Northstar NS100 RADIO INSTALLATION SHEET
Radio Installation Sheet
for NS100 VHF system
w w w.NorthstarNav.com
Parts Checklist
SINGLE SYSTEM
(NS100SS)
1 x VHF Black Box Radio
(single)
DUAL SYSTEM
(NS100DS)
1 x VHF Black Box Radio
(dual)
1 x Hailer Cable
ADDITIONAL WITH
EACH SYSTEM
1 x Hand set with cord (US)
1 x Mic Plate - black
1 x Black Box to Speaker
cord with Female-Female
Adapter
3 x SS self tapping screws
1 x Mic Clip with magnet
2 x SS self tapping screws
for mic clip
1 x Large Speaker
1 x Speaker Gasket
4 x Speaker tabs
4 x SS self tapping screws
4 x SS self tapping screws
1 x Power Cable w/tags
1 x SS Grounding screw
1 x Spare 10A fuse
1 x Mounting Template
- Black Box
PART CODE
APNSBB2E8070
PART CODE
APNSBB2E8080
PWNSBB2E7120
PART CODE
APNSBB2E8030
MMNSBB2E4000
WALI 08L07KX0
WALI08F08F0
MS35-20SPSX1
APNSBB2E8050
MS35-20TSPX1
APNSBB2E8060
MPNSBB2E7040
PPNSBB2E3270
MS35-20SPSX1
MS35-20SPSX1
WALI06LXXXX0
MS30-06PSNX2
PKFU125V10A0
PPNSBB2E7080
Wiring Setup
1 x Mounting Template
- Speaker
1 x Quickstart Guide and
Reference Manual
1 x Quickstart Guide
1 x Radio Installation Sheet
1 x Warranty Sheet
1 x DSC Sticker
1 x Dust Cap for Handset
connector plate
OPTIONAL ADDITIONAL
HANDSET KIT
16/9
3CH
CALL
SCAN
WX
FUNC
(NS100HS)
1 x Hand set with cord (US)
PPNSBB2E7030
PPNSBB2E7050
PPNSBB2E7070
PPNSBB2E7260
PPNSBB2E7100
PPNSBB2E7110
MPLILTD-4/80
PART CODE
APNSBB2E8030
Black Box
Radio
Power/NMEA
HLR
Station 1
Station 2
HLR
16/9
3CH
CALL
SCAN
WX
FUNC
Ground lug
Antenna
10A F us e
COLOR FUNCTION PIN#
10A
RED BATTERY (+) 5
BLACK G ROUND 1
GREEN NMEA IN (+) 2
YELLOW NMEA IN (–) 6
ORANGE NMEA OUT (+) 3
BLACK NMvE A OUT (–) 4
Power Cable
Hailer Cable
COLOR FUNCTION PIN#
YELLOW HAILER (+) 1
BLACK H AILER (–) 8
Female-Female adapter
1 x Mic Plate - black
1 x Black Box to Speaker
cord with Female-Female
Adapter
3 x SS self tapping screws
1 x Mic Clip with magnet
2 x SS self tapping screws
MMNSBB2E4000
WALI 08L07KX0
WALI 08F 08F0
MS35-20SPSX1
APNSBB2E8050
MS35-20SPSX1
10 pin s oc ket
8 pin socket
Hand set
connector plate
Dust cap
Hand set &
mike clip
16/9
3CH
CALL
SCAN
WX
FUNC
for mic clip
1 x Large Speaker
1 x Speaker Gasket
4 x Speaker tabs
4 x SS self tapping screws
1 x Installation Sheet
1 x Dust Cap for Handset
connector plate
APNSBB2E8060
MPNSBB2E7040
PPNSBB2E3270
MS35-20TSPX1
PPNSBB2E7030
MPLILTD-4/80
Tools Required
• Drill
• Sabre saw
Large speaker
•1-1/4” Hole
Saw
•1” Hole Saw
1/8” Drill bit
Pencil
Phillips
Screwdriver
Installation Tips Installing Handset Connector Installing Microphone Clip Plate
Speaker is at least
45cms (1.5') from
the compass
Black Box Radio must
be at least 1metre (3’)
from the Antenna
Find a location for the Handset connector near
1.
the vessel steering wheel and check that there is
enough wire length to reach the remote speaker
location. Stretch the mike cord to be sure the
handset is comfortable to use while driving.
Using the black metal plate as a guide, mark the
2.
center of the hole to be drilled.
Use a 1” hole saw to cut out the dash.
3.
Leaving the small rubber gasket on the backside
4.
of the connector, push it through the D hole
in the plate. Put the rubber dust cap over the
connector shaft and tighten the nylon nut.
Hold the plate & connector assembly to the dash
5.
and mark the 3 holes. Use a 1/8” drill. Mount the
plate with the 3 screws provided.
Connect the handset connector.
6.
When removed, be sure to cover the connector
7.
with the provided dust cap.
Mount the handset near the mounted
1.
connector allowing a drip loop in the MIKE
cord. Be sure there is about 2” of vertical
clearance to allow the handset to be easily
lifted off and returned to the clip plate.
Place the clip plate on the dash with the
2.
magnetic sensor toward the rear. Using the clip
plate as a guide, mark the 2 holes.
Use a 1/8” drill. Mount the clip plate with the 2
3.
screws provided.
Mount the handset connector.
4.
Location Requirements - Please check these before doing
any cutting or drilling.
Ensure that the chosen location:
• is at least one metre (3') from the antenna
• allows easy connection to (at least) a 10 Amp fused 12V
only DC electrical source and the antenna.
• is at least 45cms (1.5') from the compass to avoid
creating magnetic deviation of the compass during radio
operation
• has a suitable space close by for installing the
microphone bulkhead mount
• provides easy access to the front panel controls
• provides reasonable access to the wiring at the back of
the radio.
1.
Check that the location of the powerful 20W
4 Ohm HAILER HORN (not provided) does not
effect the ship’s compass before drilling holes
and mounting. The Horn needs a clear view of
the bow of the boat so the FOG and PA signals
can be heard well by other vessels.
2.
Run 2 #20 AWG wires from the horn to the Box
and connect to the HAILER connector wires.
Follow the wire colors on the front of this sheet
and crimp to the HAILER connector assembly
wiring.
NOTE: DO NOT GROUND EITHER SIDE OF THE
CAUTION
HAILER WIRES.
Installing Remote SpeakerWiring Hailer Connector
Check the location does not effect the ship’s
1.
compass before drilling any holes.
Using the template provided, use the 1-1/4”
2.
hole saw to cut out the 4 corners.
Use the sabre saw to trim the remaining inside
3.
of the speaker cutout.
Use the 1/8” drill bit for the 4 side mounting
4.
holes.
Mount the speaker with supplied gasket from
5.
the front and hook up the connectors.. No
need to get behind the panel.
Put the 4 speaker clips on the speaker to cover
6.
up the mounting holes for a professional look.
PPNSBB2E7080 (L A 00 040 6A)
Loading...