Nikon MONARCH 7 XRT Riflescope Instruction Manual

In the event that you should require service for your Nikon RIFLESCOPE, in case of USA market, please send it directly to: Nikon Scope Service 841 Apollo Street, Suite 100 El Segundo, CA. 90245-4721 1-800-Nikon SV. In other market, please bring it to dealer from which you purchased it.

2.5-10×50 SF 4-16×50 SF

Instruction manual

Manufacturer:

3-25, Futaba 1-chome, Shinagawa-ku, Tokyo 142-0043, Japan

Printed in the Philippines (783C)3E/1406

TABLE OF CONTENTS

1. Introduction ....................................................................... 3

2. Nomenclature ................................................................... 5

3. Speciﬁ cations ................................................................... 7

4. Instructions ....................................................................... 8

5. Obtaining and changing the custom XR turret................ 12

1. Introduction

Congratulations on your choice of a Nikon MONARCH 7 Riflescope. Your new scope is the finest example of Nikon's rugged and durable construction and precision bright optics; important qualities for a serious shooter's riflescope. Whether you use your scope for hunting or for target shooting, the procedure for mounting is identical. A set of high-quality steel mounting rings which have a standard diameter of 30 mm (1.18 in) are required to mount the scope. Follow the ring manufacturer's instructions for mounting procedures. After mounting the scope on your rifle, follow the procedures for reticle alignment.

About the Custom XR Turret

The Custom XR Turret provides simplicity in long range shooting by providing an elevation turret engraved to match the ballistics of your cartridge, allowing you to dial the distance to the target. Bullet Drop Compensation is now as simple as dialing the distance on your turret, eliminating the need to hold over your target for long shots.

IMPORTANT INFORMATION

IT IS IMPORTANT THAT YOUR NIKON RIFLESCOPE IS MOUNTED PROPERLY AND THAT CAREFUL CONSIDERATION BE GIVEN WHEN MOUNTING YOUR NIKON RIFLESCOPE ON A FIREARM. WE HIGHLY RECOMMEND THAT YOUR NIKON RIFLESCOPE BE MOUNTED ON YOUR FIREARM BY AN EXPERIENCED, REPUTABLE GUNSMITH. THE USER ASSUMES ALL RESPONSIBILITY AND LIABILITY FOR HAVING THE NIKON RIFLESCOPE PROPERLY MOUNTED TO A FIREARM AND USING THE NIKON RIFLESCOPE PROPERLY. ALWAYS CHECK THE CONDITION OF YOUR MOUNTING SYSTEM PRIOR TO USING YOUR FIREARM.

SUPPLIED ITEM(S)

Body ················································1 piece High pro le turret ·····································1 piece Cleaning cloth·················································································1 piece

Objective cap ( ip open) ················ 1 piece High pro le turret cap ······························1 piece Hex key for Custom XR Turret (1.3mm) ·········································1 piece Eyepiece cap ( ip open) ················· 1 piece Sunshade ··················································1 piece

Caution

(1) Do NOT look at the sun through the riflescope. It will permanently damage your eye. This precaution applies to all optical devices, such as cameras and binoculars. (2) The riflescope is effectively sealed against moisture and dust. You may use your scope safely either in the rain or in dusty climates. To preserve the appearance of the scope, we recommend that it be dried and

cleaned prior to storage. Use a soft cloth for cleaning metal surfaces and use photographic lens tissue to clean the scope's lenses.

When setting the reticle for hunting, you should determine your standard range and then adjust the reticle based upon that target distance. For targets which vary from that standard distance, according to personal preference, you may simply adjust the position of the reticle in relation to your target, or you may wish to use the procedure for trajectory compensation. We hope that you will enjoy your new Nikon riflescope for many years to come. Enjoy using it, and above all, always follow safe shooting procedures.

N.B. Export of the products* in this manual may be controlled under the laws and relatives of the exporting country. Appropriate export procedure, such as obtaining of export license, shall be required in case of export. *Products: Hardware and its technical information (including software)

2. Nomenclature

2.5-10×50 SF 4-16×50 SF

Fig. 2-1

1 Objective lens 2 Eyepiece lens 3 Elevation adjustment turret 4 Windage adjustment turret 5 Eyepiece adjustment 6 Power index 7 Power scale 8 Power selector ring 9 Diopter index dot 0 Side focus adjustment turret a Distance scale b Distance index c Sunshade

+ 7 hidden pages