Netgear AXM762 Installation Manual

Installation

Installing an AXM762 Module

Technical Speciﬁcations

ProSAFE® 10 Gigabit Ethernet SFP+ Module

Model AXM762

Install Your Optical Module

The 10 Gigabit small form-factor pluggable (SFP+) module provides a fullduplex 10G bps each direction for Ethernet operation on NETGEAR managed switches.

The switch will automatically detect the AXM762, so you can simply plug it into an available module slot.

The module can be inserted or removed while the switch is operational.

Insert the module ﬁrmly into the slot that supports the SFP+ interface. Make sure the optical cable you use is single mode LC to LC duplex cable.

Removing an AXM762 Module

Release the module latch by pulling down the handle bar across the module, and pull the module out of the module slot.

Standards IEEE 802.3ae 10GBase-LR

Wavelength 1310n m

Dimensions (HxWxD) 0.46” x 0.53” x 2.19”

(11.9 mm x 13.7 mm x 55.7 mm)

Weight 19.2g

Operating Temperature 32 -158º F (0 - 70ºC)

Storage Temperature 32 -185 ºF (0 - 85ºC)

Operative relative humidity 85% @ (25ºC)

Operating Distance 2m - 10km for 9/125 um SMF

Connectors LC for 9um/125um single mode cable

Power Consumption <1.5w

MTBF 4,986,536 hr (569 years)

Safety Certiﬁcation UL 1950 CSA 22.2 No. 950

Environmental Compliance RoHS

AXM762

NETGEAR INTL LTD

Building 3, University Technology Centre Curraheen Road, Cork, Ireland

NETGEAR, Inc.

350 East Plumeria Drive San Jose, CA 95134, USA

Regulatory Compliance

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to change the product described in this document without notice. NETGEAR does not assume any liability that may accrue due to the use or application of the product(s) or circuit

layout(s) described herein.

Support

Thank you for purchasing this NETGEAR product. You can visit

www.netgear.com/support to register your product, get help, access the latest

downloads and user manuals, and join our community. We recommend that you use only ocial NETGEAR support resources.

For the current EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

Certiﬁcate of Manufacture/Importer

It is hereby certiﬁed the NETGEAR model AXM762 has been suppressed in accordance with the condition set out in MBPT|Amtsb|Vfg 243/1991 and vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with regulation may, however, be subject to certain restrictions. Please refer to the note in the operating instructions. Federal Oce for Telecommunications Approvals has been notiﬁed of the placing of this equipment on the market and has been granted the right to

test the series for compliance with regulation.

Note: This device has been tested and found to comply with limits

for a Class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a commercial installation.

Laser Safety Warning

This is a Class 1 laser product.

Warning: Because invisible laser radiation may be emitted from ap-

erture of the port when no ﬁber cable is connected, avoid exposure to laser radiation and do not stare into the open aperture.

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive.

For regulatory compliance information, visit

http://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

May 2016