Numark CDMIX3 Quick Start Manual
Professional CD Mixing Console
Quick Start Owner’s Manual
Manual de inicio rápido del
usuario
(ESPAÑOL)
Schnellbedienungsanleitung(DEUTSCH)
Manuale Rapido di Utilizzazione(ITALIANO)
Guide d’utilisation simplifié (FRANÇAIS)
CONTENU DE LA BOÎTE
• STATION DE MIXAGE CDMIX3
•
ADAPTATEUR DE COURANT
CONTENIDO DE LA CAJA
• ESTACIÓN DE MEZCLAS DE CD CDMIX3
• ADAPTADOR DE CORRIENTE
CONTENUTO DELLA CONFEZIONE
• CD MIXING STATION CDMIX3
•
ADATTATORE
BOX CONTENTS
• CDMIX3 CD MIXING STATION
•
POWER ADAPTER
BOX CONTENTS
• CDMIX3 CD MIXING STATION
•
POWER ADAPTER
CDMIX3 QUICK SETUP
1. Make sure all items listed on the front of this guide
are included in the box.
2. READ SAFETY INSTRUCTION BOOKLET BEFORE
USING THE PRODUCT.
3. Study this setup diagram.
4. Place CDMIX3 station in an appropriate position for
operation.
5. Make sure all devices are turned off and all faders
and gain knobs are set to “zero”
6. Connect all stereo input sources as indicated in the
diagram.
7. Connect the stereo outputs to power amplifier(s),
tape decks, and/or other audio sources.
8. Plug all devices into AC power.
9. Switch everything on in the following order:
• audio input sources (i.e. turntables or CD
players)
• CDMIX3
• last, any amplifiers or output devices
10. When turning off, always reverse this operation by,
• turning off amplifiers
• CDMIX3
• last, any input devices
11. Go to http://www.numark.com
for product
registration.
More information about this product may be found at
http://www.numark.com
REAR CONNECTIONS
1. Channel Inputs: Unbalanced RCA jacks for
connecting external sources. The Phono/Line input is
selected using the toggle switch on the front panel.
Turntables, HiFi VCRs, cassette and reel-to-reel tape
decks, DAT machines, CD players, laser discs, tuners,
even synthesizers or other mixing consoles can be
connected using these jacks. NOTE: Plug mono audio
sources into both left and right inputs using a “Y”
cable connector.
2. GND: This screw connector should be used to connect
any turntables or other devices that need to be
grounded.
3. Line/Phono Input Switch: Use this to allow either
line level or phono level equipment to be plugged into
your channel inputs. When Phono input is selected,
your signal is fed directly to the high-quality RIAA
phono pre-amplifiers. Use this position only for
turntables. Line level sources will overload the
sensitive phono pre-amps and will sound very bad, so
always be sure to toggle the line/phono switch over to
line before connection of line sources.
4. Third Line Input: Plug in a third line level device
such as a tape deck or additional CD player here.
5. Stereo Master Outputs: Unbalanced RCA connectors
controlled by the Master fader.
6. Stereo Balanced Master Outputs (XLR): lowimpedance XLR type connectors controlled by the
Master fader.
7. Mic Input: Plug your 1/4” Microphone plug in here.
8. AC In: This mix station is designed to work with the
power supply cord that comes with the unit. While the
power is switched off, plug the power supply into the
mix station first, then plug it into the outlet.
9. Power Switch: Use this switch to turn on the mix
station after all input devices are already connected to
prevent damage to your equipment. Turn the station
on before you turn on amplifiers and turn off
amplifiers before you turn off the mix station.
FRONT PANEL FEATURES
1. Input Fader: Controls individual source levels in
the mix.
2. Input toggle switch - Selects which source will be
live to that channel based on what you have
connected to the rear panel input section
3. 2-Band Stereo Equalizer (EQ) - compensates for
differences in source material sound quality.
4. Replaceable Crossfader - Achieves clean segues
between the two input channels. "Hard left" selects
Channel 1. "Hard right" selects Channel 2. With the
crossfader centered, both assigned channels are
live. Use the crossfader for fast and seamless
segues from one selected channel to the other
Note: The crossfader is user replaceable in case of
failure. Simply unscrew the two large screws which
hold it in place, lift it out and disconnect it’s cable.
Re-attach the new crossfader and screw the
mounting plate back onto the unit - you’re back in
business!
5. Fader Start – Activation allows you to start the CD
players from you crossfader. Travel from left to right
will start the right CD player and pause the left CD
player
6. Mic Input Fader – Adjusts microphone level.
7. Mic 1 Equalizer (EQ) – Adjusts microphone 1
treble and bass levels.
8. Master Stereo EQ – Adjust final master ouput
equalization of trevle, middle, and bass levels.
9. Master Fader – Controls the overall outuput level.
10. Stereo/Mono Toggle – Changes the master
output between Mono and Stereo.
11. LED METER - Indicates the Master output level.
12. Channel Monitor Selector – Used to route channel
audio to your headphones for cueing.
13. Cue Mix Control – Adjusts the headphone blend of
master output (PGM) and monitor (CUE) sound.
14. Headphone Level – Adjusts cue volume.
15. Headphone Jacks – Used to connect either 1/8” or
1/4” plugs for audio monitoring with headphones.
CD PLAYER FEATURES
1. OPEN/CLOSE (Disc Tray Open/Close) - Press to
load or eject the disc. Each press will open or close
the disc tray on the transport. NOTE: Tray will not
open unless the disc has been paused. Tray will
automatically close after 30 seconds.
2. TIME (Time Button) - Switches the time display
between elapsed playing time and remaining time
on the track and remaining time on the entire CD.
3. CONT/SING - Will cause just a single track to play
or all tracks in order by pressing once or twice.
4. LCD DISPLAY - Indicates all the functions, as they
are occurring, with the CD. These functions are
explained in the next section.
5. TRACK (Track Buttons) - Used to select the track
to be played.
6. Folder/ +10 – Selects folder from which tracks are
to be played. On a disc which contains no folders,
this button is used to advance tracks in increments
of 10
7. PROGRAM - Depress this button and the unit will
stop and the program indicator will light. Select
each track to be programmed and press the
PROGRAM button between selections. You can
program up to 30 tracks. Press PLAY to start the
program. To exit and erase program, either hold
the program button down for more than 2 seconds
while the unit is stopped, open the disc tray, or turn
off the power.
8. PITCH (Pitch Button) - Activates the Pitch Slider.
To alternate between ±8% and ±16%, press and
hold PITCH button. LED will indicate active setting.
9. PITCH SLIDER - The pitch can be changed up to
±16% by pressing the PITCH button so the PITCH
LED is lit, then moving the sliding fader. The pitch
will not be changed if the PITCH LED is off.
10. SEARCH WHEEL (OUTER RING) - 3 forward and 3
reverse speed positions for searching through
songs. The more you turn the wheel in either
direction the faster you search through the music.
11. PITCH BEND/JOG WHEEL (INNER RING) - The
jog wheel serves 2 functions depending on the
current mode.
a) The jog wheel will control a slow frame
search when the CD is not playing. To set a
new frame cue point, spin the wheel then
press play when you have determined the
proper position. Press CUE to return to the
“CUE POINT”.
b) When both CD players are playing a CD, the
pitch bend function allows the positioning of
the bass beats to be matched after the pitch
of each disc is matched. Either player can
“catch up” or “fall back” to match the other
player. The jog wheel will temporarily bend
the pitch of the music if the song is already
playing by rotating the wheel clockwise to
speed up or counterclockwise to slow down.
By changing the pitch of one disc with
respect to the pitch of the other disc, the
beats can be matched.
12. CUE - Pressing the CUE button during play provides
a return to the position at which play was started.
If PAUSE is used before CUE, that will become the
cue point. Alternately pressing the PLAY button and
the CUE button allows the CD to be played from the
same position any number of times. The CUE LED
will light up from the time the CUE button is pressed
until the CD has been reset to the position at which
play was started. Steady lighting of this LED
indicates the ready condition.
13. START/PAUSE (Play/Pause Button) - Each
press of the Play/Pause Button causes the operation
to change from play to pause or from pause to play.
14. LOOP IN – Used for setting a start loop point and
new cue points during playback.
15. LOOP OUT – Used for setting the end loop point
and releasing the loop action.
16. RELOOP / STUTTER – Depending on mode, as
explained further, this button is used for either
repeating a previously set loop or seamlessly
stuttering on the last set cue point.
LCD DISPLAY FEATURES
1. PAUSE: Active when the unit is paused.
2. PLAY: Active while a CD is playing.
3. CUE: Flashing when the unit is setting a cue point.
Lit continuously when the unit is paused at a cue
point.
4. PROGRAM: Used for pre-programming the track
order to automatically be played by the unit. This is
a great function if you need to leave the CD player
alone.
5. TIME MODE: (Elapsed) is for showing time as it is
taking place.(Remain) shows how much time is left
on a particular track. This function is controlled by
the TIME BUTTON.
6. TIME BAR: Shows either time remaining or
elapsed depending on the setting of the TIME
BUTTON.
7. TRACK NUMBER: Shows the current track that the
unit is playing. While searching folders, the selected
folder is displayed, denoted by the letter F.
8. TRACK: Lights while unit is in Track Play mode.
9. SINGLE: Shows when the unit is set to play just
one track at a time. When this is not lit, the CD will
play continuously through all tracks. This function is
controlled by the SING/CONT BUTTON.
10. MP3: Lit when unit is playing an MP3 file.
11. MINUTES: Shows the minutes elapsed or
remaining depending on mode setting.
12. SECONDS: Shows the seconds elapsed or
remaining depending on mode setting.
13. FRAMES: The CD Player breaks down a second into
75 frames for accurate cueing. This shows the
frames elapsed or remaining depending on mode
setting.
14. LOOP: Indicates when loop is actively playing.
15. PITCH: Shows the percentage change in pitch.
16. PITCH: Is lit when the PITCH BUTTON is active.
17. MATRIX DISPLAY: Displays CD Text or MP3 Tag
information. If reading a disc with no encoding,
display will read “NO TEXT”. Also displays folder
names while searching through folders.
PLAY / PAUSE & CUE OPERATIONS
PLAY & CUE
Back Cue Operation
Play Interval
Press "PLAY/PAUSE"
to start music
Press "CUE" return to
last starting point
Position on Disc
Pressing the “PLAY/PAUSE” button starts the disc. Pressing the “CUE” button will reset the disc to the last place where the disc was
started. This is called the cue point. By alternately pressing the “PLAY/PAUSE” button and the “CUE” button, the disc may be returned
and played from the cue point any number of times. This function is called back cue.
PLAY, PAUSE & CUE
Back Cue Operation
Play Interval Play Interval
Press "PLAY/PAUSE"
to start music
Press "PLAY/PAUSE"
to start music
Press "CUE" return t
o
last starting point
Press "PLAY/PAUSE"
to pause music
Position on Disc
When play has been paused and then started again, the return position for the back cue will be updated to this new position.
EDITING CUE POINT
Back Cue Operation
Play Interval
Press "PLAY/PAUSE"
to start music
Adjust the "CUE" point
with the jog wheel
Press "CUE" return to
last starting point
Position on Disc
When the inner dial is turned while a cue point is set, a new cue point can be located. The CD player will repeatedly play small parts of the
CD as you move it to the desired position. By pressing “PLAY/PAUSE” then “CUE” you can confirm that the new cue point is desirable.
USING THE FOLDER SEARCH FEATURE
One way to organize the MP3 files on your CD’s is by using Folders. Folders make it easier to find the music you want quickly. The
CDMIX3 is set up to navigate folders, making it the ideal tool for the professional DJ.
Note that the Track +10 feature is not available when a disc that contains folders is inserted into the drive. This feature is only used
with discs that do not contain folders.
The CDMIX3 Folder Search feature is easy to use.
1. Place an MP3 CD that contains folders into one of the CDMIX3’s two CD drives.
2. When the Disc is ready, the LCD display will change from “READ” to displaying the folder name.
3. Press the FOLDER button. The LCD display will flash “FOLDER”. Use the TRACK search buttons to scan through the
named folders contained on the disc. Press the FOLDER button again to select a folder. LCD display will flash “TRACK
LIST”.
4. You may now search tracks contained within the selected folder using the TRACK search buttons to scan through the
tracks contained within the folder.
MATCHING THE BEATS PER MINUTE (BPM)
Match the tempo by monitoring the music of both PLAYER 1 and PLAYER 2 by ear and adjusting the pitch. When the tempo of the music of
the selected CD player is slow compared to the tempo of the other player, move the slider to the ( + ) side and match the tempo. When
faster, move the pitch slider to the ( - ) side. The following illustration shows the case of matching the pitch of PLAYER 2 to the pitch of
the music being played on PLAYER 1.
1. Press PLAY/PAUSE to start PLAYER 1.
PLAYER 1 is playing
2. Press PLAY/PAUSE to start PLAYER 2
Both CD players are playing discs.
3. Listen to PLAYER 2 in your headphones. If the beat of channel 2 (in the headphones) is faster than channel
1, slow down the beat of channel 2 using the pitch control.
4. If the beat of channel 2 (in the headphones) slower than the beat of channel 1, speed up the beat using the
pitch control.
BEAT MATCHING USING PITCH BEND
If you find the BPM’s (Beats Per Minute or Tempos) are the same, however, the drum beats are not matched you will need to
temporarily change the pitch. The illustration below shows how to match the beat of PLAYER 2 to the beat of the music being played
on PLAYER 1. (This procedure can be done on either PLAYER).
After matching the BPM’s adjust the pitch temporarily as follows:
When PLAYER 2 is rotate the jog wheel counter clockwise
When PLAYER 2 is behind rotate the jog wheel clockwise
The pitch changes automatically while the jog wheel is rotated. The faster you rotate the wheel the more you change. Releasing the
wheel results in a return to the original pitch. (So the BPM’s are once again the same.)
EXAMPLE OF MIXING USING BOTH PLAYERS OF YOUR CD PLAYER
While playing a disc on PLAYER 1, load a disc into PLAYER 2 and select your next track, match its pitch to the track playing on
PLAYER1 and when you are ready use the crossfader on your mixer to fade from PLAYER 1 to PLAYER 2.
PLAYER 1
Load a disc and pres s the
OP EN/C LOS E b utto n.
PLAYER 2
Load a disc and pres s the
OP EN/CLOSE bu tton.
PLAYER 2
Press the Pause button ofPLAYER 2.
PLAYER 2
Liste n with the monitor and
press the play button.
PLAYER 2
With a matching downbeat from
Player 1 press the play button.
PLAYER 1
Se lect th e tra ck to be playe d.
PLAYER 2
Se lect th e tra ck to be playe d.
PLAYER 2
Rapidly sea rch fora cue point using
the oute r whe el
PLAYER 2
Press the cue button then play to be
sure of the se t cue point.
PLAYER 2
Ifyou are bea t mixing, turn on your
Pitch ad jus t and follow th e directions
for beat matching.
Load a disc in PLAYER 1 and
select the track and press PLAY.
Load a disc in PLAYER 2 and
select the track then play.
Set and edit a start cue point on
PLAYER 2
Check your new cue point
Do a MIX!
PLAYER 1
Pre ss the PLAY butto n
PLAYER 2
Pre ss the PLAY butto n
PLAYER 2
Slowly se t the right cue point
usingthe inner wheel
PLAYER 2
Re se t the pla ye r to the Cue point
by pres sing Cue
MIXE R
Whenyouarehappywithyourmix
move the cros sfa de r acc ordingly.
INSTALACIÓN RÁPIDA DEL CDMIX3 (ESPAÑOL)
1. Asegúrese de que todos los artículos incluidos al
inicio de este manual están incluidos en la caja.
2. LEA EL FOLLETO DE INSTRUCCIONES DE
SEGURIDAD ANTES DE UTILIZAR EL
PRODUCTO.
3. Estudie este diagrama de instalación.
4. Coloque la estación de mezclas en una posición
adecuada para su funcionamiento.
5. Asegúrese de que todos los dispositivos están
apagados y de que todos los faders y
potenciómetros de ganancia están en posición
“cero”.
6. Conecte todas las fuentes de entrada al estéreo
como se indica en el diagrama.
7. Conecte las salidas del estéreo a los amplificadores
de alimentación, unidades de cinta magnética y/o
otras fuentes de audio.
8. Enchufe todos los dispositivos al suministro de
corriente alterna.
9. Prenda todo en el siguiente orden:
• fuentes de entrada de audio (por ej.
giradiscos o reproductores de CD)
• CDMIX3
• por último, cualquier amplificador o
dispositivo de salida
10. Al apagar, realice siempre esta operación al
contrario:
• apague los amplificadores
• CDMIX3
• por último, cualquier dispositivo de entrada
11. Visite http://www.numark.com
para registrar el
producto.
Puede encontrar más información sobre este
producto al visitar http://www.numark.com
CONEXIONES TRASERAS
1. Entradas de canal: Jacks RCA no balanceados para
la conexión de fuentes externas. La salida de
Phono/Línea es seleccionada utilizando el interruptor
de palanca del panel delantero. Giradiscos,
reproductores de video de alta fidelidad (HiFi),
casetes y unidades de cinta magnética reel-to-reel,
máquinas DAT (Digital Audio Tape), reproductores
de CD, discos láser, sintonizadores e incluso
sintetizadores u otros instrumentos pueden ser
conectados utilizando estos jacks. NOTA: Enchufe
las fuentes de audio mono en ambas entradas,
derecha e izquierda, usando un cable conector tipo
“Y”.
2. GND: Este conector de tornillo debe ser usado para
conectar cualquier giradiscos u otro dispositivo que
tiene que ser conectado a tierra.
3. Line/Phono Input Switch: Haga uso de este
interruptor para dejar que el equipo de nivel de
línea o nivel de phono pueda ser enchufado en sus
entradas de canal. Cuando se seleccione la entrada
de phono, su señal introducida directamente a los
pre-amplificadores phono RIAA de alta calidad.
Utilice esta posición solo para giradiscos. Las
Fuentes de nivel de línea sobrecargarán los preamplificadores de phono sensibles y tendrá un
sonido de muy mala calidad, así que asegúrese
siempre de conmutar el interruptor de línea/phono a
línea antes de conectar las fuentes de línea.
4. Third Line Input: Plug in a third line level device
such as a tape deck or additional CD player here.
5. Stereo Master Outputs: Unbalanced RCA
connectors controlled by the Master fader.
6. Salidas Master Balanceadas de Estéreo (XLR):
conectores tipo XLR de baja impedancia controlados
por el Master fader.
7. Salida de micro (Mic): Enchufe su micrófono de
¼” aquí.
8. AC In (Entrada de corriente alterna): Esta
estación de mezclas está diseñada para trabajar con
el cable de suministro de alimentación que
acompaña a la unidad. Mientras que la alimentación
esté apagada, enchufe primero el suministro de
alimentación a la estación de mezclas y luego
enchúfelo a la toma de corriente.
9. Interruptor de alimentación: Use este
conmutador para prender la estación de mezclas
después de que todos los dispositivos de entrada
hayan sido conectados para evitar daño a su equipo.
Prenda la estación de mezclas antes de prender los
amplificadores y apague los amplificadores antes de
apagar la estación de mezclas.
LAS CARACTERÍSTICAS DEL PANEL FRONTAL
1. Fader de entrada: Controla los niveles de fuente
individuales del mezclador.
2. Interruptor de palanca de entrada: Selects
which source will be live to that channel based on
what you have connected to the rear panel input
section
3. 2-Band Stereo Equalizer (EQ) - compensates for
differences in source material sound quality.
4. Crossfader reemplazable – Consigue segues
limpios entre los dos canales de entrada.
“Completamente hacia la izquierda” selecciona el
canal 1. “Completamente hacia la derecha”
selecciona el canal 2. Con el crossfader en el centro,
ambos canales están activos. Use el crossfader para
segues rápidas y uniformes de un canal
seleccionado a otro.
Nota: El crossfader puede ser reemplazado por el
usuario en caso de fallo. Simplemente, desatornille
los dos tornillos grandes que lo sujetan, sáquelo
hacia fuera y desconecte el cable. Vuelva a sujetar
el nuevo crossfader y atornille la placa de montaje
de nuevo en la unidad – ¡ya puede volver al trabajo!
5. Activador del Fader (Start) – La activación le
permite poner los reproductores de CD en
funcionamiento desde su crossfader. Al desplazarlo
de izquierda a derecha, activará el reproductor de
CD de la derecha y desactivará el reproductor de CD
de la izquierda.
6. Fader de entrada de micro – Ajusta el nivel del
micrófono.
7. Mic 1 Equalizer (EQ) – Adjusts microphone 1
treble and bass levels.
8. Master Stereo EQ – Adjust final master ouput
equalization of trevle, middle, and bass levels.
9. Master Fader – Controls the overall outuput level.
10. Stereo/Mono Toggle – Changes the master
output between Mono and Stereo.
11. MEDIDOR LED – Indica el nivel de salida del
master.
12. Channel Monitor Selector – Used to route channel
audio to your headphones for cueing.
13. Cue Mix Control – Adjusts the headphone blend of
master output (PGM) and monitor (CUE) sound.
14. Nivel de auriculares- Ajusta el volumen de cue.
15. Conector de auriculares – Utilizado para conectar
clavijas de 1/8” o 1/4” para el monitoreo de audio
con los auriculares.
Loading...