Ninja BL68X, BL682UKCO Owner's Manual

Download

Page 1

BL68X Series

OWNER’S GUIDE

1-877-646-5288

Page 2

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE

USING YOUR NUTRI NINJA

NINJA® BLENDER SYSTEM WITH AUTO-IQ® TECHNOLOGY.

WARNING: Extension cords are not

recommended for use with this product.

WARNING: The blades are not afﬁxed to

the unit. They are removable and very sharp. Handle with care!

CAUTION: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

IMPOR TANT: This appliance is not intended

for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children shall not use or play with this appliance. Close supervision is necessary to keep appliance and cord out of reach of children during use.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. CAUTION: The blades are not afﬁxed to

the unit. They are removable and extremely sharp. When handling the stacked blades or the chopping blades, do not hold the blades but rather always hold the shaft. Blades are sharp. Handle carefully!

CAUTION: DO NOT BLEND HOT LIQUIDS.

Allow the liquids and foods to cool to room temperature before blending.

3. CAUTION: Do not blend dry ingredients

unless pulsing for short intervals per the instructions. Continuous blending dry ingredients will overheat the blender.

4. To protect against electrical shock, do not submerge the appliance or allow the power cord to come into contact with water or any otherliquid.

5. DO NOT allow young children to operate the appliance or use as a toy. Close supervision is necessary when any appliance is used near children.

6. Never leave an appliance unattended when in use.

7. Turn the appliance off and remove the power cord from the electrical outlet when not in use, before assembling or disassembling parts, accessing parts that move while in use and before cleaning. To unplug, grasp the plug and pull from the electrical outlet. Never pull from the power cord.

8. DO NOT abuse the power cord. Never carry the appliance by the power cord or yank it to disconnect from electrical outlet; instead, grasp the plug and pull to disconnect.

9. DO NOT use with damaged cord or plug.

10. DO NOT USE if the appliance is not working, has been dropped, dropped into water, damaged or left outdoors.

1-877-646-5288

Page 3

11. NO SERVICEABLE PARTS. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons when the appliance is used. Contact Customer Service.

12. Always use the appliance on a dry, level surface.

13. Keep hands, hair, clothing, as well as utensils out of container while processing or blending to reduce the risk of severe injury to persons or damage to the appliance. A scraper may be used but only when the appliance is not running.

14. Avoid contact with moving parts.

15. DO NOT attempt to sharpen blades.

16. DO NOT use the appliance if either set of blades are bent or damaged.

17. To reduce the risk of injury, never assemble the stacked blades in the pitcher or the chopping blade in the bowl without the pitcher or the bowl properly attached to the motor base.

18. DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a heated oven).

19. The use of attachments or accessories including canning jars, not recommended by the manufacturer may result in ﬁre, electric shock or personal injury.

20. DO NOT remove any container from the motor base while the appliance is in operation. Always unplug the unit when not in use.

21. To reduce the risk of injury, NEVER operate the appliance without the lid in place; DO NOT try to defeat or bypass the interlock mechanism. When using the removable blades, make sure they are properly installed before operating the appliance.

22. DO NOT expose containers to extreme temperature changes.

23. Extreme caution must be used when moving an appliance containing hot food, water or other liquids.

24. DO NOT overﬁll. DO NOT exceed “MAX” ﬁll line.

25. DO NOT operate the appliance empty.

26. To reduce the risk of burns, always allow the appliance to cool before taking off parts and before cleaning.

27. Max ON time is 60 seconds under 1500W load. If the appliance overheats, a thermal switch will become activated and shut off the motor. To reset, unplug the appliance and let it cool down for approximately 15 minutes before using again.

28. In the event that the unit overloads, the control panel lights will ﬂash and the unit will shut down. Unplug the appliance and let it cool down for approximately 15 minutes before using again.

29. Max PULSE iteration is 30 Pulses. After 30 Pulses allow 10 minutes to pass before running the PULSE function up to an additional 30 Pulses.

30. The maximum rating is based on the stacked blade (pitcher) that drives the greatest power and other recommended attachments may draw signiﬁcantly less power or current.

31. To avoid injury, never attempt to place the Pro Extractor Blade assembling the blade assembly to the Nutri Ninja® Cup.

32. DO NOT push food into the food chute with your ﬁngers. Always use the food pusher provided.

33. Appliance accessories are not intended to be used in the microwave as it may result in damage to the accessories

34. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use this appliance for anything other than its intended use. Do not use outdoors.

35. DO NOT remove lid until blade has COMPLETELY STOPPED.

36. DO NOT attempt operation without the cover being in place.

37. DO NOT process liquid ingredients in the coffee grinder. Accessory is not intended for liquid processing.

38. DO NOT attempt to chop ice in the coffee grinder.

39. Check stainless steel cup and coffee grinder for presence of foreign objects before using.

™

onto the motor base without ﬁrst

SAVE THESE

INSTRUCTIONS

Page 4

This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and electronic equipment (WEEE).

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return your used device, please use the return and collection systems or contact the retailer where this product was purchased. They can take this product for environmental safe recycling.

This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC and its revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.

THIS BOOK COVERS MODEL NUMBERS:

BL68X***** 30

TECHNICAL SPECIFICATIONS Voltage: 220-240V~, 50/60Hz. Power: 1500W

Pitcher Capacity: 2.1 L Max Liquid: 2 L

Bowl Capacity: 1.8 L

XL Multi-Serve Ninja Jar Capacity: 1.4 L

Nutri Ninja Cup Capacity: 300ml 500ml 650ml 900ml

Stainless Steel Ninja

Coffee and Spice Ninja Grinder: 10 tbsp

Cup Capacity: 650ml

1-877-646-5288

Page 5

Contents

Thank you for purchasing the Nutri Ninja Ninja

Blender

System with Auto-iQ® Technology.

Getting to Know Your Nutri Ninja | Ninja Blender System with Auto-iQ Technology ............... 5

Using the Nutri Ninja | Ninja Blender System with Auto-iQ Technology . ..............................7

Assembly and Use for the Blender .......................................................................... 8

Assembly and Use for the Food Processor ............................................................10

Assembly and Use for the Cutting Discs ................................................................ 12

Assembly and Use for the Mini Prep Bowl ............................................................. 13

Assembly and Use for the Nutri Ninja .................................................................... 14

Use of the Coffee and Spice Ninja Grinder .............................................................15

Programs, Speed Settings, & Uses for the Blender Pitcher ..............................................16

Programs, Speed Settings, & Uses for the Nutri Ninja Cups ............................................. 16

Programs, Speed Settings, & Uses for the Food Processor ..............................................17

Speed Setting & Uses for the Coffee and Spice Ninja Grinder .......................................... 17

Care & Maintenance ....................................................................................................18

Troubleshooting Guide ..................................................................................................19

Page 6

BLEND

BLAST

FROZEN DRINKS

SMOOTHIES

FOOD PUREE

NutriNinja

PULSE

HIGH

MED

ON OFF

1500 WATTS

LOW

UTO

BLEND

UTO

BLAST

FROZEN DRINKS

SMOOTHIES

FOOD PUREE

NutriNinja

PULSE

HIGH

MED

OFF

1500 WATTS

LOW

UTO

BLEND

UTO

BLAST

FROZEN DRINKS

SMOOTHIES

FOOD PUREE

NutriNinja

PULSE

HIGH

MED

ON OFF

1500 WATTS

LOW

UTO

BLEND

UTO

BLAST

FROZEN DRINKS

SMOOTHIES

FOOD PUREE

NutriNinja

PULSE

HIGH

MED

ON OFF

1500 WATTS

LOW

UTO

BLEND

UTO

BLAST

FROZEN DRINKS

SMOOTHIES

FOOD PUREE

NutriNinja

PULSE

HIGH

MED

ON OFF

1500 WATTS

LOW

UTO

BLEND

UTO

BLAST

Getting To Know Your Nutri Ninja® | Ninja® Blender System with Auto-iQ® Technology

g h k

a 900 ml Nutri Ninja Cup b 650 ml Nutri Ninja Cup c 500 ml Nutri Ninja Cup d 300 ml Nutri Ninja Cup e 650 ml Stainless Steel Ninja Cup f XL Multi-Serve 1.4 L Ninja Jar g Pro Extractor Blades h Sip & Seal® Lid i Spout Lid

1-877-646-5288

j Shaker Lid k Silicone Grip Sleeve l Coffee and Spice Ninja Grinder m Food Processor Lid

™

n Food Processor Bowl o Chopping Blade (food processor) p Dough Blade (food processor) q Feed Chute Lid r Mini Prep Bowl

s Slicing/Shredding Disc

(food processor)

t Grating Disc (food processor) u Spindle for Discs & Mini Prep Bowl v Mini Prep Bowl Blade w Blender Pitcher x Blender Lid with locking handle y Stacked Blades (blender) z Motor Base

NOTE: Blades are not interchangeable.

Page 7

The Nutri Ninja® | Ninja® Blender System with Auto-iQ® Technology is a high powered innovative tool with a sleek design and outstanding performance, a true asset to any kitchen. The Nutri Ninja | Ninja Blender System with Auto-iQ Technology features intelligent programs that combine pulsing, blending and pausing patterns that do the work for you! Get great results every time with no guesswork required! For best results, be sure to carefully read all the instructions contained in the manual before using this appliance.

Nutri Ninja | Ninja Blender System with Auto-iQ Technology Features:

• PatentPendingNinjaBladeTechnology

• BPAFreeBlenderPitcher(maximumliquidcapacity2L),NutriNinjaCups,FoodProcessorBowlandLids

• Drip-FreePourSpout

• TotalCrushing

• LEDControlPanelwithTimer

• Sturdy,Non-SlipBase

• SmartLidtechnologyforeasyrelease

• 3speeds:Low/ Dough,Medium,&High

• 5Auto-iQsettings-Auto-iQFrozenDrinks/Smoothies,Auto-iQFoodPuree,NutriNinjaAuto-iQBlend,

Nutri Ninja Auto-iQ Ultra Blend and Auto-iQ Pulse

• NutriNinjaNutrient&VitaminExtraction

• XLMulti-serve1.4LNinjaJar,BPAfree

• StainlessSteel650mlNinjaCup,BPAfree

• CoffeeandSpiceNinjaGrinder,BPAfreelid

Technology

Page 8

Using the Nutri Ninja® | Ninja® Blender System with Auto-iQ® Technology

PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN USING THE APPLIANCE:

WARNING: Never leave the appliance

unattended while in use.

CAUTION: DO NOT BLEND HOT LIQUIDS.

Allow liquids and foods to cool to room temperature before blending.

CAUTION: Blade assemblies are sharp! Use

extreme caution when handling the blade assemblies. Always hold them by the shaft.

CAUTION: Never remove the container while

the appliance is still running.

CAUTION: We do not recommend grinding in

any of our Nutri Ninja Cups.

IMPORTANT: Never add ingredients into the

container before placing the blade in ﬁrst.

IMPORTANT: Blade assemblies are not

interchangeable.

IMPORTANT: DO NOT attempt to operate the

appliance without the lid on.

IMPORTANT: Never run the appliance empty.

IMPORTANT: Appliance accessories are not

intended to be used in the microwave as it may result in damage to the accessories.

CAUTION:

Stacked Blades are not locked in place. If using the pour spout, ensure that the lid is fully locked onto the blender pitcher.

CAUTION: Stacked

Blades are not locked in place. If pouring with the lid removed, ALWAYS remove the blade assembly ﬁrst before pouring.

CAUTION: Blade assemblies are sharp, not locked

in place and removable, handle with care. When handling the blade assemblies, always hold them by the shaf t.

BEFORE FIRST USE

1 Remove all packaging material and labels from the

appliance.

2 Wash the

CAUTION: Handle the blade assemblies with care

3 Rinse and dry thoroughly.

NOTE: The Stainless Steel Ninja Cup is NOT

4 The lids, pitcher, bowl, Nutri Ninja cups, discs, feed

5 Wipe the motor base clean with a damp cloth.

lids, pitcher, bowl, Nutri Ninja cups, discs, feed chute, jar, grinder and blade assemblies soapy water with a soft cloth.

when washing as the blades are very sharp.

dishwasher safe.

chute, jar, grinder and blade assemblies are all dishwasher safe. It is recommended that the lids and blades be placed on the top rack. Ensure that the blades are removed from the containers before placing in the dishwasher.

in warm,

1-877-646-5288

Page 9

Assembly and Use for the Blender

HIGH

PULSE

LOW

DOUGH

SMOOTHIE

SINGLE SERVE

PUREE

FROZEN

BLENDING

WARNING: Never leave the appliance unattended while in use.

CAUTION: Stacked Blades are sharp, not locked in place and removable, handle with care. When handling

the Stacked Blades, always hold them by the shaft.

IMPORTANT: Make sure that the motor base is plugged in for use.

ASSEMBLY

Fig. 1

LOW / DOUGH

MED

Fig. 4a Fig. 4b

1 Holding the Stacked Blade Assembly by the top of the

shaft, place it onto the drive gear inside the pitcher. Ensure that the attachment is seated properly and is standing upright. (Fig. 1)

NOTE: The blade will ﬁt loosely on the drive gear.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top.

3 Align and lower the Pitcher onto the motor base.

(Fig. 2) Handle should be aligned slightly to the right of the “LOCK” symbol on the motor base.

4 Rotate the pitcher clockwise until it locks in place, you

will hear a click when the lock is engaged. (Fig. 3)

5 The pitcher can be placed on the motor base two ways;

the handle can be on the front right corner or the front left corner. (Fig. 4a, Fig. 4b)

6 Add the ingredients to the pitcher, making sure that

they do not exceed the highest measured marking line on the side of the pitcher.

Fig. 2

Fig. 3

Fig. 5a

NOTE: When blending any kind of liquids, such as

mixtures of any drinks or smoothies, do not exceed the “MAX LIQUID” mark (2 L) on the pitcher.

NOTE: If you need to add additional ingredients while

the appliance is processing, open the pour spout cap and pour the ingredients in through the opening.

7 Holding the lid by the handle in the upright position, place

it on top of the pitcher aligning the triangle ( ) located on the lid with the triangle ( ) located on the pitcher’s handle. (Fig. 5a) Press the handle down until you hear a click. The triangles on the lid and the blender handle MUST be aligned in order for the blender to turn on. ( Fig. 5b)

8 Plug the power cord into the electrical outlet and press

the power button ( ).

IMPORTANT: As a safety feature, the power light

(

) will ﬂash and the motor will not work if the pitcher and lid are not installed correctly. When the pitcher and lid are installed properly, the power light ( ) will be solid, indicating that the appliance is ready for use.

Fig. 5b

Page 10

Assembly and Use for the Blender - cont.

WARNING: Never leave the appliance unattended while in use.

CAUTION: Stacked Blades are sharp, not locked in place and removable, handle with care. When handling

the Stacked Blades, always hold them by the shaft.

IMPORTANT: Make sure that the motor base is plugged in for use.

Fig. 6

USE REMOVAL

Fig. 8

NOTE: Nutri Ninja® | Ninja® Blender System with Auto-

iQ® Technology can sense which jar is on the motor base. The function lights will illuminate depending on which jar is placed on the motor base. (Fig. 6)

9 Press the power button to turn on the unit. Select

the speed or Auto-iQ program that best suits your needs. The Auto-iQ program will stop the appliance automatically at the end of the program. (Fig. 7)

NOTE: Pulse ingredients for even chopping by holding

the Auto-iQ Pulse button until your desired consistency is reached.

NOTE: Max PULSE iteration is 30 Pulses. After 30

Pulses allow 10 minutes to pass before running the PULSE function up to an additional 30 Pulses.

10 To pause the appliance, press the selected speed or

Auto-iQ Program a second time. (Fig. 8)

11 When you have reached your desired consistency, stop

the appliance by pressing the power button ( ) and wait for the blade to stop turning. (Fig. 8)

12 Turn the pitcher anticlockwise to remove and then lift

off the base. (Fig. 9)

1-877-646-5288

Fig. 9Fig. 7

CAUTION: Never insert your hands in the pitcher

as the Stacked Blades are sharp. Always use a spatula to dislodge food that has stuck to the sides of the pitcher.

CAUTION: If using the pour spout, ensure that the

lid is fully locked onto the blender pitcher.

CAUTION: If pouring with the lid removed, ALWAYS

remove the blade assembly ﬁrst before pouring.

13 Depending on the consistency of the contents in the

container, open the pour spout cap and use the spout to empty liquid contents.

14 For thicker consistencies, remove the lid and blade

attachment carefully (by its shaft), then empty contents from the container. To remove the lid, press the release button on the lid and pull the lid handle up to a 90° angle and lift the lid off the blender pitcher. (Fig. 10)

15 Make sure that the unit is unplugged when not in use.

16 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base and gently pull the unit up and towards you. ( Fi g. 11)

Fig. 10 Fi g. 11

Page 11

Assembly and Use for the Processor Bowl

MED

LOW /

DOUGH

WARNING: Never leave the appliance unattended while in use.

CAUTION: Chopping Blade is sharp, not locked in place and removable, handle with care. When handling

the Chopping Blade, always hold by the shaft.

IMPORTANT: Make sure that the motor base is plugged in for use.

ASSEMBLY

Fig. 1

LOW /

DOUGH

MED

Fig. 5a Fig. 5b

NOTE: Nutri Ninja® | Ninja® Blender System with

Auto-iQ® Technology can sense which jar is on the motor base. The function lights will illuminate depending on which jar is placed on the motor base. ( Fig. 1)

1 Holding the desired blade by the top of the shaft, place it onto

the drive gear inside the bowl. Ensure that the attachment is seated properly and is standing upright. (Fig. 2)

NOTE: The blade will ﬁt loosely on the drive gear.

2 Place the motor base on a clean, dry, level surface such

as a counter or table top. Press down on the motor base to make sure that the suction cups adhere to the counter or table top.

3 Align and lower the Processor Bowl onto the motor

base. (Fig. 3) Handle should be aligned slightly to the right of the “LOCK” symbol on the motor base.

4 Rotate the bowl clockwise until it locks in place, you will

hear a click when the lock is engaged. (Fig. 4)

5 The bowl can be placed on the motor base two ways;

the handle can be on the front right corner or the front left corner. (Fig. 5a, Fig. 5b)

Fig. 2

Fig. 3

Fig. 4

Fig. 6b

Fig. 6a

6 Add the ingredients to the bowl, making sure that they

do not exceed the “MAX” ﬁll line on the side of the bowl.

7 Holding the lid by the handle in the upright position,

place it on top of the Processor Bowl aligning the triangle ( ) located on the lid with the triangle ( ) located on the Processor Bowl handle. (Fig. 6a) Press the handle down until you hear a click. The triangles on the lid and the Processor Bowl handle MUST be aligned in order for the blender to turn on. (Fig. 6b)

NOTE: The 1.8 L bowl is not intended for blending

drinks. Do not overﬁll.

8 Plug the power cord into the electrical outlet and press

the power button (

IMPORTANT: As a safety feature, the power

button (

) will ﬂash and the motor will not work if the bowl and lid are not installed correctly. When the bowl and lid are installed properly, the power but ton ( ) will be solid, indicating that the appliance is ready for use.

Page 12

Assembly and Use for the Processor Bowl - cont.

WARNING: Never leave the appliance unattended while in use.

CAUTION: Chopping Blade is sharp, not locked in place and removable, handle with care. When handling

the Chopping Blade, always hold by the shaft.

USE

Fig. 1

Fig. 2 Fig. 3 Fig. 4

REMOVAL

USING THE CHOPPING BLADE

1 Holding the Chopping Blade by the shaft, place it

onto the gear shaft inside the bowl. Ensure that the attachment ﬁts around the gear shaft and that it is standing straight.

2 Add the ingredients and secure the bowl lid onto the

bowl. (Fig. 1)

3 Plug the power cord into the electrical outlet and press

on the power button ( program that best suits your needs. Pulse ingredients for even chopping by holding the Auto-iQ Pulse button until your desired consistency is reached.

NOTE: Max PULSE iteration is 30 Pulses. After 30

Pulses allow 10 minutes to pass before running the PULSE function up to an additional 30 Pulses.

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

4 When you have reached your desired consistency, stop

the appliance by pressing the power button ( wait for the blade to stop turning. (Fig. 2)

5 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 2)

6 Turn the bowl anticlockwise and lift it to remove it from

the motor base. (Fig. 3)

CAUTION: If pouring from the bowl, ALWAYS

remove the blade assembly ﬁrst before pouring.

7 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base and gently pull the unit up and towards you. (Fig. 4)

). Select the speed or Auto-iQ®

) and

USE

Fig. 5

USING THE DOUGH BLADE

1 Holding the dough blade by the shaft, place it onto the

gear shaft inside the bowl. Ensure that the attachment ﬁts around the gear shaft and that it is standing straight.

(Fig. 5)

2 Add the ingredients and secure the bowl lid onto the bowl. 3 Plug the power cord into the electrical outlet and press

on the power button ( control panel and process until ingredients come together to form a mass.

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

4 Once ﬁnished making dough, stop the appliance by

pressing the power button ( stop turning.

5 To remove the lid, press the release button on the lid

and pull the lid handle up to a 90° angle. (Fig. 2)

6 Turn the bowl anticlockwise and lift it to remove it from

the motor base. (Fig. 3)

7 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base and gently pull the unit up and towards you.

(Fig. 4)

). Select LOW/DOUGH on the

) and wait for the blade to

1-877-646-5288

Page 13

Assembly and Use for the Cutting Discs

WARNING: Never leave the appliance unattended while in use.

CAUTION: Use caution when handling the cutting discs as they are very sharp.

IMPORTANT: Use only the LOW/DOUGH setting when using either disc.

USING THE DISCS

NOTE: Cutting Discs must be used with the feed

chute lid.

1 Place the motor base on a clean, dry, level surface such

as a counter or table top. (Fig. 1) 2 Secure the bowl onto the motor base. 3 Place the spindle inside the bowl. 4 Use the ﬁnger holes to grasp the selected disc and

place it over the spindle. 5 Place the feed chute lid on the bowl and turn clockwise

until you hear a click indicating the lid is locked in

place. (Fi g. 1) 6 Plug the power cord into the electrical outlet and press

up on the power toggle ( 7 Select LOW/DOUGH on the control panel. The discs will

begin spinning. 8 Add the food that you want to slice, shred or grate

through the feed chute on the lid. (Fig. 1) Use the

two-part food pusher to help guide the food through

the feed chute. The middle piece of the food pusher is

removable to use for smaller ingredients. 9 When ﬁnished,stop the appliance by pressing the power

button (

) and wait for the disc to stop turning. Press the button on the feed chute lid located near the handle to unlock and turn the lid anticlockwise. Lift to remove from the processor bowl. Using the ﬁnger holes, carefully lift the disc out of the bowl and remove the spindle.

10 To release the motor base from the counter or table top,

place your hands underneath both sides of the motor base and gently pull the unit up and towards you.

) to turn the power “On”.

Fig. 1

Page 14

Assembly and Use for the Mini Prep Bowl

WARNING: Never leave the appliance unattended while in use.

CAUTION: Mini Prep Bowl Blade is sharp, not locked in place and removable, handle with care. When

handling the Mini Prep Bowl Blade, always hold by the shaft.

ASSEMBLY

USE

REMOVAL

Fig. 1

Fig. 3

Fig. 2

Fig. 4

USING THE MINI PREP BOWL

NOTE: The mini prep bowl must be used with the

ﬂat food processor lid.

1 Place the 1.8 L bowl onto the motor base.

2 Holding the spindle by the shaft, place it onto the gear

shaft inside the 1.8 L bowl. Ensure that the attachment ﬁts around the gear shaft and that it is standing straight. (F ig. 1)

3 Place the mini prep bowl aligning the spindle inside the

centre post. (Fig. 2)

4 Hold the Mini Prep Bowl Blade by the shaft and carefully

place it over the centre post of the mini prep bowl. (Fig. 3)

5 Add ingredients into the mini prep bowl.

6 Holding the lid by the handle in the upright position,

place it on top of the 1.8 L bowl aligning the arrow ( located on the lid with the arrow ( ) located on the bowl’s handle. (Fig. 4) Press the handle down until you hear a click.

Fig. 6

Fig. 5

7 Plug the power cord into the electrical outlet and press

on the power button (

8 Select the speed that best suits your needs. For best

results, hold the Auto-iQ® Pulse button down until you have reached your desired consistency. (Fig. 5)

NOTE: Max PULSE iteration is 30 Pulses. After 30

Pulses allow 10 minutes to pass before running the PULSE function up to an additional 30 Pulses.

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

When you have reached your desired consistency, stop the appliance by pressing the power button ( ) and wait for the Mini Prep Bowl Blade to stop turning

10 To remove the lid, pull the lid handle up to a 90° angle

and lift the lid off. (Fig. 6)

11 Carefully hold the Mini Prep Bowl Blade by the shaft and

)

lift it out of the mini prep bowl. (Fig. 7)

12 Turn the bowl anticlockwise and then lift off the base.

CAUTION: If pouring from the bowl, ALWAYS remove

the Mini Prep Bowl Blade ﬁrst before pouring.

Fig. 7

1-877-646-5288

Page 15

Assembly and Use for the Nutri Ninja

WARNING: Never leave the appliance unattended while in use.

CAUTION: Pro Extractor Blades™ are sharp and removable, handle with care. When handling the Pro

Extractor Blades, do not hold the blades, always hold by the base of the Pro Extractor Blades.

CAUTION: DO NOT BLEND HOT LIQUIDS. Allow the liquids and foods to cool to room temperature before blending.

IMPORTANT: Make sure that the motor base is plugged in for use.

Fig. 1

ASSEMBLY USE REMOVAL

or or

Fig. 2

IMPORTANT: When processing soft dry ingredients

Fig. 3 Fig. 4 Fig. 5 Fig. 6

such as day-old bread or cheese use quick, short 1 second pulses. Do not overﬁll to avoid overheating the appliance. Allow the appliance to cool after each use.

NOTE: Nutri Ninja | Ninja® Blender System with Auto-

Technology can sense which jar is on the motor base. The function lights will illuminate depending on which jar is placed on the motor base. (Fig. 1)

1 Place the motor base on a clean, dry, level surface such as a

counter or table top. Press down on the motor base to make sure that the suction cups adhere to the counter or table top.

2 Add ingredients to the Nutri Ninja cup.

3 Place the Pro Extractor Blades onto the cup and tightly

screw it on clockwise until you have a good seal. (Fig. 2)

4 Turn the Nutri Ninja cup upside down and place it onto the

motor base, aligning the tabs on the cup with the motor base. Rotate the Nutri Ninja cup clockwise until it locks in place, you will hear a click when the lock is engaged. (Fig. 3)

5 Press the power button on, and select the speed or

Auto-iQ program that suits your needs. The Auto-iQ program will stop the appliance automatically at the end of the program. (Fig. 4)

6. To pause the appliance, press the selected speed or Auto-iQ Program a second time.

7 Once you have reached your desired consistency, turn the

power button off. Turn the Nutri Ninja cup anticlockwise and pull straight up to remove. (Fig. 5, Fig. 6)

NOTE: Do not over ﬁll! To avoid spilling, do not add

ingredients past the “MA X” ﬁll line.

8 Turn the cup upright and remove the Pro Extractor

Blades by twisting the blade assembly anticlockwise.

9 Place the Sip & Seal® lid onto the Nutri Ninja cup, twist

to seal and enjoy!

NOTE: Sip & Seal lid not intended for use with the XL

Multi-serve 1.4 L Ninja Jar.

10 Make sure that the motor base

is unplugged when not in use.

11 To release the motor base

from the counter or table top, place your hands underneath both sides of the motor base and gently pull the unit up and

Fig. 7

towards you. (Fig. 7)

Page 16

Use of the Coffee and Spice Ninja® Grinder

WARNING: Never leave the appliance unattended while in use.

CAUTION: Handle the blade assembly of the stainless steel grinding cup with care as the blades are very sharp.

WARNING: Do not process liquid ingredients. The grinder accessory is not intended for liquid processing.

Do not attempt to chop ice.

CAUTION: Check the grinding cup for presence of foreign objects before using.

ASSEMBLY USE REMOVAL

Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5

1 Place the motor base on a clean, dry, level surface such

as a counter or table top. Press down on the motor base to make sure that the suction cups adhere to the counter or table top.

2 Make sure that the motor base is plugged in for use.

Lights will not yet illuminate.

3 Add ingredients to the stainless steel grinding cup. Use

the measurement lines on the grinding cup for added convenience!

NOTE: Do not overﬁll! to avoid spilling, do not add

ingredients past the “MA X” ﬁll line.

4 Place the lid onto the blade assembly with stainless

steel grinding cup so that the tabs on the cup meet the entry point on the blade assembly. Twist until the lid is locked in place. ( Fig. 1)

5 Place the grinder onto the motor base, aligning the tabs

on the grinder with the motor base. Turn it clockwise, until you feel it click into place. (Fig. 2)

1-877-646-5288

6 Use only HIGH setting in short intervals until you reach

your desired consistency.

7 To remove the grinder, ensure that the motor has

stopped running. Do not remove cover until blade has completely stopped. Then turn the grinder anticlockwise (Fig. 4) and pull straight up to remove.

(Fig. 5)

8 Remove the blade assembly with stainless steel

grinding cup by twisting the lid anticlockwise. Be sure to store the grinder with the lid attached.

10 Make sure that the motor base is unplugged when not

in use.

11 To release the motor base

from the counter or table top, place your hands underneath both sides of the motor base and gently pull the unit up and towards you. (Fig. 6)

(Fig. 3)

Fig. 6

Page 17

Speed Setting & Uses for the Blender

FUNCTION CONTAINER

Frozen Drinks /

Ice Crush

Blender Pitcher Stacked Blade

BLADE

TYPE

Pureeing Blender Pitcher Stacked Blade Auto-iQ Food Puree

Speed Setting & Uses for the Nutri Ninja® Cup

FUNCTION CONTAINER

Nutri Ninja

XL Multi-serve

Smoothies

Green Smoothies

Grating Nutri Ninja Cup

Chopping Nutri Ninja Cup

1.4 L Ninja Jar

Stainless Steel

Ninja® Cup

Nutri Ninja Cup XL Multi-serve

1.4 L Ninja Jar

Stainless Steel

Ninja Cup

Cup

BLADE

TYPE

Pro Extractor

™

Blades

Pro Extractor

™

Blades

Pro Extractor

™

Blades

Pro Extractor

™

Blades

SPEED or PROGRAM TYPE OF FOOD

Auto-iQ® Frozen Drinks/

Smoothies

Ice

Frozen Drinks

Smoothies

Soups

Milkshakes

SPEED or PROGRAM TYPE OF FOOD

Smoothies

Nutri Ninja Auto-iQ Blend

Nutri Ninja Auto-iQ Ultra

Blend

Auto-iQ Pulse

Nutri Ninja Auto-iQ Blend

High

Auto-iQ Pulse

Nutri Ninja Auto-iQ Blend

High

Frappes

Milkshakes

Protein Drinks

Frozen Fruits

Frozen Vegetables

Kale

Celery

Spinach

Seeds

Ice

Grated Cheese Bread Crumbs

Salsa

Vegetables

Nuts

Page 18

Speed Setting & Uses for the Food Processor

FUNCTION CONTAINER

Mincing

Kneading and Dough Mixing

Processing

Emulsifying

Grinding

Grating

Chopping

Batters

Slicing/

Shredding

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

Food Processor

Bowl

BLADE

TYPE

Chopping

Blade

Dough Blade Low/Dough

Chopping

Blade

Chopping

Blade

Chopping

Blade

Chopping

Blade

Grating Disc

Chopping

Blade

Dough Blade Low/Dough

Reversible

Slicing

Shredding

Disc

SPEED or PROGRAM TYPE OF FOOD

Auto-iQ® Pulse

Auto-iQ Food Puree

Low/Dough

Medium

High

Low/Dough

Medium

Medium Meat

Auto-iQ Pulse

Low/Dough (when using

Disc)

Auto-iQ Pulse

Low/Dough

Onion Garlic Herbs

Bread Dough

Pie Dough

Pizza Dough Pretzel Dough Cookie Dough

Pâtés

Stewed Fruits

Dips

Apple Sauce

Spreads

Baby Food

Salad Dressings

Dips

Sauces

Grated Cheese Bread Crumbs

Spices

Salsa

Vegetables

Nuts

Cake Mixes

Batters

Vegetables

Cheese

Speed Setting & Uses for the Coffee and Spice Ninja® Grinder

FUNCTION CONTAINER

Grinding

1-877-646-5288

Coffee and Spice

Ninja Grinder

BLADE

TYPE

Grinder

SPEED or PROGRAM TYPE OF FOOD

High

Coffee Spices

Page 19

Care & Maintenance

HOW TO CLEAN

CAUTION: Make sure that the motor base is

unplugged from the power source before inserting or removing any attachment and before cleaning.

CAUTION: DO NOT immerse the motor base into

water or any other liquid.

CAUTION: Use caution when handling the blade

assemblies as the blades are very sharp.

1 Separate/remove all parts from each other.

2 Clean the motor base with a damp cloth and wipe dry.

NOTE: The Stainless Steel Ninja

dishwasher safe.

3 Place the lids, pitcher, bowl, Nutri Ninja

feed chute, jar, grinder and blade assemblies in the dishwasher. Place the lids and attachments on the toprack.

4 Carefully hand wash the lids, pitcher, bowl, Nutri

Ninja cups, discs, feed chute, jar, grinder and blade assemblies in warm, soapy water with a soft cloth.

Please call customer service if any servicing needs to

be performed on the appliance at 1-877-646-5288.

Cup is NOT

cups, discs,

HOW TO STORE

1 Store the Nutri Ninja | Ninja Blender System with Auto-iQ®

Technology upright with the pitcher on the motor base, stacked blade inside the pitcher and lid on the pitcher. Do not place anything on top. Store the Food Processor Bowl with the chopping blade inside and the lid on top. Store the Nutri Ninja cup and the rest of the attachments along side the appliance or in a cabinet where they will not be damaged and won’t cause a hazard. Be sure to store the grinder with lid attached.

RESETTING THE MOTOR THERMOSTAT

The Nutri Ninja | Ninja Blender System with Auto-iQ

Technology features a safety system which prevents damage to the unit’s motor and drive system should you inadvertently overload your appliance. If the appliance

is being overloaded, the motor will stop. Allow

the appliance to cool for approximately 15 minutes. To reset the appliance, follow the resetting

procedure below:

1 Unplug the appliance from the electrical outlet.

2 Remove and empty the container and ensure that no

food is jamming the blades or attachments.

3 Allow the appliance to cool for approximately 15

minutes.

4 Re-install the container onto the base and re-plug the

appliance into the electrical outlet.

5 Proceed to use the appliance as before making sure not

to exceed the recommended maximum capacities.

Page 20

Troubleshooting Guide

PROBLEMS POSSIBLE REASONS & SOLUTIONS

Motor Doesn’t Start or Attachment Doesn’t Rotate.

Make sure the container is securely locked into the motor base. Make sure the lid is securely on container in the correct position (align arrows). The appliance is turned “Off”. Press the power button ( ) to turn “On”. Check that the plug is securely inserted into the electrical outlet. Check the fuse or circuit breaker. The unit has overloaded. The appliance will stop and the power light will ﬂash.

Unplug and wait approximately 15 minutes before using again. The unit has overheated. Unplug and wait approximately 15 minutes before using again. Check to make sure the unit is not overloaded.

Food is Unevenly Chopped.

Food is Chopped Too Fine or is Too Watery.

Food Collects On Lid or On the Sides of the Container.

You Cannot Achieve Snow From Solid Ice.

Motor Base Won’t Stick to Counter or Table Top.

You get an “Err” Message.

You have a blinking red light.

Either you are chopping too much food at one time, or the pieces are not of even size and processing smaller amounts per batch.

The food has been over processed. Use Auto-iQ® Pulse button for controlled processing.

The mixture is too thick. Add more liquid.

Do not use ice that has been sitting out or has started to melt. Use ice straight from the freezer.

Start with a few pulses and then go to a continuous blending cycle.

Make sure surface and suction feet are wiped clean. Suction feet will only stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood, tile and non-polished ﬁnishes.

DO NOT attempt to use appliance when the motor base is stuck to a surface that is not secure, (cutting board, platter, plates, etc.).

Your Ninja® is able to detect which jar is on the base. You may be trying to use a program that is not designed for the jar you have installed. The programs will light up indicating which programs are available for each jar.

The unit is not installed properly. For your safety the unit will only be able to be turned on when it is properly assembled. Please refer to the assembly pages of this inspiration guide for assistance.

1-877-646-5288

Page 21

Notes

Page 22

**THIS WARRANTY IS FOR ALL COUNTRIES EXCEPT GERMANY**

ONE (1) YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1) year

from the date of purchase when utilised for normal household use, subject to the following conditions, exclusions and exceptions.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.

This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or

used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling

or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused

by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been

performed by a repair person not authorised by EURO-PRO Operating LLC.

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the

complete appliance and accessories, freight prepaid. For assistance with warranty service options or customer support, please

If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of

charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight. *

This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional

warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the speciﬁc obligations expressly assumed

by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential

damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or

consequential damages, so the above may not apply to you.

This Limited Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state or from

province to province.

*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and

to attach tag to item before packing with your name, complete address and phone number with a note giving

purchase information, model number and what you believe is the problem with the item. We recommend you

insure the package (as damage in shipping is not covered by your Limited Warranty). Mark the outside of your

package “ATTENTION CUSTOMER SERVICE”.

Product Registration

The registration will enable us to contact you in the unlikely event of a product safety notiﬁcation. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

1-877-646-5288

Page 23

**THIS WARRANTY IS FOR GERMANY ONLY**

TWO (2) YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of two (2) years

from the date of purchase when utilised for normal household use, subject to the following conditions, exclusions and exceptions.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.

This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or

used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling

or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused

by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been

performed by a repair person not authorized by EURO-PRO Operating LLC.