Oasis Quasar PWEBQ, Quasar P EBQ, Quasar PWF2EBQ, Quasar PG8EBQ, Quasar PG8F2EBQ Installation Instructions Manual

Water Coolers

QUASAR Hands-Free Bottle Filler

UVC-LED WATER TREATMENT

Model PWEBQ and PWF2EBQ (retro fit)
and P*EBQ Family of Drinking

Fountains/Bottle Filler combo

Installation Instructions

The Hands-Free Bottle Filler mounts directly above Versacooler® I and II
products. If the cooler electrical outlet does not have two useable plugs, an
outlet splitter will need to be used.

If installed onto a refrigerated cooler, chilled water can be dispensed through
the Bottle Filler. Otherwise, room temperature water will be dispensed.

The Bottle Filler is shipped partially assembled.

On the combo units, the cooler is plumbed and ready to attach to the Bottle
Filler.

When completed, the finished assembly will look like this:

OR

1

Section 1: Getting Started

What’s Included:

Top C ap

Quasar Hands-Free

Bottle Filler

38” of ¼ OD plastic
tubing with 19” of
sponge tubing
insulation (included

with “Quasar Bottle
Filler ready” coolers)

Snap bushings 7/8”

and 1½”

Quick connect tee

fitting

Installation
instructions

Rubber
Gasket

Versafilter II

The Versafilter II and remedi filter are only
included in the PWF2EBQ model.

remedi

filter

Tool s required:

Ø 3/8” pilot drill and either a step drill bit up to 7/8” diameter that will drill

through SS top or 7/8” diameter punch die (retrofit version only)

Ø Electric drill; wrench for punch die

Ø Small tubing cutter for copper tube

Ø 1/4“ nut driver

Ø # 2 Phillips screw driver

Ø #15 torx bit driver

2

Section 2: Rough In Drawing

Oasis PWEBQ: Versacooler® II Models PAC, P8AC with Hands-Free Bottle Filler

3

Section 2: Rough In Drawing

Oasis PWEBQ: Versacooler® II Split Level Models with Hands-Free Bottle Filler

* On split level models, the Bottle Filler must be mounted on the

low unit in order to meet ADA guidelines.

4

Section 3A: Installation

Note: Proceed to Section 3B Step 5 “Final steps for both product families” if
the cooler is purchased “Quasar Bottle Filler or VersaFiller ready”.

A: Drilling hole in the top for water line connection.

1. Disconnect power by UNPLUGGING unit. It might be necessary to remove
the front panel to get access to the power.

2. Turn OFF water supply to the unit. It might be necessary to remove the
front panel to access the water stop valve.

3. Place hole template onto cooler top so it is aligned with the left side of unit
and wall. SEE NEXT PAGE FOR TEMPLATE

4. Mark hole location

5. Remove top from unit.

Mark hole location.

Template

Remove top from cooler by
removing six, #15 torx head screws
on sides of top.

6. Using a step drill bit or 7/8” punch die, make a 7/8” hole through top. You
may want to drill a pilot hole to get these started.

7. Install snap bushing into hole to protect tubing from being cut.

Install bushing

Drill

5

5

ALIGN THIS EDGE

WITH LEFT EDGE OF

COOLER TOP

Mark this center point on the

top. Remove the top from the

cooler. Then create a 7/8”

diameter hole through the top

at the marked center point

(step drill bit or punch die).

paper

3-1/4”

from

edge of

edge of

paper

AGAINST WALL

2-1/8”

from

PLACE THIS EDGE

USE THIS TEMPLATE TO MARK THE
HOLE LOCATION ON COOLER TOP

6

Section 3B: Installation

VersaCooler to Quasar Bottle Filler Plumbing Diagram

OPTIONAL

VERSAFILTER II

INLINE

STRAINER,TUBE,

AND REDUCER FTG.

PROVIDED WITH

FOUNTAIN.

OPTIONAL

FILTER

BOTTLE FILLER

SOLENOID

VALVE

UV LED

BUILDING

INLET WATER

VERSACOOLER

7

Section 3B: Installation

Two VersaCoolers to Quasar Bottle Filler Plumbing Diagram

BOTTLE FILLER

OPTIONAL

VERSAFILTER II

OPTIONAL

FILTER

SOLENOID

VALVE

VERSACOOLER

UV LED

VERSACOOLER

INLINE

STRAINER,TUBE,

AND REDUCER FTG.

PROVIDED WITH

FOUNTAIN.

BUILDING

INLET WATER

T-FITTING

8

Section 3B: Installation

B: Connecting the water line

Note: If you are retrofitting the Bottle Filler to an existing
cooler, follow the instructions starting on page 11.

For the single “Bottle Filler ready” cooler, the tube to connect to the Bottle
Filler is found inside the access panel (the compressor compartment). This

tube supplies cold water from the cooling tank to the Bottle Filler.

¼” OD tube to connect
to Versafiller

For split level “Bottle Filler ready” coolers, the tube to plumb in the Bottle
Filler is packaged in the dummy unit.

Remove tube from bag.

First, remove plug from
fitting on tank drain

Next, insert end of
tube into fitting.

9