NEC 65” InfinityBoard 2.0, 75” InfinityBoard 2.0, 86 InfinityBoard 2.0, 65” InfinityBoard 2.1, 75” InfinityBoard 2.1 operation manual

...

User’s Manual

All-in-one Collaboration Solution

NEC 65” InfinityBoard 2.0 / 2.1

NEC 75” InfinityBoard 2.0 / 2.1 NEC 86” InfinityBoard 2.0 / 2.1

MONITOR MODEL: V654Q IGB, V754Q IGB, V864Q IGB

Please find your model name on the label on rear side of the monitor.

Index

Addendum to User’s Manuals of MultiSync V654Q, V754Q, V864Q……..……………… Page 03

Registration Information……………………………………………………………………….. Page 04

Important Information………………………………………………………………………….. Page 06

Safety Precautions, Maintenance & Recommended Use…………………………………. Page 07

Shipping Content………………………………………………………………………………..Page 08

Unpacking………………………………………………………………………………………. Page 09

General Installation…………………………………………………………………………….. Page 10

InfinityBoard Assembly Instruction…………………………………………………………….Page 11

Setup the OPS Slot-in PC…………………………………………………………………….. Page 17

Troubleshooting………………………………………………………………………………….Page 19

Specifications – 65” InfinityBoard 2.0 / 2.1……………………………………………………Page 21

Specifications – 75” InfinityBoard 2.0 / 2.1……………………………………………………Page 25

Specifications – 86” InfinityBoard 2.0 / 2.1……………………………………………………Page 30

Manufacturer’s Recycling and Energy Information…………………………………………. Page 33

Addendum to User’s Manuals of MultiSync V654Q, V754Q, V864Q

This user’s manual is an addendum to the standard user’s manual of the base model monitors V654Q,

V754Q and V864Q.

All specifications listed here supersede those in the standard version of the manual included with this monitor.

NOTE: Following feature sets are not supported by the InfinityBoard models:

- Table Top Stand Option: Other than the standard monitor, the NEC InfinityBoard does not allow for table top installations, as the table top brackets has been removed

- Room Light Sensing Sensor: Other than the standard monitor, the NEC InfinityBoard does not allow the monitor to make automatic adjustments to the backlight setting.

- Intelligent Wireless Data Sensor: Other than the standard monitor, the NEC InfinityBoard does not include a sensor for wireless communication to the monitor for information and settings.

- NEC ornament logo: Other than the standard monitor, the NEC InfinityBoard does not have an ornament logo. Therefore changing the position of the NEC logo is not possible.

Registration Information

Cable Information

CAUTION: Use the provided specified cables with this product so as not to interfere with radio and

television reception. For USB please use a shielded signal cable with ferrite core. For HDMI, DisplayPort and D-Sub 9-pin, please use a shielded signal cable. For Audio, please use a signal cable with ferrite core. Use of other cables and adapters may cause interference with radio and television reception.

FCC Information

WARNING: The Federal Communications Commission does not allow any modifications or

changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address: 3250 Lacey Rd, Ste 500

Downers Grove, IL 60515

Tel. No.: (630) 467-3000

Type of Product: Display Monitor

Equipment Classification: Class B Peripheral

Model: V654Q IGB / V754Q IGB / V864Q IGB

Registration Information

DECLARATION OF CONFORMITY

Windows is a registered trademark of Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

MultiSync is a trademark or registered trademark of NEC Display Solutions, Ltd. in Japan and other countries.

DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video Electronics Standards Association in the United States and other countries.

All other brands and product names are trademarks or registered trademarks of their respective owners.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

microSD and microSD SDHC logos are trademarks of SD-3C, LLC.

CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other countries.

Raspberry Pi is a trademark of the Raspberry Pi Foundation.

Adobe and the Adobe logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

GPL/LGPL Software Licenses

The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL), and others. For more

information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on

the supplied CD-ROM.

Important Information

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not supplied with this equipment, please contact NEC. For all other cases, please use the power cord with the plug style that matches the power socket where the monitor is located. The compatible power cord corresponds to the AC voltage of the power outlet and has been approved by, and complies with, the safety standards in the country of purchase.

This equipment is designed to be used with a power cord that has a protective earth pin connected to earth. If the power cord is not connected to the earth, it may cause electric shock. Please make sure the power cord is earthed properly.

* When operating this monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used.

NOTE: This product can only be serviced in the country where it was purchased.

Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.

• The intended primary use of this product is as an Information Technical Equipment in an office or domestic

environment.

• The product is intended to be connected to a computer and is not intended for the display of television

broadcast signals.

Safety Precautions, Maintenance & Recommended Use

Safety Precautions and Maintenance

Refer to the instruction explained on page English-3 of the standard user’s manual of the monitor.

Cleaning the Glass Surface

• The glass surface should be cleaned regularly with a soft, lint free cloth.

• It is recommended to use an anti-static plastic and glass cleaner suited for PMMA/acrylic

glass/Plexiglas, or water with a small amount of washing-up liquid.

Cleaning the Cabinet

• Unplug the power supply.

• Gently wipe the cabinet with a soft cloth.

• To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and

follow with a dry cloth.

NOTE: DO NOT clean with benzene thinner, alkaline detergent, alcoholic system detergent, wax, polish cleaner, soap powder or insecticide. Rubber or vinyl should not be in contact with the cabinet for an extended period of time. These types of fluids and materials can cause paint to deteriorate, crack or peel.

Shipping Content

65” / 75” / 86” InfinityBoard 2.0

1. FlatFrog InGlass™ Touch Display – V654Q IGB / V754Q IGB / V864Q IGB

2. OPS Slot-in PC - OPS-Kbl-i7v-d8/128/W10Pro/W/TPM/Infinity

3. Side-mounted Speaker Set – SP-65IB SM / SP-75IB SM / SP-86IB SM

4. USB Camera - Huddly GO 2m Room Kit

5. 2x Passive Magnetic Pen

6. Remote Control

7. CD-ROM (User Guides/Manuals)

8. Addendum to User’s Manuals

9. Power Cable

10. DisplayPort Cable

11. 2x USB Cable 300 cm

12. USB Cable 10 cm

13. Cable Clamps

65” / 75” / 86” InfinityBoard 2.1

1. FlatFrog InGlass™ Touch Display – V654Q IGB / V754Q IGB / V864Q IGB

2. OPS Slot-in PC - OPS-Kbl-i7v-d8/128/W10Pro/W/TPM/Infinity

3. Side-mounted Speaker Set – SP-65IB SM / SP-75IB SM / SP-86IB SM

4. USB Camera - Huddly IQ 2m Room Kit

5. 2x Passive Magnetic Pen

6. Remote Control

7. CD-ROM (User Guides/Manuals)

8. Addendum to User’s Manuals

9. Power Cable

10. DisplayPort Cable

11. 2x USB Cable 300 cm

12. USB Cable 10 cm

13. Cable Clamps

Unpacking

Unpacking the Display

Unpack the display (V654Q IGB / V754Q IGB / V864Q IGB) from the carton box by removing the white clips on the bottom of the box.

NOTE: Due to the weight of the product, for installation and handling 4 people are required. DO NOT start unless you have enough people available. Working with less people may result in injuries and damaged product.

Lift the carton box upwards. Make sure to have one additional person to secure the display from tipping over.

NOTE: Remember to save your original box and packing material to transport or ship the monitor.

For further instructions, please refer to the printed instruction on the carton box.

General Installation

This device cannot be used or installed without a mounting accessory for support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty

Mounting

For customer:

CAUTION

DO NOT mount the monitor yourself. For proper installation it is strongly recommended to use a trained, qualified technician. Please contact your supplier, as they may be able to provide a list of qualified installation professionals. Mounting on a wall or ceiling and hiring a technician is the customer’s responsibility.

Maintenance

• Periodically check for looses screws, gaps, distortions, or other problems that may occur with the

mounting equipment. If a problem is detected, please refer to qualified personnel for service.

• Regularly check the mounting location for signs of damage or weakness that may occur over time.

DO NOT block ventilated openings with mounting accessories or other accessories.

For NEC Qualified Personnel:

Stability Hazard.

The device may fall, causing serious personal injury or death. To prevent injury, this device must be securely attached to the floor/wall in accordance with the installation instructions. Carefully inspect the location where the unit is to be mounted. Not all walls or ceilings are capable of supporting the weight of the unit. Weight of this monitor is mentioned in Specification (see 65” InfinityBoard 2.0 on page 21, 75” InfinityBoard 2.0 on page 25, 86” InfinityBoard 2.0 on page 30). Product warranty does not cover damage caused by improper installation, remodeling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty.

To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location.

NOTE: To achieve optimum performance of touch technology, monitor must be correctly leveled. Only straight upright and titled back position of the monitor is acceptable. Monitor tilted to front will result in convex position of the glass and might negatively influence the touch performance.

For further instructions, please refer to standard user’s manual of the base model monitors V654Q, V754Q and V864Q.

Convex position of glass

InfinityBoard Assembly Instruction

Mounting of Speakers & Camera

PART QUANTITY DESCRIPTION

A 1 Display

B 2 Speaker

C 1 Camera

D 1 1/4“ x 16 Screw

E 1 Washer

F 12 M4 x 12 Countersunk Screw

G 6 Speaker Bracket

H 12 3.5 x 6 Screw

I 2 Back Plate

J 4 M4 x 12 Screw

K 4 Washer

L 1 Mounting Bracket

M 1 USB 3.0 Angled Cable (2m)

NOTE: Do not torque screw D (picture 2) too tight. That way you will still be able to mechanically adjust the position of the camera after the installation.

Connect the 2 m USB cable supplied with the Huddly camera to USB-C on the camera. Guide the camera cable gently through the long opening in the back plate of the speaker (picture 3).

+ 23 hidden pages