JAZ-ADP-GPIO Adapter and
JAZ-CBL-DB15 Accessory
Cable Instructions
JAZ-ADP-GPIO Adapter
This accessory converts the 20-pin GPIO connector on Jaz DPUs manufactured on January 1, 2008 to
the mini-HDMI connector used by the Jaz DPU GPIO (Jaz DPUs manufactured after January 1, 2008).
The mini-HDMI connector provides additional functionality such as triggering.
Note
In addition to the mini-HDMI connector provided on the JAZ-ADP-GPIO Adapter,
additional firmware is necessary to use some of the new functions. Upgrading this
firmware may require an RMA to return the unit to the factory as shown below:
Module Firmware Version Field Upgradeable?
DPU Blackfin DPU-GPIO uImage 22-SEP-09 or newer Yes
DPU FPGA 0x0085 or newer No
Spectrometer FPGA 0x0093 or newer No
Attaching the JAZ-ADP-GPIO Adapter
► Procedure
1. Unpack the connector. Your package should contain the following:
One JAZ-ADP-GPIO
Four 2-56 x 3/16” Phillips head screws to attach the adapter to the DPU module in your
Jaz stack. (Only two screws are needed; two extra screws are provided.)
013-40000-000-01-201102
JAZ-ADP-GPIO and JAZ-CBL-DB15 Instructions
2. Locate the DPU module in your Jaz stack.
3. Remove the screws currently attached to the DPU front panel
4. Use the new screws provided to attach the adapter to the DPU module as shown below:
5. Follow the instructions in Connecting the Accessory Cable to attach the accessory cable as
shown below:
Cable Pinouts
Pin # Function Description
1 GND Ground
2 RX RS-232 Data In
3 TX RS-232 Data Out
4 GND Ground
5 EXT_TRIG_IN 3.3v Logic
6 LAMP_ENABLE GP_OUT
7 SCL1
8 CONT_STROBE (3.3v Logic)
2 013-40000-000-01-201102
OOI use only. See the
information.
Jaz Data Sheet for more
Pin # Function Description
9 SINGLE_STROBE (3.3v Logic)
JAZ-ADP-GPIO and JAZ-CBL-DB15 Instructions
10 SDA1
11 SPI_CLK
12 SPI_CS
13 MOSI
14 MISO
15 GPIO4 (3.3v Logic)
16 GPIO5 (3.3v Logic)
17 GPIO6 (3.3v Logic)
18 5V_GPIO 5 volt accessory power
19 GPIO7 (3.3v Logic)
OOI use only. See the
information.
OOI use only. See the
information.
OOI use only. See the
information.
OOI use only. See the
information.
OOI use only. See the
information.
Jaz Data Sheet for more
Jaz Data Sheet for more
Jaz Data Sheet for more
Jaz Data Sheet for more
Jaz Data Sheet for more
JAZ-CBL-DB15 Accessory Cable
The Ocean Optics JAZ-CBL-DB15 is an accessory cable for the Jaz DPU modules that contain the
DPU GPIO (DPUs dated after January 1, 2008) and DPUs that have the JAZ-ADP-GPIO attached.
This 12-inch cable connects the 19-pin mini-HDMI accessory connector on the Jaz DPU GPIO (or the
JAZ-ADP-GPIO Adapter) and terminates in a DB15 connector.
Connecting the Accessory Cable
► Procedure
1. Connect the accessory cable to the 19-pin mini-HDMI connector on the Jaz DPU module.
013-40000-000-01-201102 3
JAZ-ADP-GPIO and JAZ-CBL-DB15 Instructions
2. Connect the other end of the cable (with the DB15 connector) to the accessory being used.
Cable Pinouts
DB15 Connector
4 013-40000-000-01-201102
Specifications
Specification Value
Cable length 305 mm (12 inches)
Internal conductors 15 x 26 AWG stranded copper
Rating: 30 Volts
Jacketing PVC, black
Rating: 300 Volts, VW-1
Connectors Molded, latching 19-pin MHDMI
Molded, superthin SVGA HD15, female
DB15 Mounting 2 x 4-40 thumbscrews
2 x 4-40 hex standoffs
JAZ-ADP-GPIO and JAZ-CBL-DB15 Instructions
013-40000-000-01-201102 5
JAZ-ADP-GPIO and JAZ-CBL-DB15 Instructions
6 013-40000-000-01-201102
Loading...