Page 1
OWNER’S GUIDE
®
BL492 Series
1-877-646-5288
Page 2
®
THANK YOU!
Welcome to the Nutri Ninja® Auto-iQ® Pro Compact System all-purpose,
customisable, everyday kitchen assistant. The Nutri Ninja Auto-iQ Pro Compact
System features pre-programmed settings that take the guesswork out of drink and
meal making. These programs are timed to deliver consistent, delicious results
that finish on their own so all you have to do is press a button and enjoy.
REGISTER YOUR PURCHASE:
RECORD THIS INFORMATION:
Model Number: ���������������������������������������������
Date of Purchase (Keep receipt):
����������������������������������������������������������
THIS BOOK COVERS MODEL NUMBER:
BL492 ***** 30
1- 877-646-5288
If you should have a question about your Nutri Ninja Auto-iQ Pro Compact System,
please call the Ninja Customer service line at 1-877-646-5288.
TECHNICAL SPECIFICATIONS:
Voltage: 220-240V~, 50/60Hz
Power: 1200W
Pitcher Capacity: 2.1 L
Max Liquid Capacity: 2.0 L
Processor Bowl Capacity: 1.2 L
Nutri Ninja
Nutri Ninja® Cup Capacity: 300ml
500ml
650ml
900ml
Nutri Ninja® Double Wall
Stainless Steel Cup Capacity: 650ml
®
Jar Capacity: 1.4 L
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and electronic equipment (WEEE).
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To
return your used device, please use the return and collection systems or contact the retailer where this product was purchased. They can take
this product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibilit y (EMC) 2004/108/EC and its revisions, as well as Low Voltage
Directive (LVD) 20 06/95/EC and its revisions.
2
Page 3
®
READ ALL INSTRUCTIONS BEFORE USE
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic safety precautions should always be observed,
including the following:
IMPORTANT: This appliance is not intended for use by persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children shall not use or play with this appliance. Close supervision is necessary to keep
appliance and cord out of reach of children during use.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
1 WARNING: Extension cords are not recommended for use with this product.
WARNING: Never leave the appliance unattended while in use.
2
CAUTION: ln order to avoid a hazard due to inadvertent resetting of the thermal
3
cut-out, this appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regularly switched on and
off by the utility.
4
CAUTION: Blade assembly is sharp, handle with care. When handling the blade
assembly, always hold by the top of the blade assembly.
5
CAUTION: DO NOT BLEND HOT LIQUIDS. Allow the liquids and foods to cool to
room temperature before blending.
6 CAUTION: Do not blend dry ingredients unless pulsing for short intervals per the
instructions. Continuous blending dry ingredients will overheat the blender.
7 CAUTION: Never attempt to remove the container (cup, processor bowls, etc.) while
the appliance is still running.
8 IMPORTANT: Never add ingredients to the containers (processor bowl, pitchers, etc.)
before inserting the blade assembly first.
9 IMPORTANT: Do not attempt to operate the container (processor bowls, pitchers, etc.)
without the lid on.
10 IMPORTANT: Never run the appliance empty.
11 IMPORTANT: Make sure that the motor base is plugged in for use.
12 IMPORTANT: Make sure that the motor base is unplugged when not in use.
13 To protect against electrical shock, do not submerge the appliance or allow the power cord to
come into contact with water or any other liquid.
14 DO NOT allow children to operate the appliance or use as a toy. Close supervision is necessary
when any appliance is used near children.
15 Never leave the appliance unattended when in use.
16 Turn the appliance off and remove the power cord from the electrical outlet when not in use,
before assembling or disassembling parts, accessing parts that move while in use and before
cleaning. To unplug, grasp the plug and pull from the electrical outlet. Never pull from the power
cord.
17 DO NOT abuse the power cord. Never carry the appliance by the power cord or yank it to
disconnect from the electrical outlet; to unplug, grasp the plug, not the cord.
18 DO NOT use with damaged cord or plug.
19 DO NOT USE if the appliance is not working, after it has been dropped, dropped into water,
damaged or left outdoors.
20 NO SERVICEABLE PARTS. Incorrect re-assembly or repair can cause a risk of electrical shock or
injury to persons when the appliance is used.
21 DO NOT let the power cord hang over the edge of a table or counter or touch hot surfaces such as
the stove.
22 Always use the appliance on a dry, level surface. Make sure the suction-cup feet are wiped clean
and no crumbs or residue are on the bottom of them.
23 Keep hands, hair, clothing, and utensils out of container while processing to reduce the risk of
severe injury to persons or damage to the appliance. A scraper may be used ONLY when the
appliance is not running.
24 Avoid contact with moving parts.
25 DO NOT attempt to sharpen blade assemblies.
26 DO NOT use the appliance if the blade assembly is bent or damaged.
27 To reduce risk of injury, never place the blade assembly on the motor base without the proper
container.
28 DO NOT operate this appliance on or near any hot surfaces (such as on a gas or electric burner or
in a heated oven).
29 The use of attachments or accessories (including canning jars), that are not recommended or sold
by the manufacturer may cause fire, electric shock, or personal injury.
30 DO NOT remove the container (cup, processor bowl, etc.) from the motor base while the appliance
is running.
31 To reduce the risk of injury, NEVER operate the appliance without the blade assembly installed in a
container. DO NOT try to defeat the interlock mechanism; make sure the blade is properly installed
before operating the appliance.
32 DO NOT expose containers (cups, processor bowls, etc.) to extreme temperature changes.
33 DO NOT overfill.
34 Max ON time is 60 seconds under 1200W load. If the appliance overheats, a thermal switch will
become activated and shut off the motor. To reset, unplug the appliance and let it cool down for
approximately 30 minutes before using again.
35 MAX Chop program run is 2 full runs (30 pulses). After 2 consecutive Chop program runs allow
10 minutes to pass before running the Chop program again for up to an additional further 2
consecutive runs (30 pulses).
36 To reduce the risk of burns, always allow the appliance to cool before taking off parts and before
cleaning.
37 To avoid injury, never attempt to place the Pro Extractor Blade
assembling the blade assembly to the Nutri Ninja
38 THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use this appliance for anything
other than its intended use. Do not use outdoors.
39 Appliance accessories are NOT intended to be used in the microwave. DO NOT place the container
(cups, processor bowls, lids, etc.) in the microwave as it may result in damage to the accessories.
40 The maximum power rating is based on the chopping blade (processor bowl) that drives the
greatest power; other recommended attachments may draw significantly less power or current.
41 When using the grinder accessory, DO NOT remove Cover until blade has COMPLETELY STOPPED
42 When using the grinder accessory, DO NOT attempt operation without the cover being in place.
43 When using the grinder accessory, DO NOT process liquid ingredients. The grinder accessory is not
intended for liquid processing.
44 When using the grinder accessory, DO NOT attempt to chop ice.
45 Check Stainless Steel cup or grinder accessory for presence of foreign objects before using.
®
Cup.
™
onto the motor base without first
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
1-877-646-5288
3
Page 4
®
ACCESSORIES
®
Nutri Ninja
WAR NING: DO
Cups
NOT B LEND HO T
LIQUIDS
300 ml 500 ml 900 ml650 ml
Sip &
®
Lid
Seal
NOT E: Sip & Se al lid, Spou t lid and Pr o Extr actor Bla des can be use d with all N inja Cups .
Pro Extractor
Blades
™
Spout Lid
Double Wall
Stainless Steel
Nutri Ninja Cup
WAR NING: DO
NOT B LEND HO T
LIQUIDS
650 ml
Shaker Lid
Nutri Ninja Jar
WAR NING: DO
NOT B LEND HO T
LIQUIDS
1.4 L
Silicone Grip
Sleeve
Blade Assembly
Pitcher/Lid
Max liquid capacity:
2 L
(pitcher)
2.1 L
4
Page 5
®
ACCESSORIES
Processor Bowl
1.2 L
Feed Chute
(food processor)
Chopping Blade
(food processor)
Spindle
(food processor)
Dough Blade
(food processor)
Slicing/Shredding
Disc
(food processor)
Grating Disc
(food processor)
Motor Base
1-877-646-5288
5
Page 6
®
FEATURES:
• Nutrient&VitaminE xtraction
• 1200WattMotor
• UserInterface:
Start/Stop
Start/Stop is a manual setting that runs at High speed for 60 seconds. This button can be pressed at any time if you wish to stop a program.
Smooth Boost™
SMOOTH BOOST YES/NO is a special feature available when using the Auto-iQ® EXTRACT and Auto-iQ BLEND. This set ting can be used to control the consistency of your beverage
recipes. Select SMOOTH BOOST YES when smoother, creamier results are desired. This is the default program for both Auto-iQ EX TRACT and Auto-iQ BLEND programs. Select
SMOOT H BOOST NO when more of a textured consistency is desired.
Pulse
Of fers greater control to help prevent over-processing or over-blending. Simply hold down the button and our blades will run at a high speed for a quick burst of power to break through
ice or chop vegetables.
Low
LOW is a manual setting that runs for 30 seconds and will automatically shut off. On this setting, blades rotate at a slower speed, allowing heavy recipes like doughs to be mixed.
AUTO-IQ E XTRACT†
EXTRACT should be used w hen blending hard, leafy, or fibrous whole fruits and vegetables, including apples, kale, and celery. This optimized program allows you to blend fresh items
with their skins, seeds, and stems into nutrient extractions. Before using EX TRACT, select Smooth Boost YES or NO depending on your desired consistency.
AUTO-IQ BLEND
BLEND can be used to make a range of beverages that do not include hard or fibrous fresh ingredients, such as milkshakes, protein smoothies, soft fresh-fruit smoothies, and frozen
cocktails. Before using BLEND, select SMOOTH BOOST YES or NO depending on your desired consistency.
AUTO-IQ CHOP
CHOP is a program composed of timed pulses and pauses to deliver consistent chopping results for a range of recipes including ingredient prep, salsas, and ground meat. When
ingredients have reached your desired consistency, stop by selecting AUTO-IQ CHOP or Start/Stop.
• Sip&Seal® lids for drinks on the go.
• NutriNinja®CupsandSip&Seallids,BPAfree,anddishwashersafe.
NOTE: The Stainless Steel Nutri Ninja® Cup is NOT dishwasher safe.
• 1.2LFoodProcessorB owl&lid,areBPAfree,anddishwashersafe.
• 2.1LPitcher(maxliquidcapacity:2L)&lid,BPAfree,anddishwashersafe.
• CordWraplocatedonbackofthemotorbase.
Ice to Snow
Crushing Ice to Snow is easy – take ice cubes directly from your freezer, and put in a dr y Ninja® Cup – use the pulse feature in short quick bursts until it’s a snow like consistency.
†
†
Extract a drink containing vitamins and nutrients
from fruit s and vegetables.
6
Page 7
®
or or
B C D E FA
USE REMOVALASSEMBLY
For best results, follow the recipe/ingredient loading instructions found in your Inspiration Guide.
CAUTION: DO NOT BLEND HOT LIQUIDS. Allow the liquids and foods to cool to room temperature before blending.
CAUTION: Do not put hot liquids in the Stainless Steel 65 0 ml Nutri Ninja Cup before blending. Start with cool or room temperature liquid. Heated liquid can create
internal pressure in a sealed cup, which may erupt on opening and cause a burn injury.
IMPORTANT: Do not overfill. to avoid spilling, do not add ingredients past the “M AX” fill line.
IMPORTANT: When processing soft dry ingredients such as day-old bread or cheese use quick, short 1 second pulses. Do not over fill to avoid overheating the appliance.
Allow the appliance to cool after each use.
ASSEMBLY &
USE OF THE
NUTRI NINJA®
CUP
NOTE: Ninja® Auto-iQ®
Technology can sense
which container is on the
motor base. The function
lights will illuminate
depending on which
Nutri Ninja Cup is placed
on the motor base.
BEFORE FIRST USE:
• Remove all packaging material and labels from
the appliance.
• Wash the lids, cups, blades, and Blend and Prep
Bowl in warm, soapy water with a soft cloth.
• Rinse and dr y thoroughly.
• NOTE: The Double Wall Stainless Steel Nutri
Ninja Cup is NOT dishwasher safe.
•
Lids, cups, blades, and pitcher are all dishwasher
safe. It is recommended that the lids and
attachments be placed on the top rack. Ensure that
the Pro Extractor Blades
beforeplacinginthedishwasher.
• Wipe the motor base clean with a damp cloth.
™
are removed from the cups
ASSEMBLY:
WARNING: NE VER LEAV E THE APPLIANCE
UNAT TENDED WHILE IN USE.
CAUTION: PRO EXTRACTOR BLADES™
ARE SHARP AND REMOVABLE, H ANDLE
WIT H CARE. WHEN HANDLING THE PRO
EX TRACTOR BLADES, DO NOT HOLD T HE
BLADES, ALWAYS HOLD BY THE BASE OF
THE BLADE ASSEMBLY.
IMPORTAN T: MAK E SURE THE MOTOR
BASE IS PLUGGED IN FOR USE .
1 Place the motor base on a clean, dry, level
surface such as a counter or tabletop. Press
down on the motor base to make sure the
suction cups adhere to the counter or tabletop.
2 Add ingredients to the Nutri Ninja cup.
3 Place the Pro Ex tractor Blades onto the cup and
tightly screw on clockwise (A) until you have a
good seal.
4 Turn the Nutri Ninja cup upside down and place
it onto the motor base (B), aligning the tabs on
the cup with the motor base. Rotate the Nutri
Ninja cup clockwise until it locks in place (you
will hear a click when the lock is engaged).
USE:
5 Once the cup is engaged, the programs available
for that attachment will illuminate. Select
the program (C) desired based on your recipe.
The Auto-iQ program will stop the appliance
automatically at the end of the program.
6 To pause the program, press the selected
speed or Auto-iQ Program a second time.
1-877-646-5288
REMOVAL:
7 Once you have reached your desired
consistency, press the START/STOP button to
turn the program off. Turn the Nutri Ninja cup
anticlockwise (D) and pull straight up to remove
(E).
8 Turn the cup upright and remove the Pro
Extractor Blades by twisting the Pro Extractor
Blades anticlockwise.
9 PlacetheSip&Seal
cup, twist to seal, and enjoy!
10 Make sure the appliance is unplugged when not
inuse.
11 To release the motor base from the counter or
tabletop, place your fingers under the sides of
the black paddles on the sides of the base and
lift up to release suction cup feet (F).
®
lid onto the Nutri Ninja
7
Page 8
®
2.1 L PITCHER
(Max Liquid Capacity: 2 L)
A B C D E F
ASSEMBLY
G
If your unit comes with this accessory, read the following instructions. For a list of what is included with this model, refer to inside flap of the box.
CAUTION: THE BLADE ASSEMBLY
IS NOT LOCKED IN PL ACE. IF USING
THE POUR SPOUT, ENSURE THE
LID IS FULLY LOCKED ONTO THE
BLENDER PITCHER.
ASSEMBLY
OF THE 2.1 L
PITCHER
(Max Liquid Capacity: 2 L)
NOTE: Ninja® Auto-iQ®
Technology can sense
which container is on the
motor base. The function
lights will illuminate
depending on which
container is placed on
the motor base.
ASSEMBLY:
WARNING: NE VER LEAV E THE APPLIANCE
UNAT TENDED WHILE IN USE.
CAUTION: USE CAUTION WHEN
HANDLING THE BL ADE ASSEMBLY AS IT
IS VERY SHARP.
IMPORTAN T: MAK E SURE THE MOTOR
BASE IS PLUGGED IN FOR USE .
1 Holding the Blade Assembly by the top of the
shaft, place it onto the drive gear (A) inside the
pitcher. Ensure that the attachment is seated
properly and is standing upright.
NOTE: THE BLADE ASSEMBLY WILL FIT
LOOSELY ON THE DRIV E GEAR.
8
CAUTION: THE BLADE
ASSEM BLY IS NOT LOCKED IN
PLACE . IF POURING WITH THE
LID REMOVED, ALWAYS REMOVE
THE BLADE ASSEMBLY FIR ST.
2 Place the motor base on a clean, dry, level
surface such as a counter or tabletop. Press
down on the motor base to make sure the
suction cups adhere to the counter or tabletop.
3 Align and lower the pitcher (B) onto the motor
base. Handle should be aligned slightly to the
right of the LOCK symbol on the motor base.
4 Rotate the pitcher clockwise (C) until it locks in place
(you will hear a click when the lock is engaged).
5 The pitcher can be placed on the motor base
two ways; the handle can align with the front
right corner (D) or the front left corner (E).
6 Add the ingredients to the pitcher, making
sure they do not exceed the highest measured
marking line on the side of the pitcher.
IMPORTANT: DO NOT OVERFILL. TO AVOID
SPILLING, DO NOT ADD INGREDIENTS PAST
THE “MAX LIQUID” LINE.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed
the MAX LIQUID mark (2 L) on the pitcher.
NOTE: If you need to add additional ingredients
once the appliance is processing, turn the unit
OFF, open the pour spout cap, and pour the
ingredients in through the opening.
7 Holding the lid by the handle in the upright
position (F), place it on top of the pitcher
aligning the triangle ( ) located on the lid with
the triangle ( ) located on the pitcher handle.
Press the handle down until you hear a click.
8 The triangles on the lid and the pitcher handle
(G) MUST be aligned for the blender to turn on.
9 Plug the power cord into the electrical outlet.
The function lights will illuminate.
Page 9
®
H I J K
USE REMOVAL
If your unit comes with this accessory, read the following instructions. For a list of what is included with this model, refer to inside flap of the box.
CAUTION: THE BLADE ASSEMBLY
IS NOT LOCKED IN PL ACE. IF USING
THE POUR SPOUT, ENSURE THE
LID IS FULLY LOCKED ONTO THE
BLENDER PITCHER.
USING THE 2.1 L
PITCHER
(Max Liquid Capacity: 2 L)
NOTE: Ninja® Auto-iQ®
Technology can sense
which jar is on the motor
base. The function
lights will illuminate
depending on which
container is placed on
the motor base.
USE:
WARNING: NE VER LEAV E THE APPLIANCE
CAUTION: USE CAUTION WHEN
IMPORTAN T: MAK E SURE THE MOTOR
1 Once the pitcher is engaged, the programs
UNAT TENDED WHILE IN USE.
HANDLING THE BL ADE ASSEMBLY AS IT
IS VERY SHARP.
BASE IS PLUGGED IN FOR USE .
available for that attachment will illuminate.
Select the program desired (H) based on your
recipe. The Auto-iQ program will stop the
appliance automatically at the end of the program.
CAUTION: THE BLADE
ASSEM BLY IS NOT LOCKED IN
PLACE . IF POURING WITH THE
LID REMOVED, ALWAYS REMOVE
THE BLADE ASSEMBLY FIR ST.
NOTE: Pulse ingredients for even chopping by
holding the PULSE button until your desired
consistency is reached.
2 To pause the program, press the selected speed
a second time. When the program is paused, the
light on the program button will flash until you
press it again to resume the rest of the program.
1-877-646-5288
IMPORTANT: DO NOT OVERFILL. TO AVOID
SPILLING, DO NOT ADD INGREDIENTS PAST
THE “MAX LIQUID” LINE.
REMOVAL:
1 Turn the pitcher anticlockwise and then lift off
the motor base (I).
2 Depending on the consistency of the contents in
the pitcher, open the pour spout cap and use the
pour spout to empty the liquid contents.
3 For thicker consistencies, remove the lid and
blade assembly carefully (by the top of the
shaft), then empty the contents from the
pitcher. To remove the lid, press the release
button on the lid (J) and pull the handle up to a
90° angle. Lift the lid of f the pitcher.
4 Make sure the appliance is unplugged when not
inuse.
5 To release the motor base from the counter or
tabletop, place your fingers under the sides of
the black paddles on the sides of the base and
lift up to release suction cup feet (K).
9
Page 10
®
1.2 L PROCESSOR BOWL
or
A B C D E F
ASSEMBLY
If your unit comes with this accessory, read the following instructions. For a list of what is included with this model, refer to inside flap of the box.
G
CAUTION: CHOPPING BLADE IS
NOT LOCK ED IN PLACE. IF USING
THE POUR SPOUT, ENSURE THE
LID IS FULLY LOCKED ONTO THE
BLEND AND PREP BOWL.
ASSEMBLY OF
ASSEMBLY:
THE PROCESSOR
BOWL
NOTE: Ninja® Auto-iQ®
Technology can sense
which jar is on the motor
base. The function lights
will illuminate depending
on which container is
placed on the motor base.
10
IMPORTAN T: MAK E SURE THE MOTOR
1 Holding the desired blade by the top of the
NOTE: THE CHOPPING BL ADE WILL FIT
WARNING: NE VER LEAV E THE APPLIANCE
UNAT TENDED WHILE IN USE.
CAUTION: USE CAUTION WHEN
HANDLING THE CHOPPING BL ADE AS IT
IS VERY SHARP.
BASE IS PLUGGED IN FOR USE .
shaft, place it onto the drive gear
bowl. Ensure that the attachment is seated
properly and is standing upright.
LOOSELY ON THE DRIV E GEAR.
(A)
inside the
CAUTION: THE CHOPPING BLADE
IS NOT LOCKED IN PL ACE.
IF POURING WITH THE LID
REMOVED, ALWAYS REMOVE
THE CHOPPING BLADE FIRST.
2 Place the motor base on a clean, dry, level
surface such as a counter or tabletop. Press
down on the motor base to make sure that the
suction cups adhere to the counter or tabletop.
3 Align and lower the Processor Bowl
motor base. Handle should be aligned slightly to
the right of the LOCK symbol on the motor base.
4 Rotate the Processor Bowl clockwise (C) until
it locks in place (you will hear a click when the
lock is engaged).
5 The bowl can be placed on the motor base
two ways; the handle can be on the front right
corner
(D)
or the front lef t corner
(E)
(B)
.
onto the
IMPORTANT: DO NOT
OVERFILL. TO AVOID SPILLING,
DO NOT ADD INGREDIENTS
PAST THE “MAX” FILL LINE.
6 Add the ingredients to the bowl, making sure
they do not exceed the highest measured
marking line on the side of the bowl.
7 Holding the lid by the handle in the upright
position
(F)
the triangle ( ) located on the lid with the
triangle ( ) located on the bowl handle. Press
the handle down until you hear a click.
8 The triangles on the lid and the Processor Bowl
handle (G) MUST be aligned for the blender to
turn on.
9 Plug the power cord into the electrical outlet.
The function lights will illuminate.
, place it on top of the bowl aligning
Page 11
®
Chopping blade Dough blade
H I J K L
USE REMOVAL USE
If your unit comes with this accessory, read the following instructions. For a list of what is included with this model, refer to inside flap of the box.
CAUTION: CHOPPING BLADE IS
NOT LOCK ED IN PLACE. IF USING
THE POUR SPOUT, ENSURE THE
LID IS FULLY LOCKED ONTO THE
BLEND AND PREP BOWL.
USING THE
USING THE CHOPPING BLADE:
CHOPPING BLADE
& DOUGH BLADE
1 Holding the Chopping Blade assembly by the top
2 Add the ingredients and secure the bowl lid
3 Plug the power cord into the electrical outlet.
CAUTION: USE CAUTION WHEN
HANDLING THE CHOPPING BLADE AS THE
BLADES ARE VERY SHARP.
of the shaft (H), place it onto the gear shaf t inside
the bowl. Ensure that the attachment fits around
the gear shaft and that it is standing straight.
onto the bowl.
Once the bowl is engaged, the programs
available for that attachment will illuminate.
Select the program desired based on your recipe.
The Auto-iQ
automatically at the end of the program.
®
program will stop the appliance
CAUTION: THE CHOPPING BLADE
IS NOT LOCKED IN PL ACE.
IF POURING WITH THE LID
REMOVED, ALWAYS REMOVE
THE CHOPPING BLADE FIRST.
4 When you have reached your desired
consistency, stop the appliance by pressing the
START/STOP button or selecting the program
twice. Wait for the blade to stop turning.
REMOVAL:
5 To remove the lid, press the release button (I) on
the lid and pull the lid handle up to a 90° angle.
6 Turn the bowl anticlock wise and lift it to remove
it from the motor base (J).
7 Make sure that the motor base is unplugged
when not in use.
8 To release the motor base from the counter or
tabletop, place your fingers under the sides of
the black paddles on the sides of the base and
lift up to release suction cup feet (K).
1-877-646-5288
IMPORTANT: DO NOT
OVERFILL. TO AVOID SPILLING,
DO NOT ADD INGREDIENTS
PAST THE “MAX" FILL LINE.
USING THE DOUGH BLADE:
IMPORTANT: This makes 500g of dough at a time.
Do not overfill or exceed. Motor may overheat.
1 Holding the Dough Blade assembly by the top of
the shaft (L), place it onto the gear shaft inside
the bowl. Ensure that the attachment fits around
the gear shaft and that it is standing straight.
2 Add the ingredients and secure the bowl lid onto
the bowl.
3 Plug the power cord into the electrical outlet.
Press the START/STOP button to turn on the
unit. Once the bowl is engaged, the programs
available for that attachment will illuminate.
Select LOW on the control panel and process
until ingredients come together to form a mass.
4 Once finished making the dough, stop the appliance
by pressing the
selecting the program twice. Wait for the blade to
stop turning.
START/STOP
button again or
11
Page 12
®
CUTTING DISCS
If your unit comes with this accessory, read the following instructions. For a list of what is included with this model, refer to inside flap of the box.
ASSEMBLY OF
THE CUTTING
DISCS
12
ASSEMBLY:
WARNING: NE VER LEAV E THE APPLIANCE
UNATTENDED WHILE IN USE.
CAUTION: Cutting discs are sharp. W hen
handling the cutting discs, always hold by
the rim of cut ting discs and keep fingers
away from cut ting edges.
IMPORTAN T: MAK E SURE THE MOTOR
BASE IS PLUGGED IN FOR USE .
IMPORTAN T: Use only the LOW setting
when using either cutting disc.
NOTE: Cutting discs must be used with the
feed chute lid.
1 Place the motor base on a clean, dry, level
surface such as a counter or tabletop. Press
down on the motor base to make sure that the
suction cups adhere to the counter or tabletop.
2 Secure the bowl onto the motor base. Align and
lower the Processor Bowl onto the motor base.
Handle should be aligned slightly to the right of
the LOCK symbol on the motor base.
3 Rotate the Processor Bowl clock wise until it
locks in place (you will hear a click when the
lock is engaged).
4 Holding the spindle by the shaft, place it onto
the drive gear inside the bowl. Ensure that it is
seated properly and is standing upright.
5 Use the spindle hole to grasp the selected disc
and place it over the spindle.
6 The Slicing/Shredding disc is reversible. Use
the side labeled "Slicer" for slicing. Carefully flip
the disc over to the side labeled "Shredder" for
shredding.
7 Holding the Lid from the feed chute, place it on
top of the bowl and turn clockwise aligning the
arrow
( )
located on the lid with the arrow
located on the bowls handle.
8
Plug the power cord into the electrical outlet.
Select LOW on the control panel. The disc will
begin spinning.
9 Add the food that you want to slice, shred or
grate through the feed chute on the lid. Use
the two-part food pusher to help guide the
food through the feed chute. The middle piece
of the food pusher is removable to use for
smalleringredients.
10 The LOW setting will run for 30 seconds, or
when finished, press the START/STOP button
and wait for the disc to stop turning. Press the
button on the feed chute lid located near the
handle to unlock and turn the lid anticlockwise.
Lift to remove from the processor bowl. Using
the spindle hole, carefully lift the disc out of the
bowl and remove the spindle.
11 Make sure that the motor base is unplugged
when not in use.
12 To release the motor base from the counter or
( )
tabletop, place your fingers under the sides of
the black paddles on the sides of the base and
lift up to release suction cup feet.
Page 13
®
CARE &
MAINTENANCE
CLEANING:
CAUTION: MAKE SURE THAT THE
MOTOR BASE IS UNPLUGGED FROM THE
POWER SOURCE BEFORE INSERTING
OR REMOVING ANY ATTACHMENT AND
BEFORE CLEANING.
CAUTION: DO NOT IMMERSE THE MOTOR
BASE INTO WATER OR ANY OTHER
LIQUID.
CAUTION: HANDLE BL ADES CAREFULLY
AS THE BLADES ARE VERY SHA RP.
1 Separate/remove all par ts from each other.
2 Clean the motor base with a damp cloth and
wipe dr y.
NOTE: The Double Wall Stainless Steel Nutri
Ninja® Cup is NOT dishwasher safe.
3 Place the cups, lids, blade assemblies, discs,
pitcher, and bowl in the top rack of the
dishwasher.
OR
4 Carefully hand wash the cups, lids, blade
assemblies, discs, pitcher, and bowl in warm,
soapy water with a soft cloth.
NOTE: If the appliance needs servicing, please
call cus tomer service at 1- 877-646-5288.
STORING:
1 Store the Nutri Ninja Auto-iQ® Pro Compact
System upright. Secure the power cord on the
back of the base by wrapping the cord around
the cord wrap. Do not place anything on top
of the unit. Store the cups and the rest of the
attachments where they will not be damaged
and won’t cause a hazard.
RESETTING THE MOTOR
THERMOSTAT:
The
Nutri Ninja Auto-iQ Pro Compact System
features a safety system that prevents damage
to the unit’s motor and drive system should you
inadvertently overload the appliance. If the
appliance is overloaded, the motor will stop. To reset
the appliance, follow the resetting procedure below:
1 Unplug the appliance from the electrical outlet.
2 Remove and empty the cup/pitcher/bowl and
ensure that no food is jamming the cut ting
blades.
3 Allow the appliance to cool for approximately
30 minutes.
4 Re-install the cup/pitcher/bowl onto the
motor base and re-plug the appliance into the
electrical outlet.
5 Proceed with using the appliance as before
while making sure not to exceed the maximum
recommended capacities.
1-877-646-5288
13
Page 14
®
TROUBLESHOOTING
GUIDE
Unit doesn’t turn on:
• Make sure the unit is plugged in and the START/STOP button is pressed.
•Insertandrotatecupclockwiseinthebaseuntilitclicksintoplace.Displayshouldturnon.
Unit doesn’t turn off:
•Remove cup from base by rotating cup anticlockwise and lifting out. Display should turn off. Unplug the power cord from the outlet.
Lid/blade assembly hard to assemble:
•Set the cup on a level surface. Place the lid or blade assembly on the top of the cup and align the threads so that the lid/blades sit flat on the cup. Twist clockwise so
that the lid/blades evenly align to the cup until you have a tight seal.
Food is not evenly chopped:
•For best results when chopping, make sure all ingredients are as dry as possible. Cut pieces down to even sizes, and reduce the amount of food in the cup. Use the
Auto-iQ® CHOP button for best results.
Doesn’t mix well, food gets stuck:
•Using the Auto-iQ programs is the easiest way to achieve great results. The pulses and pauses allow the food to settle towards the blade. If food is routinely getting
stuck adding some liquid will usually help.
•Whenpackingthecups,startwithfreshitems,thenaddliquids,powders/dr yingredients,andnallyfrozenitemsorice.
Unit moves on the counter while blending:
•Makesurethesurfaceaswellasthefeetoftheunitarecleananddry.
Unit is difficult to remove from the counter for storage:
•Toreleasethemotorbasefromthecounterortabletop,placeyourhandsunderneathbothsidesofthemotorbaseandgentlypulltheunitupandtowardsyou.
SUGGESTED
RECIPE
14
PIZZA DOUGH
•7g packetactivedryyeast
•½tsp sugar
•150ml warmwater40.5-43°C(105-110°F)
•470g plainour
•1⁄ 3tsp salt
•60ml oliveoil
•reser vedour
•reser vedwater
DIRECTIONS
1. Combine the yeast, sugar, and warm water in a small bowl and set aside until foamy, about 5 minutes.
2. Place the dough blade attachment into the Processor Bowl and add the flour, salt, olive oil, and the yeast mixture. Blend for 30 seconds until dough comes
together. Remove the dough, form a ball, and place into a lightly oiled bowl. Cover loosely with plastic wrap and allow to rest and rise for 1 hour, until dough is
doubled in size.
Page 15
NOTES
®
1-877-646-5288
15
Page 16
NOTES
®
16
Page 17
NOTES
®
Auto-iQ,Euro-Pro,Ninja,Nutri-NinjaandSip&SealandareregisteredtrademarksofEuro-ProOperatingLLC.
Pro Extractor Blades is a trademark of Euro-Pro Operating LLC.
1-877-646-5288
17
Page 18
®
**THIS WARRANTY IS FOR ALL COUNTRIES EXCEPT GERMANY**
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1) year from the date of purchase when utilised for normal household use, subject
to the following conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This Limited Warranty does not cover normal wear of parts and does not
apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any
of its parts, which have been performed by a repair person not authorised by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For assistance
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to
cover the cost of return freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any,
is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to
anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete
address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as
damage in shipping is not covered by your Limited Warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.
PRODUCT REGISTRATION
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings
set forth in the accompanying instructions.
18
Page 19
®
**THIS WARRANTY IS FOR GERMANY ONLY**
TWO (2) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of two (2) years from the date of purchase when utilised for normal household use, subject
to the following conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This Limited Warranty does not cover normal wear of parts and does not
apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any
of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For assistance
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to
cover the cost of return freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is
limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone
of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete
address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as
damage in shipping is not covered by your Limited Warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.
PRODUCT REGISTRATION
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings
set forth in the accompanying instructions.
1-877-646-5288
19
Page 20
Euro -Pro Ope rating LL C
New ton, MA USA 0 2459
Ville St . Laurent , Québec Can ada
H4S 1A 7
BL4 92� INTL �30�15 0724 �1(NOGR INDER )
© 2015 Eur o-Pro Op erating LL C
Illust rations may d iffer fro m actual pro duct. We are c onstantl y striving t o
impro ve our produ cts, there fore the spe cificatio ns containe d herein are
subjec t to change wi thout noti ce.
Printed in China
1-877-646-5288
Loading...