Thank you for choosing NETGEAR.
After installing your device, locate the serial number on the label of your product and use it to register your product
at https://my.netgear.com. You must register your product before you can
NETGEAR recommends registering your product through the NETGEAR w
support, visit http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the li
http://support.netgear.com/general/contact/d
NETGEAR recommends that you use only the official NETGEAR support resources.
For more information about the topics covered in this manual, visit the suppo
http://suppo
rt.netgear.com or http://downloadcenter.netgear.com.
rt website at
5
NeoTV Streaming Player
Streaming Basics
For the optimal media streaming experience with the streaming player, NETGEAR
recommends the following:
• Broadba
need a connection with a speed of 2 to 3 Mbps or faster. The faster your connection, the
better the quality. For high-quality video and audio, a connection of least 3 Mbps is
required, and for HD 1080p movies, 6 Mbps or faster is recommended.
Note: Streaming quality also depends on the Internet connection quality;
You can test your bandwidth at one of the following sites:
www.speakeasy.net/speedtest
www.speedtest.net
Or you can sign up for the VUDU service, and ru
Settings.
• Network conne
Internet connection using a wired or wireless (WiFi) connection. You might need a
network router or access point if your cable or DSL modem does not have free ports or
wireless support.
• Internet access through your network. The
through your home network using either a wireless connection or, if you prefer, an
Ethernet cable. For wireless connections, the streaming player follows the WiFi standard
and is compatible with 802.11b, 802.11g, and 802.11n networks—the most common WiFi
networks, depending on your specific model. The streamin g player also support s wireless
security, including WEP, WPA, and WPA2.
nd Internet s
sometimes higher bandwidth is required to prevent packet loss.
ctions.
ervice. To watch m ovies instantly on the streaming player, you
n Network S
You can connect your streaming player to your broadband
streaming player connects to the Internet
peed Test, available under
Getting Started
6
Hardware Features
Power adapter
NeoTV Streaming Player
Installation guide
Remote control
with AAA batteries
Power connector
Ethernet port
HDMI port
Reset button
What Is Included in the Box
NeoTV Streaming Player
Front and Rear Views
Getting Started
7
NeoTV Streaming Player
HDMI
cable
Streaming player
TV
What You Need to Use Your Streaming Player
• TV with HDMI port
• HDMI cable
• Broadband Internet connection
• A wireless or wired network
Installation
To install your streaming player, you connect it to the TV and to your home network. When
you turn on the TV, the NeoTV Quick Setup screen displays.
Connect to the TV
1. Make sure that your TV is on and set to display the correct video input.
2. Connect an HDMI cable
the HDMI IN port on your TV.
(sold separately) to the HDMI port on your streaming player and to
3. Connect th
e power adapter to your player, and plug it into an electrical outlet.
Remote Control Batteries
To use the remote control, remove the battery cover, and insert the two AAA batteries that are
included in the box.
Getting Started
8
NeoTV Streaming Player
Router
Ethernet cable
Streaming player
TV
Connect to Your Home Network
To use your player, you need to connect it to your home network with either a wireless or a
wired connection. After you get your network ready, the onscreen guided setup helps you
connect your player to your network.
Wired Connection
Use an Ethernet cable (sold separately) to connect your player to a LAN port on your router.
Figure 1. Wired LAN connection
Getting Started
9
NeoTV Streaming Player
Wireless router
Streaming player
TV
Wireless Connection
If you are using a wireless connection, place your player within range of your wireless
network. For best wireless reception, avoid enclosing your player in a cabinet.
Figure 2. Wireless network connection
If you do not receive a strong signal during the onscreen setup, rotate your player or move it
closer to your router.
Reset Button
There is a Reset button on the back of the streaming player. Use the Reset button to reset
the streaming player to factory default settings.
To reset to factory default settings, press and hold Reset f
turns off, turns back on, and restores the default settings.
or 6 seco
nds. The streaming player
Getting Started
10
Remote Control
Power
Confirm/
Down
Stop
Rewind
Next
Home/
Back
Menu
Play/Pause
Right
Left
Up
Previous
Fast Forward
Red button
Green button
Blue button
Yellow button
Enter
Exit Channel
Channel
Quick Start
NeoTV Streaming Player
Figure 3. Remote control
Table 1. Remote control buttons
ButtonDescription
PowerTurns power to the streaming player on and off.
Home/Exit ChannelGo to the home screen or exit the channel.
UpNavigate up.
DownNavigate down.
LeftNavigate left.
RightNavigate right
OKConfirm or enter.
BackReturn to the previous menu. Some services do not use this
button.
Getting Started
11
NeoTV Streaming Player
Table 1. Remote control buttons (continued)
ButtonDescription
MenuAdditional options. Some channels do not use this button.
Play/PausePlay or pause media.
Fast ForwardFast forward.
RewindRewind.
NextSkip to next. Some services do not use this button.
PreviousPrevious movie chapter. Some services do not use this button.
StopStop playing media.
Note: The functions of the color buttons (red, green, blue, and yellow) at
the corners of the directional pad depend on the screen that is
displayed.
Getting Started
12
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.