounting instruc­tions and the owner´s manuals before
handling this shock absorber kit. If you
have any questions regarding proper
installation procedures, contact an
Öhlins dealer or other qualified person.

WARNING!

The vehicle service manual must be
referred to when installing the Öhlins
shock absorber.

NOTE!

Öhlins products are subject to continual
improvement and development. Con­sequently, although these instructions
include the most up-to-date information
available at the time of printing, there
may be minor differences between your
suspension and this manual. Please
consult your Öhlins dealer if you have
any questions with regard to the con­tents of the manual.

Safety signals

Important information concerning safety is
distinguished in this manual by the
following notations

The Safety alert symbol means:
Caution! Your safety is involved.

WARNING!

Failure to follow warning instructions
could result in severe or fatal injury to
anyone working with, inspecting or using
the suspension, or to bystanders.

CAUTION!

Caution indicates that special precautions
must be taken to avoid damage to the
suspension.

NOTE!

This indicates information that is of
importance with regard to procedures

Kit contents

Before installing the shock absorber,
please check the contents of the kit, listed
on the front page of this instruction. If any­thing is missing, contact your Öhlins
dealer.

NOTE!

During storage and transportation, es­pecially at high ambient temperature, the
oil and grease used for assembling may
run out inside the packing and damage
the expanded polystyrene packing ma­terial. This is not unusual and is in no
way detrimental to the shock absorber.

© Öhlins Racing AB.

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Öhlins Racing AB is prohibited.

Printed in Sweden.

WARNING!

1. It´s advisable to have an Öhlins
dealer or other qualified person to fit
your shock absorber.

2. Instructions in the vehicle service
manual are to be followed when
changing the shock absorber.

3. When working on a lifted vehicle it
must be securely supported to prevent
it from falling.

Mounting instructions
1

Put the motorcycle on a stand so the rear
wheel has ground clearance. Make sure
it´s steadily positioned and will not fall over.

2

Remove the seat by loosening the rear
attachment screws. Remove the side covers.

3

Loosen the lower and the upper attachment
of the original shock absorber and remove it.

4

Loosen the brake fluid reservoir.

5

Turn it 180° forwards and refit it.

6

Refit the parts taken away.

7

Continue your work according to the
Owner´s Manual, section Adjustments

180° Forward

2

4

5

3

Front