Page 1
BL682UK2
®
OWNER’S GUIDE
www.ninjakitchen.eu
0800 862 0453
Page 2
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY:
1 WARNING: Remove utensils prior to
READ ALL INSTRUCTIONS BEFORE USING
YOUR NUTRI NINJA® | NINJA® BLENDER
SYSTEM WITH AUTO-IQ® TECHNOLOGY.
2
WARNING: Extension cords are
not recommended for use with this
product.
3
WARNING: The blades are not
affixed to the unit. They are removable
and very sharp. Handle with care!
CAUTION: ln order to avoid a
hazard due to inadvertent resetting of
4
the thermal cut-out, this appliance must
not be supplied through an external
switching device, such as a timer, or
connected to a circuit that is regularly
switched on and off by the utility.
5
IMPORTANT: This appliance is not
intended for use by persons with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children shall not use or play with this
appliance. Close supervision is necessary
to keep appliance and cord out of reach of
children during use.
SAVE THESE
6
7
8 To protect against electrical shock, do not submerge
INSTRUCTIONS
WARNING:
processing. Failure to remove may cause the
jar to be damaged or to shatter which may
cause personal injury.
WARNING: The blade assemblies are
sharp, not locked in place and removable,
handle with care. When handling the blade
assemblies, always hold by the shaft. Failure
to do so will result in a risk of laceration.
WARNING: Stacked Blade Assembly is
sharp and not locked in place. If using the
pour spout, ensure the lid is fully locked onto
the pitcher. If pouring with the lid removed,
carefully remove the Stacked Blade Assembly
first, holding it by the shaft. Failure to do so
will result in a risk of laceration.
WARNING: Chopping Blade Assembly and
Mini Prep Bowl Blade Assembly are sharp and
not locked in place. Before emptying contents
carefully remove lid and Chopping Blade
Assembly or Mini Prep Bowl Blade Assembly,
holding it by the shaft. Failure to do will result
in risk of laceration.
CAUTION: Do not blend hot liquids, doing
so may cause excessive pressure build-up,
resulting in risk of the user being burned.
CAUTION: We do not recommend grinding
in any of our Nutri Ninja
CAUTION: Remove the Pro Extractor Blades
Assembly from the Nutri Ninja Cup upon
completion of blending. Do not store
ingredients before or after blending them in
the cup with the blade assembly attached.
Some foods may contain active ingredients or
release gases that will expand if left in a
sealed container, resulting in excessive
pressure buildup that can pose a risk of injury.
For ingredient storage in the cup, use only Sip
& Seal Lid or Spout Lid to cover.
the appliance or allow the power cord to come into
contact with water or any otherliquid.
®
Cups.
1
0800 862 0453
Page 3
9 DO NOT allow the appliance to be used by children.
Close attention is necessary when used near
children. This is not a toy.
10 Never leave an appliance unattended when in use.
11 Turn the appliance off and remove the power cord
from the electrical outlet when not in use, before
assembling or disassembling parts, accessing parts
that move while in use and before cleaning. To
unplug, grasp the plug and pull from the electrical
outlet. Never pull from the power cord.
12 DO NOT abuse the power cord. Never carry the
appliance by the power cord or yank it to disconnect
from electrical outlet; instead, grasp the plug and
pull to disconnect.
13 DO NOT use with damaged supply cord or plug.
If the supply cord or plug is damaged, it must be
replaced by the manufacturer, a service center or
similar qualified persons in order to avoid hazard.
14 DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged or left
outdoors.
15 NO SERVICEABLE PARTS. Incorrect re-assembly or
repair can cause a risk of electrical shock or injury
to persons when the appliance is used. Contact
Customer Service or a Service Center for the repair
or replacement under the warranty agreement.
16 Always use the appliance on a dry, level surface.
17 Keep hands, hair, clothing, as well as utensils out
of container while processing or blending to reduce
the risk of severe injury to persons or damage to the
appliance. A scraper may be used but only when the
appliance is not running.
18 Avoid contact with moving parts.
19 DO NOT attempt to sharpen blades.
20 DO NOT use the appliance if either set of blades are
bent or damaged.
21 To reduce the risk of injury, never assemble the
blade assemblies in the containers without the
pitcher or the bowl being properly attached to the
motor base.
22 DO NOT operate this appliance on or near any hot
surfaces (such as gas or electric burner or in a
heated oven).
23 The use of attachments or accessories including
canning jars, not recommended by the manufacturer
may result in fire, electric shock or personal injury.
24 DO NOT remove any container from the motor base
while the appliance is in operation. Always unplug
the unit when not in use.
25 To reduce risk of injury, never place the blade
assemblies on the base without the pitcher or Nutri
®
Ninja
Cup properly attached.
26 To reduce the risk of injury, NEVER operate the
appliance without the lid in place; DO NOT try to
defeat or bypass the interlock mechanism. When
using the removable blades, make sure they are
properly installed before operating the appliance.
27 DO NOT expose containers to extreme temperature
changes.
28 DO NOT let the power cord hang over the edge of
table or counter or touch hot surfaces such as the
stove.
29 DO NOT overfill. DO NOT exceed “MAX” fill line.
30 DO NOT operate the appliance empty.
31 To reduce the risk of burns, always allow the
appliance to cool before taking off parts and before
cleaning.
32 Max ON time is 60 seconds under 1500W load.
If the appliance overheats, a thermal switch will
become activated and shut off the motor. To reset,
unplug the appliance and let it cool down for
approximately 15 minutes before using again.
33 In the event that the unit overloads, the control panel
lights will flash and the unit will shut down. Unplug
the appliance and let it cool down for approximately
15 minutes before using again.
34 Max PULSE iteration is 30 pulses. After 30 pulses
allow 10 minutes to pass before running the PULSE
function up to an additional 30 pulses.
35 The maximum rating is based on the Stacked Blade
Assembly (pitcher) that drives the greatest power
and other recommended attachments may draw
significantly less power or current.
36 To avoid injury, never attempt to place the Pro
Extractor Blades
™
Assembly onto the motor base
without first assembling the blade assembly to the
Nutri Ninja Cup.
37 DO NOT push food into the food chute with your
fingers. Always use the food pusher provided.
38 Appliance accessories are not intended to be used
in the microwave as it may result in damage to the
accessories.
39 THIS PRODUCT IS INTENDED FOR HOUSEHOLD
USE ONLY. Do not use this appliance for anything
other than its intended use. Do not use outdoors.
www.ninjakitchen.eu
2
Page 4
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and
electronic equipment (WEEE).
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material sources. To return your used device, please use the return and collection
systems or contact the retailer where this product was purchased. They can take this
product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility (EMC)
2014/30/EU and its revisions, as well as Low Voltage Directive (LVD) 2014/35/EU and its revisions.
Guarantee: This product is unconditionally guaranteed for one year against all defects of
workmanship and materials. This guarantee does not affect your statutory rights. If this product
proves unsatisfactory please contact our customer service department on freephone 0800 862 0453
or by e-mail ukservice@euro-pro.com.
THIS BOOK COVERS MODEL NUMBERS:
BL682UK2 30
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1500W
Pitcher Capacity: 2.1L
Max Liquid: 2L
Bowl Capacity: 1.8L
Nutri Ninja
Cup Capacity: 500ml
650ml
®
3
0800 862 0453
Page 5
Contents
Thank you for
purchasing The
Nutri Ninja® |
Ninja® Blender
System with
Auto-iQ®
Technology.
Getting to Know Your Nutri Ninja | Ninja Blender System with Auto-iQ Technology ............... 5
Before First Use ............................................................................................................. 7
Assembly and Use for the Ninja Blender .......................................................................... 8
Assembly and Use for the Ninja Processor Bowl ............................................................. 10
Assembly and Use for the Cutting Discs .......................................................................12
Assembly and Use for the Nutri Ninja Cups ....................................................................14
Programs, Speed Settings, & Uses for the Pitcher ..........................................................16
Programs, Speed Settings, & Uses for the Food Processor ..............................................16
Programs, Speed Settings, & Uses for the Nutri Ninja Cups ............................................. 17
Care & Maintenance ....................................................................................................18
Troubleshooting Guide ..................................................................................................19
www.ninjakitchen.eu
4
Page 6
Getting To Know Your Nutri Ninja® | Ninja® Blender System with
Auto-iQ® Technology
a
b
c d
e
f
l
g
m
h
n
i
o
j
k
a 650ml Nutri Ninja Cup
b 500ml Nutri Ninja Cup
c Pro Extractor Blades™ Assembly
d Sip & Seal® Lid
5
0800 862 0453
e Food Processor Bowl
f Chopping Blade Assembly
(food processor)
g Dough Blade Assembly
(food processor)
h Feed Chute Lid
i Spindle for Discs
j Slicing/Shredding Disc
(food processor)
k Grating Disc (food processor)
l Pitcher
m Blender Lid with locking handle
n Stacked Blade Assembly (blender)
o Motor Base
NOTE: Blades are not interchangeable.
Page 7
The Nutri Ninja® | Ninja® Blender System with Auto-iQ® Technology is a high powered innovative tool with a sleek design
and outstanding performance, a true asset to any kitchen. The Nutri Ninja | Ninja Blender System with Auto-iQ Technology
features intelligent programs that combine pulsing, blending and pausing patterns that do the work for you. Get great
results every time with no guesswork required. For best results, be sure to carefully read all the instructions contained in
the manual before using this appliance.
Nutri Ninja | Ninja Blender System with Auto-iQ Technology Features:
• Patent Pending Ninja Blade Technology
• BPA Free pitcher (maximum liquid capacity 2L), Nutri Ninja Cups, Food Processor Bowl and Lids
• Drip-Free Pour Spout
• Total Crushing
• LED Control Panel with Timer
• Sturdy, Non-Slip Base
• Smart Lid technology for easy release
• 3 speeds: Low/Dough, Medium & High
• 5 Auto-iQ settings - Auto-iQ Frozen Drinks/Smoothies, Auto-iQ Food Puree, Nutri Ninja Auto-iQ Blend,
Nutri Ninja Auto-iQ Ultra Blend and Auto-iQ Pulse
• Nutrient & Vitamin Extraction*
*Extract a nutritious drink containing vitamins and nutrients from fruits and vegetables.
®
Technology
www.ninjakitchen.eu
6
Page 8
Before First Use
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
IMPORTANT: Make sure that the motor base is
plugged in for use.
IMPORTANT: Never add ingredients into the
container before placing the attachment in first.
IMPORTANT: Attachments are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it may
result in damage to the accessories.
WARNING: Stacked
Blade Assembly is
sharp and not locked in
place. If using the pour
spout, ensure the lid
is fully locked onto the
pitcher. Failure to do so
will result in a risk of
laceration.
WARNING: Stacked
Blade Assembly is sharp
and not locked in place.
If pouring with the lid
removed, carefully
remove the Stacked Blade
Assembly first, holding it
by the shaf t. Failure to do
so will result in a risk of laceration.
WARNING: Chopping
Blade Assembly is sharp and
not locked in place. Before
emptying contents carefully
remove lid and Chopping
Blade Assembly or Mini Prep
Bowl Blade Assembly, holding it by the
shaft. Failure to do will result in risk of
laceration.
CAUTION: Do not immerse the motor base into
water or any other liquid.
1 Remove all packaging material and labels from the
appliance.
2 Wash the lids, containers, discs and blade assemblies
in warm, soapy water. When washing the blade
assemblies, use a dish-washing utensil with a handle to
avoid direct hand contact with blades.
WARNING: Handle the blade assemblies and
discs with care when washing, as the blades are
sharp.
3 Handle blade assemblies with care to avoid contact
with sharp edges. Rinse and air dry thoroughly.
4 The lids, containers, discs and blade assemblies are all
dishwasher safe. It is recommended that the lids, blade
assemblies and discs be placed on the top rack. Ensure
the blade assemblies and discs are removed from the
containers before placing in the dishwasher.
5 Wipe the motor base clean with a damp cloth.
7
0800 862 0453
Separate/remove all parts from each other.
Page 9
Assembly and Use for the Ninja® Blender
HIGH
PULSE
LOW
DOUGH
SMOOTHIE
SINGLE
SERVE
PUREE
FROZEN
BLENDING
WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or
to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 1
LOW /
DOUGH
MED
Fig. 2
Fig. 4a Fig. 4b
1 Review warning and caution statements above before
proceeding to number 2.
2 Place the motor base on a clean, dr y, level surface such
as a counter or tabletop.
3 Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the Stacked Blade Assembly is seated
properly and is standing upright. (Fig. 1)
NOTE: The Stacked Blade Assembly will fit loosely on
the drive gear.
4 Place the motor base on a clean, dr y, level surface such
as a counter or tabletop.
5 Align and lower the pitcher onto the motor base.
(Fig. 2) Handle should be aligned slightly to the right of
the “LOCK” symbol on the motor base.
6 Rotate the pitcher clockwise until it locks in place, you
will hear a click when the lock is engaged. (Fig. 3)
7 The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 4a, Fig. 4b)
Fig. 3
Fig. 5b
Fig. 5a
8 Add the ingredients to the pitcher, making sure that
they do not exceed the highest measured marking line
on the side of the pitcher.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
“MA X LIQUID” mark (2 L) on the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
9 Holding the lid by the handle in the upright position, place
it on top of the pitcher aligning the triangle ( ) located on
the lid with the triangle ( ) located on the pitcher’s handle.
(Fig. 5a) Press the handle down until you hear a click.
The triangles on the lid and the blender handle MUST be
aligned in order for the blender to turn on. (Fig. 5b)
10 Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power light
( ) will flash and the motor will not work if the
pitcher and lid are not installed correctly. When
the pitcher and lid are installed properly, the
power light ( ) will be solid, indicating that the
appliance is ready for use.
www.ninjakitchen.eu
8
Page 10
Assembly and Use for the Ninja® Blender - cont.
Fig. 6
USE REMOVAL
Fig. 8
NOTE: Nutri Ninja® | Ninja® Blender System with
Auto-iQ® Technology can sense which jar is on the motor
base. The available function lights will illuminate depending
on which jar is placed on the motor base. (Fig. 6)
11 Review warning and caution statements at the top of page 8
before proceeding to number 12.
12 Press the power button to turn on the unit. Select
the speed or Auto-iQ program that best suits your
needs. The Auto-iQ program will stop the appliance
automatically at the end of the program. (Fig. 7)
NOTE: Pulse ingredients for even chopping by
holding the Auto-iQ PULSE button until your desired
consistency is reached.
NOTE: Max PULSE iteration is 30 pulses. After 30
pulses allow 10 minutes to pass before running the
PULSE function up to an additional 30 pulses.
13 To pause the appliance, press the selected speed or
Auto-iQ program a second time. When the program is
paused, the light on the program button will flash until
you press it again to resume the rest of the program.
14 When you have reached your desired consistency, stop
the appliance by pressing the power button ( ) and wait
for the Stacked Blade Assembly to stop turning. (Fig. 8)
9
0800 862 0453
Fig. 9Fig. 7
15 Turn the pitcher anticlockwise to remove and then lift
off the base. (Fig. 9)
CAUTION: Never inser t your hands in the pitcher as the
blades are sharp. Always use a spatula to dislodge
food that has stuck to the sides of the pitcher.
16 Open the pour spout cap and use the spout to empty
liquid contents.
17 For thicker consistencies, first remove the lid by
pressing the release button and pulling the lid handle
up to a 90 degree angle to lift lid off the pitcher. Then,
carefully remove the Stacked Blade Assembly by the
top of the shaft. Place Stacked Blade Assembly away
from the work area to avoid accidental contact. Finally,
empty contents from the pitcher. (Fig. 10)
18 Make sure that the unit is unplugged when not in use.
19 To release the motor base from the counter or tabletop,
place your hands underneath both sides of the motor base
and gently pull the unit up and towards you. (Fi g. 11)
Fig. 10 Fi g . 11
Page 11
Assembly and Use for the Ninja® Processor Bowl
MED
LOW /
DOUGH
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before emptying contents carefully remove lid
and Chopping Blade Assembly, holding it by the shaft. Failure to do will result in risk of laceration.
WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to shatter,
which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the user being
burned.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 1
LOW /
DOUGH
MED
Fig. 5a Fig. 5b
NOTE: Nutri Ninja® | Ninja® Blender System with
Auto-iQ® Technology can sense which jar is on the motor
base. The available function lights will illuminate depending
on which jar is placed on the motor base. (Fig. 1)
1 Review warning and caution statements above before
proceeding to number 2.
2 Place the motor base on a clean, dr y, level surface such
as a counter or tabletop.
3 Holding the desired blade by the top of the shaft, place it onto
the drive gear inside the bowl. Ensure that the attachment is
seated properly and is standing upright. (Fig. 2)
NOTE: The blade assembly will fit loosely on the drive gear.
4 Place the motor base on a clean, dr y, level surface such
as a counter or tabletop.
5 Align and lower the Processor Bowl onto the motor
base. (Fig. 3) Handle should be aligned slightly to the
right of the “LOCK” symbol on the motor base.
6 Rotate the bowl clockwise until it locks in place, you will
hear a click when the lock is engaged. (Fig. 4)
Fig. 2
Fig. 3
Fig. 4
Fig. 6b
Fig. 6a
7 The bowl can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 5a, Fig. 5b)
8 Add the ingredients to the bowl, making sure that they
do not exceed the “MAX” fill line on the side of the bowl.
9 Holding the feed chute lid, place it on top of the bowl and turn
clockwise aligning the arrow located on the lid with the arrow
located on the bowl’s handle. You will hear a click when the
lid is locked in place. (Fig. 6a) The triangles on the lid and
the Processor Bowl handle MUST be aligned in order for the
blender to turn on. (Fig. 6b)
NOTE: The 1.8 L bowl is not intended for blending
drinks. Do not overfill.
10 Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power button (
) will flash and the motor will not work if the bowl
and lid are not installed correctly. When the bowl and
lid are installed properly, the power button ( ) will be
solid, indicating that the appliance is ready for use.
www.ninjakitchen.eu
10
Page 12
Assembly and Use for the Ninja® Processor Bowl - cont.
REMOVAL
Fig. 2 Fig. 3 Fig. 5Fig. 1
USING THE CHOPPING BLADE ASSEMBLY
1 Review warning and caution statements at the top of page 10
before proceeding to number 2.
2 Holding the Chopping Blade Assembly assembly by the shaft,
place it onto the gear shaft inside the bowl. Ensure that the
Chopping Blade Assembly fits around the gear shaft and that
it is standing straight.
3 Add the ingredients and secure the bowl lid onto the bowl.
(Fig. 1)
4 Plug the power cord into the electrical outlet and press on the
power button ( ).
5 Select the speed or Auto-iQ® program that best suits your
needs. Pulse ingredients for even chopping by holding
the Auto-iQ PULSE button until your desired consistency is
reached.
NOTE: Max PULSE iteration is 30 pulses. After 30 pulses
allow 10 minutes to pass before running the PULSE function
up to an additional 30 pulses.
NOTE: Please refer to “Speed Settings & Uses” chart for
suggested uses and speeds.
6 When you have reached your desired consistency, stop the
appliance by pressing the power button ( ) and wait for the
blade to stop turning. (Fig. 2)
7 To remove the lid, press the release button on the lid and turn
it anticlockwise. (Fig. 2)
8 Turn the bowl anticlockwise and lift it to remove it from the
motor base. (Fig. 3)
9 To release the motor base from the counter or tabletop, place
your hands underneath both sides of the motor base and
gently pull the unit up and towards you. (Fig. 4)
USEUSE
Fig. 4
USING THE DOUGH BLADE ASSEMBLY
1 Review warning and caution statements at the top of page 10
before proceeding to number 2.
2 Holding the Dough Blade Assembly by the shaft, place it onto
the gear shaft inside the bowl. Ensure that the Dough Blade
Assembly fits around the gear shaft and that it is standing
straight. (Fig. 5)
3 Add the ingredients and secure the bowl lid onto the bowl.
4 Plug the power cord into the electrical outlet and press on
the power button (
process until ingredients come together to form a mass.
NOTE: Please refer to “Speed Settings & Uses” chart for
suggested uses and speeds.
5 Once finished making dough, stop the appliance by pressing
the power button (
6 To remove the lid, press the release button on the lid and and
turn it anticlockwise. (Fig. 2)
7 Turn the bowl anticlockwise and lift it to remove it from the
motor base. (Fig. 3)
8 To release the motor base from the counter or tabletop, place
your hands underneath both sides of the motor base and
gently pull the unit up and towards you. (Fig. 4)
). Select the LOW/DOUGH button and
) and wait for the blade to stop turning.
11
0800 862 0453
Page 13
Assembly and Use for the Cutting Discs
WARNING: The Cutting Discs are sharp. Always use the finger holes when placing or removing the cutting
discs. Failure to do so will result in a risk of laceration.
WARNING: Remove utensils prior to processing. Failure to remove may cause the bowl to be damaged or to
shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
IMPORTANT: Make sure that the motor base is plugged in for use.
USING THE DISCS
NOTE: Cutting Discs must be used with the feed
chute lid.
1 Review warning statements above before proceeding to
number 2.
2 Place the motor base on a clean, dr y, level surface
such as a counter or tabletop. Press down on the motor
base to make sure that the suction cups adhere to the
counter or tabletop. (Fig. 1)
3 Secure the bowl onto the motor base.
4 Place the spindle inside the bowl.
5 Use the finger holes to grasp the selected disc and
place it over the spindle.
6 Place the feed chute lid on the bowl and turn clockwise
until you hear a click indicating the lid is locked in
place. (Fi g. 1)
7 Plug the power cord into the electrical outlet and press
up on the power toggle (
8 Select LOW/DOUGH on the control panel. The discs will
begin spinning.
9 Add the food that you want to slice, shred or grate
through the feed chute on the lid. ( Fig. 1) Use the
two-part food pusher to help guide the food through
the feed chute. The middle piece of the food pusher is
removable to use for smaller ingredients.
10 When finished,stop the appliance by pressing the
power button (
Press the but ton on the feed chute lid located near the
handle to unlock and turn the lid anticlockwise. Lift to
remove from the processor bowl. Using the finger holes,
carefully lift the disc out of the bowl and remove the
spindle.
11 To release the motor base from the counter or tabletop,
place your hands underneath both sides of the motor
base and gently pull the unit up and towards you.
) to turn the power “On”.
) and wait for the disc to stop turning.
Fig. 1
www.ninjakitchen.eu
12
Page 14
Assembly and Use for the Nutri Ninja® Cups
WARNING: Handle the Pro Extractor Blades™ Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the Nutri Ninja Cup to be
damaged or to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
CAUTION: Remove the Pro Extractor Blades Assembly from the Nutri Ninja Cup upon completion of
blending. Do not store ingredients before or after blending them in the cup with the blade assembly
attached. Some foods may contain active ingredients or release gases that will expand if left in a sealed
container, resulting in excessive pressure buildup that can pose a risk of injury. For ingredient storage in
the cup, use only Sip & Seal Lid or spout lid to cover.
ASSEMBLY
Fig. 1
IMPORTANT: When processing soft dry
ingredients such as day-old bread or cheese
use quick, short 1 second pulses. Do not over fill
to avoid overheating the appliance. Allow the
appliance to cool after each use.
NOTE: Nutri Ninja | Ninja
®
Blender Duo with Auto-iQ®
Technology can sense which jar is on the motor base.
The available function lights will illuminate depending
on which jar is placed on the motor base. (Fig. 1)
1 Review warning and caution statements above
before proceeding to number 2.
2 Place the motor base on a clean, dr y, level surface
such as a counter or tabletop. Press down on the motor
base to make sure that the suction cups adhere to the
counter or tabletop.
13
0800 862 0453
Fig. 2
Fig. 3
3 Add ingredients to the Nutri Ninja Cup.
4 Place the Pro Extractor Blades Assembly onto the cup
and tightly screw it on clockwise until you have a good
seal. (Fig. 2)
5 Turn the Nutri Ninja Cup upside down and place it onto
the motor base, aligning the tabs on the cup with the
motor base. Rotate the Nutri Ninja Cup clockwise until
it locks in place, you will hear a click when the lock is
engaged. (Fig. 3)
Page 15
USE REMOVAL
Fig. 4 Fig. 5 Fig. 6
6 Review warning and caution statements on page
13 before proceeding.
7 Press the power button on, and select the speed or
Auto-iQ program that suits your needs. (Fig. 4) The
Auto-iQ program will stop the appliance automatically
at the end of the program.
8 To pause the appliance, press the selected speed or
Auto-iQ program a second time. When the program is
paused, the light on the program button will flash until
you press it again to resume the rest of the program.
9 Once you have reached your desired consistency, stop
the appliance by pressing the power button and wait for
the Pro Extractor Blades Assembly to stop turning. Turn
the Nutri Ninja
®
Cup anticlockwise and pull straight up
to remove. (Fig. 5, Fig. 6)
NOTE: Do not overfill. To avoid spilling, do not add
ingredients past the “MAX” fill line.
10 Turn the cup upright and remove the Pro Extractor
Blades Assembly by twisting the Pro Extractor Blades
Assembly anticlockwise. (Fig. 7)
11 Do not store blended contents with the Pro Extractor
Blades attached attached.
12 Place the Sip & Seal
to seal and enjoy.
13 For storage, use Sip & Seal Lid to cover.
14 Be sure to store the Pro Extractor Blades attached to an
empty cup when not in use.
15 Make sure that the motor base is
unplugged when not in use.
16 To release the motor base
from the counter or tabletop,
place your hands underneath
both sides of the motor base
and gently pull the unit up and
towards you.
Fig. 7
®
Lid onto the Nutri Ninja Cup, twist
www.ninjakitchen.eu
14
Page 16
Programs, Speed Settings & Uses for the Pitcher
FUNCTION CONTAINER
Frozen Drinks /
Ice Crush
Pureeing Pitcher
Pitcher
BLADE
TYPE
Stacked Blade
Assembly
Stacked Blade
Assembly
SPEED or PROGRAM TYPE OF FOOD
Auto-iQ® Frozen Drinks/
Smoothies
Auto-iQ Food Puree
Programs, Speed Settings & Uses for the Food Processor
FUNCTION CONTAINER BLADE TYPE
Mincing
Kneading and
Dough Mixing
Processing
Emulsifying
Grinding
Grating
Chopping
Batters
Slicing/Shredding
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Food Processor
Bowl
Chopping Blade
Assembly
Dough Blade
Assembly
Chopping Blade
Assembly
Chopping Blade
Assembly
Chopping Blade
Assembly
Chopping Blade
Assembly
Grating Disc
Chopping Blade
Assembly
Dough Blade
Assembly
Reversible Slicing
Shredding Disc
SPEED or
PROGRAM
Auto-iQ® Pulse
Low/Dough
Auto-iQ Food Puree
Low/Dough
Medium
High
Low/Dough
Medium
Medium Meat
Auto-iQ Pulse
Low/Dough (when
using Disc)
Auto-iQ Pulse
Low/Dough
Low/Dough
Ice
Frozen Drinks
Smoothies
Smoothies
Soups*
Milkshakes
TYPE OF FOOD
Onion
Garlic
Herbs
Bread Dough
Pie Dough
Pizza Dough
Pretzel Dough
Cookie Dough
Pâtés
Stewed Fruits
Dips
Apple Sauce
Spreads
Salad Dressings
Dips
Sauces*
Grated Cheese
Bread Crumbs
Spices
Salsa
Vegetables
Nuts
Cake Mixes
Batters
Vegetables
Cheese
* When blending sauces and soups, make sure they’re cooled to room temperature first - Ninja® containers are not intended for
hot blending.
15
0800 862 0453
Page 17
Programs, Speed Settings & Uses for the Nutri Ninja® Cup
FUNCTION CONTAINER
Smoothies Nutri Ninja
Green Smoothies Nutri Ninja Cup
Grating Nutri Ninja Cup
Chopping Nutri Ninja Cup
®
Cup
BLADE
TYPE
Pro Extractor
Blades™
Assembly
Pro Extractor
™
Blades
Assembly
Pro Extractor
™
Blades
Assembly
Pro Extractor
™
Blades
Assembly
SPEED or PROGRAM TYPE OF FOOD
Smoothies
Nutri Ninja Auto-iQ Blend
Nutri Ninja Auto-iQ Ultra
Blend
Auto-iQ Pulse
Nutri Ninja Auto-iQ Blend
High
Auto-iQ Pulse
Nutri Ninja Auto-iQ Blend
High
Frappes
Milkshakes
Protein Drinks
Frozen Fruits
Frozen Vegetables
Kale
Celery
Spinach
Seeds
Ice
Grated Cheese
Bread Crumbs
Salsa
Vegetables
Nuts
www.ninjakitchen.eu
16
Page 18
Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
1 Separate/remove all parts from each other.
2 Hand Washing:
assemblies and attachments in warm, soapy water
When washing the blade assemblies, use a dish-washing
utensil with a handle to avoid direct hand contact with
blades. Handle blade assemblies with care to avoid
contact with sharp edges. Rinse and air dry thoroughly.
Dishwasher: The containers, lids, blade assemblies
and at tachments are all dishwasher safe. The lids
and blade assemblies are top rack dishwasher safe.
Ensure that the blade assemblies are removed from the
containers before placing in the dishwasher.
WARNING: Handle the blade assemblies with care
when washing, as the blades are sharp. Contact
with the blades’ edges can result in laceration.
3 Wipe the motor base clean with a damp cloth
Please call customer service if any servicing needs to
be performed on the appliance at 1-877-646-5288.
Wash the containers, lids, blade
.
.
HOW TO STORE
1
Store the Nutri Ninja® | Ninja® Blender Duo™ with
AUTO-iQ™ Technology upright with the blade assembly
inside the corresponding container with the lid secured
on top. Do not place anything on top. Store the rest
of the attachments in a safe place where they will not
be damaged and won’t cause harm. Loosely wrap the
power cord around the motor base
NOTE:
Do not store blended or unblended ingredients in
the Nutri Ninja Cup with the blade assembly attached.
RESETTING THE MOTOR THERMOSTAT
Store the N
Auto-iQ® Technology features a unique safety system
which prevents damage to the unit’s motor and
drive system should you inadver tently overload your
appliance. If the appliance is being overloaded,
the motor will stop. Allow the appliance to
cool for approximately 15 minutes. To reset the
appliance, follow the resetting procedure below:
1
Unplug the appliance from the electrical outlet.
2
Remove and empty the container and ensure that no
food is jamming the blade assembly.
3
Allow the appliance to cool for approximately 15
minutes.
4
Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5
Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.
utri Ninja® | Ninja® Blender System with
17
0800 862 0453
Page 19
Troubleshooting Guide
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor Doesn’t Start or Blade
Assembly Doesn’t Rotate.
Make sure the container is securely locked into the motor base.
Make sure the lid is securely on container in the correct position (align arrows).
The appliance is turned “Off”. Press the power button (
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power light will flash.
Unplug and wait approximately 15 minutes before using again.
The unit has overheated. Unplug and wait approximately 15 minutes before using again.
Check to make sure the unit is not overloaded.
) to turn “On”.
Food is Unevenly Chopped.
Food is Chopped Too Fine or is
Too Watery.
Food Collects On Lid or On the
Sides of the Container.
You Cannot Achieve Snow
From Solid Ice.
Motor Base Won’t Stick to
Counter or Tabletop.
You get an “Err” Message.
You have a blinking red light.
Either you are chopping too much food at one time, or the pieces are not of even
size and processing smaller amounts per batch.
The food has been over processed. Use Auto-iQ® PULSE button for controlled
processing.
The mixture is too thick. Add more liquid.
Do not use ice that has been sitting out or has started to melt. Use ice straight
from the freezer.
Start with a few pulses and then go to a continuous blending cycle.
Make sure surface and suction feet are wiped clean. Suction feet will only stick to
smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood,
tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to a surface that
is not secure, (cutting board, platter, plates, etc.).
Your Ninja® is able to detect which jar is on the base. You may be trying to use a
program that is not designed for the jar you have installed. The programs will light
up indicating which programs are available for each jar.
The unit is not installed properly. For your safety the unit will only be able to be
turned on when it is properly assembled. Please refer to the assembly pages of
this inspiration guide for assistance.
www.ninjakitchen.eu
18
Page 20
Euro-Pro Europe Limited
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
United Kingdom
Freephone 0800 862 0453
www.ninjakitchen.eu
Copyright © 2016 Euro-Pro Europe Limited.
Auto-iQ, Nutri-Ninja, Ninja, Sip & Seal and Total Crushing are
registered trademarks of Euro-Pro Europe Limited.
Pro Extractor Blades and Blender Duo are trademarks of EuroPro Europe Limited.
Printed in China
Illustrations may differ from actual product. We are constantly striving to improve our
products, therefore the specifications contained herein are subject to change without notice.
BL682UK2_30_IB_160812_1
Loading...