NISSAN GT R Service Maintenance Guide 2013
2013
SERVICE AND
MAINTENANCE GUIDE
TABLE OF CONTENTS
OWNER’S LITERATURE INFORMATION ..................................2
INTRODUCTION
NISSAN Maintenance ..............................................3
Why NISSAN Service? .............................................4
NISSAN MAINTENANCE & REPAIR SUPPORT
Extended Service Plans .............................................9
Genuine NISSAN Collision Parts .......................................10
Genuine NISSAN Parts You Can Rely On .............................57,61,69,73
NISSAN Services Designed With You in Mind ................................65
SCHEDULED MAINTENANCE GUIDE
GT-R Performance Optimization Services .............................42,44,46,48
Determining the Proper Maintenance Interval .................................11
Explanation of Scheduled Maintenance Items ................................12
AdditionalMaintenanceItems .........................................14
Setting Guide of Wheel Alignment Depending on the Customer’s Driving .................37
Tire Replacement Record ...........................................38
Transmission Assembly Replacement Record ................................40
Maintenance Schedule .............................................41
Maintenance Log ................................................76
1
OWNER’S LITERATURE INFORMATION
INDEX OF TOPICS WHERE TO FIND INFORMATION
Recommended Fuel, Lubricants, Fluids ............ Owner’s Manual: chapter 9
Starting and Driving Your Vehicle ................ Owner’s Manual: chapter 5
Security System Operation .................... Owner’s Manual: chapter 2
Changing a Flat Tire ......................... Owner’s Manual: chapter 6, also see chapter 8
New Vehicle Limited Warranty .................. “2013 New Vehicle Limited Warranty” section in
Warranty Information Booklet
Federal Emission Control Warranties ............. “Federal Vehicle Emission Control Limited Warranties”
section in Warranty Information Booklet
California Emission Control Warranties ............ “California Vehicle Emission Control Warranties”
section in Warranty Information Booklet
Tire Pressure/Rotation ....................... Owner’s Manual: chapter 8
Tire Warranties/Safety Information ............... Individual tire manufacturer warranty sections in
Warranty Information Booklet
Consumer Affairs Assistance ................... “Nissan’s Customer Care Program” section in Warranty
Information Booklet and “Overview” section in
Customer Care/Lemon Law Information Booklet
Do It Yourself Information ...................... Owner’s Manual: chapter 8
General Maintenance ........................ Owner’s Manual: chapter 8
*
* Not applicable outside the United States
2
NISSAN MAINTENANCE
Maintain Your Investment
Preventative scheduled maintenance is an important investment to optimize the performance, reliability,
safety and resale value of your NISSAN GT-R. Scheduling your vehicle’s maintenance at the
recommended intervals will ensure your vehicle is running at its best.
We want you to enjoy your NISSAN GT-R. This Service and Maintenance Guide is designed to help
you make sure your vehicle receives proper and timely maintenance that is necessary. Key services are
explained in detail, along with an outline of scheduled maintenance to help you maintain your vehicle.
Your GT-R certified NISSAN dealer can assist you in determining the best schedule based on your
driving habits and local conditions.
Failure to perform scheduled maintenance may result in excluding portions of your vehicle from
warranty coverage and may reduce the performance, safety, reliability and/or resale value of your
vehicle. For details of the warranty, please read the 2013 NISSAN GT-R Warranty Information Booklet.
3
WHY NISSAN SERVICE?*
As to specific service to the GT-R, special skills, knowledge and equipment are necessary to properly inspect
and adjust the GT-R engine, transmission, suspension
and brakes to maintain performance. A GT-R certified
NISSAN dealer has the GT-R certified technical staff and
the special equipment to properly maintain your GT-R.
Many general maintenance items can be performed at all
NISSAN dealers. However, make sure the specified other
fluids and parts are used when the maintenance is performed.
GENUINE SERVICE
4
WHY NISSAN SERVICE?*
GENUINE SERVICE
To safeguard the quality, reliability and safety of your vehicle, a GT-R certified NISSAN dealer is recommended for
maintenance or repair. Only GT-R certified NISSAN dealers offer you these advantages:
● NISSAN trained and certified GT-R technicians
● Immediate access to warranty service history and NISSAN technical information
● Latest diagnostic, special tools and service techniques
● Genuine NISSAN Parts that meet NISSAN’s demanding standards
● 12 month/12,000 mile parts and labor limited warranty when Genuine NISSAN Parts are installed by your dealer
● Lifetime limited warranty on select replacement parts
● Clear, up-front estimates
● Nearly 700 GT-R certified locations nationwide
● Shuttle service/Courtesy van (at participating dealers)
● Access to a NISSAN GT-R certified body repair facility
Your GT-R certified NISSAN dealer is a full-service maintenance and repair center. We recommend using authorized
NISSAN Service and Genuine NISSAN Parts that we have designed for their reliability, safety and suitability for your
NISSAN vehicle. We are committed to providing you with quick, efficient and competitively priced service and parts.
*
* May differ or not apply outside the United States, please inquire of your dealer.
5
NISSAN MAINTENANCE
About GT-R Maintenance
The GT-R is Nissan’s first supercar category vehicle. The GT-R is equipped with special systems.
These systems are different than those used on conventional vehicles to allow for the high
performance driving characteristics of the GT-R. Your GT-R should be maintained by a GT-R certified
NISSAN dealer. Special skills, knowledge and equipment are necessary to properly maintain your
GT-R.
Special skill, knowledge and equipment are necessary to properly inspect and adjust the GT-R
engine, transmission, suspension and brakes to maintain performance. A GT-R certified NISSAN
dealer has the GT-R certified technical staff and the special equipment to properly maintain your
GT-R.
Nissan recommends maintenance items that require the replacement of parts, engine oil, oil filters,
and air filters should be performed by a GT-R certified dealer. Make sure the specified fluids and parts
are used when the maintenance is performed. NISSAN also recommends the replacement of parts
such as the brakes should be performed by a GT-R certified dealer.
For recommended and/or required GT-R lubricants and fluids, refer to Chapter 9 of your owner’s
manual.
6
NISSAN MAINTENANCE
GT-R Performance Optimization Services
In addition to the regular maintenance recommended by NISSAN, the GT-R requires the following Inspections;
Measurement and adjustment of wheel alignment if needed (unladen with fuel and lubricants full, including tire
pressure adjustment) Note 1
● Note 1: This vehicle is equipped with a high performance suspension. As the suspension components ⬙break-in⬙, the
vehicle’s wheel alignment needs to be measured and adjusted by a GT-R certified dealer at the recommended intervals.
Preventing Toe-Out: Toe-out can cause uneven tire wear or damage to areas inside the tires due to high heat. Be sure
to have the wheel alignment toe-in setting checked and adjusted by your GT-R certified NISSAN dealer before any
performance driving on closed circuit tracks. Obey all traffic laws when on public roads.
Toe-in specification
Front: 0.059 in (1.5 mm)
Rear: 0.079 in (2.0 mm)
Engine settings (balancing of air flow for left and right banks) Note 2
● Note 2: Each cylinder bank of this engine operates independently due to the vehicle’s twin turbocharger design. Each
side of the engine must operate at the same level of performance. The air flow of each bank must be checked and
adjusted as necessary by a GT-R certified NISSAN dealer.
Increase tightening of the drive shaft and center nut on hub Note 3
● Note 3: During the first GT-R special inspection (after driving 1,000 miles), the front and rear wheel hub lock nuts
(each one on the left and right sides) must be tightened to the specified tightening specification. The wheel lock nuts
should be properly tightened every time the inspection is performed.
Transmission settings Note 4
● Note 4: The design of the clutch and transmission requires inspection and adjustment of the clutch and shift forks by a
GT-R certified NISSAN dealer at the recommended intervals. Depending on driving conditions, more frequent
adjustments may be necessary to help maximize vehicle performance.
7
NISSAN MAINTENANCE
Checking the exhaust finisher and rear bumper clearance Note 5
● Note 5: Clearance between the enlarged-diameter exhaust finisher and the rear bumper is realized by using highly rigid
exhaust mount rubber to control rear muffler vibration. The clearance between the exhaust finisher and the rear bumper
may alter as the exhaust mount rubber changes shape due to vibration, passage of time and high exhaust temperature
during high performance driving. Therefore, inspection of the clearance is necessary during the GT-R special inspection
and when engaging in performance driving.
Increase tightening of the strut support bar attachment section with the shock absorber Note 6
● Note 6: During the first GT-R special inspection (after 1,000 miles), the strut support bar attachment bracket and
shock absorber (each one on the left and right sides) must be tightened to the specified tightening specification. The
strut support bar attachment bracket and shock absorber (each one on the left and right sides) must be tightened to
the specified tightening specification 300-600 miles (500-1000 km) after the support bar or shock absorber have
been removed or installed.
As a condition of warranty, the above six inspections are required at the following intervals: 1,000 miles, 12 months, 24
months and 36 months. These inspections will be performed free of charge at a GT-R certified Nissan dealer only. All
inspections and services on the above six items, performed outside the above intervals, are performed at the
customer’s expense. See your 2013 Nissan GT-R Warranty Information Booklet for details.
After the period of GT-R performance optimization services in the first three years, these items are included in the
regular scheduled maintenance.
*Repairs and adjustments involving part replacement, etc. determined to be necessary as a result of these inspections
are performed at the customer’s expense.
*See your 2013 NISSAN GT-R Warranty Information Booklet for significant limitations, exclusions, and possible voiding
of warranty resulting from failure to have these necessary inspections, repairs and/or adjustments performed.
8
EXTENDED SERVICE PLANS*
If someone told you, you could drive your new GT-R for the
next 7 years or 100,000 miles, almost worry-free of unexpected repair costs, would you be interested?
NISSAN’s “Security+Plus” family of extended service
contracts delivers the peace of mind that does just that.
Security+Plus vehicle protection plans can cover everything from over 1,100 vehicle components to roadside
assistance to rental vehicle costs and provide: Coverage
(at GT-R certified NISSAN dealers); utilizing: Genuine
NISSAN Parts (new or in some cases remanufactured);
installed by: Factory Trained Technicians (trained by
us to work on your GT-R). And you’ll be protected against
future inflation (rising cost of parts and labor).
Security+Plus coverage can be purchased any time
within your GT-R’s original 3-year/36,000-mile new vehicle basic limited warranty period. Just contact your
selling dealer and tell them you’d like to take advantage of
one of the best mechanical breakdown plans available for
your GT-R today.
* These products not available outside the United States.
Do you currently have someone that maintains your yard?
Cleans your house? Maintains your vehicle? With
Maintenance+Plus you’ll be hiring NISSAN to maintain
your GT-R to factory specification by factory trained technicians. Like Security+Plus, you’ll benefit from Coverage
at GT-R certified NISSAN dealers, Genuine NISSAN
Parts, Factory Trained Technicians, and you’ll be
protected against future inflation (rising costs of parts and
labor). What could be easier? A special
Maintenance+Plus plan has been specifically designed
for your GT-R. Didn’t purchase Maintenance+Plus at
the time of vehicle delivery? Don’t sweat the small stuff,
‘New’ Maintenance+Plus contracts can be purchased
any time within the first 36-months/7,500-miles of original
vehicle GTR sale date. If for some reason you missed this
initial window a ‘Used’ Maintenance+Plus contract
(that covers Oil and Filter changes) may be purchased at
anytime throughout the life of the your vehicle GT-R. Just
contact your selling dealer and tell them you’d like to take
advantage of one of the best maintenance plans available
for your GT-R today.
9
GENUINE NISSAN COLLISION PARTS
10
Your GT-R has been manufactured using a combination of
stamped steel, stamped aluminum, die-cast aluminum,
and carbon reinforced components and high precision
assembly jigs. If you have an accident, insist on Genuine
NISSAN Collision Parts. If you want your vehicle to be
restored using parts made to NISSAN’s original exacting
specifications – if you want it to last, help to protect your
personal safety and to help hold its resale value, the
solution is simple. Tell your insurance agent and your
repair shop to use only Genuine NISSAN Collision Parts.
As special skills, information and equipment are required
to correctly repair the body, be sure to contact your
NISSAN dealer or visit www.NissanUSA.com under
owner information to locate a GT-R certified body shop in
your area.
Many non-genuine parts are copies made from impressions of NISSAN parts and may not match the specifications and performance standards of Genuine NISSAN
Parts. As a result, non-genuine parts may not look or fit
right, and may be less safe.
See your participating GT-R certified NISSAN dealer for details.
* This warranty does not apply to vehicles or parts not distributed by Nissan North America and/or sold outside the United States.
The hood on your vehicle is a good example. NISSAN
designed it with hood buckling creases to help prevent the
hood from penetrating the interior of your vehicle in an
accident. Non-genuine parts may not provide such built-in
safeguards.
In some states, the law says you must be advised if
non-genuine parts are used to repair your vehicle. Why
should you take a chance?
Replacement Panel Limited Lifetime
Corrosion Warranty*
If you have your collision damage repaired using Genuine
NISSAN Outer Sheet Metal Panels you don’t have to
worry about corrosion. That’s because these panels are
warranted against inside out rust-through perforation for
as long as you own your NISSAN. Another reason to insist
on Genuine NISSAN Collision Repair Parts.
DETERMINING THE PROPER MAINTENANCE INTERVAL
Depending on your driving habits and local conditions, you should follow one of the two maintenance
schedules listed below for scheduled maintenance. In addition to Schedule 1 maintenance, additional
maintenance must be performed for optimum performance. Use these guidelines to determine which
maintenance schedule to use:
SCHEDULE 1 (Every 6,000 miles or 6
months, whichever comes first)
Schedule 1 features 6,000-mile service
intervals. Use Schedule 1 if you primarily operate your vehicle under any of these conditions:
● Repeated short trips of less than 5 miles in
normal temperatures or less than 10 miles in
freezing temperatures
● Stop-and-go traffic in hot weather or lowspeed driving for long distances
● Driving in dusty conditions or on rough,
muddy, or salt-spread roads
SCHEDULE 2 (Every 6,000 miles or 6
months, whichever comes first)
Schedule 2 features 6,000-mile service intervals; with Schedule 2 fewer maintenance items
are regularly checked or replaced than with
Schedule 1.
Generally, Schedule 2 applies only to highway
driving in temperate conditions. Use Schedule
2 only if you primarily operate your vehicle under conditions other than those listed in
Schedule 1.
11
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS
12
The following descriptions are provided to give you a better understanding of the scheduled maintenance
items that should be regularly
checked or replaced. The maintenance log indicates at which
mileage/time intervals each item requires service.
In addition to scheduled maintenance, your NISSAN requires that
some items be checked during normal day-to-day operation. You can
find these items listed under “General
Maintenance” in Chapter 8 of your
Owner’s Manual.
Maintenance items and intervals
marked with “*” are recommended by
NISSAN for reliable vehicle operation. You are not required to perform
such maintenance in order to maintain the emission warranty or manufacturer recall liability.
When applicable, additional information can be found in the “Maintenance
and do-it-yourself” section in Chapter
8 of your Owner’s Manual.
For recommended fuel, lubricants,
fluids, grease, and refrigerant, refer to
Chapter 9 in your Owner’s Manual.
Emission Control System
Maintenance:
Drive Belts*
Check engine drive belts for wear,
fraying or cracking. Replace any damaged drive belts.
Engine Air Filter
Replace at specified intervals. When
driving for prolonged periods in dusty
conditions, check/replace the filter
more frequently.
Engine Coolant*
Replace engine coolant at the specified interval.
Engine Oil and Oil Filter
Replace engine oil and oil filter at the
specified intervals. Check engine oil
level every 1,800 miles and add as
needed. For recommended oil grade
and viscosity refer to Chapter 9 in
your Owner’s Manual.
Engine Settings*
Balance the air flow for left and right
banks at specified intervals.
Engine Valve Clearance*
Inspect only if valve noise increases.
Adjust valve clearance if necessary.
Evaporative Emissions Control
Vapor Lines*
Check vapor lines and connections
for leaks or looseness. Tighten connections or replace parts as necessary.
Fuel Filter
Maintenance-free item.
Fuel Lines*
Check the fuel hoses, piping and
connections for leaks, looseness, or
deterioration. Tighten connections or
replace parts as necessary.
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS
Throttle Chamber Deposits*
Visually inspect the throttle chamber
for deposits and clean as necessary.
Spark Plugs
Replace at specified intervals. Install
new plugs of the same type as originally equipped.
Chassis and Body
Maintenance:
Brake Lines and Cables
Visually inspect for proper installation. Check for chafing, cracks, deterioration, and signs of leaking. Replace any deteriorated or damaged
parts immediately.
Brake Pads & Rotors
Check for wear, deterioration and
fluid leaks. Replace any deteriorated
or damaged parts immediately. Replace all four sets of brake pads and
disc rotors at the same time to maintain maximum brake performance.
Exhaust System
Visually inspect the exhaust pipes,
muffler and hangers for leaks, cracks,
deterioration, and damage. Tighten
connections or replace parts as necessary.
In-Cabin Microfilter
Replace at specified intervals. When
driving for prolonged periods in dusty
conditions, replace the filter more frequently.
Measurement and Adjustment
of Wheel Alignment
Manage the wheel alignment by measuring and adjusting at specified intervals.
Propeller Shaft(s)
Check for damage, looseness, and
grease leakage.
Steering Gear and Linkage, Axle
and Suspension Parts, Drive
Shaft Boots
Check for damage, looseness, and
leakage of oil or grease. Under severe
driving conditions, inspect more frequently.
Tire Rotation
Tires cannot be rotated as front tires
are different size from rear tires.
Transmission Oil, Differential
Oil
Replace fluid at specified intervals.
Visually inspect for signs of leakage at
specified intervals.
Transmission settings
To keep the best condition for transmission, this inspection allows learning of the clutch touch point and the
engaged gear position and neutral
position for each gear.
13
ADDITIONAL MAINTENANCE ITEMS
14
The information and specifications below apply
only when engaging in performance driving.
The following information applies only if you engage in
performance driving such as driving your GT-R for extended periods under the following conditions.
● Higher-RPM (approaching redline) operation
● Frequent high pedal force braking from moderate and
higher speeds
● Frequent throttle activation
● Fast revving throughout the RPM range
In such cases, the following additional maintenance
guidelines apply.
You should carefully read your NISSAN GT-R Warranty Information Booklet for important information concerning warranty coverage, limits, and exclusions.
We recommend that all GT-R maintenance be performed
at a GT-R certified NISSAN dealer. NISSAN will only pay
for NISSAN GT-R Performance Optimization Services
performed at a GT-R certified NISSAN dealer.
PRECAUTIONS ON PERFORMANCE DRIVING
Checking the temperature of the coolant and oils
on the multi function display
When the temperatures of the engine coolant and oil, and
the oil pressure exceed the normal range, the color of the
meter on the multi function display changes to red to warn
the driver. When engaging in high performance driving,
switch the display to the function meter to display the
temperature of the engine coolant and oil, and the oil
pressure. When the color of the meter display changes to
red, perform cool down driving. When the values of the
temperature and pressure return to the normal range, the
color of the meter display will turn back to white.
Warning temperature:
● Engine coolant temperature is 230°F (110°C) or
higher: If the engine coolant temperature increases
above 230°F (110°C), the color of the meter display on
the multi function display changes to red to warn of a
possible overheat condition and engine output is reduced.
● Engine oil temperature is 275°F (135°C) or higher: If
the engine oil temperature is higher than 275°F
(135°C), the meter display changes to red, maximum
engine speed is automatically limited to 4,000 rpm and
the transmission automatically changes from the ⬙M⬙
position to the ⬙A⬙ position.
ADDITIONAL MAINTENANCE ITEMS
● Transmission oil temperature is 284°F (140°C) or
higher: If the transmission oil temperature increases to
over 284°F (140°C), the color of the meter display
changes to red. However, the vehicle can continue to
be driven until the temperature reaches 295°F
(146°C). If the oil temperature exceeds 284°F (140°C)
while driving, (the color of the meter displayed in red),
change both the transmission oil and differential oil
after driving because these fluids have deteriorated
because of the heat.
Cool Down
Cool down the vehicle to help extend the life of the vehicle
if coolant temperatures are extremely high. Drive the vehicle at 37 to 50 MPH (60 to 80 km/h), in 5th or 6th gear
for 2 to 3 miles (3 to 5 km) and then stop the engine.
Refueling Precautions
WARNING: Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off automatically.
Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire. The fuel
tank is full at the first automatic shutoff.
To maximize vehicle performance, the fuel tank is located
as low as possible to lower the vehicle center of gravity.
The tank is also divided into two parts. This fuel tank
design causes higher pressures inside the tank than other
vehicles so fuel spillage is possible by trying to top off the
fuel tank after automatic shutoff.
The fuel tank pressure is higher when the vehicle is hot,
especially if the tank is more than half full. If the fuel cap is
opened when the vehicle is hot, it may cause fuel spray
and there may be a hissing noise. Open the cap slowly,
releasing the pressure from the tank gradually. Also if the
vehicle is refueled when the vehicle is hot, the fuel pump
may automatically shut off before the tank is full. This does
not indicate that there is a malfunction. Refuel slowly or
refuel after the vehicle has cooled.
INSPECTION AND ADJUSTMENTS BEFORE PERFORMANCE DRIVING
Fluids
* Check the engine, transmission, differential and under
the vehicle for oil and coolant leaks.
* Check the fluid levels and adjust as necessary using the
specified fluid as described under the conditions listed in
RECOMMENDED FLUIDS AND MAINTENANCE INTERVAL.
15
ADDITIONAL MAINTENANCE ITEMS
16
* NISSAN recommends to adjust the engine oil level
2
be 0.39 in (10 mm) (16 oz, 0.5L)
the engine oil dipstick. (
Before checking the oil level, run the engine until it
reaches operating temperature and wait at least 5 minutes
after turning off the engine. Make sure the oil level always
remains above the L mark.
When the vehicle is delivered, the engine oil is set to “H -
0.39 in (10 mm)” for optimal high performance driving.
* Some amount of oil is consumed by your engine under
normal operating conditions, and oil consumption by itself
does not necessarily indicate any malfunction. If your rate
of oil consumption increases suddenly or without explanation, NISSAN recommends that you have your vehicle
inspected by a GT-R certified NISSAN dealer.
3
range is 1.18 in (30 mm))
䊊
below the H mark on
䊊
1
䊊
to
and
䊊
5
on
䊊
5
䊊
6
* Adjust the power steering fluid level to the R mark
the power steering dipstick when the fluid temperature is
6
hot or
Fluid temperature:
Hot: 122 to 176°F (50 to 80°C): between
Cold: 32 to 86°F (0 to 30°C): between
Coolant Level and Mixture Ratio
Check the coolant level in the pressurized coolant reservoir. Adjust the level so that the fluid is between the MAX
and MIN markings. For the coolant, use Genuine NISSAN
Long Life Coolant. (On delivery of new vehicle, the reservoir is filled to the MIN level. Be sure to replenish approximately 3/8 US quart (0.3 to 0.4 liter) of coolant.)
when the fluid temperature is cold.
䊊
3
䊊
1
䊊
and
ADDITIONAL MAINTENANCE ITEMS
NOTICE: Do not overfill the coolant. This may increase the pressure in the cooling system and
cause coolant leaks.
To maximize vehicle performance, the coolant mixture ratio
should be a combination of 30% coolant/antifreeze and
70% demineralized or distilled water for maximum cooling
system performance regardless of ambient temperatures.
If ambient temperatures are anticipated below 5°F
(-15°C), make sure a proper mixture ratio of 50% antifreeze and 50% demineralized or distilled water mix is
used.
Engine and Powertrain
* Check the engine, transmission, differential and under
the vehicle for oil and coolant leaks.
* Inspect the areas surrounding the catalytic converter for
heat deterioration.
* Before engaging in performance driving, appropriate
clutch adjustment must be performed by your GT-R certified NISSAN dealer.
NOTICE: Failure to have the clutch properly adjusted before performance driving may cause the
transmission oil temperature to increase which
may cause transmission damage.
* Inspect and confirm the clearance between the exhaust
finisher and rear bumper is more than 0.24 in (6 mm)
(up/down) and more than 0.20 in (5 mm) (left/right).
* Inspect the dust boot of the drive shaft universal joint for
cracks or damage.
Suspension and Wheel Alignment
* Check the steering and suspension system and other
links for loose and/or damaged parts.
* Measure and adjust the wheel alignment. Contact a
GT-R certified NISSAN dealer to adjust the wheel alignment to the recommended setting for high performance
driving.
Preventing toe-out:
Toe-out can cause uneven tire wear or damage to areas
inside the tires due to high heat. Be sure to have the wheel
alignment toe-in setting checked and adjusted by your
GT-R certified NISSAN dealer before any performance
driving on closed circuit tracks. Obey all traffic laws when
on public roads.
Toe-in specification
Front: 0.059 in (1.5 mm)
Rear: 0.079 in (2.0 mm)
17
ADDITIONAL MAINTENANCE ITEMS
18
Wheels and Tires
* Check tire wear and cracking.
* Inspect the tire sidewall for damage.
* Check the tire pressure and adjust the pressure as
necessary when the tires are cold.
Adjust the tire pressure to the specification shown in the
table, in order to make the balance of rigidity between the
front and rear tires more uniform when the temperature of
the tires increases due to driving at high speed or engaging in high performance driving.
Condition Pressure PSI (kPa)
Starting to drive (Tires are cold) Front: 30.5 (210) - 31.9 (220)
Increasing tire pressure (Tires are
hot)
Rear: 29 (200)
Front: Not exceeding 39.2
(270)
Rear: Not exceeding 37.8 (260)
The tire pressure changes depending on the outside
temperature or altitude. Check the tire pressure regularly
and when the climate conditions change.
* The chart below indicates how the tire pressure will
decrease as outside air temperature decreases.
WARNING: Keep your tires inflated to the correct
tire pressure. Driving with low tire pressure can
damage some powertrain systems and affect the
operation of the ABS and VDC systems. Low tire
pressure may also cause tire failure and result in
serious personal injury or death.
* Make sure the tire valve stem cap is installed and that the
valve stem is tight. When installing the cap, make sure to
tighten the cap by hand. If a tool is used to tighten the cap,
the cap may be damaged.
* Make sure the wheel nuts are tight.
* Make sure the drive shaft nuts are tight.
ADDITIONAL MAINTENANCE ITEMS
* Make sure to replace the grommet seal, the valve core
and the valve cap of the Tire Pressure Monitoring System
(TPMS) sensor attached to the wheel every 3 years for
performance driving use. Replace them every 5 years
even when not engaging in performance driving. A dirty
grommet seal will cause the air leak from the tire.
* Make sure that the nuts and valves that are attached to
the TPMS sensor are tight and there is no nitrogen leak.
* Use only a NISSAN genuine valve cap or equivalent.
* Check wheel hub run out and that the wheel rotates
smoothly without any friction. Check these with the tires
removed whenever an inspection is performed with the
vehicle jacked up.
* Secure road wheel balance weights with aluminum tape.
* Check that the wheel nuts are not stripped.
* Make sure the tire has not slipped on the wheel causing
the assembly to be out of balance. The reference marks on
the tire and wheel should be aligned. If the reference
marks are not aligned, the tire has slipped on the wheel.
Have the wheels/tires rebalanced. Make sure the old
reference marks are erased and new reference marks are
applied to the wheel and tire. When installing new tires on
the wheels, make sure new reference marks are applied to
the wheels and tires.
Avoid the driving conditions listed under ⬙Additional maintenance items⬙ in this section for 48 hours after tires are
installed on the wheels. The tire may slip on the wheel if
the vehicle is driven in these conditions before 48 hours
have passed. If the tire slips on the wheel, the wheel/tire
assembly will be out of balance and will require rebalancing.
19
ADDITIONAL MAINTENANCE ITEMS
Brakes
* Check for the heat deterioration of the brakes and parts
around the brakes.
* It is recommended that you remove air from the brake
system after any of the following:
● When engaging in high performance driving for the first
time after purchasing a new vehicle.
● After replacing the brake fluid.
● When engaging in high performance driving for a sus-
tained period of time. It is recommended that bleeding
the brake be performed when the brake calipers are
hot (about 212°F (100°C)).
Brake Pad:
* NISSAN recommends adding an additional cross spring
to the front calipers before engaging in performance driving. The additional spring reduces brake pad movement
resulting from cornering forces and will reduce the stroke
of the brake pedal. Contact a GT-R certified NISSAN
dealer to purchase the spring and arrange installation. If a
cross spring is added, a clattering or squeaking sound
may be heard on rare occasions.
Brake Pad Break-in Procedure:
NISSAN recommends that a special brake pad break in
procedure be performed before engaging in performance
driving. Contact a GT-R certified NISSAN dealer for details.
INSPECTION AND ADJUSTMENTS AFTER PERFORMANCE DRIVING
NOTICE: At the completion of performance driving,
all fluid and other adjustments should be returned
to the normal fluid specifications.
Fluids
* Check the engine, transmission, differential and under
the vehicle for oil and coolant leaks.
* Check the fluid levels and adjust as necessary using the
specified fluid as described under the conditions listed in
RECOMMENDED FLUIDS AND MAINTENANCE INTERVAL on the following page.
* When changing fluids, be sure to use the specified fluids as
described in the RECOMMENDED FUELS/LUBRICANTS
Chart in the Technical and Consumer Information section of
your owner’s manual.
20
ADDITIONAL MAINTENANCE ITEMS
Recommended Fluids and Maintenance Interval
ITEMS Engine Oil
GT-R SPECIFIED FLUIDS Mobil 1 (0W-40)*1
● When the oil temperature stays below 230ºF (110ºC)
while driving
MAINTENANCE INTERVAL
ITEMS Transmission Oil
GT-R SPECIFIED FLUIDS Genuine NISSAN Transmission Oil R35 Special
MAINTENANCE INTERVAL
● When the oil temperature reaches between 230ºF
(110ºC) and 266ºF (130ºC) while driving
● When the oil temperature exceeds 266ºF (130ºC) while
driving
● When the oil temperature stays below 248ºF (120ºC)
while driving
● When the oil temperature reaches between 248ºF
(120ºC) and 284ºF (140ºC) while driving
● When the oil temperature exceeds 284ºF (140ºC) while
driving
Change engine oil and engine oil filter at the same
interval as Schedule 1 and 2.
Change engine oil and engine oil filter every 3,000
miles (5,000 km).
Change engine oil and engine oil filter immediately
after stopping.
Change transmission oil at the same interval as
Schedule 1 and 2.
Change transmission oil every 3,000 miles (5,000
km).
Change both transmission oil and differential oil immediately after stopping. Differential oil temperature usually increases concurrently.
21
22
ADDITIONAL MAINTENANCE ITEMS
ITEMS Differential Oil (front and rear)
GT-R SPECIFIED FLUIDS Differential Oil R35 COMPETITION type 2189E*2
● When the oil temperature stays below 248ºF (120ºC)
while driving
● When the oil temperature reaches between 248ºF
MAINTENANCE INTERVAL
ITEMS Brake Fluid
GT-R SPECIFIED FLUIDS Genuine NISSAN Brake Fluid R35 Special II*3
MAINTENANCE INTERVAL Change brake fluid every 3,000 miles (5,000 km).
*1: Mobil 1 (0W-40) (100% synthetic) is the factory fill oil. The VR38 engine with its plasma-sprayed bores was developed using this oil. NISSAN cannot ensure proper
engine operation and durability if other 0W-40 synthetic oil is used. If Mobil 1 (0W-40) is not available, Mobil 1 (10W-40) (100% synthetic) may be used; however,
some performance loss may be noticed.
*2 The differential oil temperature cannot be displayed on the multi function display. The differential oil temperature can be checked with the transmission oil temperature
since both usually increase or decrease concurrently.
*3: Genuine NISSAN Brake Fluid R35 Special II is the factory fill brake fluid. The Vehicle Dynamic Control (VDC) unit and other related parts were specially designed for
this brake fluid and NISSAN cannot ensure the best performance and proper operation of the vehicle if other brake fluid is used.
(120ºC) and 284ºF (140ºC) while driving
● When the oil temperature exceeds 284ºF (140ºC) while
driving
Change differential oil at the same interval as Schedule 1 and 2.
Change differential oil every 3,000 miles (5,000 km).
Change both transmission oil and differential oil immediately after stopping. Differential oil temperature
usually increases concurrently as the transmission oil
temperature.
ADDITIONAL MAINTENANCE ITEMS
Suspension and Wheel Alignment
* Check the steering and suspension system and other
links for loose and/or damaged parts.
* Measure and adjust the wheel alignment. Contact a
GT-R certified NISSAN dealer to adjust the wheel alignment to the recommended setting for normal driving.
Wheels and Tires
* Check tire wear and cracking.
* Inspect the tire sidewall for damage.
* Check the tire pressure and adjust the pressure as
necessary when the tires are cold. (See previous page’s
charts)
* Check that the wheel nuts are not stripped. Check if
there is no deformation on the contact surface of the
wheel nuts.
* Make sure the wheel nuts are tight.
* Make sure the drive shaft nuts are tight.
* Check wheel hub run out and that the wheel rotates
smoothly without any friction. Check these with the tires
removed whenever an inspection is performed with the
vehicle jacked up.
* Make sure the tire has not slipped on the wheel causing
the assembly to be out of balance. The reference marks on
the tire and wheel should be aligned. If the reference
marks are not aligned, the tire has slipped on the wheel.
Have the wheels/tires rebalanced. Make sure the old
reference marks are erased and new reference marks are
applied to the wheel and tire. When installing new tires on
wheels, make sure new reference marks are applied to the
wheels and tires.
* Make sure that the TPMS sensor installation nut and the
sensor valve are tight and there is no nitrogen leak.
Brakes
* Check for the heat deterioration of the brakes and parts
around the brakes.
* Check the condition of the brake pads and disc rotors
and replace them as necessary.
23
Loading...