NEW HOLLAND PLM
Precision Land Management
Experts in our Field – Precision in Yours
2 3
NEW HOLLAND PLM –
AN INTRODUCTION TO GPS
WHAT IS GPS?
The GPS (Global Positioning System) operated by the U.S department of Defence and GLONASS operated by the
Russian Federation are a space-based navigation system formed from a network of satellites which determine the
position of a vehicle using signals from the 32 satellites that circle the earth. These satellites travel in known orbits that
allow a land based receiver to determine its own position in relation to each satellite from which it receives a signal.
The GPS antenna fitted to the machine receives continuous signals from the GPS satellites. Ground based GPS
receivers, at known locations across the country, receive the same signals. As their absolute location is known, they can
calculate the real time position and send a position correction signal. Geostationary satellites then return the correction
signal to the GPS receiver on the vehicle, and the correction can be applied to the received position.
The signals generated by GPS alone are not accurate enough for use in agriculture. Therefore, corrections must be
made to GPS signals to improve their accuracy. With these correction signals we refer to the system as DGPS
(Differential Global Positioning System).
There are two main DGPS correction services available today:
SBAS
The GPS (Global Positioning System)
operated by the U.S department of
Defence and GLONASS operated by
the SBAS-Satellite Based Augmentation
System,communicate difference via
geostationary satellite.
RTK
Real Time Kinematics, communicate
difference directly to the vehicle via
short wave radio from a local base
station.
MAXIMISE YIELDS, CONTROL INPUT
COSTS + OPTIMISE PROFITS
WHY GPS GUIDANCE? BENEFITS OF VEHICLE GUIDANCE
GIVE YOUR BUSINESS A COMPLETE AND FLEXIBLE GPS SOLUTION
From the enhanced productivity of lightbar guidance, to the pinpoint accuracy of fully integrated guidance, and the
valuable analysis of yield data, our Precision Land Management offering will help maximise yields, control input costs
and optimise profits.
REDUCE OPERATIONAL COSTS
The primary purpose of New Holland’s Precision Land
Management is to save fuel and input costs by ensuring parallel
passes when working either in straight lines, curves, pivots or on
undulating ground minimising skips and overlaps.
IMPROVE PRODUCTIVITY, EVEN IN DUSTY CONDITIONS
When planting, spraying, cultivating or harvesting in difficult
weather conditions or at night, the operator can focus on his task
without any risk of overlap or joining rows while driving faster.
HOW ACCURATE IS GPS?
An uncorrected GPS or GLONASS signal gives you position accuracy between 5 to 10 meters. This is more than
adequate for car navigation systems, but not accurate enough for vehicle guidance in agricultural applications, where
we need Pass-to-Pass and Year-to-Year accuracy and repeatability.
Pass-to-Pass accuracy measures the relative accuracy over a 15 minute interval. This is usually thought of as skip/
overlap from one pass to the next when driving swaths. A New Holland receiver with pass-to-pass accuracy of
+/-2.5 cm means you get less than +/-2.5 cm skip or overlap, 95% of the time.
Year-to-Year accuracy is the measure of repeatable accuracy which means that you can drive the same rows a day,
week, month, or year later. So, +/- 2.5 cm year-to-year accuracy means you can drive the same rows next year within
+/- 2.5 cm of this year’s rows, 95% of the time.
INCREASE OPERATOR’S COMFORT
Operators using guidance solutions often report “being less
fatigued and stressed” as one of the fundamental advantages of
precision farming, leading to increased work rates and
efficiency.
CONTROLLED TRAFFIC FARMING PRACTICES
With RTK enabled New Holland guidance systems the practice
of Controlled Traffic Farming can be adopted, leading to a
significant reduction in field compaction improving overall yields.
CHOOSE A SIMPLE AND VERSATILE SOLUTION
For your new purchases of New Holland Machines, we offer factory installed fully integrated guidance solutions.
For all makes and models of equipment of your existing fleet, we provide a full range of leading aftermarket solutions for
GPS-based guidance, from entry-level to high end.
Regardless of your farm operation, the brands of your machines and your budget, this precision farming brochure will
help you determine which system is right for you.
4 5
NEW HOLLAND PLM –
THE COMPLETE, FLEXIBLE GPS SYSTEM
FOUR LEVELS OF ACCURACY
1. AUTONOMOUS WITH ONPATH FILTER
For Autonomous systems only, utilising mathematical filters to
increase the system accuracy. The OnPath filter provides +/-3045cm pass to pass accuracy without the use of a correction
signal.
2. OMNISTAR VBS (SINGLE FREqUENCY CORRECTION)
The vehicle with a DGPS antenna receives signals from the GPS
satellite constellation.
The OmniSTAR® services, which have a number of ground based
GPS receivers spread across the area for which they deliver a
correction, receive the same GPS messages as the vehicle. They
are able to calculate the real time position error and send this as
a message to control stations, which then upload the message to
a geostationary satellite. The geostationary satellite receives the
correction message, and re-transmits it as a single frequency
signal back to the receiver on the vehicle.
3. DIFFERENTIAL GPS WITH OMNISTAR®
(DUAL FREqUENCY CORRECTION)
Process as per OmniSTAR VBS.
On this higher accuracy system, the geostationary satellite,
transmits the correction message as a dual frequency signal back
to the receiver on the vehicle.
4. RTK (REAL TIME KINEMATIC)
This is a highly precise technology that results in +/-2.5 cm
year-to-year accuracy.
This accuracy can be achieved with two communication
technologies, depending upon your needs in terms of working
area coverage:
RTK (RADIO TRANSMISSION)
RTK uses a local ground based station which receives the same position data as the mobile unit. By comparing the
received position to its known actual position, the real time error can be calculated. This error is then transmitted via
short wave radio to the mobile unit.
Radio repeaters can be positioned to fill in any areas of signal loss from the base station. Signal loss could be caused
by rugged terrain or thick vegetation.
Accuracy level Pass to Pass Year to Year
OnPath +/-30cm +/-90cm
OmniSTAR® VBS* +/-20cm +/-60cm
OmniSTAR® XP* +/-7cm +/-12cm
OmniSTAR® HP* +/-5cm +/-10cm
RTK +/-2.5cm +/-2.5cm
*Information from OmniSTAR®
HOW TO CHOOSE YOUR
GUIDANCE SOLUTION
RTK
+/-2.5 cm
OnPath OmniSTAR® XP OmniSTAR® HP pass-to-pass
+/-30 cm +/-7 cm +/-5 cm and year-to-year
Application pass-to-pass pass-to-pass pass-to-pass repeatable
Spraying 3 3 3 3
Spreading 3 3 3 3
Tillage 3 3 3 3
Mapping 3 3 3 3
Mowing 3 3 3
Harvesting 3 3 3
Seeding 3 3 3
Bed Forming 3
Planting 3
Strip Till 3
Display
EZ-Guide® 250 3
FM-750 3 3 3 3
FM-1000™ 3 3 3 3
Intelliview™ III 3 3 3 3
Guidance Type
Manual – Lightbar 3
Assisted – EZ-Steer® 3 3 3
Integrated – Autopilot™ 3 3 3
Integrated – IntelliSteer™ 3 3 3
6 7
MANUAL GUIDANCE ASSISTED GUIDANCE
ASSISTED GUIDANCE – EZ-STEER™
Enhance your guidance package by upgrading to the EZ-Steer® assisted steering system, which delivers an excellent
hands free solution.
MANUAL GUIDANCE WITH LIGHTBAR
The entry level guidance solution allows you to explore GPS guidance through a simple and affordable lightbar display.
A lightbar based guidance system provides you with quick on-line visual feed back to keep you on your intended path.
The lightbar assists you with the direction and how much manual steering is required. A manual guidance system
provides a less expensive option, ideal for most applications and minimises the investment required.
EZ-GUIDE 250
The EZ-Guide® 250 is a simple and affordable, user friendly tool offering you an accuracy of +/-20 cm pass-to-pass.
The built in OnPath® filter technology provides improved pass-to-pass accuracy. The EZ-GUIDE 250 is compatible with
all makes and models.
FREEFORM™ GUIDANCE
PATTERN
11 CM COLOUR SCREEN
Choose between plan and 3D
perspective views, to see at a
glance where you are and
what you’ve been doing.
Offers the ultimate in guidance
flexibility, allowing you to work in
different patterns and shapes that
best fit your field’s layout and
contours.
EZ-Steer® is the world’s simplest portable hands-free farming system for all vehicle models, old and new.
The EZ-Steer® system turns the steering wheel for you by combining a friction wheel and a motor thanks to a DGPS
guidance signal from the EZ-Guide® 250, FM-750™ or FM-1000™ displays.
While the EZ-Steer® keeps you on line on undulating land, ditches, waterways and terraces, you can focus on many
different tasks, such as sprayer or planter performance, improving job quality and crop yields while reducing stress.
EZ-STEER® MOTOR
The EZ-Steer® motor receives electrical signals from the
EZ-Steer® controller and converts them to precise
commands that the vehicle’s steering system uses to keep
the vehicle on track.
You can resume the control of your machine at anytime by
turning the steering wheel.
EZ-STEER® CONTROLLER
Using data from the GPS receiver, the EZ-Steer® controller
sends precise instructions to the steering wheel motor. T2™
technology continually corrects for roll and yaw by using
4-axis solid state inertial sensors to give you a true
on-ground position.
NIGHT OR DAY USE
Switch to Night Mode for
better visibility. Mark and
locate in-field hazards with
feature mapping.
Find easily the next path
with SwathFinder
assistance.
FIELDFINDER TECHNOLOGY
Automatically locate stored fields
as you drive near them.
15 BRIGHT
GUIDANCE LEDS
Give you quick
on-line visual
feedback to keep
you on track
USB FLASH DRIVE
Simply transfer your day’s
coverage maps to your computer
using a USB flash drive and easily
print out coverage reports import/
export fields and coverage
maps via USB.
Position without
terrain compensation
COMPATIBLE DISPLAYS
EZ-GUIDE 250
FM-750
FM-1000
GPS receiver
Position corrected
TM
by T2 technology
Roll angle
T2™ TERRAIN COMPENSATION TECHNOLOGY
Terrain compensation technology calculates the difference
between the DGPS antenna’s location and the desired
“working position” of the vehicle’s centre point on the
ground. No matter what angle the vehicle may be tilting, it
improves accuracy when driving on flat ground with rough
terrain and accuracy on slopes, hills and when driving over
terraces, ditches and waterways.
8 9
ASSISTED GUIDANCE – DISPLAYS
FM-750
The cornerstone of guidance, capable of 2.5 cm accuracy. The FM-750 has a built-in receiver that allows you to choose
the accuracy your application requires from +/-20 cm to +/-2.5 cm pass-to-pass, year-to-year. When you need a DGPS
guidance system that saves you time, fuel and inputs, look no further than the FM-750.
20.3 CM TOUCH SCREEN
With an all new intuitive user experience.
VIRTUAL LIGHTBAR
A virtual lightbar gives you quick on-line
feedback.
ATTACHABLE RTK RADIO
DUAL EXTERNAL VIDEO INPUT
BUILT-IN 220 CHANNEL GNSS RECEIVER
that is GPS and GLONASS capable
CAPABLE OF WIRELESS DATA TRANSFER
between the field and office using Connected
Farm solutions
FM-1000
The FM-1000™ brings you the best performance and reliability with the industry leading dual integrated
GPS + GLONASS receivers. Capable of handling everything you need in guidance, steering, mapping at your fingertips
the FM-1000™ gives you a choice of accuracy between +/-20 cm and +/-2.5 cm pass-to-pass and year-to-year.
LARGE 30.73 CM TOUCH SCREEN
Best visibility from a bright and large screen.
Toggle between plan and 3D views or zoom
in/out with just a tap of your finger.
FREEFORM™ GUIDANCE PATTERN
Offers the ultimate in guidance flexibility,
allowing you to work in different patterns and
shapes that best fit the layout and contours
of your field.
FIELDFINDER TECHNOLOGY
Automatically locate stored fields as you
drive near them.
SUPPORTS FIELD-Iq CROP INPUT
CONTROL SYSTEMS FOR SPRAYING,
SPREADING, STRIP TILL AND PLANTING
GUIDANCE OPTIONS (FM-750 & FM-1000)
• Manual – Lightbar
• Assited – EZ-Steer®
• Integrated autoguidance – AutoPilot™ – On autoguidance ready machines or as a retrofit package
IMPLEMENT CONTROL (FM-750 & FM-1000)
• Planter and sprayer monitoring and control
• TrueGuide: correct the position of your tractor to keep the implement on path (FM-1000 only)
• TrueTracker: correct the position of your implement to keep it on path (FM-1000 only)
INTERNAL RADIO (OPTIONAL)
Integrated 900MHz radio for RTK accuracy.
GNSS DUAL RECEIVERS (OPTIONAL)
Two GPS receivers provide you with ultimate precision for both your tractor and the implement you are pulling when you
need it most.
10 11
INTEGRATED GUIDANCE
AUTOPILOT™ RETROFIT INSTALLATION
AUTOPILOT – PRECISION YOU DEMAND
The Autopilot™ automated steering system used with an RTK signal will give a +/-2.5 cm repeatability from plant to
harvest with any field pattern. The AutoPilot™ system can be integrated into most brands of tractor and harvesting machinery.
Using the machine’s electro hydraulic circuit to provide automatic guidance, this retrofit solution will significantly
increase your efficiency during field preparation, planting and harvesting by driving more accurately and consistently
during extended periods behind the wheel.
DISPLAY
FM-750 or FM-1000 delivering down to
+/-2.5 cm GPS accuracy with RTK technology.
NAVIGATION CONTROLLER II
The industry leading T3™ terrain compensated
corrections (roll + pitch + yaw) and precise
steering instructions to the vehicle by using
guidance and DGPS information from the
FM-1000™ or the FM-750™
AUTOSENSE™ STEERING SENSOR
This unique steering sensor measures highly
accurate wheel angle information on all terrain
and sends it to the Navigation Controller II
providing faster correction and increased
steering accuracy.
IMPLEMENT GUIDANCE AND RTK INCREASE YOUR ACCURACY AND YIELDS
Thanks to a DGPS antenna mounted on the implement, the TrueGuide™ & TrueTracker™ systems keep your implement
on a repeatable path on sloped fields with steep gradients. Retrofit installation kits are compatible with all manufactures’
implements.
TRUE GUIDE – IMPLEMENT CONTROL
The TrueGuide™ implement guidance system uses
the existing Autopilot™ system to improve implement
accuracy. There is no need to hang additional
steering equipment on the implement just to get
better control. Let the tractor guide the implement.
Minimise the downdraft effect on severe hillsides. Let
your Autopilot system pull the implement up the hill
and hold the line. FM-1000 compatible.
TRUE TRACKER – TAKE FULL CONTROL
The TrueTracker™ system is an independent
navigation system that works with the Autopilot
system to provide you the highest level of accuracy.
The TrueTracker system independently steers the
implement using one of many hydraulic solutions on
a repeatable path even on extreme slopes and
variable soils. Maintain accuracy on rolling terrain
using T3™ terrain compensation technology mounted
on the implement. FM-1000 compatible.
ANTENNA
Mounts on to the tractor, combine or implement
to provide up to +/-2.5 cm pass-to-pass and
year-to-year accuracy
VEHICLE INTERFACE
Receives navigation commands from the
Navigation Controller II which controls the
vehicle’s steering when engaged.
RTK BASE STATION
An RTK base station includes a DGPS antenna,
receiver and radio link to provide RTK correction
signals to the auto-guidance system.
EZ-REMOTE
The EZ-Remote joystick mounts to any tractor
console, providing an even more convenient way to
control a variety of guidance display functions from
the cab.
Enhances a wide range of tasks, from basic
guidance operations to more advanced operations
like manual offset of the scraper in field levelling
applications.
12 13
INTELLISTEER – THE NEW HOLLAND
INTEGRATED GUIDANCE PACKAGE
INTELLISTEER™ AUTOMATIC STEERING SYSTEM
IntelliSteer is a fully integrated New Holland designed
and developed Automatic Steering System. Available
from the factory or as retrofit package, the IntelliSteer™
system offers fully automated steering with repeatability
and precision. With features including RTK accuracy,
IntelliSteer helps you maximize productivity for optimal
crop yields.
Using DGPS Technology and fully integrated control
systems the IntelliSteer™ system helps ensure parallel
pass to pass accuracy of up to +/-2.5cm*. The
IntelliSteer™ system is ideal for seeding and planting in
the most demanding situations and dramatically
improves operator performance and comfort.
The New Holland IntelliSteer™ System uses built
in steering angle sensors to keep the Navigation
Controller II informed of wheel direction. Also integrated
into the hydraulic system is a control valve which
converts the signals from the Navigation Controller II into
hydraulic movements of the steering system.
An additional benefit of using RTK correction with the
IntelliSteer™ system is the guaranteed year-to-year
repeatability, which is becoming more important with
today’s modern farming techniques. IntelliSteer with RTK
is ideal for Controlled Traffic Farming (CTF) practices.
All this and more at the touch of a button.
*Using RTK correction signal.
NEW HOLLAND INTEGRATED STEERING SENSOR
Measures highly accurate wheel angle information on all
terrain and sends it to the Navigation Controller II.
NAVIGATION CONTROLLER II
The industry leading Navigation Controller II is the main
control system which continually corrects for roll, pitch, and
yaw by using state of the art 6-axis solid state inertial
sensors to give you a true on-ground position.
NEW HOLLAND VEHICLE INTERFACE
Receives navigation commands from the Navigation
Controller II which control the vehicle’s steering when
engaged.
INTELLIVIEW™ III MONITOR
The IntelliView™ III colour touch screen Monitor enables
the programming and personalising of settings for auto
guidance, and provides the visual interface when
operating the IntelliSteer ™ System.
The IntelliSteer™ System, when linked to the
intelliView™ III Monitor ,can perform a number of
different steering patterns.
NH 262 RECEIVER
The New Holland 262 antenna receives the DGPS signals to
guide the vehicle. This antenna can easily be transferred
from tractor to tractor or even to your combine. For RTK
applications a slim profile radio mounts underneath the
receiver.
RTK BASE STATION
An RTK base station includes a GPS antenna, receiver and
radio link to provide RTK correction signals to tractormounted auto-guidance systems and can be either portable
or permanently mounted.
14 15
INTELLIVIEW III – DISPLAY PRECISION FARMING –
INTEGRATED PACKAGE
INTELLIVIEW™ III TOUCHSCREEN
The Intelliview™ III display can be used throughout a
farming operation and is fitted as standard
equipment on your New Holland T7, T8 or T9 tractors
as well as CX8000 and CR9000 combines.
The Intelliview™ III will communicate with and
display machine function information in real time on
just one screen.Maximum operator comfort is
provided on a 17.8 cm touch screen display, see
where you are and choose information you want to
view, monitor and control.
All the information you need at a glance, from
• Fingertip adjustment of all key settings and
compatible with the New Holland IntelliSteer™
guidance system.
• Monitor and record field performance operations
such as area and distance, fuel usage, hectares
per hour and engine efficiencies, slip and work
rate.
• Full ISOBUS integration – Intelliview™ III will
serve as a virtual terminal for any ISO11783
compliant implement
• Yield, moisture and grain temperature monitoring
• Automatic crop setting monitoring and control
• On-screen real-time mapping.
• Up to three cameras can be linked to the
IntelliView™ III system, perfect for monitoring
implements and avoiding blind spots.
MAXIMISE CUSTOMER PROFITABILITY
New Holland offers a Precision Farming package that is integrated into the combines’ control system.
INTEGRATED NEW HOLLAND SYSTEMS HELP INCREASE YIELDS
Precision farming is integrated into the design of CX8000 & CR9000 combines to provide you with information to
maximise crop and equipment performance. New Holland Precision Land Management equipment is factory installed.
Standard equipment includes
•Yield and moisture monitor for on-the-go yield and moisture readings with data logging.
•Yield and moisture monitor with a DGPS receiver to set you up with on-screen yield mapping with data logging.
•Optional equipment includes the NH262 DGPS with IntelliSteer™ auto guidance.
YIELD MEASUREMENTS WITH LESS
CALIBRATION
New Holland’s exclusive, patented yield mass sensor
design allows accuracy with one crop, one load
calibration. The grain mass flow sensor measures all
the grain continuously for more accurate yield
measurements. The sensor plate is mounted at the
top of the grain elevator and incorporates a pivoting
device and counterweight. This design keeps the
system balanced when working on slopes, and
reduces the friction effect of various grain moistures
and densities to ensure a precise measurement.
Unlike other yield measurements systems, there’s no
need to re-calibrate when you change crops.
The New Holland system requires calibration only
once per season in one crop.*
POSITION SIDEWIDER II –
EXACTLY WHERE YOU WANT IT
The SideWinder™ II* armrest adjusts via the touch of
a button.
It can be quickly moved by the operator to suit
individual preference. It can also be easily moved to
match different applications.
*T7 / T8 / T9 tractor models
PLUG AND PLAY ISO BUS COMPATIBILITY
The IntelliView™ III in-cab information monitor can do so much more than detail tractor functions.
Fully ISO BUS compatible, it can be used to operate a range of equipment to include balers and sprayers.
This saves the need for a separate control within the cab and reduces the time to switch between jobs.
REAL TIME MOISTURE SENSING
New Holland’s moisture sensor measures grain
moisture in real time. Samples are taken every 30
seconds and the data is sent to the IntelliView™ III
monitor. Sensor calibration is required for each crop
type.
LIVE ON SCREEN MAPPING
The IntelliView™ III monitor allows the display of yield,
moisture, fuel usage and coverage maps as you harvest.
16 17
PRECISION FARMING MAP IT, ANALYSE IT AND PRINT IT
CX8000 & CR9000 combines equipped with the
New Holland’s DGPS system allows you to use the
valuable field data you collect with the yield and
moisture sensors to prepare yield maps and better
understand yield variations. Yield and moisture
readings are stored on a USB flash drive, which
you can download into your desktop computer.
Using New Holland’s Precision Farming Software,
the data can be viewed and thoroughly analysed.
The desktop software allows for mapping and
data conversion from the yield monitor system and
is capable of reading and processing yield data
from many competitive brand systems. From such
analysis, prescriptive maps can be constructed for
variable rate application.
P
d
l
e
i
Y
S
n
o
i
t
c
e
t
o
r
r
o
s
n
e
M
M
o
o
i
n
s
t
u
r
e
i
t
o
r
D
a
t
a
S
e
n
o
i
t
a
s
i
l
i
t
r
e
F
e
d
i
n
g
C
Y
o
m
p
u
t
d
l
e
i
e
r
D
e
M
s
k
t
o
p
p
a
C
u
l
t
i
v
a
t
i
o
n
C
D
a
t
a
a
r
d
P
r
c
s
e
r
a
M
n
o
i
t
p
i
s
p
S
A
o
n
l
i
s
i
s
y
l
a
All New Holland machinery can utilise the data
collected from the IntelliView family of monitors.
Guidance lines can be easily created and
transferred between vehicles so that all machines
entering the field use exactly the same tramlines
throughout the crop cycle. If an AutoPilot Kit is
fitted to another brand of machinery, again
information can be transferred between that, the
PFS Desktop Software and the New Holland family
of monitors.
18 19
PRECISION FARMING – VARIABLE RATE PRECISION FARMING – PLM PORTAL
FIELD-Iq CROP INPUT CONTROL SYSTEM
The Field-IQ™ crop input control system is a section control and variable rate application control system that is simple
to install and use. It prevents seed and fertilizer overlap and controls the rate of seed, liquid or granular materials. The
Field-IQ system is compatible with the FM-1000™ integrated display and the FM-750 system.
PROFESSIONAL CUSTOMER SUPPORT
To support New Holland customers who have purchased Precision Farming and Auto Guidance products, a purpose
built website called the PLM Portal has been created.
The PLM Portal is available to all New Holland customers and can be accessed from the following web address:
www.newhollandplm.com
Once you have signed into the website you can gain access to advanced information on all New Holland Precision
Farming and Auto Guidance systems.
For New Holland’s Precision Farming software customers, a purpose built section of the website provides training videos
and information for customer support.
PREVENT SEED AND FERTILIZER OVERLAP WITH FIELD-Iq SECTION CONTROL
• Automatically control up to 48 rows individually for maximum savings in seed and increased yields
• Eliminate seed overlap in your headlands and point rows with TruCount Meter Mount™ air clutches
• Eliminate fertilizer overlap with the new TruCount LiquiBlock™ valves that easily connect to clutch air lines
VARY SEED POPULATION IN YOUR FIELD WITH FIELD-Iq VARIABLE RATE CONTROL
AND RAWSON™ DRIVES
• Adjust your seed population manually or using a prescription map delivered from your precision farming
software (PFS)
• Apply a high population to fertile or well irrigated soils to maximize yield potential while reducing the rate on
less fertile or poorly irrigated soils
VARY THE RATE OF FERTILIZER OR LIME,
USING FIELD-Iq VARIABLE RATE CONTROL
AND RAWSON DRIVES
• Apply the correct amount of lime to manage your
soil’s PH in every location
TAILORED TRAINING
Customers who have purchased a PLM-Support Package will receive a special PLM key which will enable them to
sign-up for training courses and access individual on-line support for the Precision Farming Desktop software.
EXPERTS IN OUR FIELD – PRECISION IN YOURS
AT YO UR OWN DE AL ER
YOUR SUCCESS - OUR SPECIALTY
Visit our web site at: www.newholland.com / www.newhollandplm.com
31-53 Kurrajong Road, St Marys NSW 2760
tel: +61 2 9673 7777
Safety begins with a thorough understanding of the
equipment. Always make sure you and your operators
read the Operator’s Manual before using the
equipment. Pay close attention to all safety and
operating decals and never operate machinery
without all shields, protective devices and
structures in place.
The data indicated in this folder are approximate. The models described here can be subjected to modifications without any notice by the manufacturer.
The drawings and photos may refer to equipment that is either optional or intended for other countries. Please apply to our Sales Network for any further
information. Published by New Holland Brand Communications. Bts Adv. - Printed in Australia - NH PLM 08/10
Loading...