Page 1
www.nordictrack.com
Model No. 831.14895.1
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal
(on the frame behind the backrest)
QUESTIONS?
USERʼS MANUAL
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-825-2588
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.nordictrackservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
Page 2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
I
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
ROTATING ON THE INVERSION TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
DEVELOPING A PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s)
of the warning decal(s). If a decal is
missing or illegible, see the front
cover of this manual and request
a free replacement decal. Apply
the decal in the location shown.
Note: The decal(s) may not be
shown at actual size.
NordicTrack is a registered trademark of ICON IP, Inc.
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your inversion table before using your inversion
table. ICON assumes no responsibility for personal injury or property damage sustained by or
hrough the use of this product.
t
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the inversion table are adequately informed of all precautions.
3. Your inversion table is intended for home
use only. Do not use your inversion table in
a commercial, rental, or institutional setting.
4. Keep the inversion table indoors, away from
moisture and dust. Do not put the inversion
table in a garage or covered patio or near
water.
5. Use the inversion table only on a level surface. Cover the floor beneath the inversion
table to protect the floor.
6. Make sure that all parts are properly tightened each time the inversion table is used.
Replace any worn parts immediately.
7. Keep children under age 12 and pets away
from the inversion table at all times.
11. Wear athletic shoes with laces to help
secure your feet in the inversion table and
for foot protection while using the inversion
table.
12. Always engage the pins on the backrest
frame into the same holes in both pivot bars.
13. Make sure that the pivot bars are held in the
brackets on the backrest frame before you
use the inversion table.
14. Keep hands and feet away from moving
parts.
15. Make sure that the ankle lock is secured
snugly against your ankles and that the
short knob is fully tightened before you use
the inversion table.
16. Make sure that the linking bars are in
straight positions before you use the inversion table.
17. Do not use the handlebars to rotate upward
on the inversion table; the handlebars are
for mounting and dismounting the inversion
table.
8. The inversion table is designed to support a
maximum user weight of 300 lbs. (136 kg).
9. Do not use weights with the inversion table.
10. The inversion table should be used only by
persons 6 ft. 6 in. (198 cm) tall or less.
18. Perform all activities on the inversion table
in a slow, controlled manner. Aggressive
movement can cause the inversion table to
tip over.
19. Use the inversion table with a partner.
partner should be ready to return the
backrest to the upright position if you cannot complete a rotation.
3
Your
Page 4
20. If you feel pain or dizziness while using the
nversion table, stop immediately.
i
21. The following factors and conditions may
make inverting inadvisable (this list is not
exhaustive; it is intended only for reference).
If one or more factors or conditions apply to
ou, consult your physician before using the
y
inversion table.
• Pregnancy
• Hiatal hernia or ventral hernia
• Glaucoma, retinal detachment, or conjunctivitis
• High blood pressure, hypertension, or
recent stroke or transient ischemic attack
• Heart or circulatory disorders for which
ou are being treated
y
• Middle ear infection and extreme obesity
• Spinal injury, cerebral sclerosis, or acutely
swollen joints
• Bone weakness (osteoporosis), recent
unhealed fractures, medullary pins, or sur-
ically implanted orthopedic supports
g
• The use of anticoagulants, including high
doses of aspirin
22. Use your inversion table only as described
in this manual.
4
Page 5
BEFORE YOU BEGIN
Thank you for selecting the NordicTrack®REVITALIZE™ INVERSION SYSTEM 2.0 inversion table. The
inversion table will increase your intervertebral dimen-
ion, decrease pressure on intervertebral discs,
s
stretch and relax your muscles, and temporarily
elieve back pain associated with the listed conditions.
r
For your benefit, read this manual carefully before
using the inversion table. If you have questions after
ASSEMBLED DIMENSIONS:
Height: 5 ft. 2 in. (157 cm)
Width: 3 ft. (91 cm)
Depth: 6 ft. 6 in. (168 cm)
Handle
Right Frame
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
odel number and the location of the serial number
m
decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Headrest
Backrest
Short Adjustment Knob
Short Adjustment Knob
Long Adjustment Knob
Lock Frame
Foot Frame
Index Handle
Left Frame
5
Page 6
M10 Locknut (65)
M8 Locknut (57)
M6 Washer (62)
M4 x 15mm
Screw (58)
M10 x 85mm Button Bolt (51)
M10 x 95mm Button Bolt (53)
M6 x 18mm
Button Screw (55)
M6 x 60mm Button Screw (56)
M4 x 30mm
Screw (63)
M4 x 20mm
Screw (59)
M10 Curved Washer (50)
M6 Nut (43)
M10 x 40mm Button Bolt (69)
M10 x 16mm
Button Screw (54)
M10 x 80mm Button Bolt (52)
M10 x 53mm Button Bolt (49)
M8 x 16mm
Button Bolt (61)
M10 Large Washer (64)
M6 x 37mm Bolt (33)
PART IDENTIFICATION CHART
ee the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
S
the key number of the part, from the PART LIST near the end of this manual. Note: If a part is not in the hard-
ware kit, check to see if it has been preassembled.
6
Page 7
ASSEMBLY
o make assembly easier, carefully read the fol-
T
lowing information and instructions:
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 6.
1.
Before beginning assembly, make sure
that you understand the information in
the box above.
Press a 63mm Round Cap (40) onto the Left
Base (1).
The following tools (not included) may be required
•
for assembly:
two adjustable wrenches
one rubber mallet
one standard screwdriver
one Phillips screwdriver
Assembly may be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1
2
1
Next, tighten a Leveling Foot (41) into the Left
Base (1).
Attach a Foot (42) to the Left Base (1) with an
M4 x 20mm Screw (59).
Repeat this step for the Right Base (2).
2. Attach the Left Base (1) to the Right Base (2)
with two M10 x 80mm Button Bolts (52), four
M10 Curved Washers (50), and two M10
Locknuts (65). Do not tighten the Locknuts
yet.
Attach another Foot (42) to the Right Base (2)
with an M4 x 20mm Screw (59).
42
59
40
41
2
2
42
59
52
50
50
65
1
7
Page 8
3. Attach the Support Bracket (15) to the Center
Base (3) with two M4 x 15mm Screws (58).
3
15
58
58
3
4. Attach the Center Base (3) to the Left and
Right Bases (1, 2) with four M10 x 80mm
Button Bolts (52), four M10 Curved Washers
(50), and four M10 Locknuts (65). Do not
tighten the Locknuts yet.
5. See the inset drawing. Identify the Center
Frame (7).
Apply some of the included grease to both
sides of the Left Large Spacer (31).
4
52
50
5
60
65
50
2
1
3
50
52
50
52
65
32
65
64
48
Attach the Left Large Spacer (31) and the Left
Frame (4) to the Center Frame (7) with an
M10 Locknut (65), an M10 Large Washer
(64), and a 29mm Spacer (48).
Then, press an 89mm Cap (32) into the
Center Frame (7).
Repeat this step with the Right Large
Spacer (60) and the Right Frame (5).
5
7
Grease
7
31
4
8
Page 9
6. Attach the Left and Right Frames (4, 5) to the
Left and Right Bases (1, 2) with four M10 x
85mm Button Bolts (51) and four M10
ocknuts (65).
L
ee steps 2 and 4. Tighten the M10
S
Locknuts (65).
6
5
65
7. Attach the Top Cover (23) and the Bottom
Cover (24) to the Center Frame (7) with two
M4 x 15mm Screws (58) and an M4 x 30mm
Screw (63).
Attach the Center Frame Extension (6) to the
Center Frame (7) with two M10 x 53mm
Button Bolts (49) and two M10 Locknuts (65).
65
51
7
7
49
58
2
65
23
4
65
1
51
24
63
58
6
65
9
Page 10
8. Orient the Headrest Frame (9) and the
ackrest Frame (8) as shown.
B
Attach the Headrest Frame (9) to the
Backrest Frame (8) with two M10 x 16mm
Button Screws (54).
8
9
54
54
8
9. Grease an M10 x 95mm Button Bolt (53).
Pull the indicated Short Adjustment Knob (37)
outward as far as possible.
Insert the bracket on the Backrest Frame (8)
into the Top Cover (23).
Next, attach the Backrest Frame (8) to the
Center Frame Extension (6) with the M10 x
95mm Button Bolt (53) and an M10 Locknut
(65).
Then, engage the Short Adjustment Knob (37)
into one of the holes in the bracket.
See the inset drawing. Attach an M8 x
16mm Button Bolt (61) and an M8 Locknut
(57) to the hole in the end of the bracket on
the Backrest Frame (8).
10. Attach the Foot Frame (19) to the Leg Frame
(10) with two M10 x 40mm Button Bolts (69)
and two M10 Locknuts (65).
9
10
65
8
Grease
19
Bracket
6
53
23
37
69
57
8
61
65
10
10
Page 11
11. Slide two Foam Pads (22) onto the Lock
Frame (11).
hen, press two Pad Caps (45) into the Foam
T
Pads (22).
Next, pull the indicated Long Adjustment
Knob (13) outward, insert the Lock Frame
(11) into the Leg Frame (10), and then
release the Long Adjustment Knob.
Make sure that the Long Adjustment Knob
(13) is engaged in the indicated adjustment hole in the Lock Frame (11).
11
45
11
22
17
Hole
45
22
13
43
10
Insert an M6 x 37mm Bolt (33) into the Leg
Frame (10) and into the loop on the end of
the Spring (17). Tighten an M6 Nut (43) onto
the Bolt.
12. Insert the Pad Tube (18) into the welded tube
on the Leg Frame (10).
Next, tighten an M4 x 15mm Screw (58) into
each side of the Pad Tube (18).
Slide two Foam Pads (22) onto the Pad Tube
(18).
Then, press two Pad Caps (45) into the Foam
Pads (22).
13. Pull the indicated Short Adjustment Knob (37)
outward as far as possible, and insert the end
of the Leg Frame (10) a few inches into the
Backrest Frame (8).
See the inset drawing. Press the indicated
tab on the Leg Frame Bushing (38), and
press the Leg Frame Bushing upward into the
Backrest Frame (8). Make sure that the tab
is in the indicated hole in the Backrest
Frame.
12
13
45
10
Tab
22
Hole
38
33
45
22
58
18
8
10
8
10
37
Holes
Then, slide the Leg Frame (10) farther into
the Backrest Frame (8), and engage the Short
Adjustment Knob (37) into one of the holes in
the Leg Frame.
11
Page 12
14. Attach the Headrest (20) to the Headrest
Frame (9) with two M6 x 18mm Button
Screws (55), an M6 x 60mm Button Screw
56), and three M6 Washers (62).
(
14
20
9
62
ttach the Backrest (21) to the Backrest
A
Frame (8) in the same way.
15. Attach a Handle (12) to the Left Frame (4)
with two M10 x 80mm Button Bolts (52), two
M10 Curved Washers (50), and two M10
Locknuts (65).
Attach the other Handle (12) in the same
way.
Make sure that all parts are properly tightened before you use the inversion table.
15
56
55
21
8
12
62
12
65
WARNING:
HOW TO LOCK THE INVERSION TABLE
FOR STORE DISPLAY OR TO PREVENT
UNSUPERVISED USE
When the inversion table is displayed in a
store, or when it is not in use, it should be
locked to prevent unsupervised use. First,
insert the threaded end of the Lock Pin
(35) into the Center Base (3), and position
the other end of the Lock Pin on top of the
Leg Frame (10). Then, tighten an M10
Locknut (65) onto the Lock Pin.
65
4
50
52
65
10
35
3
12
Page 13
ADJUSTMENT
his section explains how to adjust the inversion table. See DEVELOPING A PROGRAM on page 17 for impor-
T
tant information about how to get the most benefit from the inversion table.
Make sure that all parts are properly tightened each time you use the inversion table. Replace any worn parts
mmediately. The inversion table can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not
i
use solvents to clean the inversion table.
SELECTING THE BACKREST FRAME POSITION
See the inset drawing. The bracket on the
Backrest Frame (8) has four adjustment holes. The
correct hole to use will depend on your body weight
and the desired level of responsiveness. See the
chart to determine which hole to use. For example,
if you weigh between 200 and 250 pounds and you
are a beginning user, the chart recommends that
you use hole A.
To adjust the Backrest Frame (8), first pull the Short
Adjustment Knob (37) out as far as it will go. Move
the Backrest Frame and engage the Short
Adjustment Knob into the desired hole in the bracket on the Backrest Frame.
Try the inversion table with the Backrest Frame (8)
adjusted to each position to determine which one is
best for you.
8
Note: 1 lb. = 2.2 kg
Hole A
Hole B
Hole C
Hole D
8
37
13
Page 14
ADJUSTING THE LEG FRAME
The length of the Leg Frame (10) can be adjusted
o correspond to your height. Pull the Short
t
Adjustment Knob (37) outward as far as possible.
Slide the Leg Frame (10) into or out of the Backrest
Frame (8) so that the first or second measurement
greater than your height is covered by the Backrest
Frame.
Then, engage the Short Adjustment Knob (37) into
the adjustment holes in the Leg Frame and the
Backrest Frame.
Use the inversion table with the Leg Frame (10)
adjusted to a few different lengths to determine
which length is best for you.
WARNING: The inversion table
is designed to be used by persons 6 ft. 6 in.
(198 cm) tall or less.
eight
H
Measurements
10
8
37
Adjustment
Hole
ADJUSTING THE LOCK FRAME
To secure your ankles in the inversion table, first
pull the Long Adjustment Knob (13) outward as far
as possible.
See the inset drawing. Next, pull the Lock Frame
(11) away from the Leg Frame (10). Stand on the
Foot Frame (19) with the backs of your legs against
the indicated Foam Pads (22) and your toes under
the Lock Frame.
Then, push the Lock Frame (11) against your
ankles and engage the Long Adjustment Knob (13)
into one of the adjustment holes in the Lock Frame.
Make sure that the Long Adjustment Knob is
engaged in one of the adjustment holes in the
Lock Frame.
WARNING: Make sure that the
Lock Frame (11) is secured snugly against
your ankles before you use the inversion
system. Always wear athletic shoes with
laces to help secure your feet in the inversion system.
19
19
22
11
13
10
13
22
10
14
Page 15
SETTING THE INVERSION ANGLE
The inversion table can be set to rotate between 15
egrees and 90 degrees, in 15 degree increments.
d
o set the inversion angle, pull the Index Handle
T
(25) outward as far as possible, and then turn the
Index Handle until the arrow on top of the Index
Handle points to the desired degree setting. Then,
release the Index Handle; make sure that the
Index Handle is fully engaged.
LEVELING THE INVERSION TABLE
Arrow
25
If the inversion table rocks slightly on your floor,
turn one or both of the Leveling Feet (41) until the
inversion table is level.
LOCKING THE INVERSION TABLE
To lock the inversion table when you are not using
it, insert the threaded end of the Lock Pin (35) into
the Center Base (3), and position the other end of
the Lock Pin on top of the Leg Frame (10). Then,
tighten an M10 Locknut (65) onto the Lock Pin.
65
10
35
3
41
41
15
Page 16
ROTATING ON THE INVERSION TABLE
This section explains how to rotate back on the inversion table, and then return to the starting position. Before
using the inversion table, see the ADJUSTMENT section starting on page 13 to correctly set up the
inversion table. Always exercise with a partner.
he upright position if you cannot complete the rotation.
t
Your partner should be ready to return the backrest to
OTATING BACK ON THE INVERSION TABLE
R
To rotate back on the inversion table, slowly lift your
arms over your head until you reach the desired position. The speed at which you lift your arms will determine how quickly the inversion table will rotate. Rest
your arms in a comfortable position that does not
cause the inversion table to rotate. Note: The inversion table will rotate only to the degree setting set by
the index handle.
OTATING UP ON THE INVERSION TABLE
R
To return to the starting position, move your hands
toward your waist until you rotate to a horizontal position. Rest in a horizontal position for 30 to 60 seconds
before rotating to the starting position. This will allow
your body to readjust. Return to the starting position
slowly. Dizziness after using the inversion table is an
indication that you have returned to the starting position too quickly.
To rotate up from the fully inverted position, pull yourself up using the handles.
Do not sit up to return to the starting position.
16
Page 17
DEVELOPING A PROGRAM
This section contains information and suggestions about using the inversion table. Make sure that all parts are
roperly tightened each time the inversion table is used. Replace any worn parts immediately. See the ADJUST-
p
MENT section starting on page 13 to identify parts referred to in this section.
BENEFITING FROM USING THE INVERSION TABLE
If you feel nauseated while using the inversion table,
return to the starting position. Note that it may take a
few weeks of use for your inner ear to become accustom to being inverted.
Do not use the inversion table right after you have
eaten.
Moving while using the inversion table may make it a
more comfortable experience, and may help joints and
muscles stretch and relax. Always move in a slow,
controlled manner.
The greater the angle at which the inversion table is
used, the shorter the time that you should rotate back
before rotating up. Increase the amount of inverted
time and the angle of use gradually.
Always pay attention to how your body feels as you
use the inversion table. Increase the level of intensity
only as it is comfortable for you. When you feel like
you have had enough, return to the starting position.
BEGINNER PROGRAM
The following are suggestions for persons who are just
starting to use the inversion table.
INTERMEDIATE PROGRAM
The following are suggestions for persons who have
become comfortable using the inversion table as
described under the BEGINNER PROGRAM.
Increase the angle to which the inversion table can
rotate, as it is comfortable. Adjust the index handle to
allow the inversion table to rotate to up to 60 degrees,
a few degrees at a time.
Start to do gentle stretching while using the inversion
table.
Gradually increase the amount of time that you use
the inversion table to ten minutes or more, two or
three times a day. Routines can be varied from rotating back for one or two minutes and then up for 30
seconds, to rotating back and up for equal amounts of
time.
FULL INVERSION PROGRAM
The following are suggestions for persons who have
become comfortable using the inversion table as
described under the INTERMEDIATE PROGRAM and
desire to rotate to greater angles. Note that all the
benefits of inversion can be gained by rotating to 60
degrees. Do not attempt to do sit-ups.
Set the index handle to allow the backrest frame to
rotate to 15 degrees or less for the first one or two
weeks. This will allow your body time to adjust to the
change in gravitational pull.
Use the inversion table for one or two minutes at a
time, two or three times a day.
Stay inverted only for as long as it is comfortable. This
may be only a few seconds at first.
Increase the angle to which the inversion table can
rotate, as it is comfortable. Adjust the index handle to
allow the inversion table to rotate until it comes in contact with the center frame.
Adjust the backrest frame so that the long adjustment
knob is in the top hole (see SELECTING THE BACKREST FRAME POSITION on page 13). If you weigh
220 lbs. (100 kg) or more, adjust the long adjustment
knob to the center hole in the backrest frame. Rotate
back and up as described on page 16.
17
Page 18
PART LIST—Model No. 831.14895.1 R0609A
Key No. Qty. Description Key No. Qty. Description
11Left Base
21Right Base
31Center Base
41Left Frame
51Right Frame
61Center Frame Extension
71Center Frame
81Backrest Frame
91Headrest Frame
10 1 Leg Frame
11 1 Lock Frame
12 2 Handle
13 1 Long Adjustment Knob
14 2 30mm x 70mm Inner Cap
15 1 Support Bracket
16 1 25mm Square Inner Cap
17 1 Spring
18 1 Pad Tube
19 1 Foot Frame
20 1 Headrest
21 1 Backrest
22 4 Foam Pad
23 1 Top Cover
24 1 Bottom Cover
25 1 Index Handle
26 1 Index Ring
27 1 Cup Washer
28 1 Small Spring
29 1 Cup Bushing
30 1 Index Cup
31 1 Left Large Spacer
32 3 89mm Cap
33 1 M6 x 37mm Bolt
34 1 M6 x 33mm Bolt
35 1 Lock Pin
36 1 Bumper
37 2 Short Adjustment Knob
38 1 Leg Frame Bushing
39 2 42mm x 70mm Cap
40 2 63mm Round Cap
41 2 Leveling Foot
42 3 Foot
43 3 M6 Nut
44 2 32mm Round Cap
45 4 Pad Cap
46 1 M6 x 60mm Button Bolt
47 2 Pivot Bushing
48 2 29mm Spacer
49 2 M10 x 53mm Button Bolt
50 12 M10 Curved Washer
51 4 M10 x 85mm Button Bolt
52 10 M10 x 80mm Button Bolt
53 1 M10 x 95mm Button Bolt
54 2 M10 x 16mm Button Screw
55 4 M6 x 18mm Button Screw
56 2 M6 x 60mm Button Screw
57 1 M8 Locknut
58 8 M4 x 15mm Screw
59 3 M4 x 20mm Screw
60 1 Right Large Spacer
61 1 M8 x 16mm Button Bolt
62 7 M6 Washer
63 1 M4 x 30mm Screw
64 2 M10 Large Washer
65 22 M10 Locknut
66 1 M6 x 15mm Screw
67 2 M5 x 15mm Screw
68 1 30mm x 60mm Cap
69 2 M10 x 40mm Button Bolt
*–Userʼs Manual
*–Assembly Tool
*–Grease Packet
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
18
Page 19
EXPLODED DRAWING—Model No. 831.14895.1 R0609A
1
2
4
5
6
7
8
9
12
12
20
21
23
24
25
26
27
28
29
30
31
32
32
60
32
39
38
40
40
41
41
42
42
42
37
37
44
44
47
48
48
47
39
36
65
65
52
52
65
52
52
52
53
55
56
55
5
6
54
58
46
58
49
59
59
61
50
50
50
58
50
50
50
6
2
62
65
51
65
65
65
65
65
57
65
65
65
54
51
65
65
67
67
66
64
64
43
63
62
62
62
6
8
58
10
33
58
59
15
65
65
58
35
65
65
69
43
13
43
34
16
17
45
45
22
22
22
45
18
22
45
19
14
14
3
11
58
19
Page 20
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
fees for service needed under warranty. Go to www.nordictrackservice.com/registration.
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. Parts and labor are warranted for ninety (90) days from
the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All
repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to
a service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge. This
warranty does not extend to any damage to a product caused by or attributable to freight damage, abuse,
misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service center; to
products used for commercial or rental purposes or as store display models; or to products transported
or purchased outside the US. No other warranty beyond that specifically set forth above is authorized by
ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in connection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 281996 R0609A Printed in China © 2009 ICON IP, Inc.
Loading...