NEXCOM PEAK 887VL2 User Manual

NEXCOM International Co., Ltd.

Industrial Computing Solutions

PICMG Single Board Computer (PICMG 1.3) PEAK 887VL2

User Manual

NEXCOM International Co., Ltd.

Published October 2013

www.nexcom.com

Content

Contents

Preface

Copyright ............................................................................................. iv

Disclaimer .............................................................................................. iv

Acknowledgements ............................................................................... iv

Regulatory Compliance Statements ........................................................ iv

Declaration of Conformity ...................................................................... iv

RoHS Compliance ................................................................................... v

Warranty and RMA ................................................................................ vi

Safety Information ................................................................................viii

Installation Recommendations ...............................................................viii

Safety Precautions .................................................................................. ix

Technical Support and Assistance ............................................................ x

Conventions Used in this Manual ............................................................ x

Global Service Contact Information ........................................................ xi

Package Contents ................................................................................. xiii

Ordering Information ............................................................................xiv

Chapter 1: Product Introduction

Overview ................................................................................................1

Key Features ...........................................................................................1

Hardware Specifications ..........................................................................2

Knowing Your PEAK 887VL2 ................................................................... 4

Chapter 2: Jumpers and Connectors

Before You Begin ....................................................................................5

Precautions ............................................................................................5

Jumper Settings ......................................................................................6

Locations of the Jumpers and Connectors ............................................... 7

Jumpers .................................................................................................. 8

CMOS Clear Select ..............................................................................8

AT/ATX Select ......................................................................................8

Connector Pin Definitions .......................................................................9

External Connectors ............................................................................9

VGA Port .........................................................................................9

LAN1 Port ........................................................................................9

LAN2 Port ......................................................................................10

USB 3.0 Ports ................................................................................. 10

Internal Connectors ........................................................................... 11

USB 3.0 Port ..................................................................................11

USB 2.0 Ports ................................................................................. 11

+12V Power Connector .................................................................. 12

CPU FAN Connector .......................................................................12

System FAN Connector ...................................................................13

Keyboard and Mouse Connector ....................................................13

COM1 Box Header Connector ........................................................ 14

COM2 Box Header Connector ........................................................ 14

COM3 Box Header Connector ........................................................ 15

COM4 Box Header Connector ........................................................ 15

Printer Port .....................................................................................16

DVI/ HDMI Port Connector .............................................................16

SATA Connector .............................................................................17

ii

PEAK 887VL2 User Manual

Content

SATA Connector .............................................................................17

SATA Connector .............................................................................18

COM2 RI# Voltage Select ...............................................................19

SATA DOM Power Connector .........................................................19

LAN LED Pin Header ....................................................................... 20

Power On/Off/Reset & PWR/HDD LED Pin Header ...........................20

DIP Switch ......................................................................................21

Debug Port ....................................................................................21

Chapter 3: BIOS Setup

About BIOS Setup ................................................................................. 22

When to Configure the BIOS .................................................................22

Default Configuration ........................................................................... 23

Entering Setup ...................................................................................... 23

Legends ................................................................................................ 23

BIOS Setup Utility .................................................................................. 25

Main .................................................................................................25

Advanced .......................................................................................... 26

Chipset ..............................................................................................37

Boot .................................................................................................. 38

Security .............................................................................................39

Save & Exit ........................................................................................39

iii

PEAK 887VL2 User Manual

Preface

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co., Ltd. However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom.com. NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

PEAK 887VL2 is a trademark of NEXCOM International Co., Ltd. All other product names mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class B devices and describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense.

CE

The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.

iv

PEAK 887VL2 User Manual

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status Update

This publication, including all photographs, illustrations and software, is protected under international copyright

laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force to implement the introduction of green products. The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2006 will be RoHS compliant. They will use the usual NEXCOM naming convention.

v

PEAK 887VL2 User Manual

Preface

Warranty and RMA

NEXCOM Warranty Period

NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard. NEXCOM warrants that products will be free from defect in material and workmanship for 2 years, beginning on the date of invoice by NEXCOM. HCP series products (Blade Server) which are manufactured by NEXCOM are covered by a three year warranty period.

NEXCOM Return Merchandise Authorization (RMA)

▪ Customers shall enclose the “NEXCOM RMA Service Form” with the

returned packages.

▪ Customers must collect all the information about the problems

encountered and note anything abnormal or, print out any on-screen messages, and describe the problems on the “NEXCOM RMA Service Form” for the RMA number apply process.

▪ Customers can send back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the card, such as CPU and RAM. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise, NEXCOM is not responsible for the devices/parts.

▪ Customers are responsible for the safe packaging of defective products,

making sure it is durable enough to be resistant against further damage and deterioration during transportation. In case of damages occurred during transportation, the repair is treated as “Out of Warranty.”

▪ Any products returned by NEXCOM to other locations besides the

customers’ site will bear an extra charge and will be billed to the customer.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

System Level

▪ Component fee: NEXCOM will only charge for main components such as

SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistor, capacitor.

▪ Items will be replaced with NEXCOM products if the original one cannot

be repaired. Ex: motherboard, power supply, etc.

▪ Replace with 3rd party products if needed.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Board Level

▪ Component fee: NEXCOM will only charge for main components, such

as SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistors, capacitors.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

vi

PEAK 887VL2 User Manual

Preface

Warnings

Read and adhere to all warnings, cautions, and notices in this guide and the documentation supplied with the chassis, power supply, and accessory modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules, contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements.

Cautions

Electrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

vii

PEAK 887VL2 User Manual

Preface

Safety Information

Before installing and using the device, note the following precautions:

▪ Read all instructions carefully.

▪ Do not place the unit on an unstable surface, cart, or stand.

▪ Follow all warnings and cautions in this manual.

▪ When replacing parts, ensure that your service technician uses parts

specified by the manufacturer.

▪ Avoid using the system near water, in direct sunlight, or near a heating

device.

▪ The load of the system unit does not solely rely for support from the

rackmounts located on the sides. Firm support from the bottom is highly necessary in order to provide balance stability.

▪ The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated.

Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:

▪ A Philips screwdriver

▪ A flat-tipped screwdriver

▪ A grounding strap

▪ An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

viii

PEAK 887VL2 User Manual

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a

damp cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a stable surface during installation. Dropping it or

letting it fall may cause damage.

7. The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting

the equipment to the power outlet.

9. Place the power cord in a way so that people will not step on it. Do not

place anything on top of the power cord. Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product’s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work

according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15. Do not place heavy objects on the equipment.

16. The unit uses a three-wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does not support this kind of plug, contact your electrician to replace your obsolete outlet.

17. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

ix

PEAK 887VL2 User Manual

Preface

CAUTION!

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or sales representative, please have the following information ready before calling: – Product name and serial number – Detailed information of the peripheral devices – Detailed information of the installed software (operating system,

version, application software, etc.) – A complete description of the problem – The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth.

3. CompactFlash: Turn off the unit’s power before inserting or removing a CompactFlash storage card.

Conventions Used in this Manual

Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task.

CAUTION!CAUTION!

Caution: Information to avoid damaging components or losing data.

Note: Provides additional information to complete a task easily.

x

PEAK 887VL2 User Manual

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

15F, No. 920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7786 Fax: +886-2-8226-7782 www.nexcom.com.tw

America

USA NEXCOM USA

2883 Bayview Drive, Fremont CA 94538, USA Tel: +1-510-656-2248 Fax: +1-510-656-2158 Email: sales@nexcom.com www.nexcom.com

Asia

Taiwan Taichung Office

16F, No.250, Sec. 2, Chongde Rd., Beitun Dist., Taichung City 406, R.O.C. Tel: +886-4-2249-1179 Fax: +886-4-2249-1172 www.nexcom.com.tw Japan

NEXCOM Japan

9F, Tamachi Hara Bldg.,4-11-5, Shiba Minato-ku, Tokyo, 108-0014, Japan Tel: +81-3-5419-7830 Fax: +81-3-5419-7832 Email: sales@nexcom-jp.com www.nexcom-jp.com

China NEXCOM China

2F, Block 4, Venus Plaza, Building 21, ZhongGuanCun Software Park, No.8, Dongbeiwang West Road, Haidian District, Beijing, 100193, China Tel: +86-10-8282-5880 Fax: +86-10-8282-5955 Email: sales@nexcom.cn www.nexcom.cn

Shanghai Office

Room 1505, Greenland He Chuang Bldg., No. 450 Caoyang Rd., Shanghai, 200062, China Tel: +86-21-6150-8008 Fax: +86-21-3251-6358 Email: sales@nexcom.cn www.nexcom.cn

Nanjing Office

Hall C, Block 17, Tian Xing Cui Lang Bldg., No. 49 Yunnan North Rd., Nanjing, 210018, China Tel: +86-25-8315-3486 Fax: +86-25-8315-3489 Email: sales@nexcom.cn www.nexcom.cn

Shenzhen Office

Western Room 708, Block 210, Tairan Industry & Trading Place, Futian Area, Shenzhen, 518040, China Tel: +86-755-833 7203 Fax: +86-755-833 7213 Email: sales@nexcom.cn www.nexcom.cn

Wuhan Office

1-C1804/1805,Mingze Liwan, No.519 South Luoshi Rd,Hongshan District, Wuhan,430070,China Tel: +86-27-8722-7400 Fax: +86-27-8722-7400 Email: sales@nexcom.cn www.nexcom.cn

xi

PEAK 887VL2 User Manual

Preface

Chengdu Office

Chengdu Office 9F,Shuxiangxie,Xuefu Garden, No.12 Section 1,South Yihuan Rd,Chengdu, 610061,China Tel: +86-28-8523-0186 Fax: +86-28-8523-0186 Email: sales@nexcom.cn www.nexcom.cn

Europe

France NEXCOM France

La Grande Arche-Paroi Nord 92044 Paris La Défense France Tel: +33 (0) 1 40 90 33 35 Fax: +33 (0) 1 40 90 31 01 Email: sales.fr@nexcom.eu www.nexcom.eu

Germany

NEXCOM GmbH Leopoldstraße Business Centre, Leopoldstraße 244, 80807 Munich, Germany Tel: +49-89-208039-278 Fax: +49-89-208039-279 Email: sales.de@nexcom.eu www.nexcom.eu

Italy

NEXCOM ITALIA S.r.l Via Gaudenzio Ferrari 29, 21047 Saronno (VA), Italia Tel: +39 02 9628 0333 Fax: +39 02 9286 9215 Email: nexcomitalia@nexcom.eu www.nexcomitalia.it

United Kingdom NEXCOM EUROPE

10 Vincent Avenue, Crownhill Business Centre, Milton Keynes, Buckinghamshire MK8 0AB, United Kingdom Tel: +44-1908-267121 Fax: +44-1908-262042 Email: sales.uk@nexcom.eu www.nexcom.eu

xii

PEAK 887VL2 User Manual

Preface

Package Contents

Before continuing, verify that the PEAK 887VL2 package that you received is complete. Your package should have all the items listed in the following table.

Item Part Number Name Description Qty

1 10P0887VL00X0 ASSY PEAK 887VL2 PICMG 1.3 computing board 1 2 60177B0268X00 PEAK 887VL2 Quick Reference Guide VER:B KRAMER 1 3 60233ATA73X00 SATA cable ACMELUX: 19922413 Standard L:300mm 1 4 60233PRT15X00 Cable CONNTEK: A02-C016-V01 Print 25 to 2.0mm 26-pin PIT:1.0mm L:260mm w/bracket 1 5 603PS20001X00 PS2 Y CABLE CONNTEK:A02-A052-V01 PS2 to JST 6P PH:2.0 L=250mm 1

6 60233SIO03X00 Cable EDI: 13420901511-RS

COM port 9-pin to housing 10-pin PIT: 2.0mm x2 L:150mm+-10mm

7 60233USB60X00 USB cable CONNTEK: A02-B001-V01 USB CONx2+bracket to JST 6-pin 2.5mm L:240+-15mm 1

8 6029900037X00

DOW Corning 340 Silcone Heat Sink Compound(3g)

9 602DCD0745X00 PEAK 887VL2 DVD Driver VER:1.0 JCL 1

Optional Accessories

1

Item Part Number Name Description

1 60233DVI32X00 DVI Cable ST:MD-6301035 DVI 24+5P/F + bracket to DF13 2x15P PH:1.25 L:250mm 2 60233HDM01X00 HDMI Cable CONNTEK:A02-A039_V24 HDMI 19P/F + bracket to DF13 2x15P PH:1.25 L:250mm 3 60233US119X00 (N) USB 3.0 Cable ST:13-450-E007 USB A/Fx2 TO 2x10P L=380mm 4 5050300481X00 LGA1156 CPU Cooler USE:FHSA9025S-1288 88 x 88 x 36.7mm AL6063 7010FAN 4300RPM L:200mm

xiii

PEAK 887VL2 User Manual

Preface

Ordering Information

The following information below provides ordering information for PEAK 887VL2.

PEAK 887VL2 (P/N: TBD)

PICMG 1.3 Full-size SBC, 4th Generation Intel® Core™ i7/i5/i3 Processors with Max 16GB, DDR3L DIMM, VGA integration, Intel® Gigabit Ethernet x2, USB 3.0 x4, SATA 3.0 x3

xiv

PEAK 887VL2 User Manual

Chapter 1: Product Introduction

Overview

Key Features

▪ Scalable platform 4th generation Intel® Core™ i7/i5/i3 processor +

Non-ECC

®

▪ Intel

Q87 PCH chipset support PICMG 1.3 specification

▪ Support dual channel DDR3L with NON-ECC DIMMs 1333/1600MHz up

to 16GB

▪ Support PCIe x16, 4x PCIe x1, 4x USB 3.0/ 4x USB 2.0, 4x SATA 3.0/

2x SATA 2.0 and GbE

▪ Display support for VGA, DVI, HDMI

▪ Dimension 338.58 x 126.39 mm

1

2

(W x L) (8 layers single side)

PEAK 887VL2 User Manual

Chapter 1: Product Introduction

Hardware Specifications

CPU Support

▪ 4th generation Intel® Core™ i7/i5/i3 processor (95W/ 65W/ 45W/ 35W)

TDPs, Socket LGA 1150

Main Memory

▪ 2x DIMM, support dual channel DDR3L (default)/ DDR3 NON-ECC DIMM

(dual voltage models by auto detection for DDR3 and DDR3L)

▪ Maximum 16 GB – 1066/1333/1600 MT/S

Platform Control Hub

▪ Intel® Q87 Express Chipset PCH

BIOS

▪ AMI System BIOS ▪ 16MBit SPI depended on AMT function ▪ Dual BIOS for four PCIe x1 and one PCIe x4 auto-detection

Display

▪ The Processor Graphics contains a refresh of the seventh generation

graphics

®

▪ Intel

HD Graphics GT1/GT2 ▪ Share system memory ▪ Analog Display Support ▪ Drive a standard progressive scan analog monitor

Audio

▪ Reverse HDA interface, 2.0mm 2x5 pin header

On-board LAN

▪ 1x Intel® I217LM GbE PHY ▪ 1x Intel

®

I211 Gigabit Ethernet Controller ▪ RJ45 with LED connecter x 2 ▪ Support Boot From LAN (PXE) ▪ RJ45 LED ▪ Support Wake on LAN ▪ Extra (External) LED: 2 x 4 pin header

I/O Interface

▪ ITE8783 ▪ PS2 KB/MS reserve 1x6 (2.0m) JST connector ▪ 26-pin Box Header x 1 (2.0mm) ▪ SIO Box Header x 4 (2.0mm), COM1, 3, 4 support RS232, COM2

RS232/422/485, RI pin can be select RI/5V/12V with jumper (2x3 pin

2.0mm pin-header)

▪ 4 Ports USB 2.0 and 4 ports USB 3.0:

2 ports through 2.5mm JST Connectors, located near Rear Side of PCB

(near CPU, USB 3.0) 4 ports through backplane (USB 2.0) 2 ports through I/O bracket (USB 3.0)

▪ 4-pin FAN connector x 2 (for CPU, System) ▪ On board pin header for IrDA Tx Rx 1x5/2.54mm pin-header ▪ HDD LED/ Power LED/ Power ON SW/ Reset SW ▪ On Board buzzer ▪ USB x1/ USB x1/ LAN1 RJ45 x1/ LAN2 RJ45 x1/ VGA DB15 from top to

down

2

PEAK 887VL2 User Manual

Chapter 1: Product Introduction

Power Requirements

▪ Power source from Backplane through Golden Finger and AUX +12V ▪ Support ATX/AT function by jumper setting ▪ BIOS default is (ATX MODE)

Dimensions

▪ 338.58mm x 126.39mm, 8 layers (single side)

Environment

▪ Board Level Operating temperatures: -15°C to 60°C ▪ Storage temperatures: -20°C to 85°C

▪ Relative humidity: 10% to 90% (operating, non-condensing) 5% to 95% (non-operating, non-condensing)

Certifications

▪ CE approval

▪ FCC Class A

▪ CB/CCC certification

3

PEAK 887VL2 User Manual

Chapter 1: Product Introduction

Knowing Your PEAK 887VL2

USB 3.0 Box Header

SYS Fan

USB 2.0 x 2ATX-4P

SATA x 4

SATA DOM PWR

PWR/Reset/HDD LED

T: ATX/AT, B: COM2 RI

CPU Fan

DVI/HDMI

Debug Port

DIP Switch

LPT

K/B & MS

COM Box Header x 4

USB 3.0

LAN

LAN LED

VGA

4

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

This chapter describes how to set the jumpers and connectors on the PEAK 887VL2 motherboard.

Before You Begin

▪ Ensure you have a stable, clean working environment. Dust and dirt can

get into components and cause a malfunction. Use containers to keep small components separated.

▪ Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following: – A Philips screwdriver – A flat-tipped screwdriver – A set of jewelers screwdrivers – A grounding strap – An anti-static pad

▪ Using your fingers can disconnect most of the connections. It is

recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

▪ Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the electronic components. Humid environments tend to have less static electricity than

dry environments. A grounding strap is warranted whenever danger of static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪ Always disconnect the unit from the power outlet whenever you are

working inside the case.

▪ If possible, wear a grounded wrist strap when you are working inside the

computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance.

▪ Hold electronic circuit boards by the edges only. Do not touch the

components on the board unless it is necessary to do so. Don’t flex or stress the circuit board.

▪ Leave all components inside the static-proof packaging that they shipped

with until they are ready for installation.

▪ Use correct screws and do not over tighten screws.

5

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

Jumper Settings

A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open.

Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off).

Two-Pin Jumpers: Open (Left) and Short (Right)

Three-Pin Jumpers: Pins 1 and 2 are Short

3

2

1

3

2

6

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

CN7

Locations of the Jumpers and Connectors

The figure below shows the location of the jumpers and connectors for PEAK 887VL2.

CON1

J1

CN1

CN2 CN3

FAN1

CN13

FAN2

7

CN4

J2

CN5

J3

JP7

CN6

J4

JP5JP2

JP4

CN11 CN12

LAN1

LAN2

SW1

J5

CN9

JP8

PEAK 887VL2 User Manual

CN8 CN10

VGA1

Chapter 2: Jumpers and Connectors

Jumpers

CMOS Clear Select

Connector type: 1x3 3-pin header Connector location: JP7

1 3 1 3

Pin Settings

1-2 On Normal 2-3 On Clear BIOS Setting

1-2 On: default

AT/ATX Select

Connector type: 1x3 3-pin header Connector location: JP4

Pin Settings

1-2 On ATX Mode 2-3 On AT Mode

2-3 On: default

8

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

External Connectors

VGA Port

Connector type: DB-15 port, 15-pin D-Sub Connector location: VGA1

1

5

1115

Pin Definition Pin Definition

1 RED_VGA 2 GREEN_VGA 3 BLUE_VGA 4 NC 5 GND 6 GND 7 GND 8 GND

9 VGA_+5V 10 GND 11 NC 12 DDC_DATA_VGA 13 HSYNC_VGA 14 VSYNC_VGA 15 DDC_CLK_VGA MH1 CHASIS_GND

LAN1 Port

Connector type: RJ45 port with LEDs Connector location: LAN1

ACT LINK

18

Pin Definition Pin Definition

1 LAN2_MDI0P 2 LAN2_MDI0N 3 LAN2_MDI1P 4 LAN2_MDI1N 5 AVDD12_PHY2 6 LAN2TCTG 7 LAN2_MDI2P 8 LAN2_MDI2N

9 LAN2_MDI3P 10 LAN2_MDI3N 11 LAN2_LINK1G# 12 LAN2_LINK100# 13 LAN2_LED_ACT# 14 V_3P3_LAN

MH1 CHASIS_GND MH2 CHASIS_GND

9

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

LAN2 Port

Connector type: RJ45 port with LEDs Connector location: LAN2

ACT LINK

18

Pin Definition Pin Definition

1 LAN1_MDI0P 2 LAN1_MDI0N 3 LAN1_MDI1P 4 LAN1_MDI1N 5 AVDD12_PHY1 6 LAN1TCTG 7 LAN1_MDI2P 8 LAN1_MDI2N

9 LAN1_MDI3P 10 LAN1_MDI3N 11 LAN1_LINK1G# 12 LAN1_LINK100# 13 LAN1_LED_ACT# 14 V_3P3_LAN

MH1 CHASIS_GND MH2 CHASIS_GND

USB 3.0 Ports

Connector type: USB 3.0 port, Type A Connector location: CN11 and CN12

9

1

CN11

Pin Definition Pin Definition

1 P5V_OC23_C 2 USB_3N_C 3 USB_3P_C 4 GND 5 USB3_RX2_N_C 6 USB3_RX2_P_C 7 GND 8 USB3_TX2_N_C

9 USB3_TX2_P_C MH1 CHASIS_GND MH2 CHASIS_GND MH3 CHASIS_GND MH4 CHASIS_GND

CN12

Pin Definition Pin Definition

1 P5V_OC23_C 2 USB_2N_C

3 USB_2P_C 4 GND

5 USB3_RX1_N_C 6 USB3_RX1_P_C

7 GND 8 USB3_TX1_N_C

9 USB3_TX1_P_C MH1 CHASIS_GND MH2 CHASIS_GND MH3 CHASIS_GND MH4 CHASIS_GND

5

4

10

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

16

Internal Connectors

USB 3.0 Port

Connector type: 2x10 20-pin header, 2.0mm pitch Connector location: CN4

2 1

Pin Definition Pin Definition

1 P5V_OC01_C 2 USB3_RX4_N_C 3 USB3_RX4_P_C 4 GND 5 USB3_TX4_N_C 6 USB3_TX4_P_C 7 GND 8 USB_1N_R

9 USB_1P_R 10 USB3_ID 11 USB_0P_R 12 USB_0N_R 13 GND 14 USB3_TX3_P_C 15 USB3_TX3_N_C 16 GND 17 USB3_RX3_P_C 18 USB3_RX3_N_C 19 P5V_OC01_C

20 19

USB 2.0 Ports

Connector type: 1x6 6-pin header, 2.0mm pitch Connector location: J1 and J2

J1

Pin Definition Pin Definition

1 P5V_OC45_C 2 USB43 USB4+ 4 USB55 USB5+ 6 GND

J2

Pin Definition Pin Definition

1 P5V_OC45_C 2 USB63 USB6+ 4 USB75 USB7+ 6 GND

11

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

14

12

34

+12V Power Connector

Connector type: 2x2 4-pin header, 4.2mm pitch Connector location: CON1

Pin Definition Pin Definition

1 GND 2 GND

3 +12V 4 +12V

CPU FAN Connector

Connector type: 1x4 4-pin header, 2.54mm pitch Connector location: FAN1

Pin Definition Pin Definition

1 GND 2 +12V 3 FAN TAC 4 FAN CTL

12

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

14

16

System FAN Connector

Connector type: 1x4 4-pin header, 2.54mm pitch Connector location: FAN2

Pin Definition Pin Definition

1 GND 2 +12V

3 FAN TAC 4 FAN CTL

Keyboard and Mouse Connector

Connector type: 1x6 6-pin header, 2.0mm pitch Connector location: J5

Pin Definition Pin Definition

1 K/M_VCC 2 LKBDAT 3 LKBCLK 4 LMDAT 5 LMCLK 6 GND_BLK

13

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

COM1 Box Header Connector

Connector type: 2x5 10-pin header, 2.0mm pitch Connector location: CN10

2 1

Pin Definition Pin Definition

1 COM_DCD#1 2 COM_RXD1

3 COM_TXD1 4 COM_DTR#1

5 GND 6 COM_DSR#1

7 COM_RTS#1 8 COM_CTS#1

9 COM_RI#1 10 GND

10 9

COM2 Box Header Connector

Connector type: 2x5 10-pin header, 2.0mm pitch Connector location: CN7

2 1

Pin Definition Pin Definition

1 COM_DCD#2 2 COM_RXD2 4 COM_TXD2 4 COM_DTR#2 5 GND 6 COM_DSR#2 7 COM_RTS#2 8 COM_CTS#2 9 COM_RI#2_con 10 GND

10

9

14

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

COM3 Box Header Connector

Connector type: 2x5 10-pin header, 2.0mm pitch Connector location: CN8

2 1

Pin Definition Pin Definition

1 COM_DCD#3 2 COM_RXD3

3 COM_TXD3 4 COM_DTR#3

5 GND 6 COM_DSR#3

7 COM_RTS#3 8 COM_CTS#3

9 COM_RI#3 10 GND

10 9

COM4 Box Header Connector

Connector type: 2x5 10-pin header, 2.0mm pitch Connector location: CN9

2 1

Pin Definition Pin Definition

1 COM_DCD#4 2 COM_RXD4 3 COM_TXD4 4 COM_DTR#4 5 GND 6 COM_DSR#4 7 COM_RTS#4 8 COM_CTS#4 9 COM_RI#4 10 GND

10

9

15

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

1

14

13

26

12

23

Printer Port

Connector type: 2x13 26-pin header, 2.0mm pitch Connector location: CN3

Pin Definition Pin Definition

1 RPSTB 2 RPSTB0

3 RPSTB1 4 RPSTB2

5 RPSTB3 6 RPSTB4

7 RPSTB5 8 RPSTB6

9 RPSTB7 10 S1_LPTACK# 11 S1_LPTBUSY 12 S1_LPTPE 13 S1_LPTSLCT 14 S1_LPTAFD# 15 S1_LPTERR# 16 S1_LPTINIT# 17 S1_LPTSLIN# 18 GND_P1 19 GND_P1 20 GND_P1 21 GND_P1 22 GND_P1 23 GND_P1 24 GND_P1 25 GND_P1 26 NC

DVI/ HDMI Port Connector

Connector type: 2x15 30-pin header, 1.25mm pitch Connector location: CN13

9

0

Pin Definition Pin Definition

1 DPB_L0_P_R 2 HDMIB_PWR_R 3 DPB_L0_N_R 4 HDMIB_PWR_R 5 GND 6 DPB_PWR_R 7 DPB_L1_P_R 8 DPB_PWR_R

9 DPB_L1_N_R 10 HDMI_DIS 11 GND 12 HDMI_CTRL_CLK 13 DPB_L2_P_R 14 GND 15 DPB_L2_N_R 16 HDMI_CTRL_DATA 17 GND 18 GND 19 DPB_L3_P_R 20 GND 21 DPB_L3_N_R 22 GND 23 GND 24 HDMI_HPD 25 NC 26 GND 27 NC 28 DP_HPD 29 GND 30 GND

MH1 GND MH2 GND

16

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

SATA Connector

Connector type: Standard Serial ATAIII 7P (1.27mm, SATA-M-180) Connector location: CN1

1 7

Pin Definition Pin Definition

1 GND 2 R_SATA_TXP3 3 R_SATA_TXN3 4 GND 5 B_SATA_RXN3 6 B_SATA_RXP3 7 GND

SATA Connector

Connector type: Standard Serial ATAIII 7P (1.27mm, SATA-M-180) Connector location: CN2

1 7

Pin Definition Pin Definition

1 GND 2 R_SATA_TXP0

3 R_SATA_TXN0 4 GND

5 B_SATA_RXN0 6 B_SATA_RXP0

7 GND

17

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

SATA Connector

Connector type: Standard Serial ATAIII 7P (1.27mm, SATA-M-180) Connector location: CN5

1 17 7

Pin Definition Pin Definition

1 GND 2 R_SATA_TXP2 3 R_SATA_TXN2 4 GND 5 B_SATA_RXN2 6 B_SATA_RXP2 7 GND

SATA Connector

Connector type: Standard Serial ATAIII 7P (1.27mm, SATA-M-180) Connector location: CN6

Pin Definition Pin Definition

1 GND 2 R_SATA_TXP1 3 R_SATA_TXN1 4 GND 5 B_SATA_RXN1 6 B_SATA_RXP1 7 GND

18

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

15

COM2 RI# Voltage Select

Connector type: 1x5 5-pin header, 2.0mm pitch Connector location: JP5

Pin Definition Pin Definition

1 VCC5 2 COM_RI#2_con 3 +12V 4 COM_RI#2_con 5 COM_RI#2 6

SATA DOM Power Connector

Connector type: 1x2 2-pin header, 2.54mm pitch Connector location: J3

12

Pin Definition

1 VCC5 2 GND

19

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

17

28

11

21

LAN LED Pin Header

Connector type: 2x4 8-pin header, 2.00mm pitch Connector location: JP8

Pin Definition Pin Definition

1 LAN1_LED_ACT# 2 LAN2_LED_ACT# 3 V_3P3_LAN 4 V_3P3_LAN 5 LAN1_LINK1G# 6 LAN2_LINK1G# 7 LAN1_LINK100# 8 LAN2_LINK100#

Power On/Off/Reset & PWR/HDD LED Pin Header

Connector type: 2x8 16-pin header, 2.54mm pitch Connector location: JP2

6

5

Pin Definition Pin Definition

1 SATA_LED_P 2 PWR_LED_P 3 SATA_LED# 4 GND 5 GND 6 BTN_A# 7 RST_BTN# 8 GND

9 SPKR_OUT 10 SMB_CLK_MAIN 11 NC 12 SMB_DATA_MAIN 13 NC 14 S1_SYSTIN 15 SPKR_IN 16 SAHWGND

20

PEAK 887VL2 User Manual

Chapter 2: Jumpers and Connectors

11

DIP Switch

Connector type: 2x2 4-pin DIP switch Connector location: SW1

O

N

1

2

Pin Description

SW1.1

SW1.2

ON: Control by backplan OFF: Control by SW1.2 ON: PCIe x1 OFF: PCIe x4

Debug Port

Connector type: 1x10 10-pin header, 1.0mm pitch Connector location: J4

0

Pin Definition Pin Definition

1 GND 2 RST_SIO_N

3 CLK_PCI_P80 4 LPC_FRAME#

5 LPC_AD3 6 LPC_AD2

7 LPC_AD1 8 LPC_AD0

9 VCC3 10 VCC3

MH1 GND MH2 GND

21

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

This chapter describes how to use the BIOS setup program for the PEAK 887VL2. The BIOS screens provided in this chapter are for reference only and may change if the BIOS is updated in the future.

To check for the latest updates and revisions, visit the NEXCOM Web site at www.nexcom.com.tw.

About BIOS Setup

The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs. It is a ROM-based configuration utility that displays the system’s configuration status and provides you with a tool to set system parameters.

These parameters are stored in non-volatile battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS.

With easy-to-use pull down menus, you can configure such items as:

▪ Hard drives, diskette drives, and peripherals

▪ Video display type and display options

▪ Password protection from unauthorized use

▪ Power management features

The settings made in the setup program affect how the computer performs. It is important, therefore, first to try to understand all the setup options, and second, to make settings appropriate for the way you use the computer.

When to Configure the BIOS

▪ This program should be executed under the following conditions:

▪ When changing the system configuration

▪ When a configuration error is detected by the system and you are

prompted to make changes to the setup program

▪ When resetting the system clock

▪ When redefining the communication ports to prevent any conflicts

▪ When making changes to the Power Management configuration

▪ When changing the password or making other changes to the security

setup

Normally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the CMOS RAM has lost power, or the system features need to be changed.

22

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Default Configuration

Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering Setup

When the system is powered on, the BIOS will enter the Power-On Self Test (POST) routines. These routines perform various diagnostic checks; if an error is encountered, the error will be reported in one of two different ways:

▪ If the error occurs before the display device is initialized, a series of beeps

will be transmitted.

▪ If the error occurs after the display device is initialized, the screen will

display the error message.

Powering on the computer and immediately pressing <Del> allows you to enter Setup. Another way to enter Setup is to power on the computer and wait for the following message during the POST:

Legends

Key Function

Moves the highlight left or right to select a menu.

Moves the highlight up or down between sub-menus or fields.

Exits the BIOS Setup Utility.

Scrolls forward through the values or options of the highlighted field.

Scrolls backward through the values or options of the highlighted field.

Selects a field.

Displays General Help.

Load previous values.

Load optimized default values.

TO ENTER SETUP BEFORE BOOT PRESS

Press the

key to enter Setup:

Ctrl

+

Alt

+

23

Saves and exits the Setup program.

Press <Enter> to enter the highlighted sub-menu

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Scroll Bar

When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

Submenu

When “” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press .

24

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

BIOS Setup Utility

Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on the screen. The main menu allows you to select from several setup functions and one exit. Use arrow keys to select among the items and press to accept or enter the submenu.

Main

The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.

Advanced Chipset Boot SecurityMain

BIOS Information BIOS Vendor Core Version Compliancy BIOS Version Build Date and Time

Memory Information Memory Frequency Total Memory DIMM#0 DIMM#2

ME Firmware Information ME FW Version ME Firmware Mode ME Firmware SKU

System Date

System Time

American Megatrends

4.6.5.4 UEFI 2.3.1; PI 1.2 P887- 0.05 x64 09/03/2013 15:52:52

1600 Mhz 8192 MB (DDR3) Not Present 8192 MB (DDR3)

8.0.0.1351 Normal Mode 5MB

[Sun 09/02/2012] [19:47:48]

Save & Exit

Set the Date. Use Tab to switch between Date elements.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

System Date

The date format is <day>, <month>, <date>, <year>. Day displays a day, from Monday to Sunday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1999 to 2099.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.

25

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Advanced

The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Setting incorrect field values may cause the system to malfunction.

Advanced Chipset Boot SecurityMain

ACPI Settings

Trusted Computing

CPU Conguration SATA Conguration AMT Conguration USB Conguration IT8783F Super IO Conguration

IT8783F H/W Monitor Smart Fan Function Serial Port Console Redirection

Intel(R) Ethernet Network Connection i217-LM - 88:88:88: . . . Intel(R) I211 Gigabit Network Connection - 00:10:F3:2E: . . .

Save & Exit

System ACPI Parameters

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

ACPI Settings

This section is used to configure ACPI settings.

Advanced

ACPI Settings

Enable Hibernation

ACPI Sleep State

[Enabled]

[S3 only(Suspend to . . .]

Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable Hibernation

Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.

ACPI Sleep State

Select the highest ACPI sleep state the system will enter when the suspend button is pressed. The options are S1 (CPU Stop Clock) and S3 (Suspend to RAM).

26

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

CPU Configuration

This section is used to configure the CPU.

Advanced

CPU Conguration

Genuine Intel(R) CPU 0000 @ 2.60GHz

CPU Signature Processor Family Microcode Patch FSB Speed Max CPU Speed Min CPU Speed CPU Speed Processor Cores Intel HT Technology Intel VT-x Technology Intel SMX Technology 64-bit EIST Technology CPU C3 state CPU C6 state CPU C7 state

L1 Data Cache L1 Code Cache L2 Cache L3 Cache

306c2 6 ffff0006 100 MHz 2600 MHz 800 MHz 2800 MHz 4

Supported Supported Supported Supported Supported Supported Supported Supported

32 kB x 4 32 kB x 4 256 kB x 4 8192 kB

Enabled for Windows XP and

▲

Linux (OS optimized for HyperThreading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

▼

Advanced

FSB Speed Max CPU Speed Min CPU Speed CPU Speed Processor Cores Intel HT Technology Intel VT-x Technology Intel SMX Technology 64-bit EIST Technology CPU C3 state CPU C6 state CPU C7 state

L1 Data Cache L1 Code Cache L2 Cache L3 Cache

Hyper-threading

Active Processor Cores Limit CPUID Maximum Intel Virtualization Technology EIST Turbo Mode

100 MHz 2600 MHz 800 MHz 2800 MHz 4

Supported Supported Supported Supported Supported Supported Supported Supported

32 kB x 4 32 kB x 4 256 kB x 4 8192 kB

[Enabled]

[All] [Disabled] [Enabled] [Enabled] [Enabled]

▲

Enabled for Windows XP and Linux (OS optimized for HyperThreading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

▼

Hyper-Threading

This field is used to enable or disable hyper-threading.

Active Processor Cores

Select the number of cores to enable in each processor package.

Limit CPUID Maximum

The CPUID instruction of some newer CPUs will return a value greater than 3. The default is Disabled because this problem does not exist in the Windows series operating systems. If you are using an operating system other than Windows, this problem may occur. To avoid this problem, enable this field to limit the return value to 3 or lesser than 3.

Intel® Virtualization Technology

When this field is set to Enabled, the VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

EIST

Enables or disables Intel® SpeedStep.

Turbo Mode

Enables or disables turbo mode.

27

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

SATA Configuration

This section is used to configure the SATA drives.

Advanced

SATA Controller(s) [Enabled]

SATA Mode Selection [IDE] SATA Controller Speed [Gen2]

Serial ATA Port 0 Empty Software Preserve Unknown Serial ATA Port 1 Empty Software Preserve Unknown Serial ATA Port 2 Empty Software Preserve Unknown Serial ATA Port 3 Empty Software Preserve Unknown Serial ATA Port 4 Empty Software Preserve Unknown Serial ATA Port 5 Empty Software Preserve Unknown

SATA Controller(s)

Enables or disables the SATA controller.

Enable or disable SATA Device.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

SATA Mode Selection

Configures the SATA as IDE, AHCI or RAID mode.

IDE This option configures the Serial ATA drives as Parallel ATA physical storage device. RAID This option allows you to create RAID or Intel Matrix Storage configuration on Serial ATA devices. AHCI This option configures the Serial ATA drives to use AHCI (Advanced Host Controller Interface). AHCI allows the storage driver to enable the advanced Serial ATA features which will increase storage performance.

SATA Controller Speed

Configures the speed of the SATA controller.

28

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

AMT Configuration

This section is used to configure Active Management Technology (AMT) options.

Advanced

Intel AMT [Enabled]

Un-Congure ME [Disabled]

Disable ME [Disabled]

Enable/Disable Intel (R) Active Mangement Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires addtional

rmware in the SPI device.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Intel® AMT

Enables or disables Intel® Active Management Technology.

Un-Configure ME

Enables or disables Un-configure ME without password.

Disable ME

Set ME to Soft Temporary Disabled.

29

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

USB Configuration

This section is used to configure the USB.

Advanced

USB Conguration

USB Module Version

USB Devices: 2 Hubs

Legacy USB Support

USB3.0 Support XHCI Hand-off EHCI Hand-off USB Mass Storage Driver Support

8.10.27

[Enabled]

[Enabled] [Enabled] [Disabled] [Enabled]

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Legacy USB Support

Enable Enables Legacy USB. Auto Disables support for Legacy when no USB devices are connected. Disable Keeps USB devices available only for EFI applications.

XHCI Hand-off

This is a workaround for OSs that does not support XHCI hand-off. The XHCI ownership change should be claimed by the XHCI driver.

EHCI Hand-off

This is a workaround for OSs that does not support EHCI hand-off. The EHCI ownership change should be claimed by the EHCI driver.

USB Mass Storage Driver Support

Enables or disables USB mass storage driver support.

USB3.0 Support

Enables or disables USB 3.0 controller support.

30

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

IT8783F Super IO Configuration

This section is used to configure the I/O functions supported by the onboard Super I/O chip.

Advanced

IT8783F Super IO Conguration

IT8783F Super IO Chip



Serial Port 1 Conguration



Serial Port 2 Conguration



Serial Port 3 Conguration



Serial Port 4 Conguration



IR Device



Parallel Port Conguration

IT8783F

Set Parameters of Serial Port 1 (COMA)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

IT8783F Super IO Chip

Displays the Super I/O chip used on the board.

Serial Port 1 Configuration

This section is used to configure serial port 1.

Advanced

Serial Port 1 Conguration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=3F8h; IRQ=4;

[Auto]

Serial Port

Enables or disables the serial port.

Change Settings

Selects an optimal setting for the Super IO device.

Enable or Disable Serial Port (COM)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

31

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Serial Port 2 Configuration

This section is used to configure serial port 2.

Advanced

Serial Port 2 Conguration

Serial Port

Device Settings

Change Settings Onboard Serial Port 2 Mode Onboard Serial Port Max Baud Rate RS-485/422 receiver termination

[Enabled]

IO=2F8h; IRQ=3;

[Auto] [RS232] [115200 bps] [Disabled]

Serial Port

Enables or disables the serial port.

Enable or Disable Serial Port (COM)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Onboard Serial Port Max Baud Rate

Select this to change the max baud rate of the serial port.

RS-485/422 Receiver Termination

Enables or disables RS-485/422 receiver termination.

Change Settings

Selects an optimal setting for the Super IO device.

Onboard Serial Port 2 Mode

Select this to change the serial port mode to RS232, RS422 or RS485.

32

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Serial Port 3 Configuration

This section is used to configure serial port 3.

Advanced

Serial Port 3 Conguration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=3E8h; IRQ=10;

[Auto]

Serial Port

Enables or disables the serial port.

Enable or Disable Serial Port (COM)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Serial Port 4 Configuration

This section is used to configure serial port 4.

Advanced

Serial Port 4 Conguration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=2E8h; IRQ=11;

[Auto]

Serial Port

Enables or disables the serial port.

Enable or Disable Serial Port (COM)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Change Settings

Selects an optimal setting for the Super IO device.

Change Settings

Selects an optimal setting for the Super IO device.

33

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

IR Device

This section is used to configure the IR device.

Advanced

IR Device

Serial Port

[Disabled]

Serial Port

Enables or disables the serial port.

Enable or Disable Serial Port (COM)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Parallel Port Configuration

This section is used to configure the parallel port.

Advanced

Parallel Port Conguration

Parallel Port

Device Settings

Change Settings Device Mode

[Enabled]

IO=378h;

[IO=378h;] [Standard Parallel P. . .]

Parallel Port

Enables or disables the parallel port.

Enable or Disable Parallel Port (LPT/LPTE)

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Change Settings

Selects an optimal setting for the Super IO device.

Device Mode

Configures the operating mode of the parallel port. The options are Standard Parallel Port Mode, EPP Mode, ECP Mode, EPP Mode & ECP Mode.

34

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

IT8783F H/W Monitor

This section is used to monitor hardware status such as temperature, fan speed and voltages.

Advanced

Pc Health Status

SYS temperature CPU temperature System temperature3 Fan2 Speed Fan1 Speed Vcore

3.3V 5V 12V

: +30 C : +30 C : N/A : 4166 RPM : N/A : +1.760 V : +3.192 V : +5.107 V : +11.816 V

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

SYS Temperature

Detects and displays the current system temperature.

Fan2 Speed

Detects and displays system fan2 speed.

Fan1 Speed

Detects and displays system fan1 speed.

Vcore

Detects and displays the Vcore CPU voltage.

3.3V

Detects and displays 3.3V voltage.

5V

Detects and displays 5V voltage.

12V

Detects and displays 12V voltage.

CPU Temperature

Detects and displays the current CPU temperature.

System Temperature3

Detects and displays the current temperature of system 3.

35

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Smart Fan Function

This section is used to configure the fan’s function.

Advanced

Pc Health Status

FAN Setting

[Always Full Speed]

FAN Setting

Configures the speed of the fan.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Serial Port Console Redirection

Specifies how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Advanced

COM0 (Disabled) Console Redirection

COM1 (Pci Bus0, Dev0, Func0) (Disabled) Console Redirection

Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS)

Console Redirection



Console Redirection Settings

Port Is Disabled

[Enabled]

Console Redirection Enable or Disable.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Console Redirection

Configures the speed of the fan.

36

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Chipset

This section is used to configure the system based on the specific features of the chipset.

Advanced

PCH-IO Conguration

System Agent (SA) Conguration

Chipset Boot SecurityMain

Setting incorrect field values may cause the system to malfunction.

Save & Exit

PCH Parameters

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

PCH-IO Configuration

Advanced

Intel PCH RC Version Intel PCH SKU Name Intel PCH Rev ID

USB Conguration

PCH Azalia Conguration BIOS Security Conguration

Toggle EC PCH LAN Controller Wake on LAN Restore AC Power Loss

Chipset Boot SecurityMain

1.5.0.0 Q87 05/C2

[Disabled] [Enabled] [Enabled] [Power On]

Toggle EC

Enables or disables Toggle EC.

PCH LAN Controller

Enables or disables onboard NIC.

Save & Exit

USB Conguration

settings

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Wake on LAN

Enables or disables integrated LAN to wake the system.

Restore AC Power Loss

Select AC power state when power is re-applied after a power failure.

37

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

System Agent (SA) Configuration

Advanced

System Agent Bridge Name System Agent RC Version VT-d Capability

VT-d

Graphics Conguration NB PCIe Conguration Memory Conguration

Chipset Boot SecurityMain

Haswell

1.5.0.0 Supported

[Enabled]

VT-d

Enables or disables VT-d function on MCH.

Graphics Configuration

Configures the graphic chip settings.

NB PCIe Configuration

Configures the NB PCI Express settings.

Memory Configuration

Configures the memory settings.

Save & Exit

Check to enable VT-d function on MCH.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Boot

This section is used to configure the boot features.

Advanced

Quiet Boot Fast Boot

Boot Option Priorities

CSM parameters

Chipset

Boot

[Disabled] [Disabled]

SecurityMain

Quiet Boot

Enabled Displays OEM logo instead of the POST messages. Disabled Displays normal POST messages.

Fast Boot

Enables or disables boot with initialization of a minimal set of devices required to launch active boot option. Has no effect for BBS boot options.

Boot Option Priorities

Adjust the boot sequence of the system. Boot Option #1 is the first boot device that the system will boot from, next will be #2 and so forth.

CSM Parameters

Parameters for OpROM execution, boot options, filter, etc.

Save & Exit

OpROM execution, boot options

lter, etc.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

38

PEAK 887VL2 User Manual

Chapter 3: BIOS Setup

Security

Advanced Chipset Boot SecurityMain

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User Will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20

Administrator Password

User Password

Administrator Password

Select this to reconfigure the administrator’s password.

User Password

Select this to reconfigure the user’s password.

Save & Exit

Set Administrator Password

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Save & Exit

Advanced

Save Changes and Reset

Discard Changes and Reset

Restore Defaults

Save Changes and Reset

To save the changes and reset, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Discard Changes and Reset

To exit the Setup utility and reboot the system without saving the changes, select this field then press <Enter>. You may be prompted to confirm again before exiting.

Chipset

Boot SecurityMain

Save & Exit

Reset the system after saving the changes.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Restore Defaults

To restore the BIOS to default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

39

PEAK 887VL2 User Manual

NEXCOM PEAK 887VL2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual