Nilfisk Alto Poseidon 2 User Manual

Operating
instructions

POSEIDON 2

128330683 e (09.2015)
EN-DA-NO-SV-FI-DE-FR-NL-IT-ES-PT-EL-TR-CS-HU-PL

Instruktionsbog ............................................................. 3 - 21

Instruksjonsbok ..........................................................22 - 40

Instruktionsbok ........................................................... 41 - 60

Käyttöohje ..................................................................61 - 80

Instruction manual ......................................................81 - 99

Betriebsanleitung ..................................................... 100 - 120

Manuel d'Instructions ............................................... 121 - 142

Gebruikershandleiding ............................................. 143 - 163

Manuale di istruzioni ................................................ 164 - 184

Manual de Instrucciones .......................................... 185 - 205

Manual de Instruções ............................................... 206 - 226

γχειριδιο οδηγιων ..................................................... 227 - 248

Ýþletme kýlavuzu ..................................................... 249 - 270

Návod k obsluze....................................................... 271 - 289

Üzemeltetési útmutató ............................................. 290 - 309

Instrukcja obsługi ..................................................... 310 - 330

Copyright © 2015 Nilfisk-ALTO, Division of Nilfisk-Advance A/S

Contents

1 Introduction .................................................................................................. 4

1.1 Symbols used to mark instruction .......................................................................4

2 Safety precautions and working techniques ................................................4

3 Description ................................................................................................. 10

3.1 Application ........................................................................................................10

3.2 Operation elements and model survey .............................................................10

4 Before you start using your pressure washer ........................................ 11

4.1 Mounting of holders for spray lance ..................................................................11

4.2 Mounting of hose hook (only models without hose reel) .............................11

4.3 Mounting of hose reel handle (only models with hose reel) ..............................11

4.4 Mounting of quick coupling ...............................................................................12

4.5 Mounting of high pressure hose .......................................................................12

5 Operating your pressure washer ............................................................. 12

5.1 Connection of high pressure hose ....................................................................12

5.2 Mounting of spray lance ....................................................................................13

5.3 Water connection ..............................................................................................13

5.4 Telescopic handle .............................................................................................13

5.5 Start and stop of the machine (when connected to a water supply) .................14

5.6 Start the machine (when connected to open containers (suction mode)) ........14

5.7 Pressure regulation ...........................................................................................14

5.8 Operation with detergents .............................................................................15

5.9 Regulation of pressure / water volume .............................................................16

6 Fields of application and working methods ........................................... 16

6.1 General .............................................................................................................16

7 After using your pressure washer ........................................................... 17

7.1 Storing the washer ............................................................................................17

7.2 Winding up of electric cable and high pressure hose ......................................17

7.3 Storage of accessories .....................................................................................17

8 Maintenance ............................................................................................... 18

8.1 Cleaning of water inlet fi lter .............................................................................18

8.2 Cleaning of nozzle ............................................................................................18

8.3 Cleaning of machine vents ...............................................................................18

8.4 Greasing of couplings ......................................................................................18

9 Trouble-shooting ....................................................................................... 19

10 Further information ................................................................................... 20

10.1 Warranty conditions ........................................................................................20

11 Main Technical Data ................................................................................... 20

12 EU Declaration of Conformity ................................................................... 21

Original Instructions

3

1 Introduction

1.1 Symbols used to mark instruction

All pictograms attached to the high pressure washer and its components are shown and ex­plained in this manual.

Safety instructions marked with this symbol must be observed to prevent personal injury or
serious damage to property.

Caution where there is a risk of damaging the machine or its individual components.



This symbol indicates tips and instructions to simplify work and to ensure a safe operation of
the high pressure washer.

2 Safety precautions and working techniques

Before starting up your machine for the fi rst time, this instruction manual must be read through
carefully. Save the instructions for later use.

WARNING!

• Inhalation of aerosols can be hazardous to health.
Where applicable use a device in order to avoid or re­duce aerosols production, e.g., a shield covering the
nozzle. For protection against aerosols use a respira­tory mask of class FFP 2 or higher.

• The high water pressure generated by the machine
and the power connection are particular sources of
danger.

• Machines shall not be used by children or untrained
personnel. Children should be supervised to ensure
that they do not play with the machine.

• Do not use the machine within range of persons un­less they wear protective clothing.

• Before starting up your machine please check it care­fully for any defects. If you fi nd any, do not start up
your machine, contact your Nilfi sk distributor. The in­sulation of the electric cable should be faultless and
without any cracks. If the electric cable is damaged,
an authorized Nilfi sk di stributor should replace it.

• Always unplug the power plug before cleaning or
maintenance and when replacing parts or converting

4

Original instructions

the machine to another function.

• Observe the national safety regulations issued, for
example, by the employers liability insurance associa­tion, social security institutions, occupational safety
and health authorities or other organizations.

Accessories and spare parts

• To ensure the machine safety only use original spare
parts from Nilfi sk or approved by Nilfi sk.

• High pressure hoses, fi ttings and couplings are impor­tant for the safety of the machine. Only use hoses, fi t­tings and couplings recommended by Nilfi sk.

Physical, sensory or mental conditions



Applications

• This machine is not intended for use by persons
(including children) with reduced physical, senso­ry or mental capabilities or lack of experience and
knowledge. If the machine is used by people with re­duced physical, sensory or mental capabilities or lack
of experience and knowledge they shall have been
given supervision or instruction concerning use of the
machine in a safe way and understand the hazards in­volved.

This machine has been developed for domestic use
such as:

• Car, motorbike, boat, caravan, trailer, patio/drive/fl ag­stones, woodwork, brickwork, barbecue, garden furni­ture, lawn mower.

Any other use is considered as improper use. Nilfi sk
accepts no liability for any damage resulting from such
use. The risk for such use is borne solely by the user.
Proper use also includes proper operation, servicing
and repairs as specifi ed in this instruction.

Clothing and equipment

Always take action to protect yourself when operating
the machine.

5Original Instructions

• Wear shoes with non-slip soles.

• Wear goggles, ear protection and protective clothes
during operation.

Transporting the high pressure washer

• When transporting the machine in or on a vehicle, it



must be secured, e.g. with straps, so that it cannot slip
or tip over.

• Nilfi sk recommends that the machine is positioned
horizontally on the backside, when transported in or
on a vehicle.

Detergents

• This machine has been designed for use with clean­ing agents supplied or recommended by Nilfi sk. The
use of other cleaning agents or chemicals may ad­versely affect the function of the machine.

 Before starting the work



Electrical connection

Inspecting the machine

• Do not use the machine if a supply cord or important
parts of the machine are damaged, e.g., safety de­vice, high pressure hose, and spray handle and spray
attachments.

• The trigger of the spray handle must move easily and
automatically return to its starting position when re­leased.

• Always keep high pressure hose and spray attach­ment in good condition (clean, moving easily) and cor­rectly assembled.

WARNING!

Minimize the risk for electrical shock:

• Voltage and frequency of the machine (see rating
plate) must match the voltage of and frequency of the
mains supply.

• Only connect the machine to electrical installation
made by a certifi ed electrician and com ply with IEC

6

Original instructions

60364-1.

• It is recommended that the electrical supply to the
machine should include a residual current device that
will interrupt the supply if the leakage current to earth
exceeds 30 mA for 30 ms.

• Due to the high power consumption of the machine an
appropriate mains fuse is required.

• Inadequate extension cables can be dangerous. If an
extension cable is used, it shall be suitable for outdoor
use, and the connection has to be kept dry and off the
ground.

• Nilfi sk recommends use of an extension cable drum
when cable extension is needed which keeps the
socket at least 60 mm above the ground.

• If the electric cable is damaged, it must be replaced
by an authorized Nilfi sk distributor or similar qualifi ed
person in order to avoid a hazard.

• Connecting the high pressure washer to a supply
system, the max allowed impedance is = 0,4023 
(Zmax). Consult with the supply authority that the
equipment is connected only to a supply of that im­pedance or less.

Water connection

• This high pressure washer is only allowed to be con­nected with the drinking water mains, when an appro­priate backfl ow preventer has been installed, Type BA
according to EN 60335-2-79.

• The backfl ow preventer can be ordered under number

106411177.

• As soon as drinking water has fl own through the back­fl ow preventer, it is no longer regarded as drinking
water.

• Operation by suction (e.g. a rainwater vessel) is car­ried out without a backfl ow preventer – see “Connec-
ting to a pressureless water supply”. The machine
can be connected to water mains with a max. inlet­pressure of 1 MPa/10 bars and max. 60°C.

7Original Instructions

Safety devices

Locking device on spray handle:

• The spray handle features a locking device. When the
pawl is activated, the spray handle cannot be ope­rated.

Thermal sensor:

• A thermal sensor protects the motor against overload­ing. The machine will restart after a few minutes when
the thermal sensor has cooled.

Pressure safety device:

• An integrated hydraulic safety valve protects the
system from excessive pressure.

During work

WARNING!

• It is not allowed to clean asbestos-containing surfaces
with high pressure.

• Risk of explosion – Do not spray fl ammable liquids.

• Never draw in fl uids containing solvents (e.g., gaso­line, heating oil, paint thinner or acetone) These sub­stances damage the materials used in the machine.
Their spray is highly combustible, explosive and poi­sonous.

• Never direct the water jet at yourself, other persons,
not even to clean clothing or footwear - risk of injury.

• Never direct the water jet at pets or other animals.

• Never direct the water jet at live electrical equipment
or the machine itself - danger of short-circuiting.

• Hold the spray lance fi rmly with both hands. The spray
lance is affected by a thrust of up to 27.4 N and a sud­den torque when activating the trigger of the spray
handle during operation.

• Never start up a frozen machine. Frost damages are
not covered by the guarantee!

• Always ensure fi rm and safe footing.

• The machine shall be operated in an upright position.

• If the machine is left or not used for 5 minutes, it must
be switched off on the start/stop switch "O" (1).

8

Original instructions

After fi nishing the work

WARNING!

• Always switch off the machine and unplug the power
plug from the socket after work and when leaving the
machine unattended.

• Disconnect water inlet hose between machine and
water supply.

• Always empty pump, hose and accessories of water
after use of the machine and prior to storing.

Maintenance and repairs

WARNING!

• Always disconnect the electrical plug from the socket
prior to maintenance, cleaning and repair.

• Any repair should always be made in Nilfi sk autho­rized workshop with original Nilfi sk spare parts.

• Do not attempt any maintenance not described in the
instructions.

• If the machine refuses to start, stops, pulsates, pres­sure fl uctuates, motor busses, fuse blows or no wa­ter comes out, check the trouble shooting diagram
in these instructions. In case other problems occur,
please contact your local Nilfi sk distributor.

Recycling the high pressure washer

Make the old machine unusable immediately.

• Unplug the machine.

• Cut the electric cable.

Do not discard electrical appliances with household
waste. As specifi ed in WEEE Directive 2012/19/EC on
old electrical and electronic appliances, used electrical
goods must be collected separately and recycled eco­logically. Contact your local authorities or your nearest
dealer for further information.

9Original Instructions

3 Description

3.1 Application

3.2 Operation elements and
model survey

This high-pressure washer has
been developed for semiprofes­sional routine cleaning:

- Professional craftsman jobs,
cleaning of vehicles, boat,
caravan and minor cleaning
jobs within building and con­struction

Section 6 describes the use of
the high-pressure washer for
various cleaning jobs.

See illustration at the end of
this manual.

1 Start/stop switch
2 Water inlet (with fi lter)
3 High pressure connection

(only machines without

hose reel)
4 High pressure hose
5 Electric cable
6 Button for regulation of

pressure and water volume
7 Ergo 2000 spray handle

with lock (7a)
8 Flexopower Plus spray

lance (standard models)
9 4-in-1 spray lance (T and

XT models)

Only use the high-pressure
washer for purposes described
in this manual.

The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.

10 Detachable detergent con-

tainer
11 Nozzle cleaning tool
12 Dosing of detergents
13 Hose reel
14 Hose hook (only machines

without hose reel)
15 Model tag
16 Button for telescopic handle
17 Telescopic handle
18 Turnable cable hook

Specifi cations: See model tag
(15) of machine.

We reserve the right to alter the
specifi cations.

10

Original Instructions

4 Before you start using your pressure

washer

4.1 Mounting of holders for
spray lance

Mount the holders for spray
lance on the machine.

4.2 Mounting of hose hook
(only models without
hose reel)

4.3 Mounting of hose reel
handle (only models
with hose reel)

Mount the hose hook (14) on
the handle (2 screws).

Note: the hose hook can be
mounted on the front as well as
on the back. Front position is to
be used if the product is used
together with a special wall
hook for wall storage.

1. Click the hose reel handle
on to the trolley handle (no
screws).

11Original Instructions

4.4 Mounting of quick
coupling

1. Screw the quick coupling
tight on to the water inlet (2).

Note: The inlet fi lter must al­ways be fi tted in the water inlet
pipe to fi lter out major impuri­ties as these will damage the
pump valves.

Caution: Failure

to fi t the fi lter will

invalidate the

guarantee.



4.5 Mounting of high
pressure hose

Attach the high pressure hose
(4) to the spray handle (7).

5 Operating your pressure washer

5.1 Connection of high pres­sure hose

Machines without hose reel: At­tach the high pressure hose (4)
to the high pressure connection
of the machine (3).

12

Only max. 7 m additional exten­sion hose can be added.

Machines with hose reel: Un­wind the high pressure hose
completely.

Original Instructions

5.2 Mounting of spray lance 1. Pull the blue quick-release

A

B

NOTE!

Always remove any dirt from
the nipple before connecting
the spray lance to the spray
handle.

grip (A) of the spray gun
backwards.

2. Insert the nipple of the spray
lance (B) into the quick-re­lease connection and release
it.

3. Pull the spray lance (or other
accessory) forwards to check
that it is securely attached to
the spray gun.

5.3 Water connection An ordinary 1/2" garden hose of
min. 10 m and max. 25 m will

be suitable.

NOTE: Connec­tion to the public
mains according
to regulations.

IMPORTANT! Only use wa­ter without any impurities. If

there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi­tional fi lter should be mounted.

1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrat­ing the machine.

Note: Check
that the fi lter is

fi tted in the water
inlet pipe and that it is clean
and free from debris.

2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 60°C).

3. Turn on the water.

5.4 Telescopic handle

The machine features a tele­scopic handle. To raise or lower
the handle, press the button
(16) and move the handle up­wards or downwards. When a
click is heard, the handle is in
right position.

13Original Instructions

5.5 Start and stop of the ma­chine (when connected
to a water supply)

The spray lance is affected
by a thrust during opera­tion - therefore always hold it
fi rmly with both hands. IMPOR-

TANT: Point the nozzle at the
ground.

to the surface, which is to be
cleaned.

Do not cover the
machine during
operation.

5.6 Start the machine (when
connected to open con­tainers (suction mode))

1. Check that the machine is in
upright position.

NOTE: Do not place the ma-

chine in tall grass!

2. Release the trigger lock.

3. Activate the trigger of the
spray handle and let the wa­ter run until all air has es­caped from the high pressure
hose.

4. Turn the start/stop switch (1)
to position "I".

5. Activate the trigger of the
spray handle.

Always adjust the distance and
thus the pressure of the nozzle

The washer can take in water
from a rain water tank as an
example. The hose for the water
supply must not be too long,
approx. 5 m.

Make sure that the water tank is
not placed on a lower level than
the machine.

Use an external fi lter if the wa­ter contains impurities.

1. Make sure that the water
hose is fi lled completely with
water before connecting to
the machine. Place the entire

Note: If the machine is left or
not used for 5 minutes, it must
be switched off on the start/stop
switch "O" (1):

1. Turn the start/stop switch to
position "O".

2. Disconnect the electrical plug
from the socket.

3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.

4. Lock the spray handle.

When releasing the trigger of
the spray handle, the machine
automatically stops. The ma­chine will start again when you
re-activate the spray handle.

hose in a tank or bucket. To
avoid water spillage, crimp
the water inlet hose down in
the water and then connect
the hose to the machine with
the quick coupling and fi nally
uncrimp the water inlet hose.

2. Dismount spray handle,
lance and nozzle.

3. Turn the start/stop switch to
position "I" and let the water
run, until the air has escaped
from the water hose and the
pump.

4. Mount spray handle and
thereafter lance.

5.7 Pressure regulation Flexopower Plus spray lance

The pressure can be regulated
on the Flexopower Plus spray
lance.

High pressure

Low pressure / Detergent

14

Original Instructions

T and XT models:

4-in-1 spray lance

The pressure can be regulated
on the 2-in-1 spray lance.

Low Pressure / detergent

5.8 Operation with
detergents

20°

65°

Application of detergents is
NOT possible if an extension
hose is applied.

1. Fill the container with a de­tergent.

2. Mount the Flexopower Plus
spray lance and adjust it to
low pressure. Turn the 4-in-1
nozzle to pos Low Pressure/
Detergent (see section 5.7).

3. Adjust the dosing regulator
(12) to the re quired vol ume
of detergent (0-5%).

Tornado / high pressure

Wide angle / high pressure

Turbohammer / high pressure

4. Apply the detergent from
below and up wards.

5. Let the detergent act for the
time stated on the packing of
the detergent and fl ush with
pure water or use a brush.

External detergent container

1. Remove the cover with suc­tion hose from the detergent
container.

2. Mount the cover with suction
hose on the external deter­gent container.

The cover has a standard thread
and fi ts common detergent con­tainers. If your container does
not have a standard thread,
detach the fi lter from the suc­tion hose and remove the cover.
Remount the fi lter in the suction
hose.

Extra detergent hose can be
pulled out of the machine.

15Original Instructions

5.9 Regulation of pressure /
water volume

Working pressure and water
volume can be regulated on the
machine by turning the button
for regulation of pressure / wa­ter volume (6).

6 Fields of application and working

methods

6.1 General Effi cient high pressure cleaning is achieved by following a few

guidelines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly cho­sen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.

6.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the

chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface be­ing cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surfac that has to be cleaned can be da maged.

6.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical

effect may be required. Special wash brushes offer this supplemen­tary effect that removes stubborn dirt, traffi c fi lm or the like.

16

Original Instructions

7 After using your pressure washer

7.1 Storing the washer The machine should be sto-

red in a frost-free room!

Pump, hose and accessories
should always be emptied of
water prior to storing as follows:



7.2 Winding up of electric
cable and high pressure
hose

1. Stop the machine (turn the
start/stop switch (1) to posi­tion “O” and detach water
hose and accessory.

2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
handle.

3. Stop the machine and un­plug. Wind the electric cable
round the hooks placed on
the side of the machine.

4. Separate spray handle and
spray lance.

To avoid accidents, the electric
cable and the high pressure
hose should always be wound

5. Machines without hose reel:
Detach high pres sure hose,
coil it up and place it on the
hose storage.

Machines with hose reel: Coil

the high pressure hose up on
the hose reel.

6. Place spray handle, nozzles
and other ac ces so ries in the
holders of the machine.

Should the machine by mistake
be frozen, let it thaw and check
it for damage.

NEVER START-UP A FROZEN
MACHINE.

Frost damages are not
covered by the guarantee!

up carefully.

1. Wind up the electric cable on
the dedicated hooks. Built-in
clip for good holding.

The lower hook can be

turned to release the electric
cable.

7.3 Storage of accessories

2. The high pressure washer
comes in two models: A) with
hook for storage of high pres­sure hose (14) - B) with a
hose reel (13).

The standard accessories
(spray handle, spray lance
(A) and nozzle cleaning tool)
can be stored on the pressure
washer.

A

17Original Instructions

8 Maintenance

8.1 Cleaning of water inlet
fi lter

WARNING! Always disconnect

the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:

 Wash off water hose, high

pressure hose, spray lance
and accessories before
mounting.

 Clean the connectors of dust

and sand.

 Clean the nozzles.

Any repair should always be
made in an authorized work­shop with original spare parts.

Clean the water inlet fi lter regu­larly once a month or more fre­quently according to use. Care­fully loosen the fi lter with a pair
of pliers and clean it. Check that
it is intact before re-mounting it.

The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out various impurities,
as they will damage the pump
valves.

CAUTION: Failure to fi t the fi lter
will invalidate the guarantee.

8.2 Cleaning of nozzle A clogging up in the nozzle

causes a pump pressure which
is too high. This is why cleaning
is required immediately.

1. Stop the machine and dis­connect the nozzle.

2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!

3. Flush the nozzle backwards
with water.

8.3 Cleaning of machine
vents

8.4 Greasing of couplings To ensure easy connection and

The machine should be kept
clean so as to let cooling air

that o-rings do not dry up, the

pass freely through the ma­chine vents.

couplings should be greased
regularly.

18

Original Instructions

9 Trouble-shooting

Please ensure that you check the following before contacting the Nilfi sk-ALTO service organization:

Symptom Cause Recommended action

Machine refuses to start Machine not plugged in Plug in machine.

Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the extension cable.

Fluctuating pressure Pump sucking air Check that hoses and connections are air-
tight.
Valves dirty, worn out Clean and replace or refer to local Nilfi sk-
or stuck ALTO distributor
Pump seals worn out Clean and replace or refer to local Nilfi sk-
ALTO distributor.

Motor busses Low voltage or Activate the trigger of the spray handle.
low temperature

Machine stops Fuse has blown Replace fuse. Switch off other machines.
Incorrect mains voltage Check that the mains voltage corresponds
to specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool
down.
Nozzle partially blocked Clean the nozzle (see section 7.2)

Fuse blows Fuse too small Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.

Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until
regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds to
mains water specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Nozzle partially blocked Clean the nozzle (see section 7.2)
Water fi lter blocked Clean the fi lter (see section 7.1)
Hose kinked Straighten out hose.

Machine often starts Contact your nearest Nilfi sk-ALTO Service
and stops by itself Centre.

Spray handle is leaking Replace seat/ball/O-ring in the valve of the
spray handle.

Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen

No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 7.1)
Nozzle blocked Clean the nozzle (see section 7.2)

Pump pressure drops Button for regulation of Adjust the button to correct working pres-
pressure / water volume not sure.
correctly adjusted

In case problems other than the above occur, please contact your local Nilfi sk-ALTO distributor.

19Original Instructions

10 Further information

10.1 Warranty conditions Our general conditions of busi-

ness are applicable with regard
to the guarantee.

11 Main Technical Data

Type

Rated pressure

Cleaning impact

Water flow

Voltage/phase/fre­quency/current

Max. water temp.

bar/MPa

kg/force

Qmax/

QIEC

l/min

V/-/Hz/A

°C

POSEIDON

69/6.9 120/12 120/12 140/14 140/14 150/16 150/15 150/15

gallon

120/1/

POSEIDON

2-20

2 2.2 2.2 2.5 2.5 2.9 2.9 2.9

-/2.4

60/15

60 60 60 60 60 60 60 60

2-22 T

8.6/7.8 8.6/7.8 10.2/9.0 10.2/9.0 10.2/9.5 10.2/9.5 10.2/9.5

230/1/

50/10

POSEIDON

2-22 XT

230/1/

50/10

POSEIDON

2-25 XT

230/1/

50/12.6

Subject to change as a result of
technical advances.

POSEIDON

2-25 P

230/1/

50/12.6

POSEIDON

2-29

230/1/

50/14.5

POSEIDON

2-29 (KR)

230/1/

60/14.5

POSEIDON

2-29 XT

230/1/

50/14.5

Cable m55555555

Pump Rev./min 3400 2800 2800 2800 2800 2800 3400 2800

Nozzle size

Sound pressure level

Guaranteed sound
power level

Vibration according
to ISO 5349-1

Weight kg 28.1 27.1 27.1 28.1 28.1 28.1 26.3 28.1

1/8"

dB(A)

dB(A)

m/s

0.475 0.350 0.350 0.370 0.370 0.370 0.370 0.370

77.4 76.1 76.1 77.4 77.4 73.5 79.7 79.7

92 91 91 92 92 88 94 94

2

< 2.5 < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 < 2.5

20

Original Instructions

12 EU Declaration of Conformity

We,

Nilfi sk A/S
Kornmarksvej 1
DK-2605 Broendby
DENMARK

Hereby solely declare, that the product:

Product Description Type

HPW - Consumer 120 / 230 V 1~, 50 / 60 Hz,

IPX5

Is in compliance with the following standards:

Id and Version Title

EN 60335-1:2012 Household and similar electrical appliances - Safety - Part 1:

General requirements

EN 60335-2-79:2012 Household and similar electrical appliances - Safety - Part 2-79:

Particular requirements for high pressure cleaners and steam
cleaners

EN 55014-1:2006+A1:2009
+A2:2011

EN 55014-2:1997+A1:2001
+A2:2008

EN 61000-3-2:2006+A1:2009
+A2:2009

EN 61000-3-11:2000 Electromagnetic compatibility (EMC) - Part 3-11: Limits - Limita-

EN 50581:2012 Technical documentation for the assessment of electrical and

EMC - Requirements for household appliances, electric tools
and similar apparatus - Part 1: Emission

EMC - Requirements for household appliances, electric tools
and similar apparatus - Part 2: Immunity - Product family stan­dard

EMC - Part 3-2: Limits - Limits for harmonic current emissions
(equipment input current ≤ 16 A per phase)

tion of voltage changes, voltage fl uctuations and fl icker in public
low-voltage supply systems, for equipment with rated current ≤
75 A per phase and subject to conditional connection

electronic products with respect to restriction of hazardous
substances

Poseidon 2-20, 2-22 T, 2-22 XT,
2-25 XT, 2-25 P, 2-29, 2-29 XT

Following the provisions of:

Machinery Directive 2006/42/EC
EMC Directive 2004/108/EC
RoHS Directive 2011/65/EC
Noise Emission Directive 2000/14/EC – Conformity assessment procedure according to Annex V.
Measured noise level: 73-80 dB(A); Guaranteed noise level: 88-94 dB(A)

Hadsund 07-09-2015 Anton Sørensen

Senior Vice President – Global Operations
R&D – Vacuum Cleaners and High Pressure Washers

Place Date Name, Title Signature

21Original Instructions

http://www.nilfi sk.com

HEAD QUARTER

DENMARK

Nilfi sk A/S
Banemarksvej 58
DK-2605 Broendby
Tel.: [phone]
Website: www.nilfi sk.com

SALES COMPANIES

ARGENTINA

Nilfi sk srl.
Edifi cio Central Park
Herrera 1855, 6th fl oor/604
Ciudad de Buenos Aires
Tel.: [phone]
Website: www.nilfi sk.com.ar

AUSTRALIA

Nilfi sk Pty Ltd
Unit 1/13 Bessemer Street
Blacktown NSW 2148
Tel.: [phone]
Website: www.nilfi sk.com.au

AUSTRIA

Nilfi sk GmbH
Metzgerstrasse 68
5101 Bergheim bei Salzburg
Tel.: [phone]
Website: www.nilfi sk.at

BELGIUM

Nilfi sk n.v-s.a.
Riverside Business Park
Boulevard Internationalelaan 55
Bâtiment C3/C4 Gebouw
Bruxelles 1070
Tel.: [phone]
Website: www.nilfi sk.be

BRAZIL

Nilfi sk do Brasil
Av. Eng. Luis Carlos Berrini, 550
40 Andar, Sala 03
SP - 04571-000 Sao Paulo
Tel.: [phone]
Website: www.nilfi sk.com.br

CANADA

Nilfi sk Canada Company
240 Superior Boulevard
Mississauga, Ontario L5T 2L2
Tel.: [phone]
Website: www.nilfi sk.ca

CHILE

Nilfi sk S.A. (Comercial KCS Ltda)
Salar de Llamara 822
8320000 Santiago
Tel.: [phone]
Website: www.nilfi sk.cl

CHINA

Nilfi sk
4189 Yindu Road
Xinzhuang Industrial Park
201108 Shanghai
Tel.: [phone]
Website: www.nilfi sk-cs.com

CZECH REPUBLIC

Nilfi sk s.r.o.
VGP Park Horní Počernice
Do Čertous 1/2658
193 00 Praha 9
Tel.: [phone]
Website: www.nilfi sk.cz

DENMARK

Nilfi sk Danmark A/S
Industrivej 1
Hadsund, DK-9560
Tel.: [phone]
Website: www.nilfi sk.dk

FINLAND

Nilfi sk Oy Ab
Koskelontie 23 E
02920 Espoo
Tel.: [phone]
Website: www.nilfi sk.fi

FRANCE

Nilfi sk SAS
26 Avenue de la Baltique
Villebon sur Yvette
91978 Courtabouef Cedex
Tel.: [phone]
Website: www.nilfi sk.fr

GERMANY

Nilfi sk GmbH
Guido-Oberdorfer-Straße 2-10
89287 Bellenberg

Tel.: (+49) (0)7306/72-444
Website: www.nilfi sk.de

GREECE

Nilfi sk A.E.

Αναπαύσεως 29

Κορωπί Τ.Κ. 194 00

Tel.: [phone]
Website: www.nilfi sk.gr

HOLLAND

Nilfi sk B.V.
Versterkerstraat 5
1322 AN Almere
Tel.: [phone]
Website: www.nilfi sk.nl

HONG KONG

Nilfi sk Ltd.
2001 HK Worsted Mills
Industrial Building
31-39, Wo Tong Tsui St.
Kwai Chung, N.T.
Tel.: [phone]
Website: nilfi sk.com

HUNGARY

Nilfi sk Kft.
II. Rákóczi Ferenc út 10
2310 Szigetszentmiklós-Lakihegy
Tel.: [phone]
Website: www.nilfi sk.hu

INDIA

Nilfi sk India Limited
Pramukh Plaza, ‘B’ Wing, 4th fl oor, Unit No. 403
Cardinal Gracious Road, Chakala
Andheri (East) Mumbai 400 099
Tel.: [phone]
Website: www.nilfi sk.in

IRELAND

Nilfi sk
1 Stokes Place
St. Stephen’s Green
Dublin 2
Tel.: [phone]
Website: www.nilfi sk.ie

ITALY

Nilfi sk SpA
Strada Comunale della Braglia, 18
26862 Guardamiglio (LO)
Tel.: (+39) (0) 377 414021
Website: www.nilfi sk.it

JAPAN

Nilfi sk Inc.
1-6-6 Kita-shinyokohama, Kouhoku-ku
Yokohama, 223-0059
Tel.: [phone]
Website: www.nilfi sk.com

MALAYSIA

Nilfi sk Sdn Bhd
Sd 33, Jalan KIP 10
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Tel.: [phone]
Website: www.nilfi sk.com

MEXICO

Nilfi sk de Mexico, S. de R.L. de C.V.
Pirineos #515 Int.
60-70 Microparque
Industrial WSantiago
76120 Queretaro
Tel.: (+52) (442) 427 77 00
Website: www.nilfi sk.com

NEW ZEALAND

Nilfi sk Limited
Danish House
6 Rockridge Avenue
Penrose, Auckland 1061
Tel.: [phone]
Website: www.nilfi sk.com.au

NORWAY

Nilfi sk AS
Bjørnerudveien 24
1266 Oslo
Tel.: [phone]
Website: www.nilfi sk.no

PERU

Nilfi sk S.A.C.
Calle Boulevard 162, Of. 703, Lima 33- Perú
Lima
Tel.: [phone]
Website: www.nilfi sk.com

POLAND

Nilfi sk Sp. Z.O.O.
Millenium Logistic Park
ul. 3 Maja 8, Bud. B4
05-800 Pruszków
Tel.: [phone]
Website: www.nilfi sk.pl

PORTUGAL

Nilfi sk Lda.
Sintra Business Park
Zona Industrial Da Abrunheira
Edifi cio 1, 1° A

P2710-089 Sintra

Tel.: [phone]
Website: www.nilfi sk.pt

RUSSIA

Nilfi sk LLC
Vyatskaya str. 27, bld. 7/1st
127015 Moscow
Tel.: [phone]
Website: www.nilfi sk.ru

SINGAPORE

Den-Sin
22 Tuas Avenue 2
639453 Singapore
Tel.: [phone]
Website: www.densin.com

SLOVAKIA

Nilfi sk s.r.o.
Bancíkovej 1/A
SK-821 03 Bratislava
Tel.: [phone]
Website: www.nilfi sk.sk

SOUTH AFRICA

WAP South Africa
12 Newton Street
Spartan 1630
Tel.: [phone]
Website: www.wap.com.za

SOUTH KOREA

Nilfi sk Korea
3F Duksoo B/D, 317-15
Sungsoo-Dong 2Ga
Sungdong-Gu, Seoul
Tel.: [phone]
Website: www.nilfi sk.co.kr

SPAIN

Nilfi sk S.A.
Torre d’Ara,
Passeig del Rengle, 5 Plta. 10
08302 Mataró
Tel.: [phone]
Website: www.nilfi sk.es

SWEDEN

Nilfi sk AB
Taljegårdsgatan 4
431 53 Mölndal
Tel.: [phone]
Website: www.nilfi sk.se

SWITZERLAND

Nilfi sk AG
Ringstrasse 19
Kircheberg/Industri Stelz
9500 Wil
Tel.: [phone]
Website: www.nilfi sk.ch

TAIWAN

Nilfi sk Ltd
Taiwan Branch (H.K)
No. 5, Wan Fang Road
Taipei
Tel.: [phone]
Website: www.nilfi sk.tw

THAILAND

Nilfi sk Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Ladyao, Jatuchak, Bangkok 10900
Tel.: [phone]
Website: www.nilfi sk.co.th

TURKEY

Nilfi sk A.S.
Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7
Ümraniye, 34775 Istanbul
Tel.: [phone]
Website: www.nilfi sk.com.tr

UNITED ARAB EMIRATES

Nilfi sk Middle East Branch
SAIF-Zone
P.O. Box 122298
Sharjah
Tel.: (+971) (0) 655-78813
Website: www.nilfi sk.com

UNITED KINGDOM

Nilfi sk Ltd.
Nilfi sk House, Bowerbank Way
Gilwilly Industrial Estate, Penrith
Cumbria CA11 9BQ
Tel: (+44) (0) 1768 868995
Website: www.nilfi sk.co.uk

UNITED STATES

Nilfi sk Inc.
14600 21st Avenue North
Plymouth, MN-55447
Tel.: [phone]
Website: www.nilfi sk.com

VIETNAM

Nilfi sk Vietnam
No. 51 Doc Ngu Str.
P. Vinh Phúc, Q.Ba Dinh
Hanoi
Tel.: [phone]
Website: www.nilfi sk.com

a