Page 1
En
Wireless Mobile Utility (Android)
User’s Manual
Install the Wireless Mobile Utility on your smart device (smartphone or tablet) to download pictures from a camera or take
pictures remotely.
The Wireless Mobile Utility supports the following cameras.
Some feature built-in Wi-Fi, while others require an optional
wireless mobile adapter. See the section for your camera for
more information on using the Wireless Mobile Utility.
D600, D7100, D5200
A
D3200, COOLPIX A
B
Nikon 1: V2, J3, S1
C
COOLPIX: P520, P330, S9500, S6500, S5200,
D
AW110
Save where otherwise noted, the camera illustrations in this
manual show the D3200.
A Trademark Information
Wi-Fi is a registered trademark of the Wi-Fi Alliance. GOOGLE PLAY
is a trademark of Google Inc. All other trade names mentioned in
this manual are the trademarks or registered trademarks of their
respective holders.
0 2–26
0 27–51
0 52–74
0 75–97
1
Page 2
D600, D7100, D5200
A
This section describes the options available when the Wireless
Mobile Utility and an optional wireless mobile adapter are used
to connect to D600, D7100, and D5200 cameras.
Features
Use the Wireless Mobile Utility to:
Take pictures remotely (0 6): Tap the shutter icon in the Wireless Mobile Utility to
take pictures and download them to
the smart device.
Download pictures as they are taken (0 9):
Take pictures with the camera and save
them to the smart device.
View pictures (0 11): View the pictures stored on the smart device or
the camera memory card.
Download pictures (0 15): Download existing pictures from the camera memory card.
Share pictures (0 18): Share pictures via e-mail or upload pictures to
photo-sharing sites.
For information on inserting the adapter, see page 4.
A
2
Page 3
Notices
• No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form without Nikon’s prior written permission.
• Nikon reserves the right to change the specications of the hardware and software described in this manual at any time and
without prior notice. Nikon will not be held liable for damages
that may result from any mistakes that this manual may contain.
System Requirements
Before installing the Wireless Mobile Utility, conrm that your
smart device meets the following system requirements:
OS
Wireless LAN 11b/g/n
Screen resolution 800 × 480 pixels (WVGA) or higher
D Using This Application for the First Time
You must accept the terms and conditions of the End User License
Agreement (EULA) before connecting.
• Smartphone: Android 2.3 series, Android 4.x series
• Tablet: Android 3.x series, Android 4.x series
A
3
Page 4
Installing the App
Locate the app on Google Play.
1
Connect to Google Play on the smart device and search for
“Wireless Mobile Utility”.
Install the app.
2
Install the Wireless Mobile Utility.
Establishing a Wireless Connection
Connect the wireless mobile adapter.
1
Attach the wireless mobile adapter to the camera and turn
the camera on. See the manual supplied with the wireless
mobile adapter for details.
Ready the smart device.
2
Select Wi-Fi settings > WPS button connection. The smart
device will wait for a signal from the camera.
Press the WPS button.
3
Press the WPS button on the wireless mobile adapter for
about 5 s until the LED on the wireless mobile adapter ashes red and green.
Launch the Wireless Mobile Utility.
4
When a connection is established, the LED on the wireless
mobile adapter will glow green and the main dialog for the
Wireless Mobile Utility will be displayed on the smart device. For information on taking pictures, see page
formation on viewing pictures, see page
11.
6. For in-
A
4
Page 5
A WPS
WPS (Wi-Fi Protected Setup) is a standard designed to make it easy
to establish a secure wireless network. For information on the steps
involved and the length of time the smart device will wait for a connection, see the documentation supplied with the smart device.
A Manual Wireless Connections
Display Wi-Fi settings for the smart device.
1
Select the mobile adapter SSID (the default SSID begins with
2
“Nikon_WU_”). The LED will light green when a connection is
established.
D The Wireless Mobile Adapter
While the adapter is inserted, the camera exposure meters will not
turn off; monitor the camera battery level to ensure that the camera does not power off unexpectedly. In addition, some camera
menu items may be grayed out and unavailable and the camera
can not be used for playback or live view. Movie recording can
not be used.
A
5
Page 6
Taking Photos
Take pictures remotely from the smart device, or take pictures
with the camera and save them to the smart device.
Remote Photography
Follow the steps below to take photos from the smart device.
Tap Take photos.
1
The camera viewnder will go dark and the smart device
will display the view through the camera lens.
Focus.
2
In normal- and wide-area AF AF-area modes, tap the subject
in the display to focus (if subject-tracking AF is selected, the
camera will focus using wide-area AF).
A
6
Page 7
Tap the shutter icon.
3
The shutter will be released after you
remove your nger from the icon; the
resulting photo is rst saved to the camera memory card and then downloaded
to the smart device. There is no need to
point the smart device at the wireless
mobile adapter.
D Remote Photography
Remote photography ends automatically when the battery in the
camera or smart device runs low. Note that using remote photography for an extended period may cause the camera’s internal
temperature to rise; if necessary, remote photography will end automatically to minimize damage to camera circuits.
The smart device can not be used to adjust camera settings; use
camera controls to adjust settings before starting Step 1. Regardless of the release mode selected with the camera, only one picture
will be taken each time you tap the shutter icon. Note that the
display may not update smoothly depending on the device and
network conditions.
A shutter speed of “Time” is available in mode M. Choose a shutter speed of A on the camera and select remote photography
mode on the smart device, then tap the shutter icon to open the
shutter. Shooting ends when the icon is tapped again.
A
7
Page 8
A The Remote Photography Display
Mode selec tion: Tap to select photo
capture mode (page 9).
Settings: The following photographyrelated options can be accessed from
the smart device menu:
• Live view: Turn the live view display
on or off.
• Remote shooting auto download:
Choose whether to download pictures
to the smart device after shooting (remote shooting mode only).
• Self-timer: If ON is selected, the camera shutter will be released 2 s after
you tap the shutter icon. The timer
turns off automatically after the shutter is released.
Self-timer icon: Displayed when the selftimer is on.
Camera settings: Shutter speed, aperture,
etc. Not displayed when device is in
landscape orientation.
Thumbnail area: Downloaded pictures.
A
8
Page 9
Downloading Photos as They Are Taken
Take photos with the camera and save them to the smart device.
Tap Take photos.
1
Tap .
2
The dialog shown below at right will be displayed (page
10).
A
9
Page 10
Take photos.
3
Frame photos in the camera viewnder and shoot. Photos
are downloaded to the smart device after being saved to
the camera memory card.
A The Photo Capture Display
The photo capture display is shown below.
Mode selection: Tap to select remote
shooting mode (page 6).
Thumbnail area: Downloaded pictures.
A
10
Page 11
Viewing Photos
Tap View photos to view the pictures stored on the smart device. You can also view the pictures on the camera memory card
and download selected images to the smart device.
Viewing Pictures
View the pictures in camera memory or on the smart device.
Tap View photos.
1
A
11
Page 12
Choose a device.
2
Tap Pictures on camera to view the pictures on the camera
memory card, Pictures on smart device to view the pictures
stored on the smart device. The pictures will be displayed
as small “thumbnail” images (in some cases, a folder list may
be displayed; tap a folder to view the pictures it contains).
View pictures.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to view additional pictures.
A
12
Page 13
A The Full-Frame Display
The full-frame display is shown below.
Return to shooting
mode (available only
if display was accessed
by tapping thumbnail
Tap picture to hide or
view icons
Zoom in or out
D Movies
Movies can not be viewed using the Wireless Mobile Utility, but
movies can be played back by tapping the movie or playback icon
in the thumbnail list to display a list of movie apps and choosing
an app from the list.
in shooting display)
A
13
Page 14
A Folders
Downloaded pictures are stored in folders with names consisting
of “C” (for new photos downloaded during shooting) or “D” (for existing pictures downloaded during playback) followed by the date,
an underscore, and a 3-digit folder number. A new folder is created
each time you launch the Wireless Mobile Utility and either capture new photos or download existing pictures. To view pictures in
other folders, tap the folder icon at the top of the display and tap a
folder to display its contents.
On the smart device, the path to folders created for new photos
downloaded during shooting is “/sdcard/Nikon_WU/Capture”, while
the path to those created for existing pictures downloaded during
playback is “/sdcard/Nikon_WU/Card”.
A
14
Page 15
Downloading Existing Pictures
Download pictures from the camera memory card.
Tap View photos.
1
Tap Pictures on camera.
2
Tap Pictures on camera to view the pictures on the camera.
A
15
Page 16
Select pictures for download.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to display the desired picture and
tap the check mark to select or deselect.
Press the back button on the smart device to return to the thumbnail list.
Alternatively, you can select multiple
pictures by touching and holding a
thumbnail until check boxes are displayed at the top right corner of each
picture and then tapping thumbnails
to select or deselect. You can also tap
Select all in the smart device menu to
select all images or Deselect all to deselect all images.
Tap Download.
4
Tap Download to download the selected pictures.
A
16
Page 17
A Folders
To select all images in a folder, tap the folder icon at the top of the
display and then touch and hold the folder in the folder list.
D Dropped Connections
If the wireless connection is lost while a picture is being downloaded, the picture will not be saved to the smart device (connection
loss may occur if, for example, the camera turns off during download). Any pictures downloaded before the connection was interrupted are unaffected.
A
17
Page 18
Sharing Pictures
Before sharing pictures, connect to a network with Internet access.
zz
Sharing Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Share.
2
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
A
18
Page 19
zz
Sharing Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to share until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Share.
3
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
A
19
Page 20
A Sharing Folders
To share all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be shared by
tapping Share as described in Step 3.
A
20
Page 21
Deleting Pictures
Downloaded pictures can be deleted from the smart device one
at a time or in groups. The Wireless Mobile Utility can not be
used to delete pictures from the camera memory card.
zz
Deleting Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Delete.
2
Tap Delete.
A conrmation dialog will be displayed;
tap Yes.
A
21
Page 22
zz
Deleting Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to delete until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Delete.
3
A conrmation dialog will be displayed;
tap Yes.
A
22
Page 23
A Deleting Folders
To delete all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be deleted by
tapping Delete as described in Step 3.
A
23
Page 24
Wireless Mobile Utility Options
The smart device menu for the Wireless Mobile Utility home display can be used to access the options listed below.
Settings
Option Description
Synchronize clock
Battery options
Image size
Thumbnails
App auto launch
Choose whether to synchronize the camera clock with
the smart device.
Remote photography will end automatically when the
camera or smart device battery reaches the selected
level.
Choose whether pictures are resized for download to
the smart device. Select Original to download images
at their original size.
Choose the size of the thumbnails in the playback display.
If ON is selected, the Wireless Mobile Utility will launch
automatically when the smart device detects a signal
from the wireless mobile adapter.
A
24
Page 25
Option Description
Wireless Mobile
Adapter settings
SSID
Authentication/
encryption
Password
Channel Choose the wireless channel used by the network.
Auto power-o
delay
Advanced
settings
Current settings View current wireless mobile adapter settings.
Format settings Tap Yes to restore default settings.
Language
Adjust network settings for the wireless mobile adapter.
Choose an SSID for the wireless mobile adapter. The
smart device displays the SSID when you connect to
the network manually.
Choose the authentication method used for connection
to the network.
Enter a password. The password type is selected using
Advanced settings > Password entr y: choose ASCII for an
8- to 63-character alphanumeric password, HEX for a 64digit hexadecimal password.
Choose the delay before the wireless mobile adapter
enters sleep when there is no wireless connection.
• WPS PIN: Set the wireless mobile adapter WPS PIN.
• WPS mode: Select the adapter WPS mode.
• Password entry: Choose the password type.
• Sub-net mask: Enter a subnet mask.
• DHCP server IP address: Enter the wireless mobile adapt-
er IP address.
• DHCP client IP address: Enter the smart device IP address.
Choose the language in which the user interface for the
Wireless Mobile Utility is displayed.
A
25
Page 26
Info
Option Description
Camera The name of the camera currently connected.
Wireless Mobile
Adapter
Link speed View the transmission rate.
Serial number View the product serial number.
Firmware version View the current firmware version.
App
Exit
Exit the Wireless Mobile Utility.
View information about the wireless mobile adapter.
Select About to view Wireless Mobile Utility version information, Check for updates to connect to
the Google Play service and check for updates, or
License Terms and Conditions to view the terms of use
for this application.
A
26
Page 27
D3200, COOLPIX A
B
This section describes the options available when the Wireless
Mobile Utility and an optional wireless mobile adapter are used
to connect to D3200 and COOLPIX A cameras.
Features
Use the Wireless Mobile Utility to:
Take pictures remotely (0 31): Tap the shutter icon in the Wireless Mobile Utility to
take pictures and download them to
the smart device.
Download pictures as they are taken (0 34):
Take pictures with the camera and save
them to the smart device.
View pictures (0 36): View the pictures stored on the smart device or
the camera memory card.
Download pictures (0 40): Download existing pictures from the camera memory card.
Share pictures (0 43): Share pictures via e-mail or upload pictures to
photo-sharing sites.
For information on inserting the adapter, see page 29.
B
27
Page 28
Notices
• No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form without Nikon’s prior written permission.
• Nikon reserves the right to change the specications of the hardware and software described in this manual at any time and
without prior notice. Nikon will not be held liable for damages
that may result from any mistakes that this manual may contain.
System Requirements
Before installing the Wireless Mobile Utility, conrm that your
smart device meets the following system requirements:
OS
Wireless LAN 11b/g/n
Screen resolution 800 × 480 pixels (WVGA) or higher
D Using This Application for the First Time
You must accept the terms and conditions of the End User License
Agreement (EULA) before connecting.
• Smartphone: Android 2.3 series, Android 4.x series
• Tablet: Android 3.x series, Android 4.x series
B
28
Page 29
Installing the App
Locate the app on Google Play.
1
Connect to Google Play on the smart device and search for
“Wireless Mobile Utility”.
Install the app.
2
Install the Wireless Mobile Utility.
Establishing a Wireless Connection
Connect the wireless mobile adapter.
1
Attach the wireless mobile adapter to the camera and turn
the camera on. See the manual supplied with the wireless
mobile adapter for details.
Ready the smart device.
2
Select Wi-Fi settings > WPS button connection. The smart
device will wait for a signal from the camera.
Press the WPS button.
3
Press the WPS button on the wireless mobile adapter for
about 5 s until the LED on the wireless mobile adapter ashes red and green.
Launch the Wireless Mobile Utility.
4
When a connection is established, the LED on the wireless
mobile adapter will glow green and the main dialog for the
Wireless Mobile Utility will be displayed on the smart device. For information on taking pictures, see page
formation on viewing pictures, see page
36.
31. For in-
B
29
Page 30
A WPS
WPS (Wi-Fi Protected Setup) is a standard designed to make it easy
to establish a secure wireless network. For information on the steps
involved and the length of time the smart device will wait for a connection, see the documentation supplied with the smart device.
A Manual Wireless Connections
Display Wi-Fi settings for the smart device.
1
Select the mobile adapter SSID (the default SSID begins with
2
“Nikon_WU_”). The LED will light green when a connection is
established.
D The Wireless Mobile Adapter
While the adapter is inserted, the camera exposure meters will not
turn off; monitor the camera battery level to ensure that the camera does not power off unexpectedly. In addition, some camera
menu items may be grayed out and unavailable and the camera
can not be used for playback or live view. Movie recording can
not be used.
B
30
Page 31
Taking Photos
Take pictures remotely from the smart device, or take pictures
with the camera and save them to the smart device.
Remote Photography
Follow the steps below to take photos from the smart device.
Tap Take photos.
1
The camera viewnder will go dark and the smart device
will display the view through the camera lens.
Tap the shutter icon.
2
Tap the shutter icon. If the camera is able
to focus, the shutter will be released
after you remove your nger from the
icon; the resulting photo is rst saved
to the camera memory card and then
downloaded to the smart device. There
is no need to point the smart device at
the wireless mobile adapter.
B
31
Page 32
D Remote Photography
Remote photography ends automatically when the battery in the
camera or smart device runs low. Note that using remote photography for an extended period may cause the camera’s internal
temperature to rise; if necessary, remote photography will end automatically to minimize damage to camera circuits.
The smart device can not be used to adjust camera settings; use
camera controls to adjust settings before starting Step 1. Regardless of the release mode selected with the camera, only one picture
will be taken each time you tap the shutter icon. Note that the
display may not update smoothly depending on the device and
network conditions.
In normal- and wide-area AF AF-area modes, the camera will focus
on the subject in the focus area selected with the camera; if subjecttracking AF is selected, the camera will focus using wide-area AF.
B
32
Page 33
A The Remote Photography Display
Mode selec tion: Tap to select photo
capture mode (page 34).
Settings: The following photographyrelated options can be accessed from
the smart device menu.
• Remote shooting auto download:
Choose whether to download pictures
to the smart device after shooting (remote shooting mode only).
• Self-timer: If ON is selected, the camera shutter will be released 2 s after
you tap the shutter icon. The timer
turns off automatically after the shutter is released.
Self-timer icon: Displayed when the selftimer is on.
Camera settings: Shutter speed, aperture,
etc. Not displayed when device is in
landscape orientation.
Thumbnail area: Downloaded pictures.
B
33
Page 34
Downloading Photos as They Are Taken
Take photos with the camera and save them to the smart device.
Tap Take photos.
1
Tap .
2
The dialog shown below at right will be displayed (page 35).
B
34
Page 35
Take photos.
3
Frame photos in the camera viewnder and shoot. Photos
are downloaded to the smart device after being saved to
the camera memory card.
A The Photo Capture Display
The photo capture display is shown below.
Mode selection: Tap to select remote
shooting mode (page 31).
Thumbnail area: Downloaded pictures.
B
35
Page 36
Viewing Photos
Tap View photos to view the pictures stored on the smart device. You can also view the pictures on the camera memory card
and download selected images to the smart device.
Viewing Pictures
View the pictures in camera memory or on the smart device.
Tap View photos.
1
B
36
Page 37
Choose a device.
2
Tap Pictures on camera to view the pictures on the camera
memory card, Pictures on smart device to view the pictures
stored on the smart device. The pictures will be displayed
as small “thumbnail” images (in some cases, a folder list may
be displayed; tap a folder to view the pictures it contains).
View pictures.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to view additional pictures.
B
37
Page 38
A The Full-Frame Display
The full-frame display is shown below.
Return to shooting
mode (available only
if display was accessed
by tapping thumbnail
Tap picture to hide or
view icons
Zoom in or out
D Movies
Movies can not be viewed using the Wireless Mobile Utility, but
movies can be played back by tapping the movie or playback icon
in the thumbnail list to display a list of movie apps and choosing
an app from the list.
in shooting display)
B
38
Page 39
A Folders
Downloaded pictures are stored in folders with names consisting
of “C” (for new photos downloaded during shooting) or “D” (for existing pictures downloaded during playback) followed by the date,
an underscore, and a 3-digit folder number. A new folder is created
each time you launch the Wireless Mobile Utility and either capture new photos or download existing pictures. To view pictures in
other folders, tap the folder icon at the top of the display and tap a
folder to display its contents.
On the smart device, the path to folders created for new photos
downloaded during shooting is “/sdcard/Nikon_WU/Capture”, while
the path to those created for existing pictures downloaded during
playback is “/sdcard/Nikon_WU/Card”.
B
39
Page 40
Downloading Existing Pictures
Download pictures from the camera memory card.
Tap View photos.
1
Tap Pictures on camera.
2
Tap Pictures on camera to view the pictures on the camera.
B
40
Page 41
Select pictures for download.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to display the desired picture and
tap the check mark to select or deselect.
Press the back button on the smart device to return to the thumbnail list.
Alternatively, you can select multiple
pictures by touching and holding a
thumbnail until check boxes are displayed at the top right corner of each
picture and then tapping thumbnails
to select or deselect. You can also tap
Select all in the smart device menu to
select all images or Deselect all to deselect all images.
Tap Download.
4
Tap Download to download the selected pictures.
B
41
Page 42
A Folders
To select all images in a folder, tap the folder icon at the top of the
display and then touch and hold the folder in the folder list.
D Dropped Connections
If the wireless connection is lost while a picture is being downloaded, the picture will not be saved to the smart device (connection
loss may occur if, for example, the camera turns off during download). Any pictures downloaded before the connection was interrupted are unaffected.
B
42
Page 43
Sharing Pictures
Before sharing pictures, connect to a network with Internet access.
zz
Sharing Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Share.
2
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
B
43
Page 44
zz
Sharing Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to share until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Share.
3
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
B
44
Page 45
A Sharing Folders
To share all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be shared by
tapping Share as described in Step 3.
B
45
Page 46
Deleting Pictures
Downloaded pictures can be deleted from the smart device one
at a time or in groups. The Wireless Mobile Utility can not be
used to delete pictures from the camera memory card.
zz
Deleting Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Delete.
2
Tap Delete.
A conrmation dialog will be displayed;
tap Yes.
B
46
Page 47
zz
Deleting Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to delete until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Delete.
3
A conrmation dialog will be displayed;
tap Yes.
B
47
Page 48
A Deleting Folders
To delete all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be deleted by
tapping Delete as described in Step 3.
B
48
Page 49
Wireless Mobile Utility Options
The smart device menu for the Wireless Mobile Utility home display can be used to access the options listed below.
Settings
Option Description
Synchronize clock
Battery options
Image size
Thumbnails
App auto launch
Choose whether to synchronize the camera clock with
the smart device.
Remote photography will end automatically when the
camera or smart device battery reaches the selected
level.
Choose whether pictures are resized for download to
the smart device. Select Original to download images
at their original size.
Choose the size of the thumbnails in the playback display.
If ON is selected, the Wireless Mobile Utility will launch
automatically when the smart device detects a signal
from the wireless mobile adapter.
B
49
Page 50
Option Description
Wireless Mobile
Adapter settings
SSID
Authentication/
encryption
Password
Channel Choose the wireless channel used by the network.
Auto power-o
delay
Advanced
settings
Current settings View current wireless mobile adapter settings.
Format settings Tap Yes to restore default settings.
Language
Adjust network settings for the wireless mobile adapter.
Choose an SSID for the wireless mobile adapter. The
smart device displays the SSID when you connect to
the network manually.
Choose the authentication method used for connection
to the network.
Enter a password. The password type is selected using
Advanced settings > Password entr y: choose ASCII for an
8- to 63-character alphanumeric password, HEX for a 64digit hexadecimal password.
Choose the delay before the wireless mobile adapter
enters sleep when there is no wireless connection.
• WPS PIN: Set the wireless mobile adapter WPS PIN.
• WPS mode: Select the adapter WPS mode.
• Password entry: Choose the password type.
• Sub-net mask: Enter a subnet mask.
• DHCP server IP address: Enter the wireless mobile adapt-
er IP address.
• DHCP client IP address: Enter the smart device IP address.
Choose the language in which the user interface for the
Wireless Mobile Utility is displayed.
B
50
Page 51
Info
Option Description
Camera The name of the camera currently connected.
Wireless Mobile
Adapter
Link speed View the transmission rate.
Serial number View the product serial number.
Firmware version View the current firmware version.
App
Exit
Exit the Wireless Mobile Utility.
View information about the wireless mobile adapter.
Select About to view Wireless Mobile Utility version information, Check for updates to connect to
the Google Play service and check for updates, or
License Terms and Conditions to view the terms of use
for this application.
B
51
Page 52
Nikon 1: V2, J3, S1
C
This section describes the options available when the Wireless
Mobile Utility and an optional wireless mobile adapter are used
to connect to Nikon 1 V2, J3, and S1 cameras.
Features
Use the Wireless Mobile Utility to:
Take pictures remotely (0 56): Tap the shutter icon in the Wireless Mobile Utility to
take pictures and download them to
the smart device.
View pictures (0 59): View the pictures stored on the smart device or
the camera memory card.
Download pictures (0 63): Download existing pictures from the camera memory card.
Share pictures (0 66): Share pictures via e-mail or upload pictures to
photo-sharing sites.
For information on inserting the adapter, see page 54.
C
52
Page 53
Notices
• No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form without Nikon’s prior written permission.
• Nikon reserves the right to change the specications of the hardware and software described in this manual at any time and
without prior notice. Nikon will not be held liable for damages
that may result from any mistakes that this manual may contain.
System Requirements
Before installing the Wireless Mobile Utility, conrm that your
smart device meets the following system requirements:
OS
Wireless LAN 11b/g/n
Screen resolution 800 × 480 pixels (WVGA) or higher
D Using This Application for the First Time
You must accept the terms and conditions of the End User License
Agreement (EULA) before connecting.
• Smartphone: Android 2.3 series, Android 4.x series
• Tablet: Android 3.x series, Android 4.x series
C
53
Page 54
Installing the App
Locate the app on Google Play.
1
Connect to Google Play on the smart device and search for
“Wireless Mobile Utility”.
Install the app.
2
Install the Wireless Mobile Utility.
Establishing a Wireless Connection
Connect the wireless mobile adapter.
1
Attach the wireless mobile adapter to the camera and turn
the camera on. See the manual supplied with the wireless
mobile adapter for details.
Ready the smart device.
2
Select Wi-Fi settings > WPS button connection. The smart
device will wait for a signal from the camera.
Press the WPS button.
3
Press the WPS button on the wireless mobile adapter for
about 5 s until the LED on the wireless mobile adapter ashes red and green.
Launch the Wireless Mobile Utility.
4
When a connection is established, the LED on the wireless
mobile adapter will glow green and the main dialog for the
Wireless Mobile Utility will be displayed on the smart device. For information on taking pictures, see page
formation on viewing pictures, see page
59.
56. For in-
C
54
Page 55
A WPS
WPS (Wi-Fi Protected Setup) is a standard designed to make it easy
to establish a secure wireless network. For information on the steps
involved and the length of time the smart device will wait for a connection, see the documentation supplied with the smart device.
A Manual Wireless Connections
Display Wi-Fi settings for the smart device.
1
Select the mobile adapter SSID (the default SSID begins with
2
“Nikon_WU_”). The LED will light green when a connection is
established.
D The Wireless Mobile Adapter
While the adapter is inserted, the camera exposure meters will not
turn off; monitor the camera battery level to ensure that the camera does not power off unexpectedly. In addition, some camera
menu items may be grayed out and unavailable and the camera
can not be used for playback or live view. Movie recording can
not be used.
C
55
Page 56
Taking Photos
Follow the steps below to take photos from the smart device.
Tap Take photos.
1
The camera viewnder will go dark and the smart device
will display the view through the camera lens.
Tap the shutter icon.
2
The shutter will be released after you
remove your nger from the icon and
the camera focuses (note that no photo
will be taken if the camera is unable to
focus); the resulting photo is rst saved
to the camera memory card and then
downloaded to the smart device. There
is no need to point the smart device at
the wireless mobile adapter.
C
56
Page 57
D Remote Photography
Remote photography ends automatically when the battery in the
camera or smart device runs low. Note that using remote photography for an extended period may cause the camera’s internal
temperature to rise; if necessary, remote photography will end automatically to minimize damage to camera circuits.
The smart device can not be used to adjust camera settings; use
camera controls to adjust settings before starting Step 1. Regardless of the release mode selected with the camera, only one picture
will be taken each time you tap the shutter icon. Note that the
display may not update smoothly depending on the device and
network conditions.
Regardless of the settings selected with the camera, pictures will be
taken in mode P (programmed auto) using single-servo autofocus
(AF-S) and auto-area AF. Face-priority AF is disabled and the focus
point is not displayed.
C
57
Page 58
A The Remote Photography Display
Settings: The following photographyrelated options can be accessed from
the smart device menu.
• Remote shooting auto download:
Choose whether to download pictures
to the smart device after shooting.
• Self-timer: If ON is selected, the camera shutter will be released 2 s after
you tap the shutter icon. The timer
turns off automatically after the shutter is released.
Self-timer icon: Displayed when the selftimer is on.
Camera settings: Shutter speed, aperture,
etc. Not displayed when device is in
landscape orientation.
Thumbnail area: Downloaded pictures.
C
58
Page 59
Viewing Photos
Tap View photos to view the pictures stored on the smart device. You can also view the pictures on the camera memory card
and download selected images to the smart device.
Viewing Pictures
View the pictures in camera memory or on the smart device.
Tap View photos.
1
C
59
Page 60
Choose a device.
2
Tap Pictures on camera to view the pictures on the camera
memory card, Pictures on smart device to view the pictures
stored on the smart device. The pictures will be displayed
as small “thumbnail” images (in some cases, a folder list may
be displayed; tap a folder to view the pictures it contains).
View pictures.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to view additional pictures.
C
60
Page 61
A The Full-Frame Display
The full-frame display is shown below.
Return to shooting
mode (available only
if display was accessed
by tapping thumbnail
Tap picture to hide or
view icons
Zoom in or out
D Movies
Movies can not be viewed using the Wireless Mobile Utility, but
movies can be played back by tapping the movie or playback icon
in the thumbnail list to display a list of movie apps and choosing
an app from the list.
in shooting display)
C
61
Page 62
A Folders
Downloaded pictures are stored in folders with names consisting
of “C” (for new photos downloaded during shooting) or “D” (for existing pictures downloaded during playback) followed by the date,
an underscore, and a 3-digit folder number. A new folder is created
each time you launch the Wireless Mobile Utility and either capture new photos or download existing pictures. To view pictures in
other folders, tap the folder icon at the top of the display and tap a
folder to display its contents.
On the smart device, the path to folders created for new photos
downloaded during shooting is “/sdcard/Nikon_WU/Capture”, while
the path to those created for existing pictures downloaded during
playback is “/sdcard/Nikon_WU/Card”.
C
62
Page 63
Downloading Existing Pictures
Download pictures from the camera memory card.
Tap View photos.
1
Tap Pictures on camera.
2
Tap Pictures on camera to view the pictures on the camera.
C
63
Page 64
Select pictures for download.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to display the desired picture and
tap the check mark to select or deselect.
Press the back button on the smart device to return to the thumbnail list.
Alternatively, you can select multiple
pictures by touching and holding a
thumbnail until check boxes are displayed at the top right corner of each
picture and then tapping thumbnails
to select or deselect. You can also tap
Select all in the smart device menu to
select all images or Deselect all to deselect all images.
Tap Download.
4
Tap Download to download the selected pictures.
C
64
Page 65
A Folders
To select all images in a folder, tap the folder icon at the top of the
display and then touch and hold the folder in the folder list.
D Dropped Connections
If the wireless connection is lost while a picture is being downloaded, the picture will not be saved to the smart device (connection
loss may occur if, for example, the camera turns off during download). Any pictures downloaded before the connection was interrupted are unaffected.
C
65
Page 66
Sharing Pictures
Before sharing pictures, connect to a network with Internet access.
zz
Sharing Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Share.
2
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
C
66
Page 67
zz
Sharing Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to share until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Share.
3
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
C
67
Page 68
A Sharing Folders
To share all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be shared by
tapping Share as described in Step 3.
C
68
Page 69
Deleting Pictures
Downloaded pictures can be deleted from the smart device one
at a time or in groups. The Wireless Mobile Utility can not be
used to delete pictures from the camera memory card.
zz
Deleting Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Delete.
2
Tap Delete.
A conrmation dialog will be displayed;
tap Yes.
C
69
Page 70
zz
Deleting Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to delete until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Delete.
3
A conrmation dialog will be displayed;
tap Yes.
C
70
Page 71
A Deleting Folders
To delete all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be deleted by
tapping Delete as described in Step 3.
C
71
Page 72
Wireless Mobile Utility Options
The smart device menu for the Wireless Mobile Utility home display can be used to access the options listed below.
Settings
Option Description
Synchronize clock
Battery options
Image size
Thumbnails
App auto launch
Choose whether to synchronize the camera clock with
the smart device.
Remote photography will end automatically when the
camera or smart device battery reaches the selected
level.
Choose whether pictures are resized for download to
the smart device. Select Original to download images
at their original size.
Choose the size of the thumbnails in the playback display.
If ON is selected, the Wireless Mobile Utility will launch
automatically when the smart device detects a signal
from the wireless mobile adapter.
C
72
Page 73
Option Description
Wireless Mobile
Adapter settings
SSID
Authentication/
encryption
Password
Channel Choose the wireless channel used by the network.
Auto power-o
delay
Advanced
settings
Current settings View current wireless mobile adapter settings.
Format settings Tap Yes to restore default settings.
Language
Adjust network settings for the wireless mobile adapter.
Choose an SSID for the wireless mobile adapter. The
smart device displays the SSID when you connect to
the network manually.
Choose the authentication method used for connection
to the network.
Enter a password. The password type is selected using
Advanced settings > Password entr y: choose ASCII for an
8- to 63-character alphanumeric password, HEX for a 64digit hexadecimal password.
Choose the delay before the wireless mobile adapter
enters sleep when there is no wireless connection.
• WPS PIN: Set the wireless mobile adapter WPS PIN.
• WPS mode: Select the adapter WPS mode.
• Password entry: Choose the password type.
• Sub-net mask: Enter a subnet mask.
• DHCP server IP address: Enter the wireless mobile adapt-
er IP address.
• DHCP client IP address: Enter the smart device IP address.
Choose the language in which the user interface for the
Wireless Mobile Utility is displayed.
C
73
Page 74
Info
Option Description
Camera The name of the camera currently connected.
Wireless Mobile
Adapter
Link speed View the transmission rate.
Serial number View the product serial number.
Firmware version View the current firmware version.
App
Exit
Exit the Wireless Mobile Utility.
View information about the wireless mobile adapter.
Select About to view Wireless Mobile Utility version information, Check for updates to connect to
the Google Play service and check for updates, or
License Terms and Conditions to view the terms of use
for this application.
C
74
Page 75
COOLPIX: P520, P330, S9500, S6500, S5200,
D
AW110
This section describes the options available when the Wireless
Mobile Utility is used to connect to COOLPIX P520, P330, S9500,
S6500, S5200, and AW110 cameras.
Features
Use the Wireless Mobile Utility to:
Take pictures remotely (0 79): Tap the shutter icon in the Wireless Mobile Utility to
take pictures and download them to
the smart device.
View pictures (0 82): View the pictures stored on the smart device or
the camera memory card.
Download pictures (0 86): Download existing pictures from the camera memory card.
Share pictures (0 89): Share pictures via e-mail or upload pictures to
photo-sharing sites.
Note that an optional wireless mobile adapter is required when
the app is used with cameras not equipped with built-in wireless; for information on inserting the adapter, see page
77.
D
75
Page 76
Notices
• No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form without Nikon’s prior written permission.
• Nikon reserves the right to change the specications of the hardware and software described in this manual at any time and
without prior notice. Nikon will not be held liable for damages
that may result from any mistakes that this manual may contain.
System Requirements
Before installing the Wireless Mobile Utility, conrm that your
smart device meets the following system requirements:
OS
Wireless LAN 11b/g/n
Screen resolution 800 × 480 pixels (WVGA) or higher
D Using This Application for the First Time
You must accept the terms and conditions of the End User License
Agreement (EULA) before connecting.
• Smartphone: Android 2.3 series, Android 4.x series
• Tablet: Android 3.x series, Android 4.x series
D
76
Page 77
Installing the App
Locate the app on Google Play.
1
Connect to Google Play on the smart device and search for
“Wireless Mobile Utility”.
Install the app.
2
Install the Wireless Mobile Utility.
Establishing a Wireless Connection
The following applies only to cameras without built-in Wi-Fi. For
information on cameras with built-in Wi-Fi, see the manual provided with the camera.
Connect the wireless mobile adapter.
1
Attach the wireless mobile adapter to the camera and turn
the camera on. See the manual supplied with the wireless
mobile adapter for details.
Ready the smart device.
2
Select Wi-Fi settings > WPS button connection. The smart
device will wait for a signal from the camera.
Press the WPS button.
3
Press the WPS button on the wireless mobile adapter for
about 5 s until the LED on the wireless mobile adapter ashes red and green.
Launch the Wireless Mobile Utility.
4
When a connection is established, the LED on the wireless
mobile adapter will glow green and the main dialog for the
Wireless Mobile Utility will be displayed on the smart device. For information on taking pictures, see page
formation on viewing pictures, see page 82.
79. For in-
D
77
Page 78
A WPS
WPS (Wi-Fi Protected Setup) is a standard designed to make it easy
to establish a secure wireless network. For information on the steps
involved and the length of time the smart device will wait for a connection, see the documentation supplied with the smart device.
A Manual Wireless Connections
Display Wi-Fi settings for the smart device.
1
Select the camera or mobile adapter SSID (the default SSID be-
2
gins with “Nikon”). If you are using a wireless mobile adapter, the
LED will light green when a connection is established.
D The Wireless Mobile Adapter (for Cameras Without Built-in Wi-Fi)
While the adapter is inserted, the camera exposure meters will not
turn off; monitor the camera battery level to ensure that the camera does not power off unexpectedly. In addition, some camera
menu items may be grayed out and unavailable and the camera
can not be used for playback or live view. Movie recording can
not be used.
D
78
Page 79
Taking Photos
Follow the steps below to take photos from the smart device.
Tap Take photos.
1
The camera viewnder will go dark and the smart device
will display the view through the camera lens.
Tap the shutter icon.
2
The shutter will be released after you remove your nger from the icon and the
camera focuses; the resulting photo is
rst saved to the camera memory card
and then downloaded to the smart device. There is no need to point the smart
device at the wireless mobile adapter.
D
79
Page 80
D Remote Photography
Remote photography ends automatically when the battery in the
camera or smart device runs low. Note that using remote photography for an extended period may cause the camera’s internal
temperature to rise; if necessary, remote photography will end automatically to minimize damage to camera circuits.
The smart device can not be used to adjust camera settings; use
camera controls to adjust settings before starting Step 1. Regardless of the release mode selected with the camera, only one picture
will be taken each time you tap the shutter icon. Note that the
display may not update smoothly depending on the device and
network conditions.
Regardless of the settings selected with the camera, pictures will be
taken in C (auto) mode using target finding autofocus. The focus
point is not displayed.
D
80
Page 81
A The Remote Photography Display
Settings: The following photographyrelated options can be accessed from
the smart device menu.
• Remote shooting auto download:
Choose whether to download pictures
to the smart device after shooting.
• Self-timer: If ON is selected, the camera shutter will be released 2 s after
you tap the shutter icon. The timer
turns off automatically after the shutter is released.
Self-timer icon: Displayed when the selftimer is on.
Camera settings: Shutter speed, aperture,
etc. Not displayed when device is in
landscape orientation.
Optical zoom: Tap T to zoom in, W to zoom
out.
Thumbnail area: Downloaded pictures.
D
81
Page 82
Viewing Photos
Tap View photos to view the pictures stored on the smart device. You can also view the pictures on the camera memory card
and download selected images to the smart device.
Viewing Pictures
View the pictures in camera memory or on the smart device.
Tap View photos.
1
D
82
Page 83
Choose a device.
2
Tap Pictures on camera to view the pictures on the camera
memory card, Pictures on smart device to view the pictures
stored on the smart device. The pictures will be displayed
as small “thumbnail” images (in some cases, a folder list may
be displayed; tap a folder to view the pictures it contains).
View pictures.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to view additional pictures.
D
83
Page 84
A The Full-Frame Display
The full-frame display is shown below.
Return to shooting
mode (available only
if display was accessed
by tapping thumbnail
Tap picture to hide or
view icons
Zoom in or out
D Movies
Movies can not be viewed using the Wireless Mobile Utility, but
movies can be played back by tapping the movie or playback icon
in the thumbnail list to display a list of movie apps and choosing
an app from the list.
in shooting display)
D
84
Page 85
A Folders
Downloaded pictures are stored in folders with names consisting
of “C” (for new photos downloaded during shooting) or “D” (for existing pictures downloaded during playback) followed by the date,
an underscore, and a 3-digit folder number. A new folder is created
each time you launch the Wireless Mobile Utility and either capture new photos or download existing pictures. To view pictures in
other folders, tap the folder icon at the top of the display and tap a
folder to display its contents.
On the smart device, the path to folders created for new photos
downloaded during shooting is “/sdcard/Nikon_WU/Capture”, while
the path to those created for existing pictures downloaded during
playback is “/sdcard/Nikon_WU/Card”.
D
85
Page 86
Downloading Existing Pictures
Download pictures from the camera memory card. Note that 3D
images are downloaded as 2D JPEG images.
Tap View photos.
1
Tap Pictures on camera.
2
Tap Pictures on camera to view the pictures on the camera.
D
86
Page 87
Select pictures for download.
3
Tap a thumbnail to display the picture
full frame. You can then swipe left or
right to display the desired picture and
tap the check mark to select or deselect.
Press the back button on the smart device to return to the thumbnail list.
Alternatively, you can select multiple
pictures by touching and holding a
thumbnail until check boxes are displayed at the top right corner of each
picture and then tapping thumbnails
to select or deselect. You can also tap
Select all in the smart device menu to
select all images or Deselect all to deselect all images.
Tap Download.
4
Tap Download to download the selected pictures.
D
87
Page 88
A Folders
To select all images in a folder, tap the folder icon at the top of the
display and then touch and hold the folder in the folder list.
D Dropped Connections
If the wireless connection is lost while a picture is being downloaded, the picture will not be saved to the smart device (connection
loss may occur if, for example, the camera turns off during download). Any pictures downloaded before the connection was interrupted are unaffected.
D
88
Page 89
Sharing Pictures
Before sharing pictures, connect to a network with Internet access.
zz
Sharing Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Share.
2
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
D
89
Page 90
zz
Sharing Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to share until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Share.
3
Tap Share and choose from a list of
picture-sharing apps and functions (the
specic contents of the list vary from device to device).
D
90
Page 91
A Sharing Folders
To share all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be shared by
tapping Share as described in Step 3.
D
91
Page 92
Deleting Pictures
Downloaded pictures can be deleted from the smart device one
at a time or in groups. The Wireless Mobile Utility can not be
used to delete pictures from the camera memory card.
zz
Deleting Pictures One at a Time
Display the smart device menu.
1
Display a picture full-frame and tap the
menu button on the smart device to
view menu options.
Tap Delete.
2
Tap Delete.
A conrmation dialog will be displayed;
tap Yes.
D
92
Page 93
zz
Deleting Multiple Pictures
Display check boxes.
1
In the thumbnail list, touch and hold any
of the pictures you want to delete until a
check mark is displayed in the top right
corner and check boxes appear on the
remaining images.
Select pictures.
2
Tap thumbnails to select or deselect.
You can also tap Select all in the smart
device menu to select all images or De-
select all to deselect all images.
Tap Delete.
3
A conrmation dialog will be displayed;
tap Yes.
D
93
Page 94
A Deleting Folders
To delete all pictures in a folder, tap the folder
icon at the top of the display to view folders,
then touch and hold a folder to select all the
pictures it contains. Selected pictures are indicated by check marks and can be deleted by
tapping Delete as described in Step 3.
D
94
Page 95
Wireless Mobile Utility Options
The smart device menu for the Wireless Mobile Utility home display can be used to access the options listed below.
Settings
Option Description
Synchronize clock
Battery options
Image size
Thumbnails
App auto launch
Choose whether to synchronize the camera clock with
the smart device.
Remote photography will end automatically when the
camera or smart device battery reaches the selected
level.
Choose whether pictures are resized for download to
the smart device. Select Original to download images
at their original size.
Choose the size of the thumbnails in the playback display.
If ON is selected, the Wireless Mobile Utility will launch
automatically when the smart device detects a signal
from the wireless mobile adapter.
D
95
Page 96
Option Description
Wireless Mobile
Adapter settings
SSID
Authentication/
encryption
Password
Channel Choose the wireless channel used by the network.
Auto power-o
delay
Advanced
settings
Current settings View current wireless mobile adapter settings.
Format settings Tap Yes to restore default settings.
Language
Adjust network settings for the wireless mobile adapter.
Not available with cameras featuring built-in Wi-Fi.
Choose an SSID for the wireless mobile adapter. The
smart device displays the SSID when you connect to
the network manually.
Choose the authentication method used for connection
to the network.
Enter a password. The password type is selected using
Advanced settings > Password entr y: choose ASCII for an
8- to 63-character alphanumeric password, HEX for a 64digit hexadecimal password.
Choose the delay before the wireless mobile adapter
enters sleep when there is no wireless connection.
• WPS PIN: Set the wireless mobile adapter WPS PIN.
• WPS mode: Select the adapter WPS mode.
• Password entry: Choose the password type.
• Sub-net mask: Enter a subnet mask.
• DHCP server IP address: Enter the wireless mobile adapt-
er IP address.
• DHCP client IP address: Enter the smart device IP address.
Choose the language in which the user interface for the
Wireless Mobile Utility is displayed.
D
96
Page 97
Info
Option Description
Camera The name of the camera currently connected.
Wireless Mobile
Adapter
Link speed View the transmission rate.
Serial number View the product serial number.
Firmware version View the current firmware version.
App
Exit
Exit the Wireless Mobile Utility.
View information about the wireless connection. The
serial number and firmware version are displayed
only if the camera is connected via the wireless mobile adapter.
Select About to view Wireless Mobile Utility version information, Check for updates to connect to
the Google Play service and check for updates, or
License Terms and Conditions to view the terms of use
for this application.
SB3C08(11)
6MWA1811-08
D
97
Loading...