NETGEAR is a trademark of NETGEAR, Inc.
Microsoft, Windows, and Wi ndow s NT are registered trademar ks of Microsoft Corporation.
Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruct ions, may cause harmf ul interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less
than 20 cm (8 inches) during normal operation.
EN 55 022 Declaration of Conformance
This is to certify that the DG834G 54 Mbps Wireless ADSL Firewall Router is shielded against the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by
the application of EN 55 022 Class B (CISPR 22).
ii
202-10006-01
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß das DG834G 54 Mbps Wireless ADSL Firewall Router gemäß der im BMPT-AmtsblVfg
243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte
(z.B. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der
Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
Certificate of the Manufacturer/Importer
It is hereby certified that the DG834G 54 Mbps Wireless ADSL Firewall Router has been suppressed in accordance
with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for
example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please
refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the second category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver , it may become the cause of radio interference.
Read instructions for correct handling.
Customer Support
Refer to the Support Information Card that shipped with your DG834G 54 Mbps Wireless ADSL Firewall Router .
World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL)
http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer
or Netscape are required.
Thank you for purchasing the NETGEAR™ DG834G 54 Mbps Wireless ADSL Firewall Router .
Audience, Conventions, Scope
This reference manual assumes that the reader has basic-to-intermediate computer and Internet
skills. However, basic computer network, Internet, firewall, and networking technology tutorial
information is provided in the Appendices.
This guide uses the following typographical conventions:
Table 1.Typographical conventions
italicsEmphasis, books, CDs, URL names
bold times romanUser input
courier fontScreen text, file and server names, extensions, commands, IP addresses
Note: This format is used to highlight information of importance or special interest.
This manual is written for the DG834G wireless router according to these specifications:
Note: Product updates are available on the NETGEAR, Inc. Web site at http://
www.netgear.com/support/main.asp. Documentation updates are available on the
NETGEAR, Inc. Web site at http://www.netgear.com/docs.
About This Guide1
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
How to Use this Manual
The HTML version of this manual includes these features.
1
2
3
Figure 1 -1: HTML version of this manual
1. Left pane. Use the left pane to view the Contents, Index, Search, and Favorites tabs.
To view the HTML version of the manual, you must have a version 4 or later browser with
JavaScript enabled.
2. Toolbar buttons . Use the toolbar buttons across the top to navigate, print pages, an d more.
–The Show in Contents button locates the current topic in the Contents tab.
–Previous/Next buttons display the previous or next topic.
–The PDF button links to a PDF version of the full manual.
–The Print button prints the current topic. Using this button when a step-by-step
procedure is displayed will send the entire procedure to your printer—you do not
have to worry about specifying the correct range of pages.
3. Right pane. Use the right pane to view the contents of the manual. Also, each page of the
manual includes a link at the top right which links to a PDF file
containing just the currently selected chapter of the manual.
2About This Guide
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewall Router DG834G
How to Print this Manual
To print this manual you can choose one of the following several options, according to your needs.
•Printing a “How To” Sequence of Steps in the HTML View. Use the Print button on the
upper right side of the toolbar to print the currently displayed topic. Using this button when a
step-by-step procedure is displayed will send the entire procedure to your printer—you do not
have to worry about specifying the correct range of pages.
•Printing a Chapter. Use the link at the top right of any page.
–Click the “PDF of This Chapter” link at the top right of any page in the chapter you want
to print. A new browser window opens showing the PDF version of the chapter you were
viewing.
–Click the print icon in the upper left of the window.
–Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper and printer ink by selecting this feature.
•Printing the Full Manual. Use the PDF button in the toolbar at the top right of the browser
window.
–Click the PDF button. A new browser window opens showing the PDF version of the
chapter you were viewing.
–Click the print icon in the upper left side of the window.
–Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper and printer ink by selecting this feature.
About This Guide3
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
4About This Guide
202-10006-01
Chapter 2
Introduction
This chapter describes the features of the NETGEAR DG834G 54 Mbps Wireless ADSL Firewall
Router . The DG834G wireless router is a combination of a built-in ADSL modem, router, 4-port
switch, 802.11g wireless access point, and firewall which enables your entire network to safely
share an Internet connection that otherwise is used by a single computer.
Note: If you are unfamiliar with networking and routing, refer to Appendix B, “Network
and Routing Basics”, to become more familiar with the terms and procedures used in this
manual.
About the Router
The DG834G 54 Mbps Wireless ADSL Firewall Router provides continuous, high-speed 10/100
Ethernet access between your wireless and Ethernet devices. The DG834G wireless router enables
your entire network to share an Internet connection through the built-in ADSL modem that
otherwise is used by a single computer. With minimum setup, you can install and use the router
within minutes.
The DG834G wireless router provides multiple Web content filtering options, plus e-mail
browsing activity reporting and instant alerts. Parents and network administrators can establish
restricted access policies based on time-of-day, Web site addresses and address keywords, and
share high-speed ADSL Internet access for up to 253 personal computers. The included firewall
and Network Address Translation (NAT) features protect you from hackers.
Introduction2-1
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
Key Features
The DG834G wireless router provides the following features:
•A powerful, true firewall
•802.11g standards-based wireless networking
•Content filtering
•Auto Sensing and Auto Uplink™ LAN Ethernet connections
•Extensive Internet protocol support
•Easy, Web-based setup for installation and management
•A built-in ADSL modem
These features are discussed below.
802.11 Standards-based Wireless Networking
The DG834G wireless router includes an 802.11g-compliant wireless access point, providing
continuous, high-speed 10/100 Mbps access between your wireless and Ethernet devices. The
access point provides:
•802.11g Standards-based wireless networking at up to 100 Mbps
•Works with both 802.11g and 802.11b wireless devices
•64-bit and 128-bit WEP encryption security
•WEP keys can be entered manually or generated by passphrase
•Wireless access can be restricted by MAC address.
A Powerful, True Firewall
Unlike simple Internet sharing NAT routers, the DG834G is a true firewall, using stateful packet
inspection to defend against hacker attacks. Its firewall features include:
•Denial of Service (DoS) protection
Automatically detects and thwarts Denial of Service (DoS) attacks such as Ping of Death,
SYN Flood, LAND Attack and IP Spoofing.
•Blocks unwanted traffic from the Internet to your LAN.
2-2Introduction
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewall Router DG834G
•Blocks access from your LAN to Internet locations or services that you specify as off-limits.
•Logs security incidents
The DG834G will log security events such as blocked incoming traffic, port scans, attacks,
and administrator logins. You can configure the router to email the log to you at specified
intervals. You can also configure the router to send immediate alert messages to your email
address or email pager whenever a significant event occurs.
Content Filtering
With its content filtering feature, the DG834G prevents objectionable content from reaching your
computers. The router allows you to control access to Internet content by screening for keywords
within Web addresses. You can co nfig ure the router to log and report attempts to access
objectionable Internet sites.
Auto Sensing and Auto Uplink™ LAN Ethernet Connections
With its internal 4-port 10/100 switch, the DG834G can connect to either a 10 Mbps standard
Ethernet network or a 100 Mbps Fast Ethernet network. The local LAN ports are autosensing and
capable of full-duplex or half-duplex operation.
The router incorporates Auto Uplink
sense whether the Ethernet cable plugged into the port should have a ‘normal’ connection such as
to a computer or an ‘uplink’ connection such as to a switch or hub. That port will then configure
itself to the correct configuration. This feature also eliminates the need to worry about crossover
cables, as Auto Uplink will accommodate either type of cable to make the right connection.
TM
technology. Each local Ethernet port will automatically
Protocol Support
The DG834G supports Transmission Control Protocol/Internet Protocol (TCP/IP) and Routing
Information Protocol (RIP). Appendix B, “Network and Routing Basics” provides further
information on TCP/IP.
•The Ability to Enable or Disable IP Address Sharing by NAT
The DG834G allows several networked computers to share an Internet account using only a
single IP address, which may be statically or dynamically assigned by your Internet service
provider (ISP). This technique, known as Network Address Translation (NAT), allows the use
of an inexpensive single-user ISP account. This feature can also be turned off completely for
using the DG834G if you want to manage the IP address sche me yourself.
Introduction2-3
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
•Automatic Configuration of Attached Computers by DHCP
The DG834G dynamically assigns network configuration information, including IP, gateway,
and domain name server (DNS) addresses, to attached computers on the LAN using the
Dynamic Host Configuration Protocol (DHCP). This feature greatly simplifies configuration
of computers on your local network.
•DNS Proxy
When DHCP is enabled and no DNS addresses are specified, the router provides its own
address as a DNS server to the attached computers. The router obtains actual DNS addresses
from the ISP during connection setup and forwards DNS requests from the LAN.
•Classical IP (RFC 1577)
Some Internet service providers, in Europe for example, use Classical IP in their ADSL
services. In such cases, the router is able to use the Classical IP address from the ISP.
•PPP over Ethernet (PPPoE)
PPP over Ethernet is a protocol for connecting remote hosts to the Internet over an ADSL
connection by simulating a dial-up connection. This feature eliminates the need to run a login
program such as EnterNet or WinPOET on your computer.
•PPP over ATM (PPPoA)
PPP over ATM is a protocol for connecting remote hosts to the Internet over an ADSL
connection by simulating an ATM connection.
•Dynamic DNS
Dynamic DNS services allow remote users to find your network using a domain name when
your IP address is not permanently assigned. The router contains a client that can connect to
many popular Dynamic DNS services to register your dynamic IP address.
•Universal Plug and Play (UPnP)
UPnP is a networking architecture that provides compatibility among networking technology.
UPnP compliant routers provide broadband users at home and small businesses with a
seamless way to participate in online games, videoconferencing and other peer-to-peer
services.
Easy Installation and Management
You can install, configure, and operate the DG834G within minutes after connecting it to the
network. The following features simplify installation and management tasks:
2-4Introduction
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewall Router DG834G
•Browser-based management
Browser-based configuration allows you to easily configure your router from almost any type
of personal computer, such as Windows, Macintosh, or Linux. A user-friendly Setup Wizard is
provided and online help documentation is built into the browser-based Web Management
Interface.
•Smart Wizard
The router automatically senses the type of Internet connection, asking you only for the
information required for your type of ISP account.
•Remote management
The router allows you to login to the Web management interface from a remote location via
the Internet. For security, you can limit remote management access to a specified remote IP
address or range of addresses, and you can choose a nonstandard port number.
•Diagnostic functions
The router incorporates built-in diagnostic functions such as Ping, DNS lookup, and remote
reboot. These functions allow you to test Internet connectivity and reboot the router. You can
use these diagnostic functions directly from the DG834G when your are connect on the LAN
or when you are connected over the Internet via the remote management function.
•Visual monitoring
The router’s front panel LEDs provide an easy way to monitor its status and activity.
•Flash erasable programmable read-only memory (EPROM) for firmware upgrade
What’s in the Box?
The product package should contain the following items:
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
The Router’ s Front Panel
The DG834G 54 Mbps Wireless ADSL Firewall Router front panel shown below contains status
LEDs.
Power
Test
Wireless Internet
LAN
Figure 2-1: DG834G Front Panel
You can use the LEDs to verify various conditions. Table 2-1 lists and describes each LED on the
front panel of the router. These LEDs are green when lit.
Table 2-1.LED Descriptions
LabelActivityDescription
PowerOn
Off
TestOn
Off
2-6Introduction
Power is supplied to the router.
Power is not supplied to the router.
The system is initializing.
The system is ready and running.
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewall Router DG834G
Table 2-1.LED Descriptions
InternetBlink -- Amber
On -- Green
Blink -- Green
WirelessOn
Off
LANOn (Green)
Blink (Green)
On (Amber)
Blink (Amber)
Off
Indicates ADSL training.
The Internet port has detected a link with an attached device.
Data is being transmitted or received by the Internet port.
Indicates that the Wireless port is initialized.
The Wireless Access Point is turned off.
The Local port has detected link with a 100 Mbps device.
Data is being transmitted or received at 100 Mbps.
The Local port has detected link with a 10 Mbps device.
Data is being transmitted or received at 10 Mbps.
No link is detected on this port.
The Router’s Rear Panel
The rear panel of the DG834G 54 Mbps Wireless ADSL Firewall Router (Figure 2-2) contains
port connections.
54 Mbps Wireless ADSL Firewall Router DG834G
Figure 2-2: DG834G Rear Panel
Viewed from left to right, the rear panel contains the following elements:
•AC power adapter outlet
•Four Local Ethernet RJ-45 ports for connecting the router to the local computers
•Factory Default Reset push button
•ADSL port for connecting the router to an ADSL line
•Wireless antenna
Introduction2-7
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
2-8Introduction
202-10006-01
Chapter 3
Connecting the Router to the Internet
This chapter describes how to set up the router on your Local Area Network (LAN) and connect to
the Internet. It describes how to configure your DG834G 54 Mbps Wireless ADSL Firewall Router
for Internet access using the Setup Wizard, or how to manually configure your Internet connection.
What You Need Before You Begin
You need to prepare the following before you can establish an Internet connection through your
router:
1.The router connected to an ADSL line and a computer properly connected to the router as
explained below.
2.Active Internet service such as that provided by an ADSL account.
3.The Internet Service Provider (ISP) configuration information for your DSL account.
Note: If you purchased the DG834G in a country where a microfilter is not included, you must
acquire one.
ADSL Microfilter Requirements
ADSL technology uses the same wires as your telephone service. However, ADSL adds signals to
the telephone lines which create noise in the telephone service. You must use ADSL microfilters to
filter out these signals before they reach your telephone.
ADSL Microfilter
Phone
Figure 3-1: ADSL microfilter
Connecting the Router to the Internet3-1
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
Each device such as a telephone, fax machine, answering machine, or caller ID display will require
an ADSL microfilter.
Note: Do not connect the DG834G to the ADSL line through a microfilter unless the microfilter is
a combination microfilter/splitter specifically designed for this purpose. Doing so will prevent the
built-in ADSL modem in the DG834G from establishing a connection to the Internet. If you have
any doubts about this, connect the DG834G directly to the ADSL line.
ADSL Microfilter with Built-In Splitter
DSL
Phone
Figure 3-2: ADSL microfilter with built-in splitter
Line
Use an ADSL microfilter with built-in splitter when there is a single wall outlet which must
provide connectivity for both the DG834G and telephone equipment.
Ethernet Cabling Requirements
The DG834G wireless router connects to your Ethernet LAN via twisted-pair cables. If the
computer will connect to your network at 100 Mbps, you must use a Category 5 (CA T5) cable such
as the one provided with your router.
Computer Hardware Requirements
To use the DG834G wireless router on your network, each computer must have an installed
Ethernet adapter and an Ethernet cable, or a 802.11g wireless adapter.
LAN Configuration Requirements
For the initial connection to the Internet and configuration of your router, you need to connect a
computer to the router which is set to automatically get its TCP/IP configuration from the router
via DHCP.
Note: Please refer to Appendix C, “Preparing Your Network” for assistance with DHCP
configuration.
3-2Connecting the Router to the Internet
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewall Router DG834G
Internet Configuration Requirements
Depending on how your ISP set up your Internet account, you need one or more of these
configuration parameters to connect your router to the Internet:
Where Do I Get the Internet Configuration Parameters?
There are several ways you can gather the required Internet connection information.
•Your ISP should have provided you with all the information needed to connect to the Internet.
If you cannot locate this information, you can ask your ISP to provide it or you can try one of
the options below.
•If you have a computer already connected using the active Internet access account, you can
gather the configuration information from that computer.
•For Windows 95/98/ME, open the Network control panel, select the TCP/IP entry for the
Ethernet adapter, and click Properties.
•For Windows 2000/XP, open the Local Area Network Connection, select the TCP/IP entry
for the Ethernet adapter, and click Properties.
•For Macintosh computers, open the TCP/IP or Network control panel.
•You can also refer to the DG834G Resource CD for the NETGEAR Router ISP Guide which
provides Internet connection information for many ISPs.
Once you locate your Internet configuration parameters, you may want to record them on the page
below according to the instructions in “Record Your Internet Connection Information” on page
3-3.
Record Your Internet Connection Information
Print the following page. Fill in the configuration parameters from your Internet Service Provider
(ISP).
Connecting the Router to the Internet3-3
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
ISP Multiplexing Method and Virtual Circuit Number: The default settings of your DG834G
54 Mbps Wireless ADSL Firewall Router will work fine for most ISPs. However , some ISPs use a
specific Multiplexing Method or a Virtual Circuit Number for either the Virtual Path Identifier
(VPI) or Virtual Channel Identifier (VCI). If your ISP provided you with a specific Multiplexing
Method or VPI/VCI number, then fill in the following:
Multiplexing Method, circle one: LLC-based or VC-based
VPI: ________
A number between 0 and 255. VCI: ___________ A number between 1 and
65535.
ISP Login Name: The login name and password are case sensitive and must be entered exactly as
given by your ISP. Some ISPs use your full e-mail address as the login name. The Service Name is
not required by all ISPs. If you use a login name and password, then fill in the following:
Login Name: ______________________________
Password: __________________________ __
Service Name: _____________________________
Fixed or Static IP Address: If you have a static IP address, record the following information. For
example, 169.254.141.148 could be a valid IP address.
Fixed or Static Internet IP Address: ______
ISP DNS Server Addresses: If you were given DNS server addresses, fill in the following:
Primary DNS Server IP Address: ______
. ______ . ______ . ______
Secondary DNS Server IP Address: ______ . ______ . ______ . ______
Host and Domain Names: Some ISPs use a specific host or domain name like CCA7324-A or
home. If you did not get host or domain names, use the following examples as a guide:
•If your main e-mail account with your ISP is aaa@yyy.com, then use aaa as your host name.
Your ISP might call this your account, user, host, computer, or system name.
•If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.
ISP Host Name: _________________________
ISP Domain Name: _______________________
For Wireless Access: For configuration of the wireless network, record the following:
Wireless Network Name (SSID): ________ ___ __ __ __ _
WEP Authentication (circle one): Automatic, Open System, or Shared Key
WEP Encryption (circle one): 64 or 128; Passphrase or Key: ____________________
3-4Connecting the Router to the Internet
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewall Router DG834G
Connecting the DG834G to Your LAN
This section provides instructions for connecting the DG834G wireless router.
Note: The Resource CD included with your router contains an animated Installation Assistant to
help you through this procedure.
How to Connect the Router
There are four steps to connecting your firewall:
1.Connect the router to your ADSL line.
2.Connect the router to the computers on your network.
3.Log in to the router.
4.Connect to the Internet.
Follow the steps below to connect your router to your network. Before you begin, locate the ADSL
configuration information from your Internet Service Provider (ISP).
1. CONNECTTHE DG834G TOTHE ADSL LINE.
a.You need to install a filter on every telephone or device that shares the same phone
number as your ADSL router. Select the filter that came with your router.
One-Line Filter
Two-Line Filter
With Splitter
Figure 3-3: ADSL microfilters
Phone
DSL
Phone
Line
Note: If you purchased the DG834G in a country where the filter is not included, you must
acquire one.
b.Two-Line Filter Example . Insert the two-line filter into the phone outlet and connect the
phone to the phone line connector (A):
Connecting the Router to the Internet3-5
Splitter
202-10006-01
Reference Manual for the 54 Mbps Wireless ADSL Firewa ll Rou ter DG8 34G
.
Line
Phone
DSL
A
Figure 3-4: Connecting an ADSL microfilter and phone
Note: To use a one-line filter with a separate splitter, insert the splitter into the phone
outlet, connect the one-line filter to the splitter, and connect the phone to the filter.
2. CONNECTTHE DG834G TOTHE INTERNET.
Note: Improperly connecting a filter to your DG834G wireless router will block your ADSL
connection.
a.Turn off your computer.
b.Connect the ADSL port of the DG834G to the ADSL port (B) of the two-line filter:
Line
Phone
DSL
B
54 Mbps Wireless ADSL
Firewall Router DG834G
Figure 3-5: Connecting the DG834G wireless router to an ADSL microfilter and phone
3-6Connecting the Router to the Internet
202-10006-01
Loading...
+ 136 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.