Programs After Market Services (PAMS)
Technical Documentation
[Issue 3: NMP Part No.0275426 ]
[Issue 4: NMP Part No.0275571]
NSM–3/3D
SERIES CELLULAR
PHONES
NSM–3 issue 4: 02/2002
Copyright 2000, 2002. Nokia Corporation. All Rights Reserved.
NSM–3/3D
Foreword
PAMS Technical Documentation
AMENDMENT RECORD SHEET
Amendment Date Inserted By Comments
Issue 1 12/1999 Jouni Rantala
Issue 2 07/2000 Jouni Rantala General Information
HHS–12 Swivel Mount added.
ACP–7P charger removed.
System Module
Parts List and Schematic Diagrams for
layout 16 added.
UI Module
IR Module text edited.
Product Variants
Exploded View and Item numbering
edited.
Service Software Instructions
Edited to correspond with changes
made in Service Software.
Issue 3 11/2000 Jouni Rantala
Issue 4 12/2001 O Juntunen
Non Serviceable Accessories
HHS–12 Swivel Mount added.
ACP–7P charger removed.
NSM–3DX phone added.
NSM–3 layout 18
Schematic Diagrams for layout version
16 can be used with layout 18 (top
and bottom layout pictures added for
version 18).
Note: Issue 3 replaces
issues 1 and 2.
Foreword pp.1 to 4 replaced
System Module
TOC updated
Parts List for NSM–3 layouts 19 and
21 added,
NSM 3D layout 05 added,
HW list added.
Schematic Diagrams for NSM–3
layout 19, 20, 21 added
Schematic Diagrams for NSM–3D
layout 05 added. Document
repaginated.
Page 2
2002. Nokia Corporation.
Issue 4 02/2002
PAMS Technical Documentation
NSM–3/3D
Foreword
Product Variants
Exploded View and Item numbering
updated
Replace pp 1 & 2, 5 to 8
Service Software Instructions
Edited to correspond with changes
made in Service Software. Tuning
Instructions pp. 83–100 to removed to
dedicated section.
Replaced pages: pp.1 to 6, 10, 14, 16,
27, 32, 39, 45, 48, 51 to 58, 64, 68, 71
to 82.
Tuning Instructions
Removed from Service SW section.
28 pages.
Service Tools
pp 1 to 3, p.11, p.25, p.27 edited.
p.13 JBA–6 replaced by BBF–1
p.14 ADS–3 removed
p.26 Modular Cable Jack removed
p.28 FLS–4s updated.
Issue 4 02/2002
Nokia Mobile Phones Ltd.
Page 3
NSM–3/3D
Foreword
PAMS Technical Documentation
NSM–3/3D
SERIES CELLULAR PHONES
SERVICE MANUAL
CONTENTS:
1. Foreword
2. General Information
3. System Module
4. UI Module
5. Product Variants
NSM–3NX
NSM–3DX
6. Service Software Instructions
6. Tuning Instructions
8. Service Tools
9. Disassembly/Troubleshooting Instructions
10. Non–serviceable Accessories
Page 4
2002. Nokia Corporation.
Issue 4 02/2002
PAMS Technical Documentation
This document is intended for use by qualified service personnel only.
Company Policy
Our policy is of continuous development; details of all technical modifications will
be included with service bulletins.
While every endeavour has been made to ensure the accuracy of this document,
some errors may exist. If any errors are found by the reader, NOKIA MOBILE
PHONES Ltd should be notified in writing.
Please state:
Title of the Document + Issue Number/Date of publication
Latest Amendment Number (if applicable)
Page(s) and/or Figure(s) in error
NSM–3/3D
Foreword
IMPORTANT
Please send to: Nokia Mobile Phones Ltd
PAMS Technical Documentation
PO Box 86
24101 SALO
Finland
Issue 4 02/2002
Nokia Mobile Phones Ltd.
Page 5
NSM–3/3D
Foreword
Warnings and Cautions
Please refer to the phone’s user guide for instructions relating to operation,
care and maintenance including important safety information. Note also the
following:
Warnings:
1. CARE MUST BE TAKEN ON INSTALLATION IN VEHICLES
FITTED WITH ELECTRONIC ENGINE MANAGEMENT
SYSTEMS AND ANTI–SKID BRAKING SYSTEMS. UNDER
CERTAIN FAULT CONDITIONS, EMITTED RF ENERGY CAN
AFFECT THEIR OPERATION. IF NECESSARY, CONSULT THE
VEHICLE DEALER/MANUFACTURER TO DETERMINE THE
IMMUNITY OF VEHICLE ELECTRONIC SYSTEMS TO RF
ENERGY.
2. THE HANDPORTABLE TELEPHONE MUST NOT BE OPERATED
IN AREAS LIKELY TO CONTAIN POTENTIALLY EXPLOSIVE
ATMOSPHERES EG PETROL STATIONS (SERVICE STATIONS),
BLASTING AREAS ETC.
PAMS Technical Documentation
3. OPERATION OF ANY RADIO TRANSMITTING EQUIPMENT,
4. CLASS 1 LASER PRODUCT. See IEC60825–1 specification:
Cautions:
1. Servicing and alignment must be undertaken by qualified
2. Ensure all work is carried out at an anti–static workstation and that
3. Ensure solder, wire, or foreign matter does not enter the telephone
4. Use only approved components as specified in the parts list.
5. Ensure all components, modules screws and insulators are
INCLUDING CELLULAR TELEPHONES, MAY INTERFERE WITH
THE FUNCTIONALITY OF INADEQUATELY PROTECTED
MEDICAL DEVICES. CONSULT A PHYSICIAN OR THE
MANUFACTURER OF THE MEDICAL DEVICE IF YOU HAVE
ANY QUESTIONS. OTHER ELECTRONIC EQUIPMENT MAY
ALSO BE SUBJECT TO INTERFERENCE.
825–1; 5: Labelling, 5.1: General, 5.2: Class 1
personnel only.
an anti–static wrist strap is worn.
as damage may result.
correctly re–fitted after servicing and alignment. Ensure all cables
and wires are repositioned correctly.
6. All PC’s used with NMP Service Software for this produce must be
bios and operating system ”Year 2000 Compliant”.
Page 6
2002. Nokia Corporation.
Issue 4 02/2002
Loading...