Page 1
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support
SERVICE MANUAL
Page (68)
CONFIDENTIAL
1
Level 1&2
Approved 1.0
MGR
09.Jan.2007
RM-156
RM-157
Transceiver characteristics:
Band:
-RM-156: Dual Mode Tri-band phone for GSM 900/1800/1900MHz
and WCDMA Band I
-RM-157: EGSM 900/1800/1900MHz (EDGE only)
Camera: -Main: CMOS, 3.2Mpix (2048x1536), Zoom 3x opt./ 8x digital
- Sub: CIF, (352x288)
Display: -Main LCD: 6,098cm (2.4”) QVGA (240 x 320 pixels) TFT,
16 Million colors
- Sub LCD: 2.794cm (1,1”) OLED (128x36) 65,536 colors
Operating System: Series 60
Bluetooth
IRDA
FM radio
Connector: Pop-Port™ Connector
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Transceiver with BL-5F Li-Ion battery pack
Talk time Standby Note
up to 3h up to 10days
Environmental characteristics:
• Lead-free soldered
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Depends on network
parameters
Page 2
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
2
Approved 1.0
MGR
09.Jan.2007
TABLE OF CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
INTRODUCTION 3
GENERAL REPAIR INFORMATION
PATHFINDER FOR WORKSHOP STAFF
EXPLODED VIEW - UPPER BLOCK
EXPLODED VIEW - LOWER BLOCK
SPARE PARTS OVERVIEW
GENERAL RECYCLING RECOMMENDATION
LEVEL 2 SOLDER COMPONENTS 1
NOKIA ONLINE (NOL) 1
SERVICE TOOLS 1
SW-UPDATE 1
UPPER BLOCK DISASSEMBLY 1
UPPER BLOCK ASSEMBLY 2
LOWER BLOCK DISASSEMBLY 2
LOWER BLOCK ASSEMBLY 3
LEGEND FOR QUICK TROUBLE SHOOTER 4
QUICK TROUBLE SHOOTER - POWER ON 4
QUICK TROUBLE SHOOTER - CHARGING 5
QUICK TROUBLE SHOOTER - NO SERVICE 5
QUICK TROUBLE SHOOTER - WLAN/BLUETOOTH 5
QUICK TROUBLE SHOOTER - EARPIECE 5
QUICK TROUBLE SHOOTER - IHF SPEAKER 5
QUICK TROUBLE SHOOTER - MAIN LCD 5
QUICK TROUBLE SHOOTER - SUB LCD 5
QUICK TROUBLE SHOOTER - MICROPHONE 5
QUICK TROUBLE SHOOTER - CAMCORDER MICROPHONE 5
QUICK TROUBLE SHOOTER - KEYMAT 5
QUICK TROUBLE SHOOTER - ROTATOR SENSOR 6
QUICK TROUBLE SHOOTER - SIDE KEY/ JOYSTICK 6
QUICK TROUBLE SHOOTER - FLASHLIGHT 6
QUICK TROUBLE SHOOTER - FLIP SOFT KEYS 6
QUICK TROUBLE SHOOTER - ZOOM CAPTURE KEY 6
QUICK TROUBLE SHOOTER - CAMERA 6
QUICK TROUBLE SHOOTER - CMOS CAMERA 6
GONOGO TEST 6
BATTERY TEST 6
Page
4
5
6
7
8
9
0
1
2
4
5
0
6
6
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
CHANGE HISTORY
Status Version No. Date Comments
Draft 0.1 24.Nov.2006 Initial draft
Approved 1.0 9.Jan.2007 Approval
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 3
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
3
Approved 1.0
MGR
09.Jan.2007
INTRODUCTION1.
The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to carry out service to
NOKIA products. This Service Manual is to be used only by authorized NOKIA service suppliers, and the content of it is
confidential. Please note that NOKIA provides also other guidance documents (e.g. Service Bulletins) for service suppliers, follow these regularly and comply with the given instructions.
While every endeavor has been made to ensure the accuracy of this document, some errors may exist.
If you find any errors or if you have further suggestions, please notify NOKIA using the address below:
mailto:cc-ts-rc.documentation@nokia.com
Please keep in mind also that this documentation is continuously being updated and modified, so watch always out
for the newest version.
Warnings and Cautions
Please refer to the phone’s user guide for instructions relating to operation, care and maintenance including important safety information. Note also the following:
Warnings:
CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES FITTED WITH ELECTRONIC ENGINE MANAGEMENT SYSTEMS
1.
AND ANTI–SKID BRAKING SYSTEMS. UNDER CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN AFFECT THEIR
OPERATION. IF NECESSARY, CONSULT THE VEHICLE DEALER/MANUFACTURER TO DETERMINE THE IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF ENERGY.
THE HANDPORTABLE TELEPHONE MUST NOT BE OPERATED IN AREAS LIKELY TO CONTAIN POTENTIALLY EXPLOSIVE
2.
ATMOSPHERES, EG PETROL STATIONS (SERVICE STATIONS), BLASTING AREAS ETC.
OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT, INCLUDING CELLULAR TELEPHONES, MAY INTERFERE WITH
3.
THE FUNCTIONALITY OF INADEQUATELY PROTECTED MEDICAL DEVICES. CONSULT A PHYSICIAN OR THE MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE ANY QUESTIONS. OTHER ELECTRONIC EQUIPMENT MAY ALSO BE SUBJECT TO
INTERFERENCE.
Cautions:
1. Servicing and alignment must be undertaken by qualified personnel only.
2. Ensure all work is carried out at an anti–static workstation and that an anti–static wrist strap is worn.
3. Use only approved components as specified in the parts list.
4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing and alignment.
5. Ensure all cables and wires are repositioned correctly.
Electrostatic discharge can easily damage the sensitive components of electronic products.
Therefore every Service Supplier has to take care of all precautions, which are mentioned in the
service level related “Service Partner Requirements”, available on NOKIA Online. Also see ESD
Protection Requirements in this Service Manual.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 4
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
4
(68)
Approved 1.0
09.Jan.2007
GENERAL REPAIR INFORMATION2.
In this section the technician will get some general hints how to carry out repairs:
To familiarize oneself with NOKIA product read the tutorials or user guide on www.nokia.com -->Support-->
•
Phones, by selecting the Phone Model.
Before starting the repair you must take care of ESD precautions like being in your ESD Protected Area and con-
•
necting your wristband.
Use gloves to avoid corrosion and fingerprints.
•
Protect windows and displays with a film to avoid dust and scratches.
•
When cleaning the LCD Module any lint-free cloth can be used (e.g. Micro-Fibre cloth).
•
When cleaning the pads you have to use a soft cloth/ESD brush and Isopropanol. It is not allowed to use a glass
•
fiber pencil because it scratches the surface and will lead later on to corrosion.
Mechanical parts (except shielding lids and bent parts), which didn’t repair the failure, can be reused, if they are
•
not soldered.
When removing the shielding lids make sure to replace them with new ones, otherwise the high-frequency
•
leakage can have an influence on the device.
Always use original NOKIA spare parts.
•
Check the soldering joints of the parts, which are concerned regarding the indicated error (e.g. soldered connec-
•
tors or switches) and resolder them if necessary (Level 2 only).
Remove redundant soldering flux after repair.
•
Meet the torque requirements when assembling the unit (see also the document “torques for transceiver as-
•
sembly” on NOKIA Partner Web Site/NOKIA Online).
Always use your own equipment for testing where you are sure that it works. E.g. if the customer complains
•
about charger function, please test the phone with your own charger to be sure if phone or charger causes the
malfunction.
A SIM card is needed for all GoNoGo tests.
•
When doing the fault log entries, always note the Item code, which caused the malfunction. Also, fill in the ap-
•
propriate part code from the assembly, if needed.
Please be aware that some malfunctions could be software related and solved by an update.
•
MGR
There are several documents available on NOL, which have to be followed:
•
•
First, take care for the latest content pages of Service Bulletins, which are always available for each folder on
•
NOKIA Online. This is also important to recognize, if existing documents have become invalid.
•
The service level indicator at the bottom of each document tells the appropriate destination.
•
Downloads > Support Library >
1. Instructions
2. General Service Bulletins
3. Product related documents
4. Spare Part Service Bulletins
5. Service Tools Service Bulletins
6. Common Software Service Bulletins
etc,…
Use General SB-217 as a reference or overview.
Please also check NOKIA Online (NOL) for latest news and files on a regular basis.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 5
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
5
Approved 1.0
MGR
09.Jan.2007
PATHFINDER FOR WORKSHOP STAFF3.
This is the NOL page (NOKIA Online) which is currently available in Europa, Middle East and Africa only!
In addition to the information in this Service Manual, there are several instructions and information, which have
to be followed. Main documentation database is NOKIA Online with the purpose of serving different multimedia
content, like video clips or interactive tutorials.
It is mandatory to watch for newest technical and organizational information on a daily basis to be updated as
required (see “Latest files in Support Library”). Every new information has to be processed and implemented as
soon as possible.
When logged into NOL you can also find needed information in different folder like:
Support Library
Phones
Service Manuals
Service Bulletins
Software
Repair Information
Level 1&2 e-learning (former NOKIA CarePoint) on NOKIA Online
Former NOKIA CarePoint
content, such as
Online Troubleshooting
•
Product information
•
Videos – Disassembly/Assembly
•
can be found on
NOKIA Online
NOKIA Online
Care Services
Training
Phone Models
Level 1&2 e-learning courses offer a quick overview of the NOKIA phone and support for how to repair and use the
phone:
Overview & Guides
Basic information about the phone,
features and technologies
To reduce the server traffic it is recommended to download newest version of huge files like videos, Phoenix pack
ages or Service Manuals only once and distribute it internally for further use.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Disassembly & Assembly
Instructions how to disassemble and
assemble the phone
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Troubleshooting
Step-by-step instructions on how to
locate and repair the most common
problems with the phone
-
Page 6
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
6
EXPLODED VIEW - UPPER BLOCK4.
See corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL.
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 7
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
7
EXPLODED VIEW - LOWER BLOCK5.
See corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL.
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 8
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
8
SPARE PARTS OVERVIEW6.
See corresponding ITEM/CIRCUIT REF in the Spare Parts Service Bulletins on NOL.
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 9
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
9
GENERAL RECYCLING RECOMMENDATION7.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 10
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
10
LEVEL 2 SOLDER COMPONENTS8.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 11
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
11
(68)
Approved 1.0
09.Jan.2007
NOKIA ONLINE (NOL)9.
NOL is the database where you can find the latest corresponding Service
Bulletins (spare parts, SWAP units and service tools).
This will ensure, that you are using up-to-date order codes only.
Therefore Service Bulletins have to be checked from NOL on daily basis.
MGR
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 12
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
12
SERVICE TOOLS10.
FLS-5 incl. ACF-8, Driver and User Guide
Dongle and flash device incorporated into one package, developed specifically for POS use.
(68)
Approved 1.0
MGR
09.Jan.2007
ACF-8
Universal Power Supply is used to power FLS-4S.
Travel Charger AC-4
Small and lightweight charger for fast charging of your phone
battery.
Internal Battery BL-5F
Inserted under the back cover, this Li-Ion battery provides
power in a lightweight package.
SS-107
Vaccum cap.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
CA-53
Service Cable to connect the PC with the Pop-Port™ connector.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 13
Page
13
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
RJ-110
Soldering Jig
Lead-free Solder Wire
Mandatory for lead-free products (Level 2 only).
(68)
Approved 1.0
MGR
09.Jan.2007
0772040 NMP Standard Toolkit (V2)
For more informations refer to the Service Bulletin (SB-011) on
NOKIA Online.
Supplier or manufacturer contacts for tool re-order can be
found in “Recommended service equipment” document on
NOKIA Online.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 14
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
14
Approved 1.0
09.Jan.2007
SW-UPDATE11.
Flash Concept – (Point of Sales)
To use FLS-5 Flash Dongle you have to follow the user guide inside the sales package. Please check always for the
latest version of flash software, which is available on
NOKIA Online.
MGR
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 15
Page (68)
15
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
UPPER BLOCK DISASSEMBLY12.
Approved 1.0
MGR
09.Jan.2007
1. Needed tools: a torx driver, a torque driver, a torx plus size
6 bit, metal tweezers, angled tweezers, a dental pick, a at
bladed screwdriver, the SS-93, the SS-107 vacuum cap and the
SRT-6.
3. Position the SS-107 on the SUB LCD WINDOW as shown.
2. Remove the battery if inserted.
4. Press down the lever to create vacuum in the cup.
5. Carefully, pull at the grip to lift a bit the SUB LCD WINDOW.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
6. Place the SS-93 between the SUB LCD WINDOW and the FLIP
B-COVER and separate the parts from each other.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 16
Page (68)
16
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
Approved 1.0
MGR
09.Jan.2007
7. Do not use the window again.
9. Only discard the FLIP B-COVER when the adhesive is gluing
strongly and can not be removed completely.
8. Remove the remaining adhesive.
10. Undo the screws in the order shown...
11. ...and remove them.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
12. Slide the SRT-6 along the sides of the FLIP B-COVER to release
all clips.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 17
Page
17
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
13. Remove the FLIP B-COVER.
15. Use the SS-93 as a support when opening the HINGE
connectors.
14. Protect the SUB LCD with a protective lm.
16. Carefully lever up both connectors with angled tweezers.
17. Undo the screws in the order shown...
Service Manual N93i-1 RM-156/ N93i-5 RM-157
18. ...and discard them.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 18
Page
18
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
19. Loosen the ex of the DETECTOR SWITCH.
21. Open the MAIN LCD connector.
20. Open a bit the HINGE as shown and separate the upper parts
from the LOWER BLOCK.
22. Lever up the FLIP FRAME ASSY and remove it from the FLIP
A-COVER.
23. Remove the MAIN LCD.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
24. Now, lever the EARPIECE from its guidance...
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 19
Page
19
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
25. ...and remove the EARPIECE GASKET.
27. Open the SUB LCD connector...
26. Use the dental tool to remove the FLIP SOFT KEYMAT.
28. ...and remove the SUB LCD.
29. Now, the disassembly procedure is complete.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 20
Page
20
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
UPPER BLOCK ASSEMBLY 13.
(68)
Approved 1.0
MGR
09.Jan.2007
1. Assembly
3. Always use a new EARPIECE GASKET when replacing the
EARPIECE.
2. Carefully place the FLIP SOFT KEYMAT into its place.
4. Mind the spring contacts while handling the EARPIECE.
5. Place the MAIN LCD on to the FLIP FRAME ASSY.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
6. Aligne the FLIP A-COVER with the FLIP FRAME ASSY…
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 21
Page
21
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
7. …and cover the MAIN LCD with a protective lm.
9. Close the MAIN LCD connector.
8. Gently turn the assembly as shown and ensure that the FLIP
FRAM ASSY and the MAIN LCD are correctly placed onto the FLIP
A-COVER.
10. Place the SUB LCD on to the FLIP FRAME ASSY…
11. Close the SUB LCD connector.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
12. Align the FLIP A-COVER with the HINGE ASSEMBLY.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 22
Page
22
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
13. Take special care to the ex of the DETECTOR SWITCH.
15. Always use new screws…
14. Set the correct torque.
16. ...and tighten them to the correct torque in the order shown.
17. Fix the DETECTOR SWITCH to its place and adhere the ex as
shown.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
18. Check its correct position.
Page 23
Page
23
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
19. Open the unit as shown...
21. Very gently, close the both HINGE connectors.
20. ...and check the functionality of the switch by turning the
FLIP A-COVER to both directions.
22. Ensure that the cable is not positioned over the screw.
23. Remove the protective lm.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
24. Align the FLIP B-COVER with the FLIP A-COVER and press them
together.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 24
Page
24
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
25. Always use new screws…
27. Remove the protective lm from the new SUB LCD
WINDOWS ASSY…
26. ..and tighten them to the correct torque in the order shown.
28. and align it exactly with the FLIP B-COVER.
29. Secure the window by pressing it into the FLIP B-COVER.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
30. Check that no gaps remain.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 25
Page
25
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
31. Finally t the GRIP C-COVER ASSY.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 26
Page
26
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
LOWER BLOCK DISASSEMBLY14.
(68)
Approved 1.0
MGR
09.Jan.2007
1. Needed Tools: a Torx driver, a torque driver, a Torx Plus size
6 bit, a at bladed screwdriver, a dental pick, metal tweezers,
angled tweezers, the SS-93 and the DC-plug.
3. Optionally the KEYMAT can be removed now. Lift the KEYMAT
with the SS-93 as shown.
2. Cover all windows with a protective lm.
4. Loosen it from the GRIP A-COVER...
5. ...and discard it.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
6. Ensure that no adhesive residuse.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 27
Page
27
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
7. Unlock and remove the GRIP C-COVER.
9. Remove the screws.
8. Undo the four Torx Plus size 6 screws in the order shown.
10. Open the SD-HATCH.
11. Unlock and remove the ORNAMENT R ASSY with the SIDE
KEYMAT.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
12. Open the POP-PORT HATCH.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 28
Page
28
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
13. Use the SS-93 as a lever to unglue the ORNAMENT L ASSY
(INCL. ADHESIVE). Do not reuse it.
15. Open the unit.
14. Remove the adhesive remain.
16. Unlock all snaps of the GRIP B-COVER.
17. Close the unit.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
18. Unlock the last two snaps on the hinge side and remove the
GRIP B-COVER.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 29
Page
29
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
19. Unsnap and remove the BT/WL ANTENNA.
21. Lift the GRIP INNER FRAME a bit and remove the ANTENNA
ASSY.
20. Remove the POP-PORT HATCH.
22. Lift up the LABEL PLATE and remove it.
23. Use angled tweezers to open the HINGE connectors.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
24. Place the tip of the tweezers exactly under the connector
plug and carefully lever it up as shown.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 30
Page
30
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
25. Open the handset...
27. Now, open the Camera CABLE ASSY carefully…
26. ...and gently separate the Upper Block from the Lower parts.
28. ...and remove the CAMERA ASSEMBLY.
29. Lift the ENGINE MODULE from the GRIP A-COVER...
Service Manual N93i-1 RM-156/ N93i-5 RM-157
30. ...and turn it to the angle of 90°.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 31
Page
31
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
31. Gently open the UI ASSY connector...
33. The MICROPHONE and the DC-JACK can be removed easily.
32. ...and remove the ENGINE MODULE.
34. Remove the JOYSTICK HAT.
35. Loosen the ex of the DIGITAL MUSIC ASSY…
Service Manual N93i-1 RM-156/ N93i-5 RM-157
36. ...and gently open the connector.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 32
Page
32
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
37. Separate the parts from each other.
39. Lift the UI ASSY from the GRIP A-COVER and remove it.
38. Bend a bit the GRIP A-COVER to unsnap the UI ASSY.
40. Separate the KEYMAT from the GRIP A-COVER and discard it.
41. Remove the PILLOW with the SS-93.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
42. Remove the GRIP BUMPER by pushing it out from the inner
side of the cover.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 33
Page
33
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
43. Unlock the SIM SHIELD COVER with the dental pick…
45. Open the CABLE CLAMP...
44. ... and remove it.
46. ...and take out the hinge cables from their guide.
47. Undo the two Torx Plus size 6 screws in the order shown…
Service Manual N93i-1 RM-156/ N93i-5 RM-157
48. ...and discard them.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 34
Page
34
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
49. Gently separate the GRIP INNER FRAME from the UPPER
BLOCK.
51. Press on the metal hooks on both sides of the CAMERA
MODULE.
50. Carefully open the CABLE ASSY connector and remove it.
52. Pull out the CAMERA BEZEL with the LENS CUP ASSY from the
CAMERA SUPPORT FRAME ASSY.
53. Unlock the snap...
Service Manual N93i-1 RM-156/ N93i-5 RM-157
54. ...and separate the CAMERA MODULE from the SUPPORT
FRAME ASSY. Do not reuse the CAMERA SUPPORT FRAME
ASSY.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 35
Page
35
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
55. Release the snaps of the CAPTURE KEY INNER COVER.
57. Remove the CAPTURE KEY BUTTON, ZOOM KEY LEVER and
the CAPTURE RETURN SPRING.
56. Now, remove the CAPTURE KEY COVER PAINTED.
58. Remove the CAPTURE KEY INNER COVER.
59. Now, the disassembly procedure is complete.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
60.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 36
Page
36
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
LOWER BLOCK ASSEMBLY15.
(68)
Approved 1.0
MGR
09.Jan.2007
1. Assembly
3. Place the CAPTURE KEY BUTTON in to its place.
2. Place the ZOOM KEY LEVER PAINTED into the CAPTURE KEY COVER
PAINTED as shown.
4. Set the recess of the ZOOM KEY LEVER in position shown.
5. Place the CAPTURE RETURN SPRING in to its place.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
6. Carefully, press the HINGE ASSEMBLY into the CAPTURE KEY
COVER.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 37
Page
37
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
7. Fit the CAPTURE KEY INNER COVER as shown.
9. ...and secure the parts by pressing them together.
8. Now, check the correct position of the ZOOM KEY LEVER...
10. Be sure that all GROUND CLIPS are into their places.
11. Always use a new CABLE CLAMP. Align the CABLE CLAMP
with the GRIP INNER FRAME and push it into its place.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
12. Fit a new CUSHION.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 38
Page
38
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
13. Feed the HINGE cables into the opening of the GRIP INNER
FRAME.
15. Set torque driver to the correct torque.
14. Position the GRIP INNER FRAME onto the HINGE ASSEMBLY.
16. Always use new screws.
17. Tighten the SCREWS in the order shown.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
18. Fit the SIM SHIELD COVER.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 39
Page
39
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
19. Ensure that the adhesive is glued into the shown place.
21. Place the SS-93 as a support between the CABLE CLAMP and
the GRIP INNER FRAME...
20. Place the HINGE cables into the guide of the GRIP INNER
FRAME.
22. ...and close the CABLE CLAMP.
23. Fit a new GRIP BUMPER and secure it by pressing into place.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
24. Fit the PILLOW.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 40
Page (68)
40
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
Approved 1.0
MGR
09.Jan.2007
25. Insert the UI ASSY and secure it by closing all snaps.
27. Very gently, close the connector with the SS-93.
26. Fit the DIGITAL MUSIC ASSY into the GRIP A-COVER.
28. Insert the MICROPHONE avoiding bending the spring contacts.
29. Fit the DC-JACK with the DC-plug.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
30. Fit the JOYSTICK HAT.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 41
Page
41
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
31. Carefully connect the UI ASSY to the ENGINE MODULE.
33. Note the correct position of the guide pin at the camera
side...
32. Turn the ENGINE MODULE as shown and align it with the GRIP
A-COVER.
34. ...and at the card holder side.
35. Gently, bend the hooks back into its position as shown.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
36. Always use a new CAMERA SUPPORT FRAME ASSY.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 42
Page
42
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
37. Insert the CAMERA MODULE into the FRAME.
39. Fit the CAMERA BEZEL with the LENS CAP ASSY.
38. Squeeze the CAMERA SUPPORT FRAME ASSY until it close.
40. Ensure that the hooks hold well the CAMERA BEZEL.
41. Note the correct direction of the CABLE ASSY.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
42. Connect the cable side with blue mark to the CAMERA
MODULE...
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 43
Page
43
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
43. ...and the other side of the cable to the ENGINE MODULE.
45. ...and place it into position.
44. Turn the CAMERA MODULE as shown...
46. Check the correct position of the CABLE ASSY.
47. Align the GRIP INNER FRAME with the GRIP A-COVER
avoiding squeezing the CABLE ASSY.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
48. Close the unit...
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 44
Page
44
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
49. ...and carefully close the connectors.
51. Fit the LABEL PLATE.
50. Ensure that the cable is positioned correctly to avoid
squeezing it when assembling the LABEL PLATE.
52. Lift the GRIP INNER FRAME a bit and gently place the ANTENNA
into its position.
53. Fit the POP-PORT HATCH.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
54. Fit the BT WL ANTENNA into its place.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 45
Page
45
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
55. Align the GRIP B-COVER with the GRIP A-COVER.
57. Open the unit...
56. First close the snaps on the hinge side.
58. ...and then close the remaining snaps.
59. Insert the screws.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
60. Set the torque driver to the correct torque.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 46
Page
46
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
61. To prevent damaging the plastic threads, rst turn the
screws to the left...
63. Fit the ORNAMENT R ASSY with the SIDE KEYMAT.
62. ... and then tighten them to the correct torque in the order
shown.
64. Close the SD HATCH.
65. Remove the protective lm of the ORNAMENT L ASSY...
Service Manual N93i-1 RM-156/ N93i-5 RM-157
66. ...and t the ORNAMENT L ASSY into its place.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 47
Page
47
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
(68)
Approved 1.0
MGR
09.Jan.2007
67. Open the unit...
69. Place it exactly into its place...
68. Always use a new KEYMAT when assembling the unit.
70. ...and secure by pressing evenly.
71. Check that no gaps remain.
Service Manual N93i-1 RM-156/ N93i-5 RM-157
72. Finally t the GRIP C-COVER ASSY.
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 48
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
48
LEGEND FOR QUICK TROUBLE SHOOTER16.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 49
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
49
QUICK TROUBLE SHOOTER - POWER ON17.
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 50
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
50
QUICK TROUBLE SHOOTER - CHARGING18.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 51
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
51
QUICK TROUBLE SHOOTER - NO SERVICE19.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 52
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
52
QUICK TROUBLE SHOOTER - WLAN/BLUETOOTH20.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 53
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
53
QUICK TROUBLE SHOOTER - EARPIECE21.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 54
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
54
QUICK TROUBLE SHOOTER - IHF SPEAKER 22.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 55
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
55
QUICK TROUBLE SHOOTER - MAIN LCD 23.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 56
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
56
QUICK TROUBLE SHOOTER - SUB LCD 24.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 57
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
57
QUICK TROUBLE SHOOTER - MICROPHONE 25.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 58
Page (68)
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
58
QUICK TROUBLE SHOOTER - CAMCORDER MICROPHONE26.
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 59
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
59
QUICK TROUBLE SHOOTER - KEYMAT27.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 60
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
60
QUICK TROUBLE SHOOTER - ROTATOR SENSOR28.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 61
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
61
QUICK TROUBLE SHOOTER - SIDE KEY/ JOYSTICK29.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 62
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
62
QUICK TROUBLE SHOOTER - FLASHLIGHT30.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 63
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
63
QUICK TROUBLE SHOOTER - FLIP SOFT KEYS 31.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 64
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
64
QUICK TROUBLE SHOOTER - ZOOM CAPTURE KEY32.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 65
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
65
QUICK TROUBLE SHOOTER - CAMERA33.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 66
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
66
QUICK TROUBLE SHOOTER - CMOS CAMERA34.
(68)
Approved 1.0
MGR
09.Jan.2007
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 67
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
67
(68)
Approved 1.0
09.Jan.2007
GONOGO TEST35.
To test the Camera, Bluetooth and IRDA functionality refer to the phone User`s
guide.
MGR
The User´s Guide is available on
Before starting the
GoNoGo test, check that
camera window is clean.
If not, clean the window
with cloth.
Bluetooth test
You need another Bluetooth device (e.g. 6230) to do a GoNoGo test.
Make sure that Bluetooth is activated in the reference unit. The distance of the devices should be not more than 5m
from each other.
www.nokia.com.
Infrared test
You need another infrared device (e.g. 6230) to do a GoNoGo test. The infrared windows of the devices must be
directed to each other and should have a distance of approximate 15 cm. Make sure that infrared is activated in
receiver device.
Warning: Do not point the IR (infrared) beam at anyone’s eye or allow it to interfere with other IR devices. This
device is a Class 1 Laser product.
Reference unit, Bluetooth /infrared activated Test unit
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Page 68
Page
CMO Operations & Logistics
Training and Vendor Development
Multimedia Creation & Support CONFIDENTIAL
68
BATTERY TEST36.
A battery tester lets you test the capacity of NOKIA batteries.
Please refer to the actual information on NOKIA Online.
(68)
Approved 1.0
MGR
09.Jan.2007
http://www.astratec.co.uk/
http://www.cadex.com/
Service Manual N93i-1 RM-156/ N93i-5 RM-157
Copyright © 2006-2007 NOKIA Corporation. All rights reserved.
Loading...