NETGEAR MS510TXM, MS510TXUP Installation Manual
Hardware Installation Guide
8-Port Multi-Gigabit/10G Ethernet
(Ultra60 PoE++) Smart Managed Pro Switch
with 2 SFP+ Ports
Models
MS510TXM
MS510TXUP
NETGEAR, Inc.
350 E. Plumeria DriveJanuary 2021
San Jose, CA 95134, USA202-12153-01
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
Support and Community
Visit netgear.com/support to get your questions answered and access the latest
downloads.
You can also check out our NETGEAR Community for helpful advice at
community.netgear.com.
Regulatory and Legal
Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français
canadien à https://www.netgear.com/support/download/.
(If this product is sold in Canada, you can access this document in Canadian French at
https://www.netgear.com/support/download/.)
For regulatory compliance information including the EU Declaration of Conformity, visit
https://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.
By using this device, you are agreeing to NETGEAR’s Terms and Conditions at
https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the
device to your place of purchase within your return period.
Do not use this device outdoors. The PoE source is intended for intra building connection
only.
Trademarks
© NETGEAR, Inc., NETGEAR, and the NETGEAR Logo are trademarks of NETGEAR, Inc.
Any non-NETGEAR trademarks are used for reference purposes only.
Revision History
CommentsPublish DatePublication Part
Number
First publication.January 2021202-12153-01
2
Contents
Chapter 1 Introduction
Overview................................................................................................6
Features.................................................................................................6
Safety instructions and warnings........................................................8
Chapter 2 Hardware Overview
Hardware overview of model MS510TXM......................................12
Front panel model MS510TXM....................................................12
LEDs model MS510TXM...............................................................13
Back panel model MS510TXM.....................................................13
Hardware overview of model MS510TXUP.....................................14
Front panel model MS510TXUP..................................................14
LEDs model MS510TXUP..............................................................15
Back panel model MS510TXUP...................................................16
Switch hardware interfaces...............................................................17
RJ-45 ports for 100/1000M and 2.5G/5G/10G BASE-T Ethernet
connectivity.....................................................................................17
Transceiver modules and cables for SFP+ fiber ports..............18
Multi-function Reset button..........................................................18
PoE port capacities and budget for model MS510TXUP..........19
Chapter 3 Applications
Multispeed PoE++ and PoE+ access points and cameras............22
Multispeed backbone switching.......................................................23
10G network storage and redundancy............................................24
Chapter 4 Installation
Step 1: Prepare the site......................................................................26
Step 2: Protect against electrostatic discharge..............................26
Step 3: Unpack the switch.................................................................27
Step 4: Install the switch....................................................................28
Install the switch in a rack..............................................................28
Install the switch on a flat surface.................................................29
Optional Step 5: Install an SFP transceiver module or cable........29
Step 6: Connect devices to the switch.............................................30
Step 7: Check the installation...........................................................31
3
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
Step 8: Apply power and check the LEDs.......................................31
Step 9: Manage the switch................................................................32
Chapter 5 Troubleshooting
Troubleshooting chart.......................................................................36
PoE troubleshooting suggestions....................................................37
Additional troubleshooting suggestions.........................................38
4
1
Introduction
This hardware installation guide complements the installation guide that came with your
switch and applies to the following NETGEAR switch models:
MS510TXM: 8-Port Multi-Gigabit/10G Ethernet Smart Managed Pro Switch with 2
•
SFP+ Ports
MS510TXUP: 8-Port Multi-Gigabit/10G Ethernet Ultra60 PoE++ Smart Managed
•
Pro Switch with 2 SFP+ Ports
The switch provides eight Gigabit Ethernet multispeed copper ports and two dedicated
SFP+ fiber uplink ports that support 1G and 10G. Four of the multispeed copper ports
support 100M, 1G, and 2.5G and each of the other four multispeed copper ports
supports 100M, 1G, 2.5G, 5G, and 10G.
Model MS510TXUP can provide Ultra60 PoE++ (802.3bt) on its eight multispeed copper
ports so that you can let the switch deliver power to PoE++ devices such as WiFi 6 access
points, security cameras, PoE speakers, and LED lighting. Model MS510TXUP can supply
up to 60W PoE++ to each copper port, with a maximum PoE power budget of 295W
across all active PoE++ ports.
This chapter serves as an introduction to the switch and includes the following sections:
• Overview
• Features
• Safety instructions and warnings
Note: For more information about the topics that are covered in this manual, visit the
support website at netgear.com/support.
Note: For technical specifications, see the data sheet at
netgear.com/business/products/switches/smart. For switch documentation, including
the installation guide and user manual, visit netgear.com/support/download.
5
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
Overview
The switch provides eight Gigabit Ethernet multispeed copper ports and two dedicated
SFP+ fiber uplink ports that support 10G and 1G. Four of the multispeed copper ports
support both 1G and 2.5G and each of the other four multispeed copper ports supports
1G, 2.5G, 5G, and 10G. All copper ports use RJ-45 connectors.
The SFP+ ports require standard small form-factor pluggable (SFP) gigabit interface
converters (GBICs, also referred to as a transceiver modules), which are sold separately
from the switch. The switch integrates 140 Gbps line-rate, full-duplex, nonblocking
switch fabric.
The PoE model supports Ultra60 PoE++ (802.3bt) on all copper ports (that is, up to 60W
PoE++ to each port) with a maximum PoE power budget of 295W across all active PoE++
ports.
Note: For information about application examples, see Applications on page 21.
You can install the switch freestanding or rack mounted in a wiring closet or equipment
room. The switch is IEEE compliant and offers low latency. All ports can automatically
negotiate to the highest speed, which makes the switch very suitable for a mixed
environment with multispeed Gigabit Ethernet, Gigabit Ethernet, and Fast Ethernet.
For speeds of 10 Gbps, use Category 6 (Cat 6) cables terminated with RJ-45 connectors;
for speeds from 5 Gbps to 10 Gbps, use Cat 5e cables terminated with RJ-45 connectors;
and for speeds from 10 Mbps to 5 Gbps, including 2.5 Gbps, use Cat 5e or higher-rated
Ethernet cables terminated with RJ-45 connectors.
Features
The switch supports the following key hardware features:
Four multispeed Ethernet ports (5–8), each of which supports 10G, 5G, 2.5G, 1G,
•
and 100M.
Four multispeed Ethernet ports (1–4), each of which supports 2.5G, 1G, and 100M.
•
Two dedicated SFP+ fiber uplink ports (9F and 10F), each of which is capable of 10G
•
and 1G.
PoE support for model MS510TXUP:
•
- Eight Ultra60 PoE++ (802.3bt) ports
-
Total PoE power budget of 295W for the switch
Hardware Installation Guide6Introduction
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
MAC table size of 32K.
•
Two fans for model MS510TXM and three fans for model MS510TXUP with
•
variable-speeds that can lower the noise level during low temperatures.
Acoustic noise at 25°C is equal to or less than 25 dBA for model MS510TXM and 33
•
dBA for model MS510TXUP.
140 Gbps line-rate, full-duplex, nonblocking switch fabric.
•
Includes 19-inch rack-mount kit for rack installation.
•
Full compatibility with IEEE standards:
•
- IEEE 802.3 Ethernet
- IEEE 802.3u 100BASE-T
- IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX
- IEEE 802.3bz NBASE-T and MGBASE-T
- IEEE 802.3an (10GBASE-T)
-
IEEE 802.3ae 10-Gigabit Ethernet over fiber (10GBASE-SR, 10GBASE-LR)
- IEEE 802.3ab 1000BASE-T
- IEEE 802.3i 10BASE-T
- IEEE 802.1Q VLAN tagging
-
IEEE 802.3x Full-duplex flow control
- IEEE 802.3ad Link aggregation (LAG with LACP)
- IEEE 802.1ab LLDP
-
IEEE 802.1p Class of Service (QoS)
- IEEE 802.1D Spanning Tree Protocol (STP)
- IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
- IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
- IEEE 802.1x RADIUS network access control
-
IEEE 802.3az Energy Efficient Ethernet (EEE)
-
IEEE 802.1af (PoE, model MS510TXUP)
- IEEE 802.1at (PoE+, model MS510TXUP)
- IEEE 802.1bt (PoE++, model MS510TXUP)
AutoSensing and autonegotiating capabilities for all ports.
•
Auto Uplink™ technology is supported on all ports.
•
Hardware Installation Guide7Introduction
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
Automatic address learning function to build the packet-forwarding information
•
table. The table contains up to 32K Media Access Control (MAC) addresses.
Store-and-forward transmission to remove bad packets from the network.
•
Active flow control to minimize packet loss and frame drops.
•
Half-duplex backpressure control.
•
Per-port status LEDs and system status LEDs.
•
NETGEAR green power-saving features:
•
-
Energy efficiency mode that fully conforms to the IEEE802.3az standard
- Per-port automatic change to a lower power mode when the port link is down
Safety instructions and warnings
Use the following safety guidelines to ensure your own personal safety and to help
protect your system from potential damage.
To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,
observe the following precautions:
This product is designed for indoor use only in a temperature-controlled and
•
humidity-controlled environment. Note the following:
-
For more information about the environment in which this product must operate,
see the environmental specifications in the appendix or the data sheet.
-
If you want to connect the product to a device located outdoors, the outdoor
device must be properly grounded and surge protected, and you must install an
Ethernet surge protector inline between the indoor product and the outdoor
device. Failure to do so can damage the product.
-
Before connecting the product to outdoor cables or devices, see
https://kb.netgear.com/000057103 for additional safety and warranty information.
Failure to follow these guidelines can result in damage to your NETGEAR product,
which might not be covered by NETGEAR’s warranty, to the extent permissible by
applicable law.
Observe and follow service markings:
•
- Do not service any product except as explained in your product documentation.
Some devices should never be opened.
-
If applicable to your product, opening or removing covers that are marked with
the triangular symbol with a lightning bolt can expose you to electrical shock.
Hardware Installation Guide8Introduction
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
We recommend that only a trained technician services components inside these
compartments.
If any of the following conditions occur, unplug the product from the power outlet,
•
and then replace the part or contact your trained service provider:
- Depending on your product, the power adapter, power adapter cable, power
cable, extension cable, or plug is damaged.
-
An object fell into the product.
- The product was exposed to water.
- The product was dropped or damaged.
-
The product does not operate correctly when you follow the operating
instructions.
Keep the product away from radiators and heat sources. Also, do not block cooling
•
vents.
Do not spill food or liquids on your product components, and never operate the
•
product in a wet environment. If the product gets wet, see the appropriate section
in your troubleshooting guide, or contact your trained service provider.
Do not push any objects into the openings of your product. Doing so can cause fire
•
or electric shock by shorting out interior components.
Use the product only with approved equipment.
•
If applicable to your product, allow the product to cool before removing covers or
•
touching internal components.
Operate the product only from the type of external power source indicated on the
•
electrical ratings label. If you are not sure of the type of power source required,
consult your service provider or local power company.
To avoid damaging your system, if your product uses a power supply with a voltage
•
selector, be sure that the selector is set to match the power at your location:
-
115V, 60 Hz in most of North and South America and some Far Eastern countries
such as South Korea and Taiwan
- 100V, 50 Hz in eastern Japan and 100V, 60 Hz in western Japan
-
230V, 50 Hz in most of Europe, the Middle East, and the Far East
Be sure that attached devices are electrically rated to operate with the power available
•
in your location.
Depending on your product, use only a supplied power adapter or approved power
•
cable:
Hardware Installation Guide9Introduction
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
If your product uses a power adapter:
-
If you were not provided with a power adapter, contact your local NETGEAR
reseller.
-
The power adapter must be rated for the product and for the voltage and current
marked on the product electrical ratings label.
If your product uses a power cable:
-
If you were not provided with a power cable for your system or for any
AC-powered option intended for your system, purchase a power cable approved
for your country.
-
The power cable must be rated for the product and for the voltage and current
marked on the product electrical ratings label. The voltage and current rating of
the cable must be greater than the ratings marked on the product.
To help prevent electric shock, plug the system and peripheral power cables into
•
properly grounded power outlets.
If applicable to your product, the peripheral power cables are equipped with
•
three-prong plugs to help ensure proper grounding. Do not use adapter plugs or
remove the grounding prong from a cable. If you must use an extension cable, use
a three-wire cable with properly grounded plugs.
Observe extension cable and power strip ratings. Make sure that the total ampere
•
rating of all products plugged into the extension cable or power strip does not
exceed 80 percent of the ampere ratings limit for the extension cable or power strip.
To help protect your system from sudden, transient increases and decreases in
•
electrical power, use a surge suppressor, line conditioner, or uninterruptible power
supply (UPS).
Position system cables, power adapter cables, or power cables carefully. Route
•
cables so that they cannot be stepped on or tripped over. Be sure that nothing rests
on any cables.
Do not modify power adapters, power adapter cables, power cables or plugs. Consult
•
a licensed electrician or your power company for site modifications.
Always follow your local and national wiring rules.
•
Hardware Installation Guide10Introduction
2
Hardware Overview
This chapter describes the switch hardware features.
The chapter includes the following sections:
• Hardware overview of model MS510TXM
• Hardware overview of model MS510TXUP
• Switch hardware interfaces
11
8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports
Hardware overview of model MS510TXM
Model MS510TXM provides eight Gigabit Ethernet multispeed copper ports and two
dedicated SFP+ fiber uplink ports that support 10G and 1G. Four of the multispeed
copper ports support 2.5G, 1G, and 100M and each of the other four multispeed copper
ports supports 10G, 5G, 2.5G, 1G, and 100M.
Front panel model MS510TXM
The following figure shows the front panel of model MS510TXM.
Figure 1. Front panel model MS510TXM
The following table describes the components on the front panel from left to right. The
components are clearly labeled on the front panel.
Table 1. Front panel components model MS510TXM
DescriptionComponent
System LEDs
Ports 1, 2, 3, and 4
Ports 5, 6, 7, and 8
Power LED and Fan LED.
For more information about the LEDs, see LEDs model MS510TXM on page 13.
Recessed multi-function Reset button (see Multi-function Reset button on page 18).Reset button
Four independent 2.5GBASE-T RJ-45 ports that also support 100/1000BASE-T. Each
port provides a left LED that functions as the combined link, speed, and activity LED.
(The port does not provide a right LED.)
For more information about the LEDs, see LEDs model MS510TXM on page 13.
Four independent 2.5G/5G/10GBASE-T RJ-45 ports that also support 100/1000BASE-T.
Each port provides a left LED that functions as the combined link, speed, and activity
LED. (The port does not provide a right LED.)
For more information about the LEDs, see LEDs model MS510TXM on page 13.
Ports 9F and 10F
Two independent SFP+ ports in which you can install transceiver modules and direct
attach cables (see Transceiver modules and cables for SFP+ fiber ports on page 18).
These ports support 10G or 1G fiber transceiver modules. Each port provides a single
LED that functions as the combined link, speed, and activity LED.
For more information about the LEDs, see LEDs model MS510TXM on page 13.
Hardware Installation Guide12Hardware Overview
Loading...