NETGEAR JR6150 User Manual
Installation Guide
AC750 Wireless Dual Band Gigabit Router JR6150
Package Contents
Step 1. Step 2. Step 3.
Step 4. Step 5. Step 6.
Unplug the power
to turn off your modem.
Connect one end of the blue
Ethernet cable to your modem,
and the other end to the Internet
port on your router.
Plug in, then turn on your modem.
Connect the power adapter to the
router, then plug it into an outlet.
Wait until the Wireless LED turns
solid green.
Connect the router
to your computer.
Open a browser.
Power adapter Ethernet cable
AC750 Wireless Dual Band Gigabit Router
Internet
DSL
or Cable
Modem
AC750 Wireless Dual
Band Gigabit Router
(not included)
Wait approximately 2 minutes
until your modem turns on.
If your modem has a battery backup,
first remove and reinsert the battery
before connecting your modem to power.
If none of the LEDs light, make sure that the
Power On/Off button is in the on position
(pushed in).
Use another Ethernet cable to establish
a wired connection as shown in this diagram.
(Optionally) Connect wirelessly by using the
preset wireless security settings located
on the bottom label.
If the web page does not display,
close and reopen the browser and
enter http://www.routerlogin.net
in the address bar, or check the
“Troubleshooting” chapter of the
user manual.
Power
On/Off
April 2013
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change
without notice. © NETGEAR, Inc. All rights reserved.
For indoor use only. Valid in all EU member states, EFTA states, and Switzerland.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
Preset Wireless Security
This product has a unique WiFi network name (SSID) and network key (password).
The default SSID and password are uniquely generated for every device (like a
serial number) to protect and maximize your wireless security. This information is
located on the label on the bottom of the product.
NETGEAR recommends that you do not change the preset SSID and password. If
you do change the settings, the information on the bottom of the product does not
apply.
Find the preset wireless settings on your router and record them here:
WiFi network name (SSID) _______________________________
Network key (password) _________________________________
If you change the preset wireless settings, record them here:
Wireless network name (SSID) _______________________________
Network key (password) _____________________________________
If necessary to retrieve or update your password, enter
http://www.routerlogin.net in a web browser and log in using the
default user name (admin) and password (password).
Select Wireless Settings to locate your wireless password.
Connect Wireless Devices to Your Router
Choose either the manual or Wi-Fi Protected Setup (WPS) method to add
wireless computers and other devices to your wireless network.
Manual Method
1. Open the software utility that manages your wireless connections on the
wireless device that you want to connect to your router (smartphone, laptop,
computer, or gaming device). This utility scans for all wireless networks in
your area.
2. Look for the preset NETGEAR wireless network name (SSID), and select it.
The SSID is located on the product label on the bottom of the router.
Note: If you changed the name of your network during the setup process, look for
that network name.
3. Enter the preset password (or your custom password if you changed it), and
click Connect.
4. Repeat steps 1–3 to add other wireless devices.
WPS Method
If your wireless device supports WPS (Wi-Fi Protected Setup), which NETGEAR
calls Push 'N' Connect, you might be prompted to press the WPS button on the
router instead of entering a password. If this happens:
1. Press the WPS button on the router.
2. Within 2 minutes, press the WPS button on the client device, or follow the
WPS instructions that came with your wireless device to complete the WPS
process. The device will then be connected to your router.
3. Repeat this process to add other WPS wireless devices.
Note: WPS does not support WEP security. If you try to connect a WEP client to
your network using WPS, it will not work.
ReadySHARE Printer
ReadySHARE Printer lets you connect a USB printer to the router’s USB port and
access it wirelessly. To set up this feature:
1. Connect the USB printer to the router’s USB port.
2. Download and install the NETGEAR USB Control Center utility at
http://www.netgear.com/landing/en-us/readyshare.aspx. You must install this
utility before you can use the ReadySHARE Printer feature.
3. Follow the instructions in the utility to connect to the printer.
For more information about ReadySHARE Printer, see the JR6150 product
information page at http://www.NETGEAR.com/success/JR6150-en.aspx.
Support
Thank you for selecting NETGEAR products. After installing your device, locate the
serial number on the label of your product and use it to register your product at
https://my.netgear.com. You must register your product before you can use
NETGEAR telephone support. NETGEAR recommends registering your product
through the NETGEAR website. For product updates and web support, visit
http://support.netgear.com. NETGEAR recommends that you use only the official
NETGEAR support resources.
You can get the user manual online at http://downloadcenter.netgear.com or through
a link in the product’s user interface. Download the free Live Parental Controls
centralized Internet site filtering software for your router from
http://www.netgear.com/lpc. For additional features, including traffic metering,
ReadySHARE, guest access, and others, log in to your router at
http://www.routerlogin.net.
For the complete EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
Internet
STATUS GOOD
Network Map
Number of devices 16
Parental Controls
WiFi Connection
STATUS Connected
Router Settings
Click here
ReadySHARE
Click here
Click here
Download the free Desktop NETGEAR genie
Automatically fix common network problems and
easily manage your home network connections.
http://www.NETGEAR.com/genie
Loading...