Page 1
DRIVER CONTROLS
A
B
SECTION HRN
CONTENTS
PRECAUTION ............................................... 2
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................
WIRING DIAGRAM ....................................... 3
HORN
HORN ................................................................. 3
Wiring Diagram ......................................................... 3
REMOVAL AND INSTALLATION ................ 7
HORN ................................................................. 7
2
Removal and Installation .......................................... 7
C
D
E
F
G
H
I
J
K
HRN
M
N
O
P
Revision: August 2012 2012 Maxima
HRN-1
Page 2
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
INFOID:0000000007253246
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: August 2012 2012 Maxima
HRN-2
Page 3
< WIRING DIAGRAM >
HORN
WIRING DIAGRAM
HORN
Wiring Diagram INFOID:0000000007253247
A
B
C
D
E
F
G
H
I
J
K
HRN
M
N
O
P
ABLWA1570GB
Revision: August 2012 2012 Maxima
HRN-3
Page 4
< WIRING DIAGRAM >
HORN
ABLIA1729GB
Revision: August 2012 2012 Maxima
HRN-4
Page 5
< WIRING DIAGRAM >
HORN
A
B
C
D
E
F
G
H
I
J
K
HRN
M
N
O
ABLIA1730GB
Revision: August 2012 2012 Maxima
HRN-5
P
Page 6
< WIRING DIAGRAM >
HORN
ABLIA1731GB
Revision: August 2012 2012 Maxima
HRN-6
Page 7
< REMOVAL AND INSTALLATION >
HORN
REMOVAL AND INSTALLATION
HORN
Removal and Installation INFOID:0000000007253248
REMOVAL
1. Remove the engine side cover. Refer to EXT-15, "Exploded View".
2. Position aside the front fender protector LH. Refer to EXT-23, "Removal and Installation"
3. Disconnect the horn connectors (A).
4. Remove the horn bracket bolt (B), and remove horn (1) and horn
(2).
INSTALLATION
Installation is in the reverse order of removal.
.
ALLIA0874ZZ
A
B
C
D
E
F
G
H
I
J
K
HRN
M
N
O
P
Revision: August 2012 2012 Maxima
HRN-7
Loading...