Nikon MOTORMESH 4300 User Manual
MOTOMESH DUO 2.0
MOTOROLA
4300 Users Guide
July 2007
MOTOMESH DUO 2.0 4300 Users Guide
This page intentionally left blank.
July 2007
ii
Copyrights
The Motorola products described in this document may include copyrighted Motorola computer programs. Laws in the United
States and other countries reserve for Motorola certain exclusive rights for copyrighted computer programs. Accordingly, any
copyrighted Motorola computer programs contained in the Motorola products described in this document may not be copied or
reproduced in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products
shall not be deemed to grant either directly or by implication, estoppels or otherwise, any license under the copyrights, patents or
patent applications of Motorola, except for the normal nonexclusive, royalty-free license to use that arises by operation of law in
the sale of a product.
Disclaimer
Please note that certain features, facilities and capabilities described in this document may not be applicable to or licensed for use
on a particular system, or may be dependent upon the characteristics of a particular mobile subscriber unit or configuration of
certain parameters. Please refer to your Motorola contact for further information.
Trademarks
Motorola, the Motorola logo, and all other trademarks identified as such herein are trademarks of Motorola, Inc. All other
product or service names are the property of their respective owners.
Copyrights
© 2007 Motorola, Inc. All rights reserved. No part of this document may be reproduced, transmitted, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, without the prior written permission of
Motorola, Inc.
July 2007
iii
MOTOMESH DUO 2.0 4300 Users Guide
This page intentionally left blank.
July 2007
iv
Table
of
Contents
Contents
.............................................
.
.
.
.
Chapter 1: Product Introduction ............................................................................1-1
Infrastructure Devices...................................................................................................................................... 1-2
Infrastructure Devices within a MOTOMESH Wireless Network .......................................................................1-2
MOTOMESH Duo 4300 Device Specifications .............................................................................................. 1-4
Chapter 2: Infrastructure Device Installation........................................................2-1
Software Requirements......................................................................................................................................... 2-1
MeshManager EMS ......................................................................................................................................... 2-1
Web Interface Utility........................................................................................................................................ 2-2
Hardware Installation Notes ................................................................................................................................. 2-2
Ports and Connections...................................................................................................................................... 2-3
Operator Supply List........................................................................................................................................ 2-3
Optional Antennas .........................................................................................................................................................2-3
MOTOMESH DUO Infrastructure Device Labels........................................................................................... 2-4
Infrastructure Device MAC Address Table ..............................................................................................................2-5
Infrastructure Device Assembly....................................................................................................................... 2-6
Infrastructure Device Deployment and Installation.......................................................................................... 2-7
Grounding Considerations .............................................................................................................................................2-8
Assembling an AC Power MOTOMESH Duo Device...................................................................................................2-8
Assembling a DC Power MOTOMESH Duo Device ....................................................................................................2-9
Device Connectivity Testing..........................................................................................................................................2-9
Chapter 3: Device Configuration ............................................................................3-1
Pre-staging a MOTOMESH Duo 4300 Device in MeshManager......................................................................... 3-1
Default Device Configuration.......................................................................................................................... 3-1
Configuring a 4300 Device Mesh from 2.4 to 4.9, 5.4, or 5.8.......................................................................... 3-1
Demoting an IAP Device to a MWR.................................................................................................................. 3-13
Second IP Stack Aids in Troubleshooting .......................................................................................................... 3-15
Second IP Stack Settings................................................................................................................................ 3-15
Accessing the MOTOMESH Duo Device Recovery Settings in MeshManager..........................................................3-15
Device Recovery Settings............................................................................................................................................3-16
Chapter 4: License Information..............................................................................4-1
Motorola End User License Agreement................................................................................................................ 4-1
Third Party Licensing Agreements....................................................................................................................... 4-7
July 2007
v
MOTOMESH DUO 2.0 4300 Users Guide
Hostapd - Copyright and License Information................................................................................................. 4-7
Chapter 5: Customer Service .................................................................................5-1
Customer Service Information.............................................................................................................................. 5-1
Obtaining Support............................................................................................................................................ 5-2
System Information........................................................................................................................................................5-2
Return Material Request ................................................................................................................................................5-2
Radio Products and Services Division ...........................................................................................................................5-2
Radio Products and Services Division Telephone Numbers.....................................................................................5-2
Returning System Components to Motorola..................................................................................................................5-3
Returning FREs..............................................................................................................................................................5-3
Chapter 6: Certification and Safety Information...................................................6-1
FCC Regulatory Information................................................................................................................................ 6-1
Federal Communications Commission (FCC) Statement ................................................................................ 6-1
Safety Information for the MOTOMESH Products.............................................................................................. 6-2
FCC Radiation Exposure Statement................................................................................................................. 6-2
Safety Certification............................................................................................................................................... 6-2
Regulatory Requirements for CEPT Member States ............................................................................................ 6-3
European Union Notification ........................................................................................................................... 6-4
Belgium Notification........................................................................................................................................ 6-5
Luxembourg Notification................................................................................................................................. 6-5
Czech Republic Notification ............................................................................................................................ 6-5
Equipment Disposal ......................................................................................................................................... 6-5
EU Declaration of Conformity for RoHS Compliance......................................................................................... 6-6
CMM Labeling and Disclosure Table................................................................................................................... 6-8
Software License Terms and Conditions.............................................................................................................. 6-9
July 2007
vi
List
of
Figures
List of Figures
.............................................
.
.
.
.
Figure 1-1 MOTOMESH Duo 4300 Device Attached to a Light Pole..................................................1-1
Figure 1-2 IAP and MWR Devices in Context of a MOTOMESH Network ........................................1-3
Figure 2-1 MOTOMESH DUO 4300 - 49 AC and DC Device Product Labels (Samples)...................2-4
Figure 2-2 MOTOMESH DUO 4300 - 58 AC and DC Device Product Labels (Samples)...................2-4
Figure 2-3 MOTOMESH DUO 4300 - 54 AC and DC Device Product Label......................................2-4
Figure 2-4 Infrastructure Device Top View showing External Connection Points ...............................2-6
Figure 2-5 External Personality Plugs (Black, Grey, Red, or none) ......................................................2-6
Figure 2-6 Side View (B) of the 4300 Device’s External Connection Points........................................2-7
Figure 2-7 Side View (A) of the 4300 Device’s External Connection Points .......................................2-7
Figure 3-1 The Add New MOTOMESH Duo Device Panel in MeshManager .....................................3-2
Figure 3-2 Entering the 802.11 AP Ethernet MAC Address in MeshManager .....................................3-2
Figure 3-3 Selecting the Probe Button in MeshManager.......................................................................3-3
Figure 3-4 Examining Initial Device Defaults in MeshManager...........................................................3-4
Figure 3-5 Enabling the 802.11 a Radio on a 4300-54 and 4300-58 Device.........................................3-5
Figure 3-6 Enabling the 802.11 a Radio on a 4300-49 Device..............................................................3-5
Figure 3-7 An Example of a License Key Text File ..............................................................................3-6
Figure 3-8 Copying the License Key from the Text File .......................................................................3-6
Figure 3-9 Pasting the License Key into MeshManager........................................................................3-7
Figure 3-10 Entering 802.11 a Membership VLAN Data ...................................................................3-8
Figure 3-11 Configuring a Device to be an IAP or WR......................................................................3-9
Figure 3-12 Entering a Device Name ..................................................................................................3-9
Figure 3-13 Entering an Optional Deployed Location ......................................................................3-10
Figure 3-14 Adding a Device to the Mesh.........................................................................................3-10
Figure 3-15 After Adding a Device to the Mesh ...............................................................................3-11
Figure 3-16 After Successfully Adding a Device to the Mesh..........................................................3-12
Figure 3-17 Selecting an IAP Device to be Demoted........................................................................3-13
Figure 3-18 Promote / Demote Dialog ..............................................................................................3-14
Figure 3-19 Demoted IAP Device shown moved into a MWR Group..............................................3-14
July 2007
vii
List of Figures
This page intentionally left blank.
July 2007
viii
List
of
Tables
List of Tables
.............................................
.
.
.
.
Table 1-1 MOTOMESH Duo 4300-49 Device Specifications.............................................................1-4
Table 1-2 MOTOMESH Duo 4300-58 Device Specifications.............................................................1-5
Table 1-3 MOTOMESH Duo 4300-54 Device Specifications.............................................................1-7
Table 2-1 Recommended Antennas for Infrastructure Devices............................................................2-3
Table 2-2 MAC Address Table.............................................................................................................2-5
July 2007
ix
List of Tables
This page intentionally left blank.
July 2007
x
List
of
Procedures
List of Procedures
.............................................
.
.
.
.
Procedure 2-1 Assembling an AC Power MOTOMESH Duo Device................................................2-8
Procedure 2-2 Assembling a DC MOTOMESH Duo Device.............................................................2-9
Procedure 2-3 Testing Infrastructure Device Connectivity ................................................................2-9
Procedure 3-1 Configuring a 4300 Device Mesh................................................................................3-2
Procedure 3-2 Demoting an IAP to a MWR.....................................................................................3-13
Procedure 3-3 Accessing the MOTOMESH Duo Device Recovery Settings...................................3-15
July 2007
xi
List of Procedures
This page intentionally left blank.
July 2007
xii
Chapter
1
Chapter 1: Product Introduction
.............................................
.
.
.
.
This guide will provide you with technical specifications, installation guidelines, and testing
procedures for the MOTOMESH Duo 4300 infrastructure devices.
Figure 1-1 MOTOMESH Duo 4300 Device Attached to a Light Pole
July 2007
1-1
Product Introduction
Infrastructure Devices
The MOTOMESH DUO 4300 device is configured to operate as an Intelligent Access Point (IAP)
from the factory. The device is capable of being configured to operate as either an IAP or a MWR
(Mesh Wireless Router). The selection of an IAP or MWR configuration will be determined by the
customer’s wireless network needs at the time of purchase.
When the MOTOMESH Duo 4300 device is configured to operate as an IAP, it acts as the transition
point from the wireless network to the wired core network and from there, through media gateways,
out to the Internet. When the MOTOMESH Duo 4300 device is configured to operate as a MWR, it
behaves as a wireless device that is primarily deployed to seed and extend the range between IAPs and
Wireless Clients while simultaneously increasing the spectral efficiency of the network. While running
as a MWR device, the device’s Ethernet connector can be utilized to connect to another IP-enabled
device. This allows a network of IP-enabled devices (such as a camera) to be directly addressed,
accessed and managed over the MOTOMESH network.
IAP functionality includes:
• Transition Point between the wired and wireless network
• Dynamic Route Selection
MWR functionality includes:
• Dynamic Route Selection
• Range Extension for all other network devices
Infrastructure Devices within a MOTOMESH Wireless Network
.............................................
.
.
A MOTOMESH Duo 4300 device is considered a fixed Infrastructure device that can be configured
to operate as either an IAP (Intelligent Access Point) or a MWR (Mesh Wireless Router) within the
MOTOMESH Wireless Network. Infrastructure devices provide area coverage access for wireless
clients to the wired network.
July 2007
1-2
MOTOMESH DUO 2.0 4300 Users Guide
Figure 1-2 IAP and MWR Devices in Context of a MOTOMESH Network
Wireless Switch
Wireless
MWR
802.11
802.11
IAP
802.11
802.11
(MeshManager)
EMS
MWR
RADIUS
GEO
802.11
CA
July 2007
1-3
Product Introduction
MOTOMESH Duo 4300 Device Specifications
The following specification tables apply to the MOTOMESH Duo 4300-49, 4300-58, and 4300-54
Infrastructure Devices.
Table 1-1 MOTOMESH Duo 4300-49 Device Specifications
Radio Characteristics
Primary Radio Operating Freq. (GHz) 2.400 to 2.483
Secondary Radio Operating Freq. (GHz) 4.940 to 4.990
Wi-Fi Support 802.11b/g at 2.4GHz; 802.11a at 4.9GHz
RF Modulation CCK (802.11b) / OFDM (802.11a/g)
Transmit Power (Maximum) 35 dBm EIRP 34 dBm EIRP
Receive Sensitivity 801.11b: -92 dBm (at 11 Mbps)
Power Control 1dB increments
Antenna Type Two (2) omni directional, 8 dBi (for 2.4 GHz Radio) and 11 dBi (for 4.9
Antenna Connector N-Type
Routing
Routing Engine MeshConnex™ Layer 2 routing with Layer 1 situational-awareness
Routing Protocol Patented, hybrid proactive/reactive routing (low latency & fast route
IEEE 802.11s Support Upgradeable to IEEE 802.11s standard via OTA software updates
Network
Network Management Software MeshManager Element Management System via secure SNMP v.3
Network Interface 10/100Mbps Ethernet (RJ-45) port with surge suppression
2.4 GHz Portion 4.9 GHz Portion
802.11a: -77 dBm (at 27 Mbps) to -93
to -100 dBm (at 1 Mbps)
801.11g: -78 dBm (at 54 Mbps)
to -95 dBm (at 6 Mbps)
GHz Radio)
convergence)
dBm (at 3 Mbps)
Network Segmentation
Quality of Service (QoS) 802.11e, EDCF, 802.11p and the IP precedence of DSCP (ToS) bits
Security
Virtual LAN (VLAN) Supports up to sixteen (16) per node, or 4094 per network
Client Encryption Support WEP, WPA (TKIP) and WPA2 (AES, 802.11i)
Internodal Encryption Intra-Mesh Security
Authentication 802.1X (Infrastructure/Client) and MAC address hardware authentication
July 2007
Multiple SSIDs with VLAN mapping
1-4
MOTOMESH DUO 2.0 4300 Users Guide
Power
Power Input 90-264 VAC (with +/- 20% variation at 47 to 63 Hz)
12V +/- 10% VDC input, certified LPS power supply (orderable option)
Power Connector AC power cord, 12 ft
Power Consumption 15W (with both radios operating)
22.2W (with Canopy® Connect PoE operational)
29.4W (with IEEE 802.3af Standard PoE device)
Power over Ethernet (PoE) Canopy and IEEE 802.3af support available
Physical
Dimensions 9”x 6”x 3.5” (23.1cm x 15.2cm x 8.9cm)
Weight 4.5 lbs (2.04kg)
Packaging Outdoor, all-weather enclosure (NEMA 4)
Mounting 3” (7.62cm) diameter post mounting
Environment
Temperature Range -30 to +60 °C
Humidity 0 to 95%, non-condensing
Certifications FCC Part 15 & 90, UL, CSA
Available Options
Mounting Lamp post mount bracket assembly
Power AC photo cell adapter
Table 1-2 MOTOMESH Duo 4300-58 Device Specifications
Radio Characteristics
Primary Radio Operating Freq. (GHz) 2.400 to 2.483
Secondary Radio Operating Freq. (GHz) 5.725 to 5.825
Wi-Fi Support 802.11b/g at 2.4GHz; 802.11a at 5.8GHz
RF Modulation CCK (802.11b) / OFDM (802.11a/g)
2.4 GHz Portion 5.8 GHz Portion
Transmit Power (Maximum) 35 dBm EIRP 34 dBm EIRP
Receive Sensitivity 801.11b: -92 dBm (at 11 Mbps)
to -100 dBm (at 1 Mbps)
801.11g: -78 dBm (at 54 Mbps)
802.11a: -77 dBm (at 54 Mbps) to -93
dBm (at 6 Mbps)
to -95 dBm (at 6 Mbps)
Power Control 1dB increments
July 2007
1-5
Product Introduction
Antenna Type Two (2) omni directional, 8 dBi (for 2.4 GHz Radio) and 10 dBi (for 5.8
GHz Radio)
Antenna Connector N-Type
Routing
Routing Engine MeshConnex Layer 2 routing with Layer 1 situational-awareness
Routing Protocol Patented, hybrid proactive/reactive routing (low latency & fast route
convergence)
IEEE 802.11s Support Upgradeable to IEEE 802.11s standard via OTA software updates
Network
Network Management Software MeshManager Element Management System via secure SNMP v.3
Network Interface 10/100Mbps Ethernet (RJ-45) port with surge suppression
Network Segmentation
Multiple SSIDs with VLAN mapping
Quality of Service (QoS) 802.11e, EDCF, 802.11p and the IP precedence of DSCP (ToS) bits
Security
Virtual LAN (VLAN) Supports up to sixteen (16) per node, or 4094 per network
Client Encryption Support WEP, WPA (TKIP) and WPA2 (AES, 802.11i)
Internodal Encryption Intra-Mesh Security
Authentication 802.1X (Infrastructure/Client) and MAC address hardware authentication
Power
Power Requirements 90-264 VAC (with +/- 20% variation at 47 to 63 Hz)
12V +/- 10% VDC input, certified LPS power supply (orderable option)
Power Connector AC power cord, 12 ft
Power Consumption 15W (with both radios operating)
22.2W (with Canopy® Connect PoE operational)
29.4W (with IEEE 802.3af Standard PoE device)
Power over Ethernet (PoE) Canopy and IEEE 802.3af support available
Physical
Dimensions 9”x 6”x 3.5” (23.1cm x 15.2cm x 8.9cm)
Weight 4.5 lbs (2.04kg)
Packaging Outdoor, all-weather enclosure (NEMA 4)
Mounting 3" (7.62cm) diameter post mounting
Environment
Temperature Range -30 to +60 °C
Humidity 0 to 95%, non-condensing
Certifications FCC Part 15 & 90, UL, CSA
July 2007
1-6
MOTOMESH DUO 2.0 4300 Users Guide
Available Options
Mounting Lamp post mount bracket assembly
Power AC photo cell adapter
Table 1-3 MOTOMESH Duo 4300-54 Device Specifications
Radio Characteristics
Primary Radio Operating Freq. (GHz) 2.400 to 2.483
Secondary Radio Operating Freq. (GHz) 5.470 to 5.725
Wi-Fi Support 802.11b/g at 2.4GHz; 802.11a at 5.4GHz
RF Modulation CCK (802.11b) / OFDM (802.11a/g)
2.4 GHz Portion 5.4 GHz Portion
Output Power (Maximum) 35 dBm EIRP 34 dBm EIRP
Receive Sensitivity 801.11b: -92 dBm (at 11 Mbps)
to -100 dBm (at 1 Mbps)
801.11g: -78 dBm (at 54 Mbps)
802.11a: -77 dBm (at 54 Mbps) to -93
dBm (at 6 Mbps)
to -95 dBm (at 6 Mbps)
Power Control 1dB increments
Antenna Type Two (2) omni directional, 8 dBi (for 2.4 GHz Radio) and 10 dBi (for 5.4
GHz Radio)
Antenna Connector N-Type
Routing
Routing Engine MeshConnex Layer 2 routing with Layer 1 situational-awareness
Routing Protocol Patented, hybrid proactive/reactive routing (low latency & fast route
convergence)
IEEE 802.11s Support Upgradeable to IEEE 802.11s standard via OTA software updates
Network
Network Management Software MeshManager Element Management System via secure SNMP v.3
Network Interface 10/100Mbps Ethernet (RJ-45) port with surge suppression
Network Segmentation
Multiple SSIDs with VLAN mapping
Quality of Service (QoS) 802.11e, EDCF, 802.11p and the IP precedence of DSCP (ToS) bits
Security
Virtual LAN (VLAN) Supports up to sixteen (16) per node, or 4094 per network
Client Encryption Support WEP, WPA (TKIP) and WPA2 (AES, 802.11i)
Internodal Encryption Intra-Mesh Security
Authentication 802.1X (Infrastructure/Client) and MAC address hardware authentication
July 2007
1-7
Product Introduction
Power
Power Requirements 90-264 VAC (with variation at 47 to 63 Hz)
12V +/- 10% VDC input, certified LPS power supply (orderable option)
Power Connector AC power cord, 12 ft
Power Consumption 15W (with both radios operating at 50% duty cycle)
Power over Ethernet (PoE) Support for Canopy PoE connection
Physical
Dimensions 9”x 6”x 3.5” (23.1cm x 15.2cm x 8.9cm)
Weight 4.5 lbs (2.04kg)
Packaging Outdoor, all-weather enclosure (NEMA 4)
Mounting 3" (7.62cm) diameter post mounting
Environment
Temperature Range -30 to +60 °C
Humidity 0 to 95%, non-condensing
Certifications FCC Part 15 & 90, UL, CSA
Available Options
Mounting Lamp post mount bracket assembly
Power AC photo cell adapter
July 2007
1-8
Chapter
2
Chapter 2: Infrastructure Device Installation
.............................................
.
.
This chapter will provide hardware and software installation information for the MOTOMESH DUO
4300 Infrastructure Device.
Software Requirements
.............................................
.
.
The MOTOMESH DUO 4300 infrastructure devices can be setup and configured using the
MeshManager Element Management System (EMS) or the Web Interface utility.
MeshManager EMS
MeshManager EMS is used for device setup, configuration, and management of MOTOMESH
infrastructure devices. Prior to using the MeshManager software for device installation and
configuration, ensure that it is installed and running on a network computer. MeshManager will be
used during the device setup process to validate the installation of the device(s) as well as manage,
within the wireless network.
Detailed information about the MeshManager application is found in the MeshManager Users Guide.
If you are using MeshManager to manage your network, there are some additional
guidelines to be observed when using the Web Interface.
1. When using the following MeshManager elements:
• VAP Manager
• VLAN Manager
July 2007
• Security Manager
2-1
Chapter 2: Infrastructure Device Installation
DO NOT use the Web Interface to manage VAP, VLAN, or Security
configurations.
2. If a device has already been added to the network using MeshManager, DO NOT
use the Web Interface to change the device type from an IAP to an MWR or from
an MWR to an IAP.
3. If you use the Web Interface to restore the factory defaults for the device, you
must first delete the device and add it again using MeshManager so that the device
type will be properly identified in the database.
Web Interface Utility
Initial configuration and management of MOTOMESH infrastructure devices can also carried out
using the Web Interface utility. The Web Interface application is designed to support the setup and
configuration of smaller MOTOMESH networks. It can be used as an alternative to the MeshManager
during the initial setup and configuration of MOTOMESH infrastructure devices. The application uses
standard elements of a Web-based interface to allow the user to configure the basic parameters of
seven primary network management elements required to successfully deploy a MOTOMESH network
using the navigation menu displayed on each page.
Detailed information about the Web Interface utility can be found in the Web Interface Users Guide.
Hardware Installation Notes
.............................................
.
.
For a MOTOMESH deployment, a permanent power source for each MOTOMESH Duo 4300 device
must be provided. All infrastructure devices require professional installation to ensure that the
installation is performed in accordance with FCC licensing regulations
Infrastructure devices are fitted with a single pivot mounting bracket designed to be attached to light
poles and other probable installation sites. Alternate mounting hardware is available for mounting
directly to posts or structures that are too large for the standard bracket. Optional remote antenna
mount hardware is also available for use with the alternate mounting hardware.
July 2007
2-2
Ports and Connections
The following list defines the standard ports and connections for the MOTOMESH Duo 4300 device
running in either the IAP or MWR modes.
• 100-240V A/C Power Cable with flying leads
• One non Power over Ethernet (PoE) Ethernet port
• One Power over Ethernet (PoE) capable port supporting:
o Canopy Connect PoE
o Standards based 802.3af PoE
IAPs can be pre-configured to use Canopy Connect PoE or 802.11 Standards
Based PoE or with POE Disabled.
• Optional External Personality Plug to activate power over Ethernet Motorola Canopy ™
PoE or standards based 802.3af PoE.
MOTOMESH DUO 2.0 4300 Users Guide
• Mounting Bracket
Operator Supply List
The Network Operator must supply the following equipment:
• Mounting Location
• Power Source (100-240 VAC depending on IAP configuration)
• Ethernet connection between the IAP and MiSC.
Optional Antennas
The following antennas are recommended for use with Infrastructure Devices.
Table 2-1 Recommended Antennas for Infrastructure Devices
Manufacturer
Radiall-Larsen R380.700.212 10 dBi 5.8 GHz Infrastructure
Radiall-Larsen R380.500.227 11 dBi 4.9 GHz Infrastructure
Part Number Gain Usage
July 2007
2-3
Loading...