Oasis R1P Installation Manual
is a trademark of Oasis International.
est une marque déposée de Oasis International.
T E FLON is a registered trademark of E.I. Dupont.
T E FLON est une marque déposée de E.I.Dupont.
030099-300 REV D
© 2009 Oasis International
All rights reserved.
Tous droits réservés.
Under Sink
Chiller unit
Installation Instructions and
Use and Care Guide
For questions about features, suggested retail price,
o p e r a t i o n / p e r formance, parts, accessories or service,
call: 1-800-950-3226.
Or visit our website at:
www.oasiscoolers.com
Printed in Mexico
Imprimé au Mexique
Unité de refroidissement
sous l’évier
Instructions d’installation
et guide de soins et entretien
Questions sur les caractéristiques, prix de vente suggéré,
opération / rendement, pièces, accessoires ou service,
appelez au 1 800-950-3226.
Ou visitez notre site web
www.oasiscoolers.com
Table of Contents / Table des matières .... 2
This chiller unit is not a water purifier.
Ce refroidisseur n’est pas un purificateur d’eau.
Certified to
NSF/ANSI 61
Certifié pour
NSF/ANSI 61
Chiller safety
Your safety and the safety of others are very import a n t .
We have provided many important safety messages in this manual and on your appliance. A l way s read
and obey all safety messages.
This is the safety aler t symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will fo l l o w the safety aler t symbol and either the word “ D A N G E R ” or “ W A R N I N G ” .
These words mean:
You can be killed or seriously injured if you don’t i m m e d i a t e l y
fo l l ow instructions.
You can be killed or seriously injured if you don’t
fo l l ow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what can happen if the instructions are not fo l l o we d .
332
Table of Contents
CHILLER SAFETY..................................................................... 2
ASSISTANCE OR SERVICE...................................................... 3
INSTALLATION REQUIREMENTS.......................................... 3
Tools and Parts........................................................................... 3
Location Requirements............................................................ 4
Electrical Requirements........................................................... 4
Water Supply Requirements.................................................. 5
INSTALLATION INSTRUCTIONS............................................ 5
Install the Chiller........................................................................ 5
CHILLER USE........................................................................... 6
Setting the control..................................................................... 6
Draining the Chiller................................................................... 6
Reconnecting the Chiller......................................................... 6
BEFORE CALLING FOR SERVICE.......................................... 6
TROUBLESHOOTING.............................................................. 7
CHILLER WARRANTY............................................................. 7
Dealer Name _______________________________________________________________________________________________________
Address ___________________________________________________________________________________________________________
Phone Number_________________________________ Model Number_____________________________________________________
Purchase Date______________________________________________________________________________________________________
Installation Requirements
Pencil
Measuring tape
Utility knife
1
1 . Under sink Chiller unit
2. 4 feet of blue tubing
3. 2 easy to connect elbows
4. 2 “T” quick connect fitting
5. Check valve
6. 6 feet of white tubing
7. 1 wall mounting clip
8. 1 phillips screws #7
Tools Needed Parts Supplied
IMPORTANT:
Observe all governing codes and ordinances. Check location where the chiller will be installed. Proper installation is your responsibility.
Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with installation
specifications and with state and local plumbing codes.
Water connections use easy to connect fittings that do not require sealing compounds to keep them from leaking.
Assistance or Service
If you need assistance or service, first see “Tr o u b l e s h o o t i n g ”
s e c tion. Additional help is available by calling 1-800-950-3226.
Monday to Friday 8:00 a.m. - 6:00 p.m. (EST) or write:
Oasis international
222 East Campus View Blvd.
Columbus, OH 43235
Please include a daytime phone number in your correspondence.
For installation and service, call: 1-800-950-3226 or visit our
website at www.oasiscoolers.com.
Keep this book and your sales slip together for future
r e f e r e n c e . You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your appliance to
help you obtain assistance or service if you need it. You will
need to know your complete model number. You can find this
information on the model and serial number label.
Tools and Parts
2
4
3
5
6
7
8
Table des matières
SÉCURITÉ DU REFROIDISSEUR............................................ 8
ASSISTANCE OU SERVICE...................................................... 9
EXIGENCES LORS DE L’INSTALLATION................................9
Outils et pièces........................................................................... 9
Exigences concernant l’emplacement................................10
Exigences concernant l’électricité........................................10
Exigences concernant l’alimentation d’eau......................11
INSTRUCTIONS POUR L’INSTALLATION............................11
Installation du refroidisseur...................................................11
UTILISATION DU REFROIDISSEUR..................................... 12
Régler les contrôles..................................................................12
Vider le refroidisseur................................................................12
Reconnecter le refroidisseur..................................................12
AVANT D’APPELER................................................................ 13
QUESTIONS FRÉQUENTES................................................... 13
GARANTIE DU REFROIDISSEUR......................................... 14
10.Slowly turn on the water supply valve. Open faucet until
water flows for about one minute. Check all connections
for leaks.
11 . Plug in the chiller.
12 . Prior to drinking water from chiller, flush water
through the chiller for about 5 minutes.
54
Recommended Ground Method
IMPORTANT:
For best performance, allow a 2” (5 cm) space around the side and the top. Do not put any objects on top of the chiller that could
obstruct the fan.
1 4 . 7 5 "
( 3 7.46 cm)
10 . 3 0 "
( 2 6 . 1 6 cm)
8 . 7 2 "
(22.14 cm)
A 120-volt, 60-Hz, 15- or 20-amp, grounded electrical supply is required.
It is recommended that a separate circuit serving only your chiller unit
be provided. Use an outlet that cannot be turned on/off by a switch.
The chiller must be grounded. This appliance is equipped with a power
supply cord with a 3 prong ground plug. To minimize possible shock
hazard, the cord must be plugged into a mating, 3 prong, ground-type
outlet, grounded in accordance with all national and local codes and
ordinances. If a mating outlet is not available, it is the personal
r e s p o n s i b i l i t y and obligation of the customer to have a properly
grounded, 3 prong outlet installed by a qualified electrician.
3
1 . Chiller unit
2. Blue tubing included
with chiller
3. Faucet is required
(sold separately)
4. Cold water supply line
5. White tubing included
with chiller
6. Filtration
(sold separately)
7. Water supply fitting
(sold separately)
8. Filter inlet
9. Filter outlet
10 “T” quick connect fitting
11. Check valve
2
1
4
5
6
7
5
8
9
Location Requirements
Electrical Requirements
If local codes permit, the chiller feed line should be connected
to the cold water supply line with a ‘’T’’ water line connector
(sold separately). If you are using a filtration unit, the chiller
should be connected after the filters.
IMPORTANT: If local codes do not permit the use of the ‘’T’’
water line connector, special feed valves can be obtained from
your local plumbing supply retailer.
Caution: The feed valve must allow water to flow back into the
building’s water supply piping to avoid extreme pressure building
up as the water is chilled. Failure to relieve this pressure will
damage t he chiller system and result in a water leak.
The water pressure to the chiller should be between 30 psi (MIN )
and 100 psi (MAX).
Installation Instructions
6 b . If you are NOT installing a filtration system, connect blue
tubing between the”water out” chiller tube and faucet, sold
s e p e r a t e l y . Do NOT use “T” quick connect fittings (part 10) or
check valve (part 11 ) .
7. Cut 6 inches of white tubing. Connect one end to “T”
( p a rt 1 0) that is connected to “water out” chiller tube and
other end to check valve inlet ( see figure 2).
8. Cut white tubing to connect the water supply fitting
(part 7) and the inlet of the filtration system. Connect the
straight-thru ports of the second “T” (part 10) to the loose
ends of the white tubing just cut. (see figure 3)
9. Connect white tubing included with chiller between the third
port of the second “T” (part 10) and check valve outlet (see
figure 3).
Figure 2
Water Supply Requirements
Install the Chiller
10
10
11
Figure 1
Figure A Figure B Figure C
Check valve
( p a rt 11 )
White tubing
to check valve
Blue tubing to faucet
“T” Quick connect fitting
( p a r t 10 )
Connection to Chiller
water “out”
Figure 3
Check valve
(part 11)
White tubing
to filtration system
Connection to part 7
“T” Quick
connect fitting
( p a rt 10 )
p a r t 10
p a r t 7
p a r t 10
NOTE: Tubing must be cut to fit. All tubes must be cut squarely
with no burrs. All tubing connections must be fully seated.
Tubing must be routed to avoid sharp bends and have enough
slack to avoid straining connections. A P-clip and mounting
screw are included to hold the tubing in place as needed. Pull
gently on each connection to make sure they are secure.
IMPORTANT: After chiller is unpacked, place chiller upright for
24 hours before plugging it in.
1 . Determine where you will install your chiller.
See ‘’Location Requirements’’ section.
2 . For best performance, allow a 2” (5 cm) space around
the side and the top. Do not put any objects on top of
the chiller that could obstruct the fan.
3. Shut off water supply valves.
4. Install faucet (sold separately).
See faucet’s Installation instructions.
5. Cut a piece of white tubing to connect the chiller (water in)
to the water supply fitting (part 7) or filter outlet (if applicable) .
(see figure 1)
NOTE: If you are installing the chiller and a filtration system
without a bladder tank, follow steps 6a to 12. Following these
steps will avoid the possibility of excessive pressure building as
the chiller cycles on and off. If you are installing a bladder tank
with your filtration system, the bladder tank must be connected
directly to the chiller without any regulators or back flow
p r e v e n t e r s between them. If you are NOT installing the chiller
with a filtration system or if your filter system includes a bladder
tank, follow steps 6b. and 10 to 12.
6 a . Connect “T” (part 10) to “water out“ chiller tube. Connect blue
tubing between “T” and faucet, sold separately. (see figure 2)
How to insert/remove tubing in easy connect fitting
Insert the tubing squarely. See figure A.
Make sure to insert tubing completely. See figure B.
Push in collet and pull out tubing. See figure C.
Loading...