Nokia XS250WXAB Users manual
7368 ISAM ONT XS-240W-A XS-250WX-A Product Guide
7368 Intelligent Services Access
Manager ONT
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
3FE-48631-AAAA-TCZZA
Issue: 01
Nokia — Proprietary and confidential
Use pursuant to applicable agreements
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Nokia is a registered trademark of Nokia Corporation. Other products and company
names mentioned herein may be trademarks or tradenames of their respective
owners.
The information presented is subject to change without notice. No responsibility is
assumed for inaccuracies contained herein.
© 2018 Nokia.
Contains proprietary/trade secret information which is the property of Nokia and must
not be made available to, or copied or used by anyone outside Nokia without its
written authorization. Not to be used or disclosed except in accordance with
applicable agreements.
2
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
1Preface
This preface provides general information about the documentation set for optical
network terminals (ONTs).
1.1 Scope
This documentation set provides information about safety, features and functionality,
ordering, hardware installation and maintenance, and software installation
procedures for the current release.
1.2 Audience
This documentation set is intended for planners, administrators, operators, and
maintenance personnel involved in installing, upgrading, or maintaining the ONTs.
Preface
1.3 Required knowledge
The reader must be familiar with general telecommunications principles.
1.4 Acronyms and initialisms
The expansions and optional descriptions of most acronyms and initialisms appear
in the glossary.
1.5 Assistance and ordering phone numbers
Nokia provides global technical support through regional call centers. Phone
numbers for the regional call centers are available at the following URL:
http://support.alcatel-lucent.com
For ordering information, contact your Nokia sales representative.
.
Issue: 01 3FE-48631-AAAA-TCZZA 3
Preface
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
1.6 Nokia quality processes
Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These
requirements are documented in the Fixed Networks Quality Manual
3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical
requirements and customer end-point requirements are met. The customer or its
representatives may be allowed to perform on-site quality surveillance audits, as
agreed upon during contract negotiations
1.7 Safety information
For safety information, see the appropriate safety guidelines chapter.
1.8 Documents
Documents are available using ALED or OLCS.
Procedure 1 To download a ZIP file package of the customer documentation
1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you
are a new user and require access to this service, please contact your Nokia sales
representative.
2 From the Technical Content for drop-down menu, choose the product.
3 Click on Downloads: Electronic Delivery.
4 Choose Documentation from the drop-down menu and click Next.
5 Select the image from the drop-down menu and click Next.
6 Follow the on-screen directions to download the file.
4
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Procedure 2 To access individual documents
Individual PDFs of customer documents are also accessible through the Nokia Customer Support
website.
1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you
are a new user and require access to this service, please contact your Nokia sales
representative.
2 From the Technical Content for drop-down menu, choose the product.
3 Click on Manuals and Guides to display a list of customer documents by title and part
number. You can filter this list using the Release drop-down menu.
4 Click on the PDF to open or save the file.
Preface
1.9 Special information
The following are examples of how special information is presented in this document.
Danger — Danger indicates that the described activity or
situation may result in serious personal injury or death; for
example, high voltage or electric shock hazards.
Warning — Warning indicates that the described activity or
situation may, or will, cause equipment damage or serious
performance problems.
Caution — Caution indicates that the described activity or
situation may, or will, cause service interruption.
Note — A note provides information that is, or may be, of
special interest.
Issue: 01 3FE-48631-AAAA-TCZZA 5
Preface
1.9.1 Procedures with options or substeps
When there are options in a procedure, they are identified by letters. When there are
required substeps in a procedure, they are identified by roman numerals.
Procedure 3 Example of options in a procedure
At step 1, you can choose option a or b. At step 2, you must do what the step indicates.
1 This step offers two options. You must choose one of the following:
a This is one option.
b This is another option.
2 You must perform this step.
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Procedure 4 Example of required substeps in a procedure
At step 1, you must perform a series of substeps within a step. At step 2, you must do what the
step indicates.
1 This step has a series of substeps that you must perform to complete the step. You must
perform the following substeps:
i This is the first substep.
ii This is the second substep.
iii This is the third substep.
2 You must perform this step.
6
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
1.10 Multiple PDF document search
You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a
common term. Adobe Reader displays the results in a single display panel. The
results are grouped by PDF file, and you can expand the entry for each file.
Note — The PDF files in which you search must be in the same
folder.
Procedure 5 To search multiple PDF files for a common term
1 Open Adobe Acrobat Reader.
2 Choose Edit→Search from the Acrobat Reader main menu. The Search PDF panel appears.
Preface
3 Enter the search criteria.
4 Click on the All PDF Documents In radio button.
5 Select the folder in which to search using the drop-down menu.
6 Click on the Search button.
Acrobat Reader displays the search results. You can expand the entries for each document
by clicking on the + symbol.
Issue: 01 3FE-48631-AAAA-TCZZA 7
Preface
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
8
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Table of contents
1 Preface.............................................................................................3
1.1 Scope ..........................................................................................................3
1.2 Audience......................................................................................................3
1.3 Required knowledge....................................................................................3
1.4 Acronyms and initialisms .............................................................................3
1.5 Assistance and ordering phone numbers ....................................................3
1.6 Nokia quality processes...............................................................................4
1.7 Safety information........................................................................................ 4
1.8 Documents ..................................................................................................4
1.9 Special information ......................................................................................5
1.9.1 Procedures with options or substeps...........................................................6
1.10 Multiple PDF document search ...................................................................7
2 ETSI ONT safety guidelines .........................................................17
2.1 Safety instructions .....................................................................................17
2.1.1 Safety instruction boxes ............................................................................17
2.1.2 Safety-related labels..................................................................................18
2.2 Safety standards compliance ....................................................................19
2.2.1 EMC, EMI, and ESD compliance...............................................................19
2.2.2 Equipment safety standard compliance.....................................................19
2.2.3 Environmental standard compliance .........................................................20
2.2.4 Laser product standard compliance ..........................................................20
2.2.5 Resistibility requirements compliance .......................................................20
2.2.6 Acoustic noise emission standard compliance..........................................20
2.3 Electrical safety guidelines ........................................................................20
2.3.1 Power supplies ..........................................................................................21
2.3.2 Cabling ......................................................................................................21
2.3.3 Protective earth .........................................................................................21
2.4 ESD safety guidelines ...............................................................................21
2.5 Laser safety guidelines..............................................................................21
2.5.1 Laser classification .................................................................................... 22
2.5.1.1 Laser warning labels..................................................................................22
2.5.2 Transmit optical output ..............................................................................24
2.5.3 Normal laser operation ..............................................................................24
2.5.4 Location class............................................................................................25
2.6 Environmental requirements......................................................................25
3 ETSI environmental and CRoHS guidelines...............................27
3.1 Environmental labels .................................................................................27
3.1.1 Overview....................................................................................................27
3.1.2 Environmental related labels .....................................................................27
3.1.2.1 Products below Maximum Concentration Value (MCV) label....................27
3.1.2.2 Products containing hazardous substances above Maximum
Concentration Value (MCV) label ..............................................................28
3.2 Hazardous Substances Table (HST).........................................................29
3.3 Other environmental requirements ............................................................29
Issue: 01 3FE-48631-AAAA-TCZZA 9
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
3.3.1 ONT environmental requirements .............................................................29
3.3.2 Storage ......................................................................................................29
3.3.3 Transportation ...........................................................................................30
3.3.4 Stationary use............................................................................................30
3.3.5 Thermal limitations ....................................................................................30
3.3.6 Material content compliance......................................................................30
3.3.7 End-of-life collection and treatment ...........................................................31
4 ANSI ONT safety guidelines ........................................................33
4.1 Safety instructions .....................................................................................33
4.1.1 Safety instruction boxes in customer documentation ................................ 33
4.1.2 Safety-related labels..................................................................................34
4.2 Safety standards compliance ....................................................................35
4.2.1 EMC, EMI, and ESD standards compliance..............................................36
4.2.2 Equipment safety standard compliance.....................................................36
4.2.3 Environmental standards compliance........................................................37
4.2.4 Laser product standards compliance.........................................................37
4.2.5 Resistibility requirements compliance .......................................................38
4.3 Laser safety guidelines..............................................................................38
4.3.1 Laser warning labels..................................................................................38
4.3.2 Laser classification .................................................................................... 40
4.3.3 Transmit optical output ..............................................................................41
4.3.4 Normal laser operation ..............................................................................41
4.3.5 Location class............................................................................................41
4.4 Electrical safety guidelines ........................................................................42
4.4.1 Power supplies ..........................................................................................42
4.4.2 Cabling ......................................................................................................42
4.4.3 Protective earth .........................................................................................42
4.5 ESD safety guidelines ...............................................................................42
4.6 Environmental requirements......................................................................43
10
5 XS-240W-A and XS-250WX-A unit data sheet ............................45
5.1 XS-240W-A and XS-250WX-A part numbers and identification ................45
5.2 XS-240W-A and XS-250WX-A general description...................................48
5.2.1 TR69 authentication using TLS and CA certificates ..................................51
5.3 XS-240W-A and XS-250WX-A software and installation feature
support.......................................................................................................52
5.4 XS-240W-A and XS-250WX-A interfaces and interface capacity..............52
5.4.1 XS-240W-A and XS-250WX-A connections and components ..................53
5.5 XS-240W-A and XS-250WX-A LEDs ........................................................53
5.6 XS-240W-A and XS-250WX-A detailed specifications ..............................55
5.7 XS-240W-A and XS-250WX-A GEM ports and T-CONTs.........................56
5.8 XS-240W-A and XS-250WX-A functional blocks.......................................57
5.9 XS-240W-A and XS-250WX-A standards compliance ..............................61
5.9.1 Responsible party......................................................................................61
5.9.2 Energy-related products standby and off modes compliance....................62
5.9.3 FCC statement ..........................................................................................62
5.9.4 FCC Radiation Exposure Statement .........................................................63
5.10 XS-240W-A and XS-250WX-A special considerations..............................63
5.10.1 Wi-Fi service..............................................................................................63
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
5.10.1.1 Wi-Fi physical features .............................................................................. 63
5.10.1.2 Wi-Fi standards and certifications .............................................................64
5.10.1.3 Wi-Fi GUI features.....................................................................................64
5.10.2 XS-240W-A and XS-250WX-A ONT considerations and limitations .........64
6 Install an XS-240W-A or XS-250WX-A indoor ONT ....................65
6.1 Purpose .....................................................................................................65
6.2 General......................................................................................................65
6.3 Prerequisites..............................................................................................65
6.4 Recommended tools..................................................................................65
6.5 Safety information......................................................................................66
6.6 Procedure ..................................................................................................67
7 Replace an XS-240W-A or XS-250WX-A indoor ONT.................73
7.1 Purpose .....................................................................................................73
7.2 General......................................................................................................73
7.3 Prerequisites..............................................................................................73
7.4 Recommended tools..................................................................................73
7.5 Safety information......................................................................................74
7.6 Procedure ..................................................................................................75
8 Configure an XS-240W-A or XS-250WX-A indoor ONT .............79
8.1 General......................................................................................................79
8.2 HGU mode GUI configuration....................................................................79
8.2.1 Login..........................................................................................................79
8.2.2 Device and connection status....................................................................80
8.2.3 Network configuration................................................................................94
8.2.4 Security configuration ..............................................................................113
8.2.5 Application configuration .........................................................................122
8.2.6 Maintenance ............................................................................................130
8.2.7 RG troubleshooting counters...................................................................142
Issue: 01 3FE-48631-AAAA-TCZZA 11
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
12
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
List of figures
2 ETSI ONT safety guidelines .........................................................17
Figure 1 PSE certification........................................................................................19
Figure 2 Laser product label....................................................................................22
Figure 3 Laser classification label............................................................................23
Figure 4 Laser warning labels..................................................................................24
3 ETSI environmental and CRoHS guidelines...............................27
Figure 5 Products below MCV value label...............................................................28
Figure 6 Products above MCV value label ..............................................................28
Figure 7 Recycling/take back/disposal of product symbol....................................... 31
4 ANSI ONT safety guidelines ........................................................33
Figure 8 Sample safety label on the ONT equipment..............................................35
Figure 9 Sample laser product label showing CDRH 21 CFR compliance..............37
Figure 10 Laser product label ....................................................................................39
Figure 11 Laser classification label............................................................................39
Figure 12 Laser warning labels..................................................................................40
Figure 13 Sample laser product safety label on the ONT equipment ........................41
5 XS-240W-A and XS-250WX-A unit data sheet ............................45
Figure 14 XS-240W-A or XS-250WX-A in wall mounting bracket .............................49
Figure 15 XS-240W-A ONT connections...................................................................50
Figure 16 XS-250WX-A ONT connections ................................................................50
Figure 17 XS-250WX-A indoor ONT LEDs................................................................54
Figure 18 Functional blocks for XS-240W-A ONT .....................................................58
Figure 19 Functional blocks for XS-250WX-A ONT...................................................59
Figure 20 XS-240W-A and XS-250WX-A ONT SoC hardware block ........................60
6 Install an XS-240W-A or XS-250WX-A indoor ONT ....................65
Figure 21 XS-240W-A and XS-250WX-A wall mounting bracket ..............................68
Figure 22 XS-240W-A and XS-250WX-A ONT in wall mounting bracket ..................68
Figure 23 XS-240W-A ONT connections...................................................................69
Figure 24 XS-250WX-A connections .........................................................................69
7 Replace an XS-240W-A or XS-250WX-A indoor ONT.................73
Figure 25 XS-240W-A ONT connections...................................................................75
Figure 26 XS-250WX-A ONT connections ................................................................76
8 Configure an XS-240W-A or XS-250WX-A indoor ONT .............79
Figure 27 Web login window......................................................................................80
Figure 28 Device Information window........................................................................81
Figure 29 LAN status window ....................................................................................83
Figure 30 WAN status window...................................................................................85
Figure 31 WAN status IPv6 window ..........................................................................87
Figure 32 Home networking information window.......................................................89
Figure 33 Optics module status window ....................................................................90
Figure 34 Statistics window .......................................................................................92
Figure 35 Voice Information window..........................................................................93
Issue: 01 3FE-48631-AAAA-TCZZA 13
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Figure 36 LAN network window .................................................................................95
Figure 37 LAN IPv6 network window.........................................................................97
Figure 38 WAN network window................................................................................99
Figure 39 WAN DHCP window ................................................................................100
Figure 40 Wireless 2.4GHz network window ...........................................................102
Figure 41 Wireless 5GHz network window ..............................................................105
Figure 42 Wireless Schedule network window ........................................................107
Figure 43 IP Routing network window .....................................................................108
Figure 44 DNS network window ..............................................................................109
Figure 45 TR-069 network window..........................................................................111
Figure 46 QoS Config window (L2)..........................................................................112
Figure 47 Firewall window .......................................................................................114
Figure 48 MAC filter window....................................................................................115
Figure 49 IP filter window ........................................................................................116
Figure 50 URL Filter window ...................................................................................118
Figure 51 DMZ and ALG window.............................................................................119
Figure 52 Access Control window ...........................................................................121
Figure 53 Port forwarding window ...........................................................................123
Figure 54 DDNS window .........................................................................................124
Figure 55 NTP window ............................................................................................125
Figure 56 USB window ............................................................................................126
Figure 57 UPnP and DLNA window.........................................................................128
Figure 58 Voice setting window ...............................................................................129
Figure 59 Password window....................................................................................132
Figure 60 LOID Config window................................................................................133
Figure 61 SLID configuration window......................................................................134
Figure 62 Device management window...................................................................135
Figure 63 Backup and Restore window ...................................................................136
Figure 64 Firmware upgrade window ......................................................................137
Figure 65 Reboot window ........................................................................................138
Figure 66 Factory default window............................................................................139
Figure 67 Diagnose window ....................................................................................140
Figure 68 Log window..............................................................................................141
Figure 69 RG Troubleshooting Counters window....................................................143
14
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
List of tables
2 ETSI ONT safety guidelines .........................................................17
Table 1 Safety labels ..............................................................................................18
4 ANSI ONT safety guidelines ........................................................33
Table 2 Safety labels ..............................................................................................34
5 XS-240W-A and XS-250WX-A unit data sheet ............................45
Table 3 Identification of XS-240W-A indoor ONTs .................................................45
Table 4 Identification of XS-250WX-A indoor ONTs...............................................46
Table 5 XS-240W-A and XS-250WX-A power supply ............................................48
Table 6 XS-240W-A and XS-250WX-A comparison...............................................48
Table 7 XS-240W-A and XS-250WX-A indoor ONT interface connection
capacity .....................................................................................................52
Table 8 XS-240W-A and XS-250WX-A indoor ONT physical connections ............53
Table 9 XS-240W-A and XS-250WX-A indoor ONT LEDs.....................................54
Table 10 XS-240W-A and XS-250WX-A indoor ONT physical specifications ..........55
Table 11 XS-240W-A and XS-250WX-A indoor ONT power consumption
specifications .............................................................................................56
Table 12 XS-240W-A and XS-250WX-A indoor ONT environmental
specifications .............................................................................................56
Table 13 XS-240W-A and XS-250WX-A indoor ONT capacity for GEM ports
and T-CONTs ............................................................................................ 57
Table 14 Responsible party contact information ......................................................62
Table 15 XS-240W-A and XS-250WX-A ONT considerations and limitations .........64
8 Configure an XS-240W-A or XS-250WX-A indoor ONT .............79
Table 16 Device Information parameters .................................................................81
Table 17 LAN status parameters..............................................................................83
Table 18 WAN status parameters ............................................................................85
Table 19 WAN status IPv6 parameters ....................................................................87
Table 20 Home networking parameters ...................................................................89
Table 21 Optics module status parameters..............................................................91
Table 22 Voice Information parameters ................................................................... 93
Table 23 LAN network parameters...........................................................................95
Table 24 LAN IPv6 network parameters...................................................................97
Table 25 WAN network parameters .........................................................................99
Table 26 WAN DHCP parameters..........................................................................101
Table 27 Wireless 2.4GHz network parameters.....................................................102
Table 28 Wireless 5GHz network parameters........................................................105
Table 29 IP Routing network parameters ...............................................................108
Table 30 DNS network parameters ........................................................................110
Table 31 TR-069 network parameters....................................................................111
Table 32 QoS Config parameters...........................................................................113
Table 33 Firewall parameters .................................................................................115
Table 34 MAC filter parameters..............................................................................116
Table 35 IP filter parameters ..................................................................................117
Table 36 URL Filter parameters .............................................................................118
Issue: 01 3FE-48631-AAAA-TCZZA 15
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Table 37 DMZ and ALG parameters ......................................................................119
Table 38 Access control parameters ......................................................................121
Table 39 Port forwarding parameters .....................................................................123
Table 40 DDNS parameters ...................................................................................124
Table 41 USB parameters......................................................................................127
Table 42 Voice setting parameters.........................................................................130
Table 43 Password parameters..............................................................................132
Table 44 LOID configuration parameters ...............................................................133
Table 45 SLID configuration parameters................................................................134
Table 46 Device management parameters ............................................................135
Table 47 RG Troubleshooting Counters parameters..............................................143
16
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
2 ETSI ONT safety guidelines
This chapter provides information about the mandatory regulations that govern the
installation and operation of the optical network terminals (ONTs).
2.1 Safety instructions
This section describes the safety instructions that are provided in the ONT customer
documentation and on the equipment.
2.1.1 Safety instruction boxes
The safety instruction boxes are provided in the ONT customer documentation.
Observe the instructions to meet safety requirements.
ETSI ONT safety guidelines
The following is an example of the Danger box.
Danger — Possibility of personal injury.
The Danger box indicates that the described activity or situation may pose a threat
to personal safety. It calls attention to a situation or procedure which, if not correctly
performed or adhered to, may result in death or serious physical harm.
Do not proceed beyond a Danger box until the indicated conditions are fully
understood and met.
The following is an example of the Warning box.
Warning 1 — Possibility of equipment damage.
Warning 2 — Possibility of data loss.
The Warning box indicates that the described activity or situation may, or will, cause
equipment damage, loss of data, or serious performance problems. It identifies a
possible equipment-damaging situation or provides essential information to avoid the
degradation of system operations or data.
Do not proceed beyond a warning until the indicated conditions are fully understood
and met.
Issue: 01 3FE-48631-AAAA-TCZZA 17
ETSI ONT safety guidelines
The following is an example of the Caution box.
The Caution box indicates that the described activity or situation may, or will, cause
service interruption.
Do not proceed beyond a caution until the indicated conditions are fully understood
and met.
The following is an example of the Note box.
The Note box provides information that assists the personnel working with ONTs. It
does not provide safety-related instructions.
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Caution 1 — Possibility of service interruption.
Caution 2 — Service interruption.
Note — Information of special interest.
2.1.2 Safety-related labels
The ONT equipment is labeled with the specific safety instructions and compliance
information that is related to a variant of the ONT. Observe the instructions on the
safety labels.
Table 1 provides sample safety labels on the ONT equipment.
Table 1 Safety labels
Description Label text
ESD warning Caution: This assembly contains an electrostatic sensitive device.
Laser classification Class 1 laser product
PSE marking These power supplies are Japan PSE certified and compliant with
Figure 1 shows the PSE certification.
Japan VCCI emissions standards.
18
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
This is a Class B product based on the standard of the Voluntary Control Council for Interference
from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in
a domestic environment, it may cause radio interference. Install and use the equipment according
to the instruction manual.
Warning
19841
Guide
Figure 1 PSE certification
2.2 Safety standards compliance
This section describes the ONT compliance with the European safety standards.
ETSI ONT safety guidelines
2.2.1 EMC, EMI, and ESD compliance
The ONT equipment complies with the following EMC, EMI, and ESD requirements:
• EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands
• EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters
(ERM): Telecommunications Network Equipment; Electromagnetic Compatibility
(EMC) requirements; Electrostatic Discharge (ESD) requirements
• EN 55022 (2006): Class B, Information Technology Equipment, Radio
Disturbance Characteristics, limits and methods of measurement
• EN 55024 (2010): Information Technology Equipment, Immunity Characteristics,
limits and methods of measurement
• European Council Directive 2004/108/EC
• EN 300-386 V1.4.1: 2008
• EN 55022:2006 Class B (ONTs)
2.2.2 Equipment safety standard compliance
The ONT equipment complies with the requirements of EN 60950-1, Safety of
Information Technology Equipment for use in a restricted location (per R-269).
Issue: 01 3FE-48631-AAAA-TCZZA 19
ETSI ONT safety guidelines
2.2.3 Environmental standard compliance
The ONT equipment complies with the EN 300 019 European environmental
standards.
2.2.4 Laser product standard compliance
For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for
laser products. If there is an exception to this compliance regulation, you can find this
information in the standards compliance section of the unit data sheet in this Product
Guide.
2.2.5 Resistibility requirements compliance
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
The ONT equipment complies with the requirements of ITU Recommendation K.21
for resistibility of telecommunication equipment installed in customer premises to
over voltage and overcurrents.
2.2.6 Acoustic noise emission standard compliance
The ONT equipment complies with EN 300 753 acoustic noise emission limit and test
methods.
2.3 Electrical safety guidelines
This section provides the electrical safety guidelines for the ONT equipment.
Note 1 — The ONTs comply with the U.S. National Electrical
Code. However, local electrical authorities have jurisdiction
when there are differences between the local and U.S.
standards.
Note 2 — The ONTs comply with BS EN 61140.
20
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
2.3.1 Power supplies
The use of any non-Nokia approved power supplies or power adapters is not
supported or endorsed by Nokia. Such use will void any warranty or support contract
with Nokia. Such use greatly increases the danger of damage to equipment or
property.
2.3.2 Cabling
The following are the guidelines regarding cables used for the ONT equipment:
• All cables must be approved by the relevant national electrical code.
• The cables for outdoor installation of ONTs must be suitable for outdoor use.
• POTS wiring run outside the subscriber premises must comply with the
requirements of local electrical codes. In some markets, the maximum allowed
length of the outside run is 140 feet (43 m). If the outside run is longer, NEC
requires primary protection at both the exit and entry points for the wire.
ETSI ONT safety guidelines
2.3.3 Protective earth
Earthing and bonding of the ONTs must comply with the requirements of local
electrical codes.
2.4 ESD safety guidelines
The ONT equipment is sensitive to ESD. Operations personnel must observe the
following ESD instructions when they handle the ONT equipment.
Caution — This equipment is ESD sensitive. Proper ESD
protections should be used when you enter the TELCO Access
portion of the ONT.
During installation and maintenance, service personnel must wear wrist straps to
prevent damage caused by ESD.
2.5 Laser safety guidelines
Observe the following instructions when you perform installation, operations, and
maintenance tasks on the ONT equipment.
Issue: 01 3FE-48631-AAAA-TCZZA 21
ETSI ONT safety guidelines
18455
Only qualified service personnel who are extremely familiar with laser radiation
hazards should install or remove the fiber optic cables and units in this system.
Observe the following danger for laser hazard. Eyes can be damaged when they are
exposed to a laser beam. Take necessary precautions before you plug in the optical
modules.
2.5.1 Laser classification
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Danger — There may be invisible laser radiation at the fiber
optic cable when the cable is removed from the connector.
Avoid direct exposure to the laser beam.
Danger — Possibility of equipment damage. Risk of eye
damage by laser radiation.
The ONT is classified as a Class 1 laser product based on its transmit optical output.
2.5.1.1 Laser warning labels
The following figures show the labels related to laser product, classification and
warning.
Figure 2 shows a laser product label.
Figure 2 Laser product label
Figure 3 shows a laser classification label. Laser classification labels may be
provided in other languages.
22
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
LASER CLASSE 1CLASE 1 DEL LASER
CLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 1
18992
'
'
Guide
Figure 3 Laser classification label
Figure 4 shows a laser warning label and an explanatory label for laser products.
Labels and warning may be provided in other languages. The explanatory label
provides the following information:
ETSI ONT safety guidelines
• a warning that calls attention to the invisible laser radiation
• an instruction against staring into the beam or viewing directly with optical
instruments
• wavelength
• normal output power
• maximum output power
Issue: 01 3FE-48631-AAAA-TCZZA 23
ETSI ONT safety guidelines
INVISIBLE LASER RADIATION
DO NOT STARE INTO BEAM
OR VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
Wavelength(s): xxxx nm
Normal output power: xx m W
Max output power: yyy m W
Laser Warning Label
Laser Warning Label
CLASS 1 LASER PRODUCT
INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE
WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM.
RAYONNEMENT LASER CLASSE 1
RAYONNEMENT LASER INVISIBLE
EVITER TOUTE EXPOSITION AU FAISCEAU
NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE
CLASE 1 DEL LASER
RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL
RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO
Laser Warning Label
18993
'
Figure 4 Laser warning labels
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
2.5.2 Transmit optical output
The maximum transmit optical output of an ONT is +5 dBm.
2.5.3 Normal laser operation
24
In normal operation, fiber cable laser radiation is always off until it receives signal
from the line terminal card.
Eyes can be damaged when they exposed to a laser beam. Operating personnel
must observe the instructions on the laser explanatory label before plugging in the
optical module.
Danger — Risk of eye damage by laser radiation.
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
2.5.4 Location class
Use cable supports and guides to protect the receptacles from strain.
2.6 Environmental requirements
See the ONT technical specification documentation for more information about
temperature ranges.
During operation in the supported temperature range, condensation inside the ONT
caused by humidity is not an issue. To avoid condensation caused by rapid changes
in temperature and humidity, Nokia recommends:
• The door of the ONT not be opened until temperature inside and outside the
enclosure has stabilized.
• If the door of the ONT must be opened after a rapid change in temperature or
humidity, use a dry cloth to wipe down the metal interior to prevent the risk of
condensation.
• When high humidity is present, installation of a cover or tent over the ONT helps
prevent condensation when the door is opened.
ETSI ONT safety guidelines
Issue: 01 3FE-48631-AAAA-TCZZA 25
ETSI ONT safety guidelines
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
26
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
3 ETSI environmental and CRoHS
guidelines
This chapter provides information about the ETSI environmental China Restriction of
Hazardous Substances (CRoHS) regulations that govern the installation and
operation of the optical line termination (OLT) and optical network termination (ONT)
systems. This chapter also includes environmental operation parameters of general
interest.
3.1 Environmental labels
This section describes the environmental instructions that are provided with the
customer documentation, equipment, and location where the equipment resides.
ETSI environmental and CRoHS guidelines
3.1.1 Overview
CRoHS is applicable to Electronic Information Products (EIP) manufactured or sold
and imported in the territory of the mainland of the People’s Republic of China. EIP
refers to products and their accessories manufactured by using electronic
information technology, including electronic communications products and such
subcomponents as batteries and cables.
3.1.2 Environmental related labels
Environmental labels are located on appropriate equipment. The following are
sample labels.
3.1.2.1 Products below Maximum Concentration Value (MCV) label
Figure 5 shows the label that indicates a product is below the maximum
concentration value, as defined by standard SJ/T11363-2006 (Requirements for
Concentration Limits for Certain Hazardous Substances in Electronic Information
Products). Products with this label are recyclable. The label may be found in this
documentation or on the product.
Issue: 01 3FE-48631-AAAA-TCZZA 27
ETSI environmental and CRoHS guidelines
18986
Figure 5 Products below MCV value label
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label
Figure 6 shows the label that indicates a product is above the maximum
concentration value, as defined by standard SJ/T11363-2006 (Requirements for
Concentration Limits for Certain Hazardous Substances in Electronic Information
Products). The number contained inside the label indicates the Environment-Friendly
User Period (EFUP) value. The label may be found in this documentation or on the
product.
Figure 6 Products above MCV value label
28
3FE-48631-AAAA-TCZZA Issue: 01
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
Together with major international telecommunications equipment companies, Nokia
has determined it is appropriate to use an EFUP of 50 years for network
infrastructure equipment and an EFUP of 20 years for handsets and accessories.
These values are based on manufacturers' extensive practical experience of the
design, manufacturing, maintenance, usage conditions, operating environments,
and physical condition of infrastructure and handsets after years of service. The
values reflect minimum values and refer to products operated according to the
intended use conditions. See “Hazardous Substances Table (HST)” for more
information.
3.2 Hazardous Substances Table (HST)
This section describes the compliance of the OLT and ONT equipment to the CRoHS
standard when the product and subassemblies contain hazardous substances
beyond the MCV value. This information is found in this user documentation where
part numbers for the product and subassemblies are listed. It may be referenced in
other OLT and ONT documentation.
In accordance with the People’s Republic of China Electronic Industry Standard
Marking for the Control of Pollution Caused by Electronic Information Products
(SJ/T11364-2006), customers may access the Nokia Hazardous Substance Table,
in Chinese, from the following location:
ETSI environmental and CRoHS guidelines
• http://www.nokia-sbell.com/wwwroot/images/upload/private/1/media/ChinaRoHS.p
df
3.3 Other environmental requirements
Observe the following environmental requirements when handling the P-OLT or ONT
equipment.
3.3.1 ONT environmental requirements
See the ONT technical specification documentation for more information about
temperature ranges.
3.3.2 Storage
According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in
Class 1.1, weather-protected, temperature-controlled locations.
Issue: 01 3FE-48631-AAAA-TCZZA 29
ETSI environmental and CRoHS guidelines
3.3.3 Transportation
According to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must
be in packed, public transportation with no rain on packing allowed.
3.3.4 Stationary use
According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment
must be in a temperature-controlled location, with no rain allowed, and with no
condensation allowed.
3.3.5 Thermal limitations
When the OLT is installed in the CO or CEV, install air filters on the P-OLT. The
thermal limitations for OLT operation in a CO or CEV are:
7368 ISAM ONT XS-240W-A XS-250WX-A Product
Guide
• operating temperature: 5°C to 40°C (41°F to 104°F)
• short-term temperature: –5°C to 50°C (23°F to 122°F)
• operating relative humidity: 5% to 85%
• short-term relative humidity: 5% to 95%, but not to exceed 0.024 kg of water/kg
3.3.6 Material content compliance
European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain
Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium,
hexavalent chromium, and certain flame retardants in electrical and electronic
equipment. This Directive applies to electrical and electronic products placed on the
EU market after 1 July 2006, with various exemptions, including an exemption for
lead solder in network infrastructure equipment. Nokia products shipped to the EU
after 1 July 2006 comply with the EU RoHS Directive.
Nokia has implemented a material/substance content management process. The
process is described in: Nokia process for ensuring RoHS Compliance
(1AA002660031ASZZA). This ensures compliance with the European Union
Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment (RoHS2). With the process equipment is
assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC)
on Technical documentation for the assessment of electrical and electronic products
with respect to the restriction of hazardous substances.
30
3FE-48631-AAAA-TCZZA Issue: 01
Loading...