NEC HT1100 Owner Manual
HT1100
Entertainment Projector
User’s Manual
English
Deutsch
Français
Italiano
Español
Svenska
IMPORTANT INFORMATION
Safety Cautions
Precautions
Please read this manual carefully before using your NEC HT1100 Projector and keep the manual handy for future reference. Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power
outlet.
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the
unit may be sufficient to cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any part inside of
the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this unit has been
provided.
The information should be read carefully to avoid problems.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance -3. GSGV:
The sound pressure level is less than 70 dB (A) according to ISO 3744
or ISO 7779.
RF Interference
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by NEC Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could void your right to
operate this equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for
help.
In UK, a BS approved power cable with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cable is not
supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product, will expose you to
lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Copyright© 2003 by NEC Viewtechnology, Ltd.
E-2
Fire and Shock Precautions
Quick
Connect
Guide
User’s
manual
1.
Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at
least 4 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver
into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified
NEC service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the
projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out
of the lens, can cause unpredictable outcome such as fire or injury
to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while
the projector is on. Doing so can lead to melting of the cap and
possibly burning your hands due to the heat emitted from the light
output.
7. The projector is designed to operate on a power supply of 100-120
or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this
requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can
cause electrical shock or fire.
• Allow a minimum of 90 seconds to elapse after turning off the projector. Then turn off the main power switch, disconnect the power
cable and allow 60 minutes to cool the projector before replacing
the lamp.
What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to
ship your HT1100 Projector.
R
E
W
O
P
S
U
T
A
Y
T
B
S
ND
A
P
T
M
S
A
N
L
O
M
R
O
F
E
R
D
3
T
S
U
J
D
A
O
T
C
N
E
A
U
L
C
A
E
D
C
R
R
A
U
C
-
O
C
S
P
R
E
T
N
E
SELECT
U
N
E
M
Projector
Lens cap
(24FT8661)
C
O
C
O
M
P
E
N
T
E
R
M
E
N
U
ASPECT
P
I
C
-
C
M
A
U
M
P
N
T
U
I
C
E
C
T
T
E
U
E
R
L
E
A
U
T
O
A
U
A
D
P
U
J
T
P
.
O
O
S
I
T
D
I
O
O
N
W
VIEWERFREEZE
N
M
3
D
A
G
R
N
E
I
F
F
O
Y
R
M
H
E
L
P
Remote control
(7N900441)
L
IG
H
T
V
I
D
E
O
P
O
M
W
P
E
U
S
R
T
V
E
I
D
R
E
.
O
C
O
M
P
O
C
N
O
E
M
N
P
T
.V
D
V
I
Batteries
Soft carrying case
(24BS7113)
String and rivet
(24C05051) (24C04531)
CAUTION
1. Do not try to touch the ventilation outlet on the front and side as it
can become heated while the projector is turned on.
2. Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
3. Do not send the soft carrying case by parcel delivery service or
cargo shipment. The projector inside the soft carrying case could be
damaged. (However, it is possible to use it as a carriercase on board.)
4. Select “High Speed” in the Fan mode if you continue to use the
projector for consecutive days. (From the menu, select [Setup] →
[Page 2] → [Fan Mode].)
5. Do not unplug the power cable from the wall outlet under any one of
the following circumstances.
Doing so can cause damage to the projector:
* While the Hour Glass icon appears.
* While the message "Please wait a moment." appears. This mes-
sage will be displayed after the projector is turned off.
* While the cooling fans are running. (The cooling fans continue to
work for 90 seconds after the projector is turned off).
6. Do not eject the PC card while its data is being accessed. Doing so
can damage your PC card data.
7. Do not hold the lens part with your fingers. Doing so could pinch
fingers or hands causing injury.
Lamp Replacement
•To replace the lamp, follow all instructions provided on page E-43.
• Be sure to replace the lamp when the message "The lamp has
reached the end of its usable life. Please replace the lamp."
appears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
Power cable
(7N080204: North America)
(7N080003: G model)
Audio cable
(7N520027)
S-Video cable
(7N520028)
For Europe only
SCART adapter
(7N520018)
E-3
RGB signal cable
(7N520012)
Composite video cable
(7N520029)
Component video cable
(RCA⳯3-to-RCA⳯3)
(7N520030)
For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
TABLE OF CONTENTS
IMPORTANT INFORMATION .......................................... E-2
Safety Cautions ........................................................................... E-2
What's in the Box? ...................................................................... E-3
INTRODUCTION.............................................................. E-5
Introduction to the Projector ....................................................... E-5
Part Names of the Projector ........................................................ E-6
Attaching the lens cap .............................................................. E-6
Top Features ............................................................................. E-7
Terminal Panel Features ............................................................ E-8
Part Names of the Remote Control ........................................... E-9
Battery Installation ............................................................... E-10
Remote Control Precautions ................................................ E-10
Operating Range .................................................................. E-10
INSTALLATION AND CONNECTIONS ......................... E-11
Setting Up the Screen and the Projector .................................... E-11
Selecting a Location ............................................................... E-11
Throw Distance and Screen Size ............................................. E-12
Making Connections .................................................................. E-13
Wiring Diagram ...................................................................... E-13
Connecting Your VCR or Laser Disc Player............................. E-14
Connecting Your DVD Player .................................................. E-15
Connecting Your PC or Macintosh Computer ......................... E-16
To connect SCART output (RGB) ............................................ E-16
When Viewing a DVI Digital Signal ......................................... E-17
Connecting the Supplied Power Cable .................................... E-17
PROJECTING AN IMAGE (BASIC OPERATION) ........ E-18
Tur ning on the Projector ............................................................ E-18
Selecting a Source ..................................................................... E-19
Adjusting the Picture Size and Position ..................................... E-19
Correcting the Horizontal and Vertical Keystone Distortion
(3D Reform) .......................................................................... E-20
Optimizing RGB Picture Automatically ....................................... E-21
Tur ning Up or Down Volume ..................................................... E-22
Tur ning off the Projector ............................................................ E-22
CONVENIENT FEATURES ........................................... E-23
Using Image Position ................................................................ E-23
Tur ning Off the Image and Sound .............................................. E-23
Freezing a Picture ...................................................................... E-23
Capturing a Picture .................................................................... E-23
Enlarging and Moving a Picture ................................................. E-24
Getting the On-line Help ............................................................ E-24
USING ON-SCREEN MENU ......................................... E-25
Using the Menus ....................................................................... E-25
Menu tree .................................................................................. E-26
Menu Elements .......................................................................... E-28
Menu Descriptions & Functions ................................................ E-29
Picture .................................................................................... E-29
Preset, Reference, Brightness, Contrast, Color, Hue,
Sharpness, Noise Reduction, Detail Settings ....................... E-29
Image [Page 1] ....................................................................... E-30
Aspect Ratio ........................................................................ E-30
Blanking, Position/Clock, Image Position, Overscan,
Signal Type, Setup Level, Video Filter .................................. E-32
Image [Page 2] ....................................................................... E-32
Entry List ............................................................................. E-32
Setup [Page 1] ........................................................................ E-33
Screen, Orientation, Lamp Mode, Screen Trigger,
Background, Language, Test Pattern ................................... E-33
Setup [Page 2] ........................................................................ E-33
Signal Select, Standby Mode, Fan Mode, Lamp Hour .......... E-33
Setting Auto Adjust .............................................................. E-34
Setup [Page 3] ........................................................................ E-34
Password (Logo), LAN Mode ............................................... E-34
Security ............................................................................... E-36
Information ............................................................................. E-37
Returning to Factory Default [Reset] ...................................... E-37
USING THE VIEWER ..................................................... E-38
Making the Most out of the Viewer Function ............................. E-38
Operating the Viewer Function from the Projector (playback) ... E-39
Changing Background Logo ...................................................... E-42
MAINTENANCE ............................................................ E-43
Replacing the Lamp ................................................................... E-43
Cleaning .................................................................................... E-44
Lens Protector ........................................................................... E-44
TROUBLESHOOTING ................................................... E-45
SPECIFICATIONS ......................................................... E-47
APPENDIX ..................................................................... E-48
Cabinet Dimensions ................................................................... E-48
Pin Assignments of D-Sub COMPUTER Input Connector .......... E-48
Compatible Input Signal List ..................................................... E-49
PC Control Codes and Cable Connection ................................... E-50
Cable Connection ....................................................................... E-50
PC Control Connector (DIN-8P) ................................................. E-50
Using Software Keyboard .......................................................... E-50
Operation Using an HTTP Browser ............................................ E-51
TravelCare Guide........................................................................ E-52
E-4
INTRODUCTION
Introduction to the Projector
This section introduces you to your new HT1100 Projector and describes
the features and controls.
Congratulations on Your Purchase of The HT1100 Projector
The HT1100 is our most sophisticated single chip DLP™ based projector for the commercial and residential entertainment user. With the
HT1100 you will enjoy projecting images up to 200" (measured diagonally) from your DVD player, VCR, satellite hookup, HDTV source, PC
or Macintosh computer (desktop or notebook) and images from your
digital camera. The HT1100 can be setup on a coffee table, tabletop,
cart, bookshelf or permanently installed*
quick connect guide and full function remote, you will be ready to immerse yourself in big screen enjoyment.
Features you’ll enjoy on the HT1100:
• Phenomenal 3500:1 contrast ratio with a variable IRIS that allows
you to fine-tune the image contrast
• 3D Reform technology for positioning the projector in off center locations in the room and still get aligned images
• NEC designed and developed SweetVision™ technology for enhanced images, more vibrant colors and blacks richer with detail
• Deinterlace function eliminates jitter or artifacts in HDTV and Video
signals
• Ability to display 16:9 and 4:3 aspect ratio sources
• HDTV, SDTV compatibility
• 3D 10-bit video decoder for expanded black levels and adaptive
gamma correction
• Digital photo viewer to display larger than life images from your digital cameras PC or compact flash card
• Easy set up and operation
• High performance long life lamp for low total operating costs
• Eco-mode lamp technology for increased lamp life and energy savings
• Uncompromising display of video and data. Improves white level, color
accuracy, dynamic range, and display of varying levels of black in an
image.
• Sealed optics for reduced maintenance and better performance in
dusty areas
• Wireless remote control operation
• Network capable with a wired card for the ability to maintain and
control your projector from your computer
• Smart security settings for password protection and PC card protection key to help prevent unauthorized use
• Multiple video mode selections depending on your source.
• Control the unit with a PC using the PC Control port.
• NEC’s exclusive Advanced AccuBlend intelligent pixel blending technology - an extremely accurate image compression technology - offers a crisp image with HTDV 1080p (1920⳯1080) resolution*
• Supports most IBM VGA, SVGA, XGA, SXGA (with Advanced
AccuBlend)*
other RGB signals within a horizontal frequency range of 24 to 100 kHz
and a vertical frequency range of 48 to 100 Hz. This includes NTSC,
PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 standard video
signals.
2
, Macintosh, component signal (YCbCr/ YPbPr) or any
1
. With an extensive input panel,
2
.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
•You can control the projector with a PC using the PC Control port
and wired LAN.
• The contemporary cabinet design is light, compact, easy to carry.
1
*
Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the pro-
jector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
2
*
HDTV 1080p (1920⳯1080), HDTV 1080i (1920⳯1080) and
HDTV 720p (1280⳯720) are displayed with NEC’s Advanced
AccuBlend.
Digital Light Processing and DLP are trademarks of Texas Instruments.
The specifications are subject to change without notice.
All other trademarks are the property of their respective owners.
All specifications subject to change without notice.
E-5
Part Names of the Projector
PC CONTROL
COMPUTER IN
DVI-D IN
SC TRIGGER
VIDEO IN
S-VIDEO IN
S
-VID
EO
S
-VID
EO RG
B/DV
I
RG
B/DV
I
V
IDEOVIDEO
AU
D
IO IN
AU
D
IO IN
C
O
M
P
O
N
E
N
T
Y
C
b/Pb Cr/Pr
Remote Sensor (See page E-10)
Focus Ring (See page E-20)
Controls (See page E-7)
R
E
W
O
P
S
U
T
Y
TA
B
S
D
N
A
P
T
S
AM
N
L
O
M
R
O
F
E
R
D
3
T
S
U
J
D
A
O
T
C
N
E
A
U
L
C
A
E
D
C
R
R
A
U
C
-
O
C
S
P
R
E
T
N
E
T
C
E
L
E
S
U
N
E
M
Ventilation (inlet)
Ventilation (outlet)
Heated air is exhausted from here
Built-in Security Slot ( )*
Zoom Lever (See page E-20)
Adjustable Tilt Foot Lever (See page E-19)
Carrying Handle
Lens
Adjustable Tilt Foot (See page E-19)
Lens Cap
Iris Lever (See page E-20)
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
PC Card Eject Button
PC Card Slot
Stereo Speaker (2W)
Lamp cover (See page E-43)
Ventilation (outlet)
Heated air is exhausted from here
Remote Sensor (See page E-10)
Lamp cover screw
Rear Foot
Rear Foot
Rotate to make the projector level. (See page E-20)
AC Input
Connect the supplied power cable's three-pin plug here, and plug the
other end into an active wall outlet. (See page E-17)
Main Power Switch
When you plug the supplied power cable into an active wall outlet and
turn on the Main Power switch, the POWER indicator turns orange and
the projector is in standby mode. (See page E-18)
Attaching the lens cap
To attach the lens cap to the bottom with the supplied string and rivet:
1. Thread the string through the
hole on the lens cap and then
tie a knot in the string.
2. Use the rivet to attach the
string to the bottom of the
projector.
E-6
Top Features
910 45 11
2
678 121 3
1. POWER Button (ON / STAND BY) ( )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode (Power-saving mode
or Idle mode).
NOTE: To turn on or off the projector, press and hold this button for a minimum of two seconds.
2. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred,
the lamp cover is not attached properly or the projector has overheated. See the Status Indicator section on page E-45 for more details.
3. POWER Indicator
When this indicator is green, the projector is on; when this indicator
is orange, it is in standby mode (Power-saving mode or Idle mode).
See the Power Indicator section on page E-45 for more details.
4. SOURCE Button
Use this button to select a video source such as a VCR, DVD player,
PC or Viewer (PC card).
Press and release this button quickly to display the Source List.
Each time this button is pressed for a minimum of ONE second the
input source will change as follows:
Video → S-Video → Component → Computer → DVI (DIGITAL) → Viewer
→ Video → ...
If no input signal is present, the input will be skipped.
5. AUTO ADJUST Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture. Some signals may not be displayed correctly or take
time to switch between sources.
NOTE: This function may not be available depending upon the input signal.
6. PC CARD Access Indicator
Lights while accessing a PC card.
7. ENTER Button
Executes your menu selection and activates items selected from the
menu.
8. CANCEL Button
Press this button to exit "Menus". Press this button to return the adjustments to the last condition while you are in the adjustment or
setting menu.
9. SELECT 왖왔왗왘 (+) (–) / Volume Buttons
왖왔 : Use these buttons to select the menu of the item you wish to
adjust.
왗왘 : Use these buttons to change the level of a selected menu item.
When no menus appear, these buttons work as a volume control, these buttons can be used to select a slide.
NOTE: When the Viewer is selected, volume control is not available.
10. MENU Button
Displays the menu.
11. LAMP Indicator
If this light blinks red rapidly, it's warning you that the projection lamp
has exceeded 2000 hours (up to 3000 hours in Eco mode) of service.
After this light appears, replace the lamp as soon as possible. (See
page E-43). If this is lit green continually, it indicates that the lamp
mode is set to Eco. See the Lamp Indicator section on page E-45 for
more details.
12. 3D REFORM Button
Press this button to enter 3D Reform mode to correct the keystone
(trapezoidal) distortion, and make the image square. This button
toggles between “Keystone” and “Cornerstone”.
E-7
Terminal Panel Features
PC CONTROL
VIDEO IN S-VIDEO IN
93511
71213
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
SC TRIGGER
COMPUTER IN
DVI-D IN
24110 86
1. COMPUTER IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player (optional adapter ADPCV1 required). This connector also supports SCART output signal.
See page E-16 for more details.
2. DVI-D IN (DVI 24 Pin)
This connector can be used to accept digital signal output from a
computer or a set top box with a DVI connector. (HDCP compatible)
3. RGB/DVI AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your computer connected to RGB IN or DVI-D IN.
4. COMPONENT (Y, Cb/Pb, Cr/Pr) input Connectors (RCA)
Connect component video outputs (Y/Cb/Cr, Y/Pb/Pr) of the external
equipment such as DVD player.
NOTE: These connectors accept component signal only.
5. COMPONENT AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your DVD player or
component equipment connected to COMPONENT IN.
6. VIDEO IN (RCA)
Connect a VCR, DVD player or laser disc player here to project video.
7. VIDEO AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your VCR, DVD player
or laser disc player connected to VIDEO IN.
8. S-VIDEO IN (Mini DIN 4 Pin)
Connect a VCR, DVD player or laser disc player with S-Video output.
NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.
9. S-VIDEO AUDIO IN Mini Jack (Stereo Mini)
This is where you connect audio output from your VCR, DVD player
or laser disc player connected to S-VIDEO IN.
10. PC CONTROL Port (Mini DIN 8 Pin)
Use this port to connect your PC to control your projector via a serial
cable. This enables you to use your PC and serial communication
protocol to control the projector. The NEC optional serial cable
(CA03D) is required to use this port. If you are writing your own program, typical PC control codes are on page E-50. A cap is put on the
port at the factory. Remove the cap when using the port.
11. SC TRIGGER Mini Jack
When the projector is powered ON the screen trigger output sends a
high voltage trigger to the screen controller and the screen will go
down.
When the projector is powered OFF the screen trigger stops sending
a low voltage trigger to the screen controller and the screen will go
up.
NOTE: To enable the SC.TRIGGER function, be sure to turn on "Screen Trigger" in "Page 1" of the Setup. See page E-33.
NOTE: Screen Controllers are supplied and supported by screen manufactures. This option is not included with the projector.
NOTE: Do not use this jack for anything other than intended use. Connecting
an audio cable or equivalent to the SC. TRIGGER Mini Jack causes damage to
this mini jack.
Stereo mini cable
(not supplied)
Tip (12V)
Ring (NC)
Sleave (ground. 0V)
12. PC CARD Eject Button
Press to eject a PC card partially.
13. PC CARD Slot
Insert a PC card or commercially available wired LAN card here.
E-8
Part Names of the Remote Control
11
13
16
17
19
20
1
3
5
4
7
9
LIGHT
VIDEO
S-VIDEO
COMPUTER
COMP. DVI
ENTER
MENU
ASPECT
PICTURE
PIC-MUTE
MUTE
FREEZE
UP
POSITION MAGNIFY
DOWN
POWER
COMPONENT
COMP.V
CANCEL
AUTO ADJ.
AUTO
VIEWER
3D REFORM
HELP
2
6
8
10
12
15
14
18
21
22
9
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
2. POWER Button
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode (Power-saving mode
or Idle mode).
To turn on or off the projector, press and hold this button for a minimum of two seconds.
3. LIGHT Button
Use this button to turn on or off the button’s backlight. Unless another
button is pressed within 10 seconds while the backlight is on, it will
turn off to conserve the batteries.
4. VIDEO Button
Press this button to select an NTSC, PAL, PAL-N, PAL-M, PAL60,
SECAM or NTSC4.43 compatible video source from a VCR, DVD
player, or laser disc player.
5. S-VIDEO Button
Press this button to select an S-Video source from a VCR, DVD player
or laser disc player.
6. COMPONENT Button
Press this button to select a video source from component equipment connected to your COMPONENT input.
7. COMPUTER Button
Press this button to select a video source from computer or component equipment connected to your COMPUTER IN port.
8. DVI Button
Press this button to select a DVI digital signal from a computer, DVD
player or settop box.
9. Select 왖왔왗왘 / Volume Button
왖왔 : Use these buttons to select the menu of the item you wish to
adjust.
왗왘 : Use these buttons to change the level of a selected menu item.
When no menus appear, these buttons work as a volume control.
NOTE: When the Viewer is selected, volume control is not available.
10. ENTER Button
Executes your menu selection and activates items selected from the
menu.
11. MENU Button
Displays the menu for various settings and adjustments.
12. CANCEL Button
Press this button to exit "Menus". Press this button to return the adjustments to the last condition while you are in the adjustment or
setting menu.
13. ASPECT Button
Press this button to display the Aspect Ratio select screen. Each
time this button is pressed, the option will be changed. See page E-
30.
14. PICTURE Button
Press this button to display the Preset window. Each time this button
is pressed, the option will be changed. See page E-29.
15. AUTO ADJ Button
Use this button to adjust an COMPUTER source for an optimal picture. Some signals may not be displayed correctly or take time to be
displayed. See page E-21.
NOTE: This function may not be available depending upon the input signal.
16. PIC-MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an image
and sound without turning off the menu.
17. FREEZE Button
This button will freeze a picture. Press again to resume motion.
18. VIEWER Button
Press this button to select the Viewer source.
19. POSITION Up/Down Button
This button adjusts position of a zoomed image. See page E-23.
20. MAGNIFY (+) (–) Button
Use this button to adjust the image size up to 400%. The image is
magnified about the center of the screen. When the image is magnified, you can move the image by using the SELECT 왖왔왗 왘 button.
See page E-24.
21. 3D REFORM Button
Press this button to enter 3D Reform to correct the keystone (trapezoidal) distortion, and make the image square. See page E-20.
22. HELP Button
Provides the online help or the set information.
E-9
Battery Installation
1. Press firmly and slide the battery cover off.
1
2
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the
batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of
batteries together.
2. Remove both old batteries and install new ones (AAA). Ensure that
you have the batteries' polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not
mix different types of batteries or new and old batteries.
Operating Range
7m/22 feet
7m/22 feet
30°
25°
30°
30°
Remote sensor on the
projector cabinet
• The infrared signal operates by line-of-sight up to a distance of about
22 feet / 7 m and within a 55°(Front) / 60°(Rear) angle of the remote
sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor.
Weak batteries will also prevent the remote control from properly
operating the projector.
Remote control
E-10
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
Set up a screen and the projector.
z
x
Connect your video equipment to the projector. See page E-13 – 17.
c
Connect the supplied power cable. See page E-17.
NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. When
moving the projector or when it is not in use, cover the lens with the lens cap.
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the
image can be is approximately 30" (0.8 m) measured diagonally when the projector is roughly 4 feet
(1.0 m) from the wall or screen. The largest the image can be is 200" (5.08 m) when the projector is
about 23 feet (7 m) from the wall or screen. Use the drawing below as a guide.
Screen size (Unit: cm/inch)
406.4(W) X 304.8(H)/160"(W) X 120"(H)
365.8(W) X 274.3(H)/144"(W) X 108"(H)
304.8(W) X 228.6(H)/120"(W) X 90"(H)
243.8(W) X 182.9(H)/96"(W) X 72"(H)
203.2(W) X 152.4(H)/80"(W) X 60"(H)
162.6(W) X 121.9(H)/64"(W) X 48"(H)
121.9(W) X 91.4(H)/48"(W) X 36"(H)
81.3(W) X 61.0(H)/32"(W) X 24"(H)
61.0(W) X 45.7(H)/24"(W) X 18"(H)
Lens center
30"
40"
1.0/3.3
60"
100"
80"
1.3/4.3
120"
2.0/6.6
150"
180"
2.7/8.9
200"
3.4/11.2
Screen size
4.1/13.5
6.2/20.34
5.2/17.1
Distance (Unit: m/feet)
6.9/22.6
NOTE: The above shows the throw distance for 4:3 screen.
E-11
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
Distance Chart
Screen Height
Screen Width
Screen Diagonal
Screen center
(B)
Screen Bottom
(D)
Lens Center
Throw Angle (움)
Throw Distance (C)
B=Ver tical distance between lens center and screen center
C=Throw distance
D=Ver tical distance between lens center and bottom of screen
α = Throw angle
4:3
3.6
4.8
6.0
7.2
9.6
α
Wide – Tele
degree
19.3 – 16.1
19.1 – 16.0
19.0 – 15.9
18.9 – 15.8
18.9 – 15.8
18.8 – 15.7
18.8 – 15.7
18.7 – 15.7
18.7 – 15.7
18.7 – 15.7
Screen Size B C
Diagonal Width Height
inch
100
120
150
180
200
inch
inch
30
40
50
60
80
120
144
160
18
24
32
24
40
30
36
48
64
48
80
60
72
96
90
108
120
inch
12.6
16.8
21.0
25.2
33.6
42.0
50.4
63.0
75.6
84.0
Wide – Tele
inch
35.7 – 43.4
48.2 – 58.4
60.7 – 73.5
73.2 – 88.5
98.1 – 118.6
123.1 – 148.6
148.1 – 178.7
185.5 – 223.8
223.0 – 268.9
248.0 – 298.9
inch
12.0
14.4
18.0
21.6
24.0
D
NOTE: A 16:9 image is supported within the limits of the above values.
WARNING
* Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector severely damaged.
• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41˚F (5˚C) and 95˚F
(35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will
harm the screen image.
• Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the side or the front of
the projector.
NOTE: Distances may vary +/–5%.
Screen Size B C
Diagonal Width Height
mm
762.0
1016.0
1270.0
1016.0
1524.0
1219.2
2032.0
1625.6
2540.0
2032.0
3048.0
2438.4
3810.0
3048.0
4572.0
3657.6
5080.0
4064.0
mm
609.6
812.8
mm
457.2
609.6
762.0
914.4
1219.2
1524.0
1828.8
2286.0
2743.2
3048.0
mm
319.8
426.5
533.3
640.0
853.4
1066.9
1280.4
1600.6
1920.8
2134.3
Wide – Tele
mm
907 – 1102
1224 – 1484
1541 – 1866
1858 – 2248
2493 – 3011
3127 – 3775
3761 – 4539
4713 – 5684
5664 – 6829
6298 – 7593
D
mm
91.2
121.7
152.3
182.8
243.8
304.9
366.0
457.6
549.2
610.3
Wide – Tele
19.3 – 16.1
19.1 – 16.0
19.0 – 15.9
18.9 – 15.8
18.9 – 15.8
18.8 – 15.7
18.8 – 15.7
18.7 – 15.7
18.7 – 15.7
18.7 – 15.7
Reflecting the Image
Using a mirror to reflect your projector's image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
you're using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or 왖왔 buttons on your remote control to correct the orientation. (See page E-33.)
α
degree
E-12
Making Connections
Wiring Diagram
Video Game
PC CONTROL
Component video cable
⳯
3)
(RCA
(Supplied)
VIDEO IN S-VIDEO IN
VCR, DVD Player or
LaserDisc Player
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
To video, S-video,
and audio inputs
on the projector.
SC TRIGGER
COMPUTER IN
Set top box
DVI-D IN
RGB Signal cable (supplied)
To mini D-Sub 15-pin connector on
the projector. It is recommended
that you use a commercially available distribution amplifier if connecting a signal cable longer than
the supplied cable.
DVD Player
(with component output)
Macintosh
(Desktop type or notebook type)
IBM VGA or Compatibles
(Desktop type or notebook type)
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.
E-13
Connecting Your VCR or Laser Disc Player
VIDEO AUDIO IN
or
S-VIDEO AUDIO IN
Composite video
VIDEO IN
PC CONTROL
S-VIDEO IN
VIDEO IN S-VIDEO IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
SC TRIGGER
Y Cb/Pb Cr/Pr
DVI-D IN
COMPUTER IN
S-video cable (supplied)
cable (supplied)
Audio equipment
Audio cable
(supplied)
AUDIO IN
LR
VCR/ Laser disc player
AUDIO OUT
RL
S-VIDEO OUT
VIDEO OUT
Audio cable (not supplied)
Use the supplied composite video cable to connect your VCR or laser disc player to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR or laser disc player.
2. Connect one end of the composite video cable to the video output connector on the back of your VCR or laser disc player, connect the other end
to the Video input on your projector. Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio
equipment (if your VCR or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo
sound.
3. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements.
E-14
Connecting Your DVD Player
COMPONENT
AUDIO IN
COMPONENT IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
SC TRIGGER
DVI-D IN
COMPUTER IN
VIDEO IN S-VIDEO IN
PC CONTROL
Audio cable
(supplied)
Component video RCA
(supplied)
⳯
3 cable
Audio Equipment
AUDIO IN
LR
DVD player
AUDIO OUT
RL
COMPONENT OUT
Audio cable (not supplied)
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use the supplied component video cable (RCA
the COMPONENT IN connectors on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a composite VIDEO output of
the DVD player to the Video Input of the projector.
Use an audio cable (not supplied) to connect the audio from your VCR or laser disc player to your audio equipment (if your VCR or laser disc
player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.
3. Turn on the projector and DVD player.
⳯
3) to connect your DVD player to
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements,
E-15
Connecting Your PC or Macintosh Computer
PC CONTROL
COMPUTER IN
DVI-D IN
SG TRIGGER
VIDEO IN S-VIDEO IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
Y Cb/Pb Cr/Pr
PHONE
AUDIO IN
PHONE
COMPUTER
Audio cable (not supplied)
NOTE: For older Macintosh, use
a commercially available pin
adapter (not supplied) to connect to your Mac's video port.
IBM VGA or Compatibles (Desktop type)
or Macintosh (Desktop type)
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recommended
that you use a commercially available distribution amplifier if connecting a signal cable longer than the supplied one.
IBM VGA or Compatibles (Notebook type)
or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the
projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer you've connected to the
projector.
For European model only
To connect SCART output (RGB)
Before connections: The supplied SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE: Audio signal is not available for this connection.
Video equipment
such as DVD player
Projector
R
E
W
O
P
S
U
T
A
T
BY
S
P
M
STAND
A
L
ON
ALIGNMENT
O ADJUST
AUT
SOURCE
U
N
C
N
E
A
L
C
D
R
A
C
C
P
R
E
T
N
E
T
C
E
L
E
S
E
M
NOTE: The HT1100 is not compatible with video decoded outputs of NEC ISS6020 and ISS-6010.
NOTE: An image may not be displayed correctly when a Video or S-Video source
is played back via a commercially available scan converter.
This is because the projector will process a video signal as a computer signal at
the default setting. In that case, do the following.
* When noise appears on the sides of the screen:
Use the Overscan feature to display the image correctly.
Be sure to change the Overscan to 0% before pressing the AUTO ADJ or
AUTO ADJUST button. Unless otherwise an image may be displayed with its
sides cut off.
1. Turn off the power to the projector and your video equipment.
2. Use the supplied SCART adapter and a commercially available
SCART cable to connect the COMPUTER input of your projector and
a SCART output (COMPUTER) of your video equipment.
3. Turn on the power to the projector and your video equipment.
4. Use the COMPUTER button on the remote control to select the COMPUTER input.
5. Press the MENU button on the remote control to display the menu.
6. From the Advanced menu, select [Setup]
→
[Page 2] → [Signal Select] → [Computer] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs
and DVD players. It is also referred to as Euro-connector.
Commercially available
SCART cable
To COMPUTER IN
SCART adapter
ADP-SC1 (supplied)
E-16
PC CONTROL
COMPUTER IN
DVI-D IN
SC TRIGGER
VIDEO IN
S-VIDEO IN
S-VIDEOS-VIDEO
RGB/DVIRGB/DVI
VIDEOVIDEO
AUDIO INAUDIO IN
COMPONENT
Y
Cb/Pb
Cr/Pr
When Viewing a DVI Digital Signal:
PC CONTROL
Audio cable (not supplied)
PHONE
AUDIO IN
S-VIDEOS-VIDEO RGB/DVIRGB/DVIVIDEOVIDEO AUDIO INAUDIO IN
COMPONENT
VIDEO IN S-VIDEO IN
Y Cb/Pb Cr/Pr
SC TRIGGER
COMPUTER IN
DVI-D IN
DVI-D IN
DVI-D Signal cable (not supplied)
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC
or projector. Turn on the projector first and select DVI (DIGITAL) from
the source menu before turning on your PC.
Failure to do so may not activate the digital output of the graphics card
resulting in no picture being displayed. Should this happen, restart your PC.
Do not disconnect the DVI-D signal cable while the projector is running. If
the signal cable has been disconnected and then re-connected, an image may not be correctly displayed. Should this happen, restar t your PC.
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's three-pin plug to the AC IN of
the projector, and then connect the other plug of the supplied power
cable in the wall outlet.
NOTE:
• Use the DVI-D cable compliant with DDWG (Digital Display Working Group)
DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should
be within 5 m (196") long.
• See page E-49 for DVI digital signals the DVI (DIGITAL) connector supports.
E-17
Loading...