Nexcom OPPC 1540HT-J1900, OPPC 1940HT-J1900 User Manual

NEXCOM International Co., Ltd.

Published August 2017

www.nexcom.com

IoT Automation Solutions Business Group

Open Frame Panel PC OPPC 1540HT-J1900/1940HT-J1900

User Manual

ii

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Content

Contents

Preface

Copyright ............................................................................................. iv

Disclaimer .............................................................................................. iv

Acknowledgements ............................................................................... iv

Regulatory Compliance Statements ........................................................ iv

Declaration of Conformity ...................................................................... iv

RoHS Compliance ................................................................................... v

Warranty and RMA ................................................................................ vi

Safety Information ................................................................................. ix

Installation Recommendations ................................................................ ix

Safety Precautions ................................................................................... x

Technical Support and Assistance ........................................................... xi

Conventions Used in this Manual ........................................................... xi

Global Service Contact Information ........................................................xii

Package Contents .................................................................................xiv

Ordering Information .............................................................................xv

Chapter 1: Product Introduction

OPPC 1540HT-J1900 ...............................................................................1

Specifications ..........................................................................................2

OPPC 1940HT-J1900 ...............................................................................4

Specifications ..........................................................................................5

Knowing Your OPPC Series .....................................................................7

Rear Bottom ........................................................................................7

Rear ....................................................................................................8

Mechanical Dimensions ...........................................................................9

OPPC 1540HT-J1900 ...........................................................................9

OPPC 1940HT-J1900 .........................................................................10

Chapter 2: Jumpers and Connectors

Before You Begin ..................................................................................11

Precautions ..........................................................................................11

Jumper Settings ....................................................................................12

Locations of the Jumpers and Connectors .............................................13

Top View ...........................................................................................13

Bottom View ..................................................................................... 14

Jumpers and DIP Switch Settings ...........................................................15

RTC and SRTC Clear Select ............................................................. 15

AT/ATX Power Select ......................................................................15

Dimming Signal Level Select ...........................................................16

LCD Panel VDD Power Select ..........................................................16

Touch 4/5 Wire Select .....................................................................17

COM1 RI Pin Power Select ..............................................................17

COM2 RI Pin Power Select ..............................................................18

Panel Resolution Select ...................................................................18

Dimming Type Select ......................................................................19

Connector Pin Definitions .....................................................................20

External I/O Interfaces ........................................................................ 20

Line-out Connector ........................................................................20

Remote Power On/Off Switch .........................................................20

LAN1 Port ......................................................................................21

iii

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Content

LAN2 Port ......................................................................................21

Dual USB 2.0 Port ..........................................................................22

Single USB 3.0 Port ........................................................................22

COM1 Port ....................................................................................23

COM2 Port ....................................................................................23

VGA Port .......................................................................................24

12V - 30V DC Power Input .............................................................24

CFast Card Slot ..............................................................................25

Reset Button ..................................................................................25

Internal Connectors ........................................................................... 26

CCFL Panel Backlight Connector ....................................................26

LVDS Channel A .............................................................................26

LVDS Channel B .............................................................................27

Line-in/Mic-in Connector ................................................................27

Speaker-out Connector ..................................................................28

USB Connector ..............................................................................28

Touch Sensor Connector ................................................................29

SATA Connector .............................................................................29

SATA DOM Power Connector .........................................................30

DIO Connector (Optional) ...............................................................30

Keyboard/Mouse Connector ...........................................................31

Active LED Connector ....................................................................31

Power Button .................................................................................32

Backlight Control Input Connector .................................................32

Dimming Control Input Connector .................................................33

LVDS MCU FW Debug Connector ...................................................33

Smart Fan Connector .....................................................................34

Battery Connector ..........................................................................34

Post Code Debug Connector ..........................................................35

SIM Card Slot .................................................................................35

Mini-PCIe Slot ................................................................................36

Mini-PCIe Slot (Wi-Fi/3G) ................................................................ 37

Block Diagram ......................................................................................38

Chapter 3: System Setup

Installing a SATA Hard Drive ..................................................................39

Installing a CFast Card ..........................................................................43

Installing a SO-DIMM Memory Module .................................................45

Installing a SATA DOM ..........................................................................46

Installing a Mini PCIe Module ................................................................50

Installing the Front Bezel on OPPC 1540HT-J1900 (Optional) .................54

Installing the Front Bezel on OPPC 1940HT-J1900 (Optional) .................58

Plugging the DC Power Cable ...............................................................61

Panel Mounting ....................................................................................62

Panel Mount Kit (Optional) ....................................................................63

Front Bezel Design Guide ......................................................................65

Open Frame Mount ..............................................................................66

Chapter 4: BIOS Setup

About BIOS Setup .................................................................................67

When to Configure the BIOS .................................................................67

Default Configuration ...........................................................................68

Entering Setup ......................................................................................68

Legends ................................................................................................68

BIOS Setup Utility ..................................................................................70

Main .................................................................................................70

Advanced .........................................................................................71

Chipset ..............................................................................................79

Security .............................................................................................82

Boot ..................................................................................................82

Save & Exit ........................................................................................84

iv

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

PrefaCe

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co., Ltd. However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom.com. NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

OPPC 1540HT-J1900 and OPPC 1940HT-J1900 are trademarks of NEXCOM International Co., Ltd. All other product names mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense.

CE

The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.

v

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status Update

NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green

products and services, which are compliant with European Union RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment) directive 2011/65/EU, to be your trusted green partner and to protect our environment.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force to implement the introduction of green products. The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2013 will be RoHS compliant. They will use the usual NEXCOM naming convention.

vi

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Warranty and RMA

NEXCOM Warranty Period

1. NEXCOM makes products in accordance with the Industry standard and,

NEXCOM warrants that all her Industry-grade IPC and System products will be free from defect in neither material nor workmanship for twentyfour (24) months from the day of invoice issued.

2. For NEXCOM Panel PC product lines (the APPC, MPPC series), they are

also guaranteed against defect in materials and workmanship for the period of twenty-four (24) months in their motherboard design. For 3rd party parts, it follows with original suppliers’ standard: 12 months for battery pack and LCD, 24 months for adaptor / add on modules (including GSM module, RFID module, and antenna).

3. If NEXCOM determines customer’s warranty claim is valid, NEXCOM

will repair or replace product(s) without additional charge for parts and labor. An extended Warranty Program will extend the warranty period of the product accordingly.

Warranty Coverage

The warranty applies only to products manufactured or distributed by NEXCOM and her subsidiaries. This warranty covers all the products/ shipments except for:

1. Any claimed defect, products that have been repaired or modified by

persons who have not been authorized by NEXCOM or, products which have been subjected to misuse, abuse, accident, improper installation, or usage not in accordance with the product instruction. NEXCOM assumes no liability as a consequence of such events under the term of this warranty.

One example is the replacement of Tablet’s or Hand-held’s LCD display

due to scratching stains or other degradation; these will not be covered under this warranty.

2. Damages caused by customers’ delivery/shipping of the product or, product failure resulted from electrical power/voltage shock, or, installation of parts/components which are not supplied/approved by NEXCOM in advance.

3. Third-party products:

a. Software, such as the device drivers,

b. External devices such as HDD, printer, scanner, mouse, LCD panel,

battery, and so on,

c. Accessory/parts that were not approved by NEXCOM and,

d. Accessory/parts were added to products after they were shipped

from NEXCOM.

Product will be treated as “Out of Warranty “ if:

a. It expires the warranted 24 months period from the day it was purchased.

b. It had been altered by persons other than an authorized NEXCOM

service person or, which have been subjected to misuse, abuse, accident, or improper installation.

c. It doesn’t have the original NEXCOM Serial Number labeling for

NEXCOM’s warranty period identification or, tracking.

vii

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

RMA that NEXCOM has determined not to be covered by the warranty will be charged the NEXCOM Standard Repair Fee for the repairing. If a RMA is determined to be not repairable, customer will be notified and product(s) may be returned to customer at their request; a minimum service fee may be charged however.

NEXCOM Return Merchandise Authorization (RMA) Procedure

For the RMA (Return Merchandise Authorization) shipment, customer is responsible for packaging and shipping the product to the designated NEXCOM service sites, with shipping charges prepaid by the customer. The original NEXCOM shipping box should be used whenever possible. NEXCOM shall pay for the return of the product to the customer’s location. In case of expedited shipping request, an extra service charge shall be assessed and the customer is responsible for this extra return shipping charge.

1. Customers should enclose the “NEXCOM RMA Service Form” with the returned products.

2. Customers need to write down all the information related to the problem on the “ NEXCOM RMA Service Form “ when applying for the RMA service; information will help to understand the problem, including the fault description, on-screen messages, and pictures if possible.

3. Customers could send back the faulty product with or without the accessories and key parts such as the CPU and DIMM. If the key parts are included, please be noted clearly within the return form. NEXCOM takes no responsibility for the parts which are not listed in the return form.

4. Customers hold the responsibility to ensure that the packing of defective products is durable enough to be resistant against further damage due to the transportation; damage caused by transportation is treated as “ Out of Warranty “ under our Warranty specification.

5. RMA product(s) returned by NEXCOM to any location other than the

customer registered delivery address will incur an extra shipping charge, the customer is responsible for paying the extra shipping charges, duties, and taxes of this shipment.

Product Repairing

1. NEXCOM will repair defective products covered under this limited warranty that are returned to NEXCOM; if products do prove to be defective, they will be repaired during their warranty period unless other warranty terms have been specified.

2. NEXCOM owns all parts removed from repaired products.

3. NEXCOM will use parts made by various manufacturers in performing the repair.

4. The repaired products will be warranted subjected to the original warranty coverage and period only.

5. For products returned as defective but, proved to be no defect/fault after the RMA process, NEXCOM reserves the right to claim for a NDF (No Defect Found) Service Charge.

6. NEXCOM will issue RMA Report which included Repair Detailed Information to the customer when the defective products were repaired and returned.

7. In addition to the above, NEXCOM may authorize Independent/Thirdparty suppliers to repair the defective products for NEXCOM.

viii

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Out Of Warranty Service

There will be a service charge from NEXCOM for the “Out Of Warranty” product service; they are the Basic Diagnostic Service Fee and the Advanced Component Replacement Fee respectively. And, if the product can not be repaired, NEXCOM will either return the product to the customer or, just scrap it, followed by customer’s instruction.

1. Testing and Parts Replacement

NEXCOM will have the following Handling Charges for those OoW

products that returned:

a. Basic Labor Cost and Testing Fee: as Table listed.

b. Parts Fee: NEXCOM will charge for main IC chipsets such as the N.B.,

S.B., Super-IO, LAN, Sound, Memory, and so on.

c. 3rd-party Device Fee: products replacement for CPU, DIMM, HDD,

Chassis, and UPS.

2. Out of Warranty product will have a three months warranty for the fixed issues. If the product failed with different problem within 3 months, they will still incur the service charge of “Out of Warranty”.

3. Out of Warranty “products will not be repaired without a signed PI from the customer, the agreement of the repair process.

Add-on card, 3rd Party Device and board level repair cost higher than

new product prices, customer can abandon to sign PI to repair and, please contact with sales to buy new products.

ix

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated.

Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:

▪ A Philips screwdriver

▪ A flat-tipped screwdriver

▪ A grounding strap

▪ An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

Safety Information

Before installing and using the device, note the following precautions:

▪ Read all instructions carefully.

▪ Do not place the unit on an unstable surface, cart, or stand.

▪ Follow all warnings and cautions in this manual.

▪ When replacing parts, ensure that your service technician uses parts

specified by the manufacturer.

▪ Avoid using the system near water, in direct sunlight, or near a heating

device.

▪ The load of the system unit does not solely rely for support from the

rackmounts located on the sides. Firm support from the bottom is highly necessary in order to provide balance stability.

▪ The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

x

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a

damp cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a stable surface during installation. Dropping it or

letting it fall may cause damage.

7. The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting

the equipment to the power outlet.

9. Place the power cord in a way so that people will not step on it. Do not

place anything on top of the power cord. Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product’s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work

according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15. Do not place heavy objects on the equipment.

16. The unit uses a three-wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does not support this kind of plug, contact your electrician to replace your obsolete outlet.

17. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

xi

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or sales representative, please have the following information ready before calling: – Product name and serial number – Detailed information of the peripheral devices – Detailed information of the installed software (operating system,

version, application software, etc.) – A complete description of the problem – The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth.

3. CFast: Turn off the unit’s power before inserting or removing a CFast storage card.

Conventions Used in this Manual

Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task.

CAUTION!

CAUTION!CAUTION!

Caution: Information to avoid damaging components or losing data.

Note: Provides additional information to complete a task easily.

xii

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

9F, No. 920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7786 Fax: +886-2-8226-7782 www.nexcom.com

America

USA NEXCOM USA

2883 Bayview Drive, Fremont CA 94538, USA Tel: +1-510-656-2248 Fax: +1-510-656-2158 Email: sales@nexcom.com www.nexcom.com

Asia

Taiwan NEXCOM Intelligent Systems

Taipei Office

13F, No.920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7796 Fax: +886-2-8226-7792 Email: sales@nexcom.com.tw www.nexcom.com.tw

NEXCOM Intelligent Systems Taichung Office

16F, No.250, Sec. 2, Chongde Rd., Beitun Dist., Taichung City 406, R.O.C. Tel: +886-4-2249-1179 Fax: +886-4-2249-1172 Email: sales@nexcom.com.tw www.nexcom.com.tw

Japan NEXCOM Japan

9F, Tamachi Hara Bldg., 4-11-5, Shiba Minato-ku, Tokyo, 108-0014, Japan Tel: +81-3-5419-7830 Fax: +81-3-5419-7832 Email: sales@nexcom-jp.com www.nexcom-jp.com

China

NEXCOM China

Floor 5, No.4, No.7 fengxian middle Rd., (Beike Industrial Park), Haidian District, Beijing, 100094, China Tel: +86-10-5704-2680 Fax: +86-10-5704-2681 Email: sales@nexcom.cn www.nexcom.cn

xiii

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Europe

United Kingdom NEXCOM EUROPE

10 Vincent Avenue, Crownhill Business Centre, Milton Keynes, Buckinghamshire MK8 0AB, United Kingdom Tel: +44-1908-267121 Fax: +44-1908-262042 Email: sales.uk@nexcom.eu www.nexcom.eu

Italy NEXCOM ITALIA S.r.l

Via Lanino 42, 21047 Saronno (VA), Italia Tel: +39 02 9628 0333 Fax: +39 02 9625 570 Email: nexcomitalia@nexcom.eu www.nexcomitalia.it

NEXCOM Shanghai

Room 603/604, Huiyinmingzun Plaza Bldg., 1, No.609, Yunlin East Rd., Shanghai, 200333, China Tel: +86-21-5278-5868 Fax: +86-21-3251-6358 Email: sales@nexcom.cn www.nexcom.cn

NEXCOM Surveillance Technology Corp.

Room202, Building B, the GuangMing Industrial Zone Zhonghua Rd., Minzhi Street, Longhua District, Shenzhen 518131, China Tel: +86-755-8364-7768 Fax: +86-755-8364-7738 Email: steveyang@nexcom.com.tw www.nexcom.cn

NEXCOM United System Service

Hui Yin Ming Zun Building Room 1108, Building No. 11, 599 Yunling Road, Putuo District, Shanghai, 200062, China Tel: +86-21-6125-8282 Fax: +86-21-6125-8281 Email: frankyang@nexcom.cn www.nexcom.cn

xiv

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Package Contents

Before continuing, verify that the package you received is complete. Your OPPC 1540HT-J1900/1940HT-J1900 package should have all the items listed in the table.

Item Description Qty

1 Driver CD 1 2 Flat Head for HDD Installation 4 3 Panel Mount Kit 8

OPPC 1940HT-J1900

Item Description Qty

1 Driver CD 1 2 Flat Head for HDD Installation 4 3 Panel Mount Kit 10

OPPC 1540HT-J1900

Note: Package contents may vary depending on your country region, some items may be optional. Please contact your local distributor for more information.

Panel Mount Kit

(OPPC 1540HT-J1900)

Panel Mount Kit

(OPPC 1940HT-J1900)

Driver CD

Flat Head Screw

xv

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Preface

Ordering Information

The following information below provides ordering information for the Open Frame Panel PC series.

Barebone

• OPPC 1540HT-J1900 (P/N: 90IQ1540H00X0)

15” XGA LED backlight touch Panel PC with Intel

®

Celeron™ J1900,

2.0GHz, 1000 nits, touch screen, 4GB DDR3L with 2x RS232/422/485

• OPPC 1940HT-J1900 (P/N: 90IQ1940H00X0)

19” SXGA LED backlight touch Panel PC with Intel

®

Celeron™ J1900,

2.0GHz, 1000 nits, touch screen, 4GB DDR3L with 2x RS232/422/485

• 12V, 60W AC/DC power adapter w/o power cord (P/N: 7400060031X00)

Optional

1

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

ChaPter 1: ProduCt IntroduCtIon

Key Features

▪ 4:3 15” XGA Fanless Panel Computer

▪ Intel

®

Celeron™ J1900, Quad core, low power consumption

▪ 1000 nits High brightness

▪ Flush Panel by 5-wire Touch Screen

▪ PS2 KB/MS/Line-out/Dual GbE/3x USB

▪ 2x RS232/422/485/2nd display-VGA/1x Mini-PCIe socket/1x CFast

▪ Remote power switch

▪ DDR3L 4GB/2.5” HDD bracket

▪ Support JMobile HMI, Citect SCADA and CODESYS SoftLogic (optional)

▪ Mounting support: Panel/Wall/Stand/VESA 100mm x 100mm

▪ Wide range power input 12V~ 30V DC

OPPC 1540HT-J1900

Overview

2

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Specifications

Panel

▪ LED size: 15”, 4:3 ▪ Resolution: XGA 1024x768 ▪ Luminance: 1000cd/m² ▪ Contrast ratio: 2500 ▪ LCD color: 16.2M ▪ Viewing angle: 88(U), 88(D), 88(L), 88(R) ▪ Backlight: LED

Touch Screen

▪ 5-wire resistive (flush panel type) ▪ Touch light transmission: 81% ▪ Touch interface: USB

System

▪ CPU: On-board Intel® Celeron™, Quad core processor J1900, 2.0GHz,

2M L2 Cache ▪ BIOS: AMI BIOS ▪ System memory: 2x 204-pin DDR3L SO-DIMM socket, 4GB DDR3L

(Default), Support up to 8GB DDR3L-1066/1333, Non-ECC and

Unbuffered ▪ Storage device:

– 1x external locked CFast socket – 1x hard drive bay: optional 1x 2.5” SATA HDD or 1x SATA DOM

▪ Watchdog timer: Watchdog timeout can be programmed by software

from 1 second to 255 seconds and from 1 minute to 255 minutes

(Tolerance 15% under room temperature 25°C) ▪ H/W status monitor: monitoring system temperature, and voltage ▪ Expansion: 2x Mini-PCIe sockets (support optional Wi-Fi, 3.5G module)

Rear I/O

▪ PS2 keyboard/mouse ▪ Audio port: 1x Line-out ▪ Remote power switch ▪ Ethernet: 2x RJ45 ▪ USB: 2x USB 2.0; 1x USB 3.0 ▪ COM #1: RS232/422/485 ▪ COM #2: RS232/422/485 ▪ Reset button ▪ 2nd display VGA port: 1x DB15 ▪ Power switch

Audio

▪ AC97 codec: Realtek ALC886-GR ▪ Audio interface: Line-out/Line-in (Optional)/MIC-in (Optional) audio Jack

Ethernet

▪ LAN chip: dual Intel® I210AT Gigabit LAN ▪ Ethernet interface: 10/100/1000 Based-Tx Ethernet compatible

Mechanical & Environment

▪ Mounting: panel/wall/stand/VESA 100mm x 100mm ▪ Power input: 12V~30V DC ▪ Power adapter: Optional AC to DC power adaptor (+12V, 60W) ▪ Vibration:

– IEC 68 2-64 (w/ HDD) – 1Grms @ sine, 5~500Hz, 1hr/axis (HDD operating) – 2Grms @ sine, 5~500Hz, 1hr/axis (CFast operating) – 2.2Grms @ random condition, 5~500Hz, 0.5hr/axis (non-operating)

3

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

▪ Shock:

– IEC 68 2-27

– HDD: 20G@wall mount, half sine, 11ms ▪ Operating temperature: -5°C to 50°C ▪ Storage temperature: -20°C to 75°C ▪ Operating humidity: 10%~90% relative humidity, non-condensing ▪ Dimension: 329 x 280 x 69.3mm ▪ Weight: 4kg

Certifications

▪ CE approval ▪ FCC Class A

4

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Key Features

▪ 4:3 19” SXGA Fanless Panel Computer

▪ Intel

®

Celeron™ J1900, Quad core, low power consumption

▪ 1000 nits High brightness

▪ Flush Panel by 5-wire Touch Screen

▪ PS2 KB/MS/Line-out/Dual GbE/3x USB

▪ 2x RS232/422/485/2nd display-VGA/1x Mini-PCIe sockets/1x CFast

▪ Remote power switch

▪ DDR3L 4GB/2.5” HDD bracket

▪ Support JMobile HMI, Citect SCADA and CODESYS SoftLogic (optional)

▪ Mounting support: Panel/Wall/Stand/VESA 100mm x 100mm

▪ Wide range power input 12V~ 30V DC

OPPC 1940HT-J1900

5

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Specifications

Panel

▪ LED size: 19”, 4:3 ▪ Resolution: SXGA 1280x1024 ▪ Luminance: 1000cd/m² ▪ Contrast ratio: 1000:1 ▪ LCD color: 16.7M ▪ Viewing angle: 80(U), 80(D), 85(L), 85(R) ▪ Backlight: LED

Touch Screen

▪ 5-wire resistive (flush panel type) ▪ Touch light transmission: 80% ▪ Touch interface: USB

System

▪ CPU: On-board Intel® Celeron™, Quad core processor J1900, 2.0GHz,

2M L2 Cache ▪ BIOS: AMI BIOS ▪ System memory: 2x 204-pin DDR3L SO-DIMM socket, 4GB DDR3L

(Default), Support up to 8GB (4GB+4GB) DDR3L-1066/1333, Non-ECC

and Un-buffered ▪ Storage device:

– 1x external locked CFast socket – 1x hard drive bay: optional 1x 2.5” SATA HDD or 1x SATA DOM

▪ Watchdog timer: Watchdog timeout can be programmed by software

from 1 second to 255 seconds and from 1 minute to 255 minutes

(Tolerance 15% under room temperature 25°C) ▪ H/W status monitor: monitoring system temperature, and voltage ▪ Expansion: 1x Mini-PCIe socket1 (support optional Wi-Fi, 3.5G module)

Rear I/O

▪ PS2 keyboard/mouse ▪ Audio port: 1x Line-out ▪ Remote power switch ▪ Ethernet: 2x RJ45 ▪ USB: 2x USB 2.0; 1x USB 3.0 ▪ COM #1: RS232/422/485 ▪ COM #2: RS232/422/485 ▪ Reset button ▪ 2nd display VGA port: 1x DB15 ▪ Power switch

Audio

▪ AC97 codec: Realtek ALC886-GR ▪ Audio interface: Line-out/Line-in (Optional)/Mic-in (Optional) audio Jack

Ethernet

▪ LAN chip: dual Intel® I210AT Gigabit LAN ▪ Ethernet interface: 10/100/1000 Based-Tx Ethernet compatible

Mechanical & Environment

▪ Mounting: panel/wall/stand/VESA 100mm x 100mm ▪ Power input: 12V~30V DC ▪ Power adapter: Optional AC to DC power adaptor (+12V, 60W) ▪ Vibration:

– IEC 68 2-64 (w/ HDD) – 1Grms @ sine, 5~500Hz, 1hr/axis (HDD operating) – 2Grms @ sine, 5~500Hz, 1hr/axis (CFast operating) – 2.2Grms @ random condition, 5~500Hz, 0.5hr/axis (non-operating)

6

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

▪ Shock:

– IEC 68 2-27

– HDD: 20G@wall mount, half sine, 11ms ▪ Operating temperature: -5°C to 50°C ▪ Storage temperature: -20°C to 75°C ▪ Operating humidity: 10%~90% relative humidity, non-condensing ▪ Dimension: 422.6(W) x 350.6(H) x 73.2(D)mm ▪ Weight: 6.15Kg

Certifications

▪ CE approval ▪ FCC Class A

7

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Knowing Your OPPC Series

Rear Bottom

LAN 1

VGA

12V-30V

DC Input

Remote

On/Off

LAN 2 COM 1 Reset

Line-outPS/2 KB/MS COM 2USB 3.0

USB 2.0

PS/2 KB/MS

Used to connect a PS/2 keyboard or a PS/2 mouse.

Line-out

Used to connect a headphone or a speaker.

Remote On/Off Switch

Used to connect a remote to power on/off the system.

LAN 1 and LAN 2

Used to connect the system to a local area network. LAN 1 supports Wake up on LAN.

USB 2.0

Dual USB 2.0 port for connecting USB 2.0/1.1 devices.

USB 3.0

Single USB 3.0 port for connecting the system with USB 3.0/2.0 devices.

COM 1 and COM 2

These COM ports support RS232/422/485 compatible series device through BIOS setting, and have 2.5kV isolated protection.

Reset Button

Press this button to restart the system.

VGA

Used to connect an analog VGA monitor.

12V-30V DC Input

Used to plug a DC power cord.

8

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Rear

VESA Mounting Hole

(100x100mm)

VESA Mounting Hole

(100x100mm)

VESA Mounting Hole

(75x75mm)

VESA Mounting Hole

(75x75mm)

VESA Mounting Hole

(100x100mm)

VESA Mounting Hole

(100x100mm)

VESA Mounting Hole

(75x75mm)

VESA Mounting Hole

(75x75mm)

VESA Mounting Holes

These are the mounting holes for VESA mounting (100x100mm and 75x75mm)

9

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Mechanical Dimensions

353

280

90 100 90

7575 6060

Ø4.50

12

304.10 (LCD Active Area)

228.10 (LCD Active Area)

24.45

25.95

10

170

10

90 120 90

174.30

12

256

40.85

12

27.50

16

150 53

75

100

75

100

8-M4-VESA HOLES

270

69.30

329

67.25 67.25

47.50

12

16

16084.50

334 ±0.5

261 ±0.5

7 max.

CUT OUT SIZE T=7mm(MAX)

OPPC 1540HT-J1900

10

Chapter 1: Product Introduction

OPPC 1540HT-J1900/1940HT-J1900 User Manual

46.30 110

100

110 46.30

4.50

4.50x12L

80.305570

55

80.30

422.60 ±0.3

350.60 ±0.3

376.32 (Panel Active Area)

301.06 (Active Area)

150150

160

378.32 ±0.3 (Viewing CUT OUT Size)

303.06 ±0.3 (Viewing CUT OUT Size)

10

22.14

23.87

67.25 67.25

54

326.60 ±0.3

174.30

34

75.80

21.50

150 88.30

398.60 ±0.3

270

41.80

75.80

120120

75

100

100 75

8-M4-VESA MOUNT

403 ±0.5

331 ±0.5

7 max.

CUT OUT SIZE T=7mm(MAX)

OPPC 1940HT-J1900

11

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

ChaPter 2: JumPers and ConneCtors

This chapter describes how to set the jumpers and connectors on the motherboard. Note that information in this chapter applies to OPPC 1540HTJ1900 and OPPC 1940HT-J1900.

Before You Begin

▪ Ensure you have a stable, clean working environment. Dust and dirt can

get into components and cause a malfunction. Use containers to keep small components separated.

▪ Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following: – A Philips screwdriver – A flat-tipped screwdriver – A set of jewelers screwdrivers – A grounding strap – An anti-static pad

▪ Using your fingers can disconnect most of the connections. It is

recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

▪ Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the electronic

components. Humid environments tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪ Always disconnect the unit from the power outlet whenever you are

working inside the case.

▪ If possible, wear a grounded wrist strap when you are working inside the

computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance.

▪ Hold electronic circuit boards by the edges only. Do not touch the

components on the board unless it is necessary to do so. Don’t flex or stress the circuit board.

▪ Leave all components inside the static-proof packaging that they shipped

with until they are ready for installation. Use correct screws and do not over tighten screws.

12

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Jumper Settings

A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open.

Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off).

Two-Pin Jumpers: Open (Left) and Short (Right)

Three-Pin Jumpers: Pins 1 and 2 are Short

1

2

3

1

2

3

13

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Locations of the Jumpers and Connectors

Top View

JP7JP5

J5

CN1

CN2

SW1

J7

J2

JP2

J6

J1

JP1

JP4

JP3 JP6

J4

J3

SW2

J10

J11

CN6

CN16

VGA1

CN12CN10

CN5

USB1

LAN2

LAN1

JP10

CN3

JP14JP12

CN7

CN8

CN9

CN11

J12

J13

CN4

J9

J8

14

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

SW3

J14

Bottom View

15

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Jumpers and DIP Switch Settings

RTC and SRTC Clear Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: J12 (RTC) and J13 (SRTC)

Pin Settings

1-2 On Normal 2-3 On Clear

1-2 On: default

Pin Definition

1 NC 2 RTC Power 3 GND

1 3

AT/ATX Power Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP2

Pin Settings

1-2 On AT Mode 2-3 On ATX Mode

2-3 On: default

Pin Definition

1 AUTO (AT MODE) 2 PWRBT In 3 Manual ( ATX MODE)

1 3

16

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Dimming Signal Level Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP6

Pin Settings Model

1-2 On 3.3V OPPC 1940HT-J1900 2-3 On 5V OPPC 1540HT-J1900

1-2 On: default

Pin Definition

1 VCC3 2 Power for Dimming 3 VCC5

1 3

LCD Panel VDD Power Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP3

Pin Settings Model

1-2 On 3.3V OPPC 1540HT-J1900 2-3 On 5V OPPC 1940HT-J1900

1-2 On: default

Pin Definition

1 VCC3 2 Power for VDD 3 VCC5

1 3

17

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Touch 4/5 Wire Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP4

1 3

Pin Settings

1-2 On 5 wire 2-3 On 4 wire

1-2 On: default

COM1 RI Pin Power Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP12

1 3

Pin Settings

1-2 On RING 2-3 On +5V

1-2 On: default

Pin Definition

1 SP1_RI 2 SP1_PSRI 3 VCC5

18

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

COM2 RI Pin Power Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP14

1 3

Pin Settings

1-2 On RING 2-3 On +12V

1-2 On: default

Pin Definition

1 SP2_RI 2 SP2_PSRI 3 12V

1

O

N

234

Panel Resolution Select

Connector type: 4-pin DIP switch Connector location: SW2

Resolution SW2-1 SW2-2 SW2-3 SW2-4 Model

1024 x 768 ON OFF ON ON

OPPC 1540HT-

J1900

1280 x 1024 OFF ON ON OFF

OPPC 1940HT-

J1900

19

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

1

O

N

2

TYPE SW1-1 SW1-2

PWM Mode ON OFF

Analog Mode OFF ON

Dimming Type Select

Connector type: 2-pin DIP switch Connector location: SW1

20

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

External I/O Interfaces

Line-out Connector

Connector type: 1x 3.5mm TRS Connector location: CN3

Pin Definition Pin Definition

1 LOUT_R 2 JD 3 NC 4 LOUT_L 5 GND 6 GND

Pin Definition

1 PWRBT 2 GND

12

Remote Power On/Off Switch

Connector type: 2-pin switch Connector location: JP10

21

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

LAN1 Port

Support Wake on LAN (WOL)

Connector type: RJ45 port with LEDs Connector location: LAN1

ACT LINK

8 1

Act Status

Flashing Yellow Data activity

Off No activity

Link Status

Steady Green 1G network link

Steady Orange 100Mbps network link

Off 10Mbps or no link

Pin Definition Pin Definition

1 LAN1M0P 2 LAN1M0N 3 LAN1M1P 4 LAN1M2P 5 LAN1M2N 6 LAN1M1N 7 LAN1M3P 8 LAN1M3N

LAN2 Port

Connector type: RJ45 port with LEDs Connector location: LAN2

ACT LINK

8 1

Act Status

Flashing Yellow Data activity

Off No activity

Link Status

Steady Green 1G network link

Steady Orange 100Mbps network link

Off 10Mbps or no link

Pin Definition Pin Definition

1 LAN2M0P 2 LAN2M0N 3 LAN2M1P 4 LAN2M2P 5 LAN2M2N 6 LAN2M1N 7 LAN2M3P 8 LAN2M3N

22

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Dual USB 2.0 Port

Connector type: USB 2.0 ports, Type A Connector location: USB1

Single USB 3.0 Port

Connector type: USB 3.0 port, Type A Connector location: CN5

Pin Definition Pin Definition

1 VCC5 2 USB 2N 3 USB 2P 4 GND 5 VCC5 6 USB 1N 7 USB 1P 8 GND

Pin Definition Pin Definition

1 VCC5 2 USB 0N 3 USB 0P 4 GND 5 USB3_RX0_N 6 USB3_RX0_P 7 GND 8 USB3_TX0_N 9 USB3_TX0_P

1

5

4

8

4

5

1

9

23

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

COM1 Port

Connector type: DB-9 port, 9-pin D-Sub Connector location: CN10

COM2 Port

Connector type: DB-9 port, 9-pin D-Sub Connector location: CN12

1

6

5

9

1

6

5

9

Pin RS232 RS422 RS485

1 COM1_DCD COM1_TXD-

COM1_TXDCOM1_RXD-

2 COM1_RXD COM1_TXD+

COM1_TXD+

COM1_RXD+ 3 COM1_TXD COM1_RXD+ Reserve 4 COM1_DTR COM1_RXD- Reserve 5 COM1_GND COM1_GND Reserve 6 COM1_DSR COM1_RTS- Reserve 7 COM1_RTS COM1_RTS+: Reserve 8 COM1_CTS COM1_CTS+ Reserve

9

COM1_RI

(Could be a +5V

Power Pin)

COM1_CTS-

(Could be a +5V

Power Pin)

Reserve

(Could be a +5V

Power Pin)

Pin RS232 RS422 RS485

1 COM2_DCD COM2_TXD-

COM2_TXDCOM2_RXD-

2 COM2_RXD COM2_TXD+

COM2_TXD+

COM2_RXD+ 3 COM2_TXD COM2_RXD+ Reserve 4 COM2_DTR COM2_RXD- Reserve 5 COM2_GND COM2_GND Reserve 6 COM2_DSR COM2_RTS- Reserve 7 COM2_RTS COM2_RTS+ Reserve 8 COM2_CTS COM2_CTS+ Reserve

9

COM2_RI

(Could be a +12V

Power Pin)

COM2_CTS-

(Could be a +12V

Power Pin)

Reserve

(Could be a +12V

Power Pin)

24

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

VGA Port

Connector type: DB-15 port, 15-pin D-Sub Connector location: VGA1

Pin Definition Pin Definition

1 Red 2 Green 3 Blue 4 N/C 5 GND 6 GND 7 GND 8 GND

9 +5V 10 GND 11 N/C 12 DDC Data 13 HSYNC 14 VSYNC 15 DDC Clock

5

15 11

1

Pin Definition

1 DC+ 2 DC3 GND

+

G

31

12V - 30V DC Power Input

Connector type: Phoenix Contact 1x3 3-pin terminal block Connector location: CN16

25

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

S7 PC17PC1S1

CFast Card Slot

Connector type: Standard CFast connector Connector location: J14

Pin Definition Pin Definition

S1 GND S2 SATA_TXP2 S3 SATA_TXN2 S4 GND S5 SATA_RXN2 S6 SATA_RXP2 S7 GND PC1 CFAST_CDI

PC2 GND PC3 NC PC4 NC PC5 NC PC6 NC PC7 GND

PC8 CFAST_LED1_C PC9 CFAST_LED2_C PC10 NC PC11 NC PC12 NC PC13 VCC3 PC14 VCC3 PC15 GND PC16 GND PC17 CFAST_CDO

Pin Definition

1 Reset 2 Reset 3 GND 4 GND

Reset Button

Connector location: SW3

26

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Internal Connectors

CCFL Panel Backlight Connector

Connector type: 1x7 7-pin header JST, 2.5mm pitch Connector location: J4

Pin Definition Pin Definition

1 VCC5 2 12V 3 12V 4 BKCTRL 5 GND 6 GND 7 BKLEN

71

LVDS Channel A

Connector type: 2x10 20-pin header, 1.25mm pitch Connector location: CN2

Pin Definition Pin Definition

1 NC 2 NC 3 VDD 4 LVDS_DAT0P 5 LVDS_DAT3P 6 LVDS_DAT0N 7 LVDS_DAT3N 8 VDD

9 GND 10 LVDS_DAT1P 11 LVDS_CLK1P 12 LVDS_DAT1N 13 LVDS_CLK1N 14 GND 15 GND 16 +12V 17 LVDS_DAT2P 18 +12V 19 LVDS_DAT2N

11

9

22

0

27

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

LVDS Channel B

Connector type: 2x10 20-pin header, 1.25mm pitch Connector location: CN1

Pin Definition Pin Definition

1 NC 2 NC 3 VDD 4 LVDS_DAT4P 5 LVDS_DAT7P 6 LVDS_DAT4N 7 LVDS_DAT7N 8 VDD

9 GND 10 LVDS_DAT5P 11 LVDS_CLK2P 12 LVDS_DAT5N 13 LVDS_CLK2N 14 GND 15 GND 16 +12V 17 LVDS_DAT6P 18 +12V 19 LVDS_DAT6N

11

9

22

0

Line-in/Mic-in Connector

Connector type: 2x4 8-pin header, 2.54mm pitch Connector location: JP1

Pin Definition Pin Definition

1 LINE IN-LP 2 MIC1_L3 3 LINE IN-JD 4 MIC_JD 5 GND 6 GND 7 LINE IN-RP 8 MIC1_R3

17

28

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Speaker-out Connector

Connector type: 1x4 4-pin header, 2.54mm pitch Connector location: J6

Pin Definition

1 OUT-L+

2 OUT-L-

3 OUT-R+

4 OUT-R-

14

USB Connector

Connector type: 1x6 6-pin header JST, 2.5mm pitch Connector location: J7

61

Pin Definition Pin Definition

1 +5V 2 HUBUSB DM1 3 HUBUSB DP1 4 HUBUSB DM2 5 HUBUSB DP2 6 GND

29

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Touch Sensor Connector

Connector type: 1x5 5-pin header JST, 2.5mm pitch Connector location: J3

Pin 4-wire 5-wire

1 Bottom UR (H)

2 Right LR (X)

3 N/A Sense (S)

4 To p UL (Y)

5 Left LL (L)

SATA Connector

Connector type: Standard Serial ATA 7P (1.27mm, SATA-M-180) Connector location: CN8

1 7

Pin Definition Pin Definition

1 GND 2 TXP0 3 TXN0 4 GND 5 RXN0 6 RXP0 7 GND 8

15

30

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

SATA DOM Power Connector

Connector type: 1x2 2-pin header, JST 2.5mm pitch Connector location: J10

Pin Definition

1 +5V

2 GND

1

2

DIO Connector (Optional)

Connector type: 2x8 16-pin header, 2.54mm pitch Connector location: CN9

Pin Definition Pin Definition

1 DI1 2 DO1 3 DI2 4 DO2 5 DI3 6 DO3 7 DI4 8 DO4

9 NC 10 NC 11 COM1 12 NC 13 GND 14 GND 15 GND 16 GND

11

5

21

6

31

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Keyboard/Mouse Connector

Connector type: 2x4 8-pin header, 2.54mm pitch Connector location: JP7

Active LED Connector

Connector type: 1x6 6-pin header JST, 2.5mm pitch Connector location: J2

Pin Definition Pin Definition

1 VCC5 2 VCC5 3 KB_DATA 4 MS_DATA 5 KB_CLK 6 MS_CLK 7 GND 8 GND

Pin Definition Pin Definition

1 HDD_GND 2 HDD_PWR

3 PWR_GND 4 5VSB

5 VCC5

17

28

51

32

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Power Button

Connector type: 1x2 2-pin header JST, 2.0mm pitch Connector location: J1

Pin Definition

1 PWRBT 2 GND

1 2

Backlight Control Input Connector

Connector type: 1x4 4-pin header JST, 2.0mm pitch Connector location: J8

Pin Definition

1 GND

2 Tact Switch input

3 PIR IN

4 VCC3

14

33

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Dimming Control Input Connector

Connector type: 1x5 5-pin header JST, 2.0mm pitch Connector location: J5

1

5

Pin Definition Pin Definition

1 GND 2 Decreased input 3 Increased input 4 Light sensor input 5 VCC3

LVDS MCU FW Debug Connector

Connector type: 1x4 4-pin header, 2.54mm pitch Connector location: JP5

Pin Definition

1 VCC3

2 MCU_TCK

3 MCU_TDIO

4 GND

14

34

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Smart Fan Connector

Connector type: 1x4 4-pin Wafer, 2.54mm pitch Connector location: CN4

Pin Definition

1 GND 2 +12V 3 CPUFANIN 4 CPUFANOUT

14

Battery Connector

Connector type: 1x2 2-pin header JST, 1.25mm pitch Connector location: J11

Pin Definition

1 VBAT

2 GND

1 2

35

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Post Code Debug Connector

Connector type: 1x10 10-pin header, 1.0mm pitch Connector location: J9

Pin Definition Pin Definition

1 GND 2 PLTRST# 3 LPC_CLK 4 LPC_FRAME# 5 LPC_AD3 6 LPC_AD2 7 LPC_AD1 8 LPC_AD0 9 VCC3 10 VCC3

10 1

SIM Card Slot

Connector location: CN6

C5 C6 C7

C1 C2 C3

Pin Definition Pin Definition

C1 UIM_PWR C2 UIM_RST C3 UIM_CLK C5 GND C6 UIM_VCCP C7 UIM_DAT

36

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Mini-PCIe Slot

Connector location: CN11

12

51 52

Pin Definition Pin Definition

1 WAKE0# 2 +V3.3_MINI 3 NC 4 GND 5 NC 6 +V1.5S_MINI 7 NC 8 NC

9 GND 10 NC 11 GPP_CLK1_N 12 NC 13 GPP_CLK1_P 14 NC 15 GND 16 NC 17 NC 18 GND 19 NC 20 MINICARD1_DIS# 21 GND 22 PCIE_RST# 23 PCIE_RX2N 24 +V3.3A_MINI 25 PCIE_RX2P 26 GND

Pin Definition Pin Definition

27 GND 28 +V1.5S_MINI 29 GND 30 SMB_CLK 31 PCIE_TX3N 32 SMB_DAT 33 PCIE_TX3P 34 GND 35 GND 36 USB_1N 37 GND 38 USB_1P 39 +V3.3A_MINI 40 GND 41 +V3.3A_MINI 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +V1.5S_MINI 49 NC 50 GND 51 NC 52 +V3.3A_MINI

37

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Mini-PCIe Slot (Wi-Fi/3G)

Connector location: CN7

12

51 52

Pin Definition Pin Definition

1 PCIEWAKE 2 3.3V

3 NC 4 GND

5 NC 6 1.5V

7 CLKREQ 8 UIM_PWR

9 GND 10 UIM_DAT 11 PCIECLKN 12 UIM_CLK 13 PCIECLKP 14 UIM_RST 15 GND 16 UIM_VCCP 17 NC 18 GND 19 NC 20 DISABLE 21 GND 22 PLTRSTBF 23 PCIERX4N 24 3.3V 25 PCIERX24P 26 GND

Pin Definition Pin Definition

27 GND 28 1.5V 29 GND 30 SMBCLK 31 PCIETX4N 32 SMBDATA 33 PCIETX4P 34 GND 35 GND 36 USB2N 37 GND 38 USB2P 39 3.3V 40 GND 41 3.3V 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 1.5V 49 NC 50 GND 51 NC 52 3.3V

38

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 2: Jumpers and Connectors

Block Diagram

PCIe x1

LAN i210

VGA

DDR3L SO-DIMM

Thermal Sensor *2 Voltages *4

80 port

Giga LAN

SPI 2MB

RJ45

Giga LAN

RJ45

DDR3L 1066

LPC Bus

HDA_SDI0

PCIe x1

1 Slot

PCI-E *1(4)

SPI

USB 2.0 (4)

Bay Trail-I

Dual Core CPU

E3826

DDR3L-1066

1-2 - Rear

ITE8786

Super I/O

SATA (2)

USB 2.0X3

DDI PORT1DDI PORT0

DDR3L CH2

LPCLCIHDA

SATA Gen2

PCIe x1

LAN i210

Audio Codec ALC886

MIC-IN

PS2 KB/MS

DDR3L CH1

3G(USB)

2 - MiniPCIE Connector

USB 3.0 (1)

Controller

3- Penmount Touch

USB 3.0

USB 2.0X1

0 - Rear

1- Internal/mini-PCIe

Connector

7W

3.25X27mm

DDR3L SO-DIMM

@ Maximum resolution:1900 * 1200

@ Maximum 8GBytes

2 Slot

CH7511

DP to LVDS

COM1

WOL Support

@ Maximum resolution:1920 * 1080

LVDS 48bit Support

COM3

RS-232/422/485

COM2

RS-232

RS-232/422/485

RS-232C OM4

ISOLATION

Line-in

DIO BOX Header

SATA0 HDD

(DOM Support)

GENESYS GL850

3- USB HUB 1~ 4

down stream

0 - Internal connector

GPIO2IN/2OUT

AMP TPS6047A4RHBR

HEAD PHONE

SPEAKER

Display Port

PCIe x1

3G

Mini-PCIe

Wi-Fi

SATA1 CFAST

SATA Gen2

VGA

Co-layout with BOX HEADER

VGA DB15Pin (Slim type)

39

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

ChaPter 3: system setuP

Installing a SATA Hard Drive

1. Remove the mounting screws around the chassis cover and then remove the cover.

CAUTION!

CAUTION!CAUTION!

Prior to removing the chassis cover, make sure the unit’s power is off and disconnected from the power sources to prevent electric shock or system damage.

The dots denote the locations of the screws.

40

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

2. Remove the mounting screws of the drive bay. 3. Remove the drive bay. The drive bay is used to hold a SATA hard drive.

Mounting

screw

41

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

4. Place the SATA hard drive on the drive bay.

SATA drive

Drive bay

5. Align the mounting holes that are on the sides of the SATA drive with the mounting holes on the drive bay and then use the provided mounting screws to secure the drive in place.

Mounting screw

42

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

6. Place the SATA drive in the chassis and then use the provided mounting screws to secure the drive in the chassis.

Connect the SATA data cable and SATA power cable to the connectors

on the SATA drive.

SATA drive

SATA data

cable

SATA power cable

43

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Installing a CFast Card

1. The CFast card socket is located on the rear top side of the chassis.

CFast card socket

2. Remove the mounting screws of the CompactFlash socket’s cover.

Mounting screw

44

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

3. With the CFast card’s label facing up, insert the card until it is completely seated in the socket.

CFast card

4. Push the CFast card to remove it.

Push CFast card

Ejected

CFast card

45

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Installing a SO-DIMM Memory Module

1. With the chassis cover removed, insert the module into the SO-DIMM socket at an approximately 30 degrees angle. Apply firm even pressure to each end of the module until it slips into the socket. The gold-plated connector on the edge of the module will almost completely disappear inside the socket.

2. Push the module down until the clips on both sides of the socket lock into position. You will hear a distinctive “click” sound, indicating the module is correctly locked into position.

46

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Installing a SATA DOM

1. Remove the drive bay bracket and cable. The SATA connector is readily accessible upon removing the bracket.

SATA connector

2. Remove the screw.

47

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

3. The SATA DOM package includes a SATA DOM, supporting stud and cable.

4. Install the supporting stud. Make sure the stud is fastened in place.

Supporting

stud

Cable

SATA DOM

48

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

5. Connect one end of the provided cable to the connector on the module.

Connect to the

module

6. Install the module to the SATA port via the connector at the solder side of the module and then secure the module using the mounting screw you removed in step 2. Connect one end of the provided cable to the connector on the board.

Mounting screw

49

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

7. Connect the other end of the cable to the connector on the board.

50

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Installing a Mini PCIe Module

1. The Mini PCIe module package includes the following items.

Mini PCIe Module

Antennas

RF Cables

Mini PCIe slot

2. Insert the Mini PCIe module into the Mini PCIe slot at a 45 degrees angle until the gold-plated connector on the edge of the module completely disappears inside the slot.

Mini PCIe module

51

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

3. Secure the module with mounting screws.

Mounting screw

4. Attach one end of the RF cables onto the module.

RF cable

52

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

5. Push the antenna hole cover.

6. Remove the antenna hole covers.

7. Insert the antenna jack end of the cable through the antenna hole.

53

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

8. Insert the ring onto the antenna jack end of the cable.

Ring

Antenna jack

Antenna jack Ring

9. Connect external antennas to the antenna jacks.

54

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Installing the Front Bezel on OPPC 1540HT-J1900 (Optional)

1. The optional front bezel kit includes a front bezel, brackets, and mounting screws.

Front view of the bezel

2. The photo below shows the rear view of the bezel and the corresponding brackets and mounting screws needed to mount the bezel.

Rear view of the bezel

Bezel

Mounting screws

Brackets

Note: The installation instructions are the same as those for OPPC 1520T. Images are based on OPPC 1520T.

55

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

3. Mount the brackets to their corresponding mounting holes located on the sides of the Panel PC.

Brackets and their corresponding

mounting screws

Mounting holes

Bracket

4. The photo below shows the 4 brackets mounted in place.

Bracket

56

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

5. Attach the front bezel onto the Panel PC.

Front bezel

Rear view

6. Viewing from the rear side of the bezel, the red dots denote the locations of the mounting screws.

57

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

8. The photo below shows the front bezel already secured in place.7. With the rear side of the Panel PC facing up, secure the front bezel

with the provided mounting screws.

58

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Installing the Front Bezel on OPPC 1940HT-J1900 (Optional)

1. The optional front bezel kit includes a front bezel and mounting screws.

Front view of the bezel

2. The photo below shows the rear view of the bezel and the corresponding brackets and mounting screws needed to mount the bezel.

Rear view of the bezel

Bezel

Mounting screws

Note: The installation instructions are the same as those for OPPC 1720T. Images are based on OPPC 1720T.

59

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

3. Attach the front bezel onto the Panel PC.

Front bezel

Rear view

4. Viewing from the rear side of the bezel, the red dots denote the locations of the mounting screws.

60

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

6. The photo below shows the front bezel already secured in place.5. With the rear side of the Panel PC facing up, secure the front bezel

with the provided mounting screws.

61

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Plugging the DC Power Cable

1. Plug the DC 4-pin DIN power jack (male) into the DC 4-pin DIN power jack (female) that is on the system.

2. The table below shows the pin definition of the cable.

Color Pin Definition

Black GND

Red&Yellow DC+

Blue&Black DC-

62

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Panel Mounting

1. Select a place on the panel where you will mount the Panel PC.

2. Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions.

The thickness of the panel (e.g. steel board, plank, acrylic board, wall,

etc.) where you will mount the Panel PC must not exceed 7mm. If the distance between the front bezel and panel mount hole is too wide, it will not fit the panel mount kit.

334 ±0.5

261 ±0.5

7mm max.

CUT OUT SIZE T=7mm(MAX)

OPPC 1540HT-J1900

3. Slide the Panel PC through the hole until it is properly fitted against the panel.

OPPC 1940HT-J1900

403 ±0.5

331 ±0.5

7mm max.

CUT OUT SIZE T=7mm(MAX)

63

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

2. Position the mounting clamps along the rear edges of the Panel PC. The first and second clamps must be positioned and secured diagonally prior to mounting the rest of the clamps. Tighten the clamp’s screw until it touches the panel. Do not overtighten the screws to prevent damaging the Panel PC.

Panel Mount Kit (Optional)

1. The optional mounting clamps must be attached along the rear edges of the Panel PC.

Clamp

Panel

OPPC 1940HT-J1900

OPPC 1540HT-J1900

64

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

4. The photo below shows the front view of the Panel PC mounted on the panel.

3. The photo below shows the mounting clamps mounted in place.

Panel

Panel PC

OPPC 1940HT-J1900

OPPC 1540HT-J1900

OPPC 1940HT-J1900

OPPC 1540HT-J1900

Panel

Panel PC

65

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Front Bezel Design Guide

The illustration below shows the dimensions of the panel. It serves as a guide for you to design the front bezel.

OPPC 1540HT-J1900

316.500

306.500

230.500

240.500

378.32

376.32

301.06

303.06

3M for IP65 test tape size 316.5 x 5mm T=1.0

Active area cut out size

3M for IP65 test tape size 240.5 x 5mm T=1.0

3M for IP65 test tape size 350 x 5mm T=1.0

Active area cut out size

OPPC 1940HT-J1900

3M for IP65 test tape size 282.5 x 5mm T=1.0

66

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 3: System Setup

Open Frame Mount

Front Mount (Outer Side Mount)

334

261

OPPC 1540HT-J1900

366

304.2

OPPC 1940HT-J1900

The cut out size of the Outer Side Mount is the same as the cut out size of the Panel Mount.

67

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

ChaPter 4: BIos setuP

This chapter describes how to use the BIOS setup program for the OPPC 1540HT-J1900/1940HT-J1900 series. The BIOS screens provided in this chapter are for reference only and may change if the BIOS is updated in the future.

To check for the latest updates and revisions, visit the NEXCOM website at www.nexcom.com.tw.

About BIOS Setup

The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs. It is a ROM-based configuration utility that displays the system’s configuration status and provides you with a tool to set system parameters.

These parameters are stored in non-volatile battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS.

With easy-to-use pull down menus, you can configure such items as:

▪ Hard drives, diskette drives, and peripherals

▪ Video display type and display options

▪ Password protection from unauthorized use

▪ Power management features

The settings made in the setup program affect how the computer performs. It is important, therefore, first to try to understand all the setup options, and second, to make settings appropriate for the way you use the computer.

When to Configure the BIOS

▪ This program should be executed under the following conditions:

▪ When changing the system configuration

▪ When a configuration error is detected by the system and you are

prompted to make changes to the setup program

▪ When resetting the system clock

▪ When redefining the communication ports to prevent any conflicts

▪ When making changes to the Power Management configuration

▪ When changing the password or making other changes to the security

setup

Normally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the CMOS RAM has lost power, or the system features need to be changed.

68

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Default Configuration

Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering Setup

When the system is powered on, the BIOS will enter the Power-On Self Test (POST) routines. These routines perform various diagnostic checks; if an error is encountered, the error will be reported in one of two different ways:

▪ If the error occurs before the display device is initialized, a series of beeps

will be transmitted.

▪ If the error occurs after the display device is initialized, the screen will

display the error message.

Powering on the computer and immediately pressing <Del> allows you to enter Setup.

Press the

key to enter Setup:

Legends

Key Function

Moves the highlight left or right to select a menu.

Moves the highlight up or down between sub-menus or fields.

Exits the BIOS Setup Utility.

Scrolls forward through the values or options of the highlighted field.

Scrolls backward through the values or options of the highlighted field.

Selects a field.

Displays General Help.

Load previous values.

Load optimized default values.

Saves and exits the Setup program.

Press <Enter> to enter the highlighted sub-menu

69

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Scroll Bar

When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

Submenu

When “” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press .

70

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

BIOS Setup Utility

Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on the screen. The main menu allows you to select from several setup functions and one exit. Use arrow keys to select among the items and press to accept or enter the submenu.

Main

The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.

Save & ExitAdvanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set the Date. Use Tab to switch between Date elements.

BIOS Information BIOS Vendor Core Version Compliancy Project Version Build Date and Time

CPU Conguration

Microcode Patch

Memory Information Total Memory

System Date

System Time

American Megatrends

5.009 UEFI 2.3; PI 1.2 A200A007 x64 10/24/2014 12:00:26

901

2048 MB

[Tue 07/09/2019] [12:01:07]

System Date

The date format is <day>, <month>, <date>, <year>. Day displays a day, from Monday to Sunday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1999 to 2099.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.

71

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Advanced

The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Setting incorrect field values may cause the system to malfunction.

Exit

Advanced Chipset PCIPnP Security

Main

Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not effective with some OS.

ACPI Settings

Enable Hibernation

ACPI Sleep State

Enable Hibernation

Disabled

[Enabled]

[S3 (Suspend to RAM)]

ACPI Settings

This section is used to configure ACPI Settings.

Enable Hibernation

Enables or disables system ability to hibernate (OS/S4 Sleep State). This option may not be effective with some OS.

Enabled

Save & ExitAdvanced Chipset Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

System ACPI Parameters.

ACPI Settings

IT8786E Super IO Conguration

Hardware Monitor

CPU Conguration PPM Conguration IDE Conguration USB Conguration

►

► ► ► ► ► ►

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

72

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Exit

Advanced Chipset PCIPnP Security

Main

Select the ACPI sleep state the system will enter when the SUSPEND button is pressed.

ACPI Settings

Enable Hibernation

ACPI Sleep State

[Enabled]

[S3 (Suspend to RAM)]

Select the highest ACPI sleep state the system will enter when the suspend button is pressed. The options are Suspend Disabled and S3 (Suspend to RAM).

ACPI Sleep State

S3 (Suspend to RAM)

ACPI Sleep State

Suspend Disabled

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

IT8786E Super IO Configuration

This section is used to configure the serial ports.

Super IO Chip

Displays the Super I/O chip used on the board.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set Parameters of Serial Port 1 (COMA)

IT8786E Super IO Conguration

Super IO Chip

Serial Port 1 Conguration

Serial Port 2 Conguration

IT8786E



73

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Serial Port 1 Configuration

This section is used to configure serial port 1.

Serial Port

Enables or disables the serial port.

Onboard Serial Port Mode

Select this to change the serial port mode to RS232, RS422, RS485 or RS485 Auto.

Terminal Resistor

Enables or disables the terminal resistor.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 1 Conguration

Serial Port

Device Settings

Onboard Serial Port Mode Terminal resistor

[Enabled]

IO=248h; IRQ=5;

[RS232] [Enabled]

Serial Port 2 Configuration

This section is used to configure serial port 2.

Serial Port

Enables or disables the serial port.

Onboard Serial Port Mode

Select this to change the serial port mode to RS232, RS422, RS485 or RS485 Auto.

Terminal Resistor

Enables or disables the terminal resistor.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 2 Conguration

Serial Port

Device Settings

Onboard Serial Port Mode Terminal resistor

[Enabled]

IO=2F8h; IRQ=3;

[RS232] [Enabled]

74

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Hardware Monitor

This section is used to monitor hardware status such as temperature, fan speed and voltages.

CPU Temperature

Detects and displays the current CPU temperature.

System Temperature

Detects and displays the current system temperature.

SYS Fan Speed

Detects and displays the system fan speed.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Pc Health Status

CPU temperature System temperature SYS Fan Speed VCore VCC12 VCC5 VCC3

: +36 C : +36 C : N/A : +0.828 V : +11.952 V : +5.040 V : +3.330 V

VCore

Detects and displays the Vcore CPU voltage.

VCC12

Detects and displays 12V voltage.

VCC5

Detects and displays 5V voltage.

VCC3

Detects and displays 3.3V voltage.

75

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

CPU Configuration

This section is used to configure the CPU.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Socket specic CPU Information

CPU Conguration

Socket 0 CPU Information

CPU Speed 64-bit

Active Processor Cores Limit CPUID Maximum Execute Disable Bit Intel Virtualization Technology

1460 MHz Supported

[All] [Disabled] [Enabled] [Enabled]



Active Processors Cores

Select the number of cores to enable in each processor package.

Limit CPUID Maximum

The CPUID instruction of some newer CPUs will return a value greater than 3. The default is Disabled because this problem does not exist in the Windows series operating systems. If you are using an operating system other than Windows, this problem may occur. To avoid this problem, enable this field to limit the return value to 3 or lesser than 3.

Execute Disable Bit

When this field is set to Disabled, it will force the XD feature flag to always return to 0. XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1,Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3).

Intel® Virtualization Technology

Enables or disables Intel Virtualization technology.

76

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Socket 0 CPU Information

Display information on the CPU installed on socket 0.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Socket 0 CPU Information

Intel(R) Atom(TM) CPU E3826 @ 1.46GHz CPU Signature Microcode Patch Max CPU Speed Min CPU Speed Processor Cores Intel HT Technology Intel VT-x Technology

L1 Data Cache L1 Code Cache L2 Cache L3 Cache

30679 901 1460 MHz 533 MHz 2 Not Supported Supported

24 kB x 2 32 kB x 2 512 kB x 1 Not Present

PPM Configuration

This section is used to configure the Processor Power Management (PPM) configuration.

EIST

Enables or disables Intel® SpeedStep.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable/Disable Intel SpeedStep

PPM Conguration

EIST

[Disabled]

77

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

IDE Configuration

This section is used to configure the SATA drives.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable / Disable Serial ATA

IDE Conguration

Serial-ATA (SATA)

SATA Speed Support SATA Mode

Serial-ATA Port 0 SATA Port0 HotPlug

Serial-ATA Port 1 SATA Port1 HotPlug

SATA Port0 TOSHIBA MQ01AB (320.0GB)

SATA Port1 Not Present

[Enabled]

[Gen2] [IDE Mode]

[Enabled] [Disabled]

Serial-ATA (SATA)

Enables or disables the SATA controller.

SATA Speed Support

Configures the SATA controller as Gen1 or Gen2.

SATA Mode

Configures the SATA as IDE or AHCI mode.

IDE This option configures the Serial ATA drives as Parallel ATA physical storage device.

AHCI This option configures the Serial ATA drives to use AHCI (Advanced Host Controller Interface). AHCI allows the storage driver to enable the advanced Serial ATA features which will increase storage performance.

Serial-ATA Port 0

Enables or disables SATA port 0.

SATA Port0 HotPlug

Enables or disables hot pluggable support on SATA port 0.

Serial-ATA Port 1

Enables or disables SATA port 1.

SATA Port1 HotPlug

Enables or disables hot pluggable support on SATA port 1.

78

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

USB Conguration

USB Module Version

USB Devices: 2 Keyboards, 1 Point, 2 Hubs

Legacy USB Support

USB3.0 Support XHCI Hand-off EHCI Hand-off

8.10.27

[Enabled]

[Enabled] [Enabled] [Disabled]

Legacy USB Support

Enable Enables Legacy USB. Auto Disables support for Legacy when no USB devices are connected. Disable Keeps USB devices available only for EFI applications.

USB3.0 Support

Enables or disables USB 3.0 controller support.

XHCI Hand-off and EHCI Hand-off

This is a workaround for OSs that does not support XHCI hand-off and EHCI Hand-off. The XHCI and EHCI ownership change should be claimed by the XHCI and EHCI driver respectively.

USB Configuration

This section is used to configure the USB.

Troubleshooting: When installing Windows 7 from USB, USB

3.0 will not be supported. Please disable XHCI and enable EHCI to allow USB installation of Windows 7.

79

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Chipset

This section gives you functions to configure the system based on the specific features of the chipset. The chipset manages bus speeds and access to system memory resources.

Save & Exit

Advanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Pyroelectric sensor or Tact Switch

Backlight Control Select From

Backlight On/Off Reverse Backlight Dimming Reverse Backlight Dimming Control By Backlight Dimming Select

South Bridge

[Tact Switch]

[Normal] [Normal] [Manual] [100%]

Backlight Control Select From

The available options are Pyroelectric sensor and Tact Switch.

Backlight On/Off Reverse

Enables or disables reverse backlight On/Off. Please configure this option only when changing the panel, otherwise the display may not work.

►

Backlight Dimming Reverse

The available options are PWM & Analog Dimming Reverse and Normal.

Backlight Dimming Control By

The available options are Tact Switch, Manual and Light sensor.

Backlight Dimming Select

Adjusts the brightness of the backlight.

South Bridge

Enters the South Bridge submenu.

80

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

South Bridge

High Precision Timer

Enables or disables high precision event timer.

Restore AC Power Loss

Select the AC power state when power is re-applied after a power failure.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Azalia HD Audio Options

Azalia HD Audio

USB Conguration PCI Express Conguration

High Precision Timer Restore AC Power Loss

[Enabled] [Power On]

►

► ►

PCH Azalia Configuration

Azalia

Control detection of the Azalia device.

Disabled Azalia will be unconditionally Disabled. Enabled Azalia will be unconditionally Enabled.

Azalia HDMI Codec

Enables or disables internal HDMI codec for Azalia.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled Enabled = Azalia will be unconditionally Enabled Auto = Azalia will be enabled if present disabled otherwise.

Audio Conguration

Audio Controller

Azalia HDMI Codec

[Enabled]

81

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

USB Configuration

USB 2.0(EHCI) Support

Enables or disables the Enhanced Host Controller Interface (USB 2.0), one EHCI controller must always be enabled.

USB RMH Mode

Enables or disables PCH USB rate matching hubs mode.

USB EHCI Debug

Enables or disables PCH EHCI debug capability.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Control the USB EHCI (USB 2.0) functions. One EHCI controller must always be enabled

USB Conguration

XHCI Mode

USB 2.0(EHCI) Support

USB RMH Mode USB EHCI debug

[Disabled]

[Enabled]

[Enabled] [Disabled]

PCI Express Configuration

PCI Express Port 0 to PCI Express Port 3

Enables or disables the PCI Express ports 0 to 3 on the chipset.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable the PCI Express Port 0 in the Chipset.

PCI Express Conguration

PCI Express Port 0

PCI Express Port 1

PCI Express Port 2

PCI Express Port 3

[Enabled]

82

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Security

Save & ExitAdvanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set Administrator Password

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User Will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20

Administrator Password

User Password

Administrator Password

Select this to reconfigure the administrator’s password.

User Password

Select this to reconfigure the user’s password.

Boot

This section is used to configure the boot features.

Bootup NumLock State

This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys.

Fast Boot

When enabled, the BIOS will shorten or skip some check items during POST. This will decrease the time needed to boot the system.

Save & Exit

Advanced Chipset

Security

BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Select the keyboard NumLock state

Boot Conguration

Bootup NumLock State

Fast Boot

Network Onboard LAN PXE

Boot Option Priorities

Boot Option #1 Boot Option #2

Hard Drive BBS Priorities

[On]

[Disabled]

[Enabled] [Disabled]

[SATA PM: TOSHIBA M. . .] [UEFI: Built-in EFI . . .]

83

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Hard Drive BBS Priorities

Sets the order of the legacy devices in this group.

Save & Exit

Advanced

Chipset

Boot

BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Sets the system boot order

Boot Option #1

[SATA PM: TOSHIBA M . . .]

Network

Controls the execution of UEFI and legacy PXE OpROM.

Onboard LAN PXE

Options to disable onboard LAN PXE ROM or enable it for LAN1 or LAN2 .

Boot Option Priorities

Adjust the boot sequence of the system. Boot Option #1 is the first boot device that the system will boot from, next will be #2 and so forth.

84

OPPC 1540HT-J1900/1940HT-J1900 User Manual

Chapter 4: BIOS Setup

Save & Exit

Save Changes and Reset

To save the changes and reset, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Discard Changes and Reset

To exit the Setup utility without saving the changes, select this field then press <Enter>. You may be prompted to confirm again before exiting.

Restore Defaults

To restore the BIOS to default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Save & ExitAdvanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Reset the system after saving the changes.

Save Changes and Reset

Discard Changes and Reset Restore Defaults

Nexcom OPPC 1540HT-J1900, OPPC 1940HT-J1900 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual