Navman A300 settings Manual

Download

A300

Setting options

NAVMAN

Press and hold

to enter setup

Press

repeatedly to step through the setting options.

Press both buttons together (

) to start or stop editing

a setting option.

While editing, press

repeatedly to step through selectable states,

or increase/decrease values. Press and hold the appropriate button

increase/decrease values quickly

Set (12hr)

lets you set 12hr or 24hr time format

Set (31-12)

lets you set dd-mm or mm-dd date format

Calc up

When ‘calc up’ is «ON» the A300 calculates data for all movement (uphill and downhill). When ‘calc up’ is «OFF» the A300 calculates information for downhill movement only.

Beep

When beep is «ON» a beep will sound when the buttons are pushed.

Set units (km/h)

lets you set speed units to «km/h» or «mph»

Distance and altitude are displayed in units corresponding to the speed units, i.e. if you choose «km/h» for speed units, then distance is displayed in «km» and altitude in «m».

Set offset

lets you adjust the A300 to display local time

The date is displayed to ensure that time adjustments are made in the correct direction, i.e. both correct time and correct date should be displayed. GPS signals must be obtained to set local time.

Press and hold

to leave setup

A300 — Settings

A300

KEY = press this button = press this button = press both buttons together

Use the settings

NAVMAN

settings editing details

edit

A300 — Settings

beep

beep ON

beep OFF

set units (km/h)

set units (mph)

set units (km/h)

set offset

set 12hr

set 31-12

set 24hr

set 12-31

set units (km/h)

set (12hr) set (12hr)

set (31-12)set (31-12)

time (date)

Calc up

Calc up ON

Calc up OFF

Calc up

�

edit

A300

Normal operating modes

Press

to start normal operation

Press

repeatedly to step through the modes (hold

cycle automatically through modes).

Speed

shows session distance and current speed

Speed (AVG)

shows session distance and average speed

Speed (MAX)

shows session distance and maximum speed

Odometer

shows total distance

Altitude

shows total accumulated altitude and current altitude

Clock

shows the current time and date

(You may need to adjust the settings to display your local time)

Timer

shows session and lap times

The timer starts automatically whenever you start moving and stops whenever you stop moving.

Timer Recall

lets you recall stored lap data. Repeatedly pressing

recalls

lap data starting from the last stored lap, then lap 1, 2, 3 etc.

Press and hold

to shut down the A300

NAVMAN

A300 — Modes

A300

Use the modes

Speed (AVG)

Speed (MAX)

Speed

modes

operating details

KEY = press this button = press this button = press both buttons together = press and hold both buttons together

Clock

Timer

Odometer

clear all* session data

Timer recall

Altitude

store current lap data

clear all* session data

store current lap data

clear max speed only

store current lap data

clear odometer only

store current lap data

clear accumulated altitude only

store current lap data

clear all* session data

store current lap data

clear all* session data

store current lap data

restart recall from lap 1

recall lap data

NAVMAN

A300 — Modes

(*Does not clear odometer)

AVG

MAX

RCL

837

A300

QUICK START GUIDE

A300

NOW YOU KNOW.

A300

Be outdoors

The A300 is not intended for operation indoors or under water as it uses Global Positioning System (GPS) satellites to get time and date information, and to calculate distance and speed. For best results, always use the A300 outdoors with an unobstructed view of the sky.

1. Turn D-ring anti-clockwise and slide enclosure cover down to open battery enclosure.

2. Insert battery with «» end as indicated inside enclosure.

3. Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal.

Get ready

Step 1

Fit the battery

Fit the A300

The A300 is designed to be worn on the left upper arm. You may wish to adjust some of the settings prior to ﬁtting.

For best performance:

General use =

Alkaline

Below 5

C = NiMH

A300

The control buttons,

and

(as shown above) are pressed separately or together to turn the unit «ON» and «OFF», cycle through modes, and select mode options.

Know the buttons

Get set

Step 2

Always enter setup ﬁrst if you wish to change settings. To enter setup after starting normal operation, you must shut down and re-start the A300.

Flashing icon = seeking GPS signals Constant icon = GPS signals obtained

Startup could take up to 80 seconds to get all satellite data.

If you release

before the counter reaches zero, the A300

will immediately start normal operation.

For details about system settings see over page or consult User Guide.

Press and hold

to leave setup

counter

After leaving setup, the A300 automatically starts normal operation displaying the speed mode ﬁrst.

Enter setup

Press and hold

to enter setup

Know the startup options

1. enter setup

2. start normal operation

A300

Start normal operation

Press

to start normal operation

When starting directly into normal operation A300 will start in the mode it was in at last shutdown.

The A300 automatically operates whenever you are moving and pauses operation while you are stationary. Modes are accessed in the following order:

Step 3

Mode icons appear in the lower section of the screen. While in Speed mode you can monitor session distance and current speed. You can also store laps and clear session data.

While in Speed mode

Press

to store lap data

Press and hold

to clear all* session data

Press

to go to next mode

(*Does not clear odometer)

When you want to shut down the A300

Press and hold

Now you know

speed mode icon

session distance

current speed

For details about modes see over page or consult User Guide.

Mode example (speed)

837

Speed

Speed AVG

Speed MAX Odometer

AltitudeClockTimer

Timer RCL

RCL

MAX

AVG

Navman A300 settings Manual

Specifications and Main Features

Frequently Asked Questions

User Manual