MSI MS-7058 User Manual

i

MS-7058 (v1.X) ATX Mainboard

SYSFAN1

CPUFAN1

Intel

915P

JPW1

SATA2

SATA1

SATA4

SATA3

JCD1

T:
M:
B:

Line-In

Line-Out
Mic

T:RS -O ut
M:CS
B:SPDI F Out

-Out

Winbond

W83627THF

ICH6

BATT

+

DIMM 1

DIMM 2

PCI 3

PCI 2

PCI 1

PCI_E3

PCI_E2

PCI_E1

IDE1

FDD1

JFP1

JBAT1

JFP2JAUD1

JLPC1

JUSB1

JUSB2

USB port

ATX 1

BIOS

T: LA N ja ck
B: USB ports

COM Port

CMI

9880L

J1394_2

ii

Manual Rev: 1.0
Release Date: May 2004

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.

VOIR LA NOTICE D’INST ALLATION A V ANT DE RACCORDER AU RESEAU.

Micro-S tar International
MS-7058

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation

iii

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. We take every care in the preparation of this document, but no

guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks are the properties of their respective owners.
AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered trade-

marks of AMD Corporation.
Intel

®

and Pentium® are registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Microsoft is a registered trademark of Microsoft Corporation. Windows® 98/2000/NT/
XP are registered trademarks of Microsoft Corporation.
NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade­marks of NVIDIA Corporation in the United States and/or other countries.
Netware® is a registered trademark of Novell, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc.
Kensington and MicroSaver are registered trademarks of the Kensington Technology
Group.
PCMCIA and CardBus are registered trademarks of the Personal Computer Memory
Card International Association.

Revision History

Revision Revision History Date

V1.0 First release for PCB 1.X July 2004

with Intel 915P & ICH6

iv

1. Always read the safety instructions carefully.

2. Keep this User’s Manual for future reference.

3. Keep this equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. The openings on the enclosure are for air convection hence protects the equip-

ment from overheating. Do not cover the openings.

6. Make sure the voltage of the power source and adjust properly 110/220V be-

fore connecting the equipment to the power inlet.

7. Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

8. Always Unplug the Power Cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage or cause electrical

shock.

11. If any of the following situations arises, get the equipment checked by a service

personnel:

h The power cord or plug is damaged.
h Liquid has penetrated into the equipment.
h The equipment has been exposed to moisture.
h The equipment has not work well or you can not get it work according to

User’s Manual.

h The equipment has dropped and damaged.
h The equipment has obvious sign of breakage.

12. Do not leave this equipment in an environment unconditioned, storage

temperature above 60

0

C (1400F), it may damage the equipment.

Safety Instructions

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the
manufacturer.

v

CONTENTS

FCC-B Radio Frequency Interference Statement ....................................................... iii

Copyright Notice ........................................................................................................... iii

Revision History............................................................................................................ iii

Safety Instructions ...................................................................................................... iv

Technical Support ........................................................................................................ iv

Chapter 1. Getting Started ...................................................................................1-1

Mainboard Specifications ...................................................................................1-3

Mainboard Layout ................................................................................................ 1-4

Chapter 2. Hardware Setup ................................................................................. 2-1

Quick Components Guide....................................................................................2-2

Central Processing Unit: CPU.............................................................................. 2-3

Introduction to LGA 775 CPU ..................................................................... 2-3

CPU & Cooler Installation............................................................................2-4

Memory ................................................................................................................2-7

Introduction to DDR2 SDRAM..................................................................... 2-7

Memory Module Population Rules ..............................................................2-8

Installing DDR2 Modules ............................................................................. 2-8

Power Supply .......................................................................................................2-9

ATX 24-Pin Power Connector: ATX1 ......................................................... 2-9

ATX 12V Power Connector: JPW1............................................................2-9

Back Panel .......................................................................................................... 2-10

Mouse/Keyboard Connector ....................................................................2-10

VGA Connector (Optional) ....................................................................... 2-10

Serial Port Connector ............................................................................... 2-11

USB Connectors ....................................................................................... 2-11

LAN (RJ-45) Jack ..................................................................................... 2-12

Audio Port Connectors.............................................................................2-12

Parallel Port Connector: LPT1 .................................................................. 2-13

Connectors ......................................................................................................... 2-14

Floppy Disk Drive Connector: FDD1 ........................................................ 2-14

Fan Power Connectors: CPUFAN2/SYSF AN1/NBF AN1/PWRF AN1.......2-14

Hard Disk Connectors: IDE1, IDE2 & IDE3

(IDE 2 & IDE3 are optional) .............................................................2-15

Serial ATA/Serial ATA RAID Connectors controlled by

Intel ICH6R: SATA1~SATA4 ........................................................... 2-16

vi

CD-In Connector: JCD1 ............................................................................2-17

Front Panel Connectors: JFP1, JFP2 ....................................................... 2-17

IEEE 1394 Connectors: J1394_1, J1394_2, J1394_3 (Optional) ...........2-18

Front Panel Audio Connector: JAUD2 .....................................................2-18

IrDA Infrared Module Header: JIR1 ..........................................................2-19

Front USB Connectors: JUSB1 & JUSB2 ................................................2-19

Chassis Intrusion Switch Connector: JCI1 .............................................2-20

D-Bracket™ 2 Connector: JDB1..............................................................2-20

Jumpers .............................................................................................................2-21

Clear CMOS Jumper: JBAT1 .................................................................... 2-21

Slots ...................................................................................................................2-22

PCI Express Slots .....................................................................................2-22

PCI (Peripheral Component Interconnect) Slots......................................2-22

PCI Interrupt Request Routing ..................................................................2-23

Chapter 3. BIOS Setup ........................................................................................... 3-1

Entering Setup ..................................................................................................... 3-3

Selecting the First Boot Device ................................................................. 3-2

Control Keys ............................................................................................... 3-3

Getting Help ................................................................................................ 3-3

Main Menu ................................................................................................... 3-3

Default Settings ..........................................................................................3-3

The Main Menu.....................................................................................................3-4

Standard CMOS Features ................................................................................... 3-6

Advanced BIOS Features ................................................................................... 3-8

Advanced Chipset Features .............................................................................3-10

Integrated Peripherals ....................................................................................... 3-11

Power Management Features .......................................................................... 3-14

PNP/PCI Configurations ..................................................................................... 3-17

H/W Monitor ....................................................................................................... 3-19

Cell Menu............................................................................................................3-21

BIOS Setting Password ....................................................................................3-25

Load Fail-Safe/Optimized Defaults...................................................................3-26

Chapter 4. Introduction to CMI9880L Audio Codec ....................................... 4-1

Software Configuration ...................................................................................... 4-2

Main Setting ................................................................................................ 4-2

Smart Jack .................................................................................................. 4-6

Effect ..........................................................................................................4-8

Information .................................................................................................. 4-8

vii

1-1

Getting Started

Chapter 1. Getting
Started

Thank you for choosing the MS-7058 v1.X ATX mainboard.
The MS-7058 v1.X ATX is based on Intel® 915P and Intel® ICH6
chipset for optimal system efficiency. Designed to fit the advanced
Intel® Pentium Prescott LGA775 processor, the MS-7058 v1.X
ATX delivers a high performance and professional desktop platform
solution.

Getting Started

1-2

7058 ATX Mainboard

Mainboard Specifications

CPU

h Supports Intel® Pentium 4 Prescott LGA775 processors in LGA775 package.
h Supports up to Pentium 4 3XX, 5XX & 7XX sequence processor or higher speed.
h Supports Intel Hyper-Threading Technology.

Chipset

h Intel

®

915P chipset

- Supports FSB 533/800MHz.

- Supports PCI Express x16 interface.

h Intel

®

ICH6 chipset

- Hi-Speed USB (USB2.0) controller, 480Mb/sec, up to 8 ports.

- 4 Serial ATA ports with transfer rate up to 1.5Gb/s.

- 1 channel Ultra ATA 100 bus Master IDE controller.

- PCI Master v2.3, I/O APIC.

- ACPI 2.0 Compliant.

Main Memory

h Supports two DDR1 SDRAM
h Supports up to 2GB memory size.
h Supports Dual channel DDR1 memory architecture.

Slots

h One PCI Express x16 slot (supports PCI Express Bus specification v1.0a compliant).
h Two PCI Express x1 slots (supports PCI Express Bus specification v1.0a compliant).
h Three 32-bit v2.3 Master PCI bus slots (support 3.3v/5v PCI bus interface).

On-Board IDE

h One Ultra DMA 66/100 IDE controllers integrated in ICH6.

- Supports PIO, Bus Master operation modes.

- Can connect up to Two Ultra ATA drives.

h Serial ATA 150 controller integrated in ICH6.

- Up to 150MB/sec transfer speed.

- Can connect up to four Serial ATA devices.

On-Board Peripherals

h On-Board Peripherals include:

- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes

- 1 serial port

- 1 Line-In / Line-Out / MIC-In / Rear Speaker Out / Center-Subwoofer Speaker
Out / SPDIF-Out optical and coaxial audio port

- 8 USB ports (Rear * 4/ Front * 4)

- 1 RJ-45 LAN jack

1-3

Getting Started

LAN

h Realtek® 8100C

- Integrated Fast Ethernet MAC and PHY in one chip.

- Supports 10Mb/s, 100Mb/s.

- Compliance with PCI 2.2.

- Supports ACPI Power Management.

Audio

h Azalia link controller integrated in Intel

®

ICH6 chipset.

h 8-channel audio codec CMedia CMI9880L.

- Compliance with Azalia 1.X Spec.

- Supports Multi-Streaming function.

- Supports Universal Audio Jack (only Front Audio Jack).

BIOS

h The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral

devices and expansion cards of the board automatically.

h The mainboard provides a Desktop Management Interface (DMI) function which

records your mainboard specifications.

Mounting and Dimension

h ATX Form Factor: 24.4 cm (W) x 30.5 cm (L)
h 9 mounting holes

1-4

7058 ATX Mainboard

Mainboard Layout

MS-7058 v1.X ATX Mainboard

SYSFAN1

CPUFAN1

Intel

915P/G

JPW1

SATA2

SATA1

SATA4

SATA3

JCD1

T:
M:
B:

Line-In

Line-Out
Mic

T:R S-O u t
M:CS
B:SPDIF Out

-Out

Winbond

W83627THF

ICH6/

ICH6R

BATT

+

DIMM 1

DIMM 2

PCI 3

PCI 2

PCI 1

PCI_E3

PCI_E2

PCI_E1

IDE1

FDD1

JFP1

JBAT1

JFP2JAUD1

JLPC1

JUSB1

JUSB2

USB port

ATX 1

BIOS

T: LAN jack
B: USB ports

COM Port

CMI

9880L

J1394_2

2-1

Hardware Setup

Chapter 2. Hardware Setup

This chapter tells you how to install the CPU, memory modules,
and expansion cards, as well as how to setup the jumpers on the
mainboard. Also, it provides the instructions on connecting the periph­eral devices, such as the mouse, keyboard, etc.

While doing the installation, be careful in holding the compo­nents and follow the installation procedures.

Hardware Setup

2-2

MS-7058 ATX Mainboard

Quick Components Guide

BATT

+

DDR DIMMs, p.2-7

JFP2, p.2-17

Back Panel
I/O, p.2-10

CPUFAN1, p.2-9

ATX1, p.2-9

JFP1, p.2-17

PCI Slots 1~3,

p.2-22

JUSB1, JUSB2, p.2-19

JAUD1, p.2-18

SATA1~SATA4,

p.2-16

IDE1, p.2-15

SYSFAN1, p.2-14

FDD1, p.2-14

JBAT1, p.2-22

JPW1, p.2-9

PCI Express x1,

p.2-22

PCI Express x16,

p.2-22

JCD1, p.2-18

PWRFAN1, p.2-14

J1394_1~J1934_3,

p.2-18

2-3

Hardware Setup

Central Processing Unit: CPU

The mainboard supports Intel® Pentium 4 Prescott processor. The mainboard
uses a CPU socket called LGA775. When you are installing the CPU, make sure to
install the cooler to prevent overheating. If you do not have the CPU cooler,
contact your dealer to purchase and install them before turning on the computer.

Introduction to LGA 775 CPU

The surface of LGA 775 CPU.
Remember to apply some silicone
heat transfer compound on it for
better heat dispersion.

Y ellow triangle is the Pin 1 indicator

The pin-pad side of LGA 775
CPU.

Y ellow triangle is the Pin 1 indicator

Alignment Key Alignment Key

MSI Reminds You...

Overheating

Overheating will seriously damage the CPU and system, always make
sure the cooling fan can work properly to protect the CPU from
overheating.

Replacing the CPU

While replacing the CPU, always turn off the ATX power supply or
unplug the power supply’s power cord from grounded outlet first to
ensure the safety of CPU.

2-4

MS-7058 ATX Mainboard

CPU & Cooler Installation

When you are installing the CPU, make sure the CPU has a cooler at-

tached on the top to prevent overheating. If you do not have the cooler, contact

your dealer to purchase and install them before turning on the computer. Meanwhile,
do not forget to apply some silicon heat transfer compound on CPU before installing
the heat sink/cooler fan for better heat dispersion.

Follow the steps below to install the CPU & cooler correctly. Wrong installation

will cause the damage of your CPU & mainboard.

1. The CPU has a land side cover on the
bottom to protect the CPU contact from
damage. Rotate it to make the pin 1
indicator (yellow triangle) in the right­bottom corner.

2. T ake out the accompanying CPU Clip
and rotate it for the same direction
as the CPU (Pin 1 indicator, the red
triangle is in the left-bottom corner).

3. Align the 3 points (the Pin 1 indicator
and the two alignment keys) of both
the CPU and the CPU Clip, and use your
4 fingers to push the CPU Clip down to
clip them (the CPU clip is up and the
CPU is down) together.

4. The land side cover now is
removed.

land side cover

MSI Reminds You...

1. Confirm if your CPU cooler is firmly installed before turning on your
system.

2.Do not touch the CPU socket pins to avoid damaging.

3. The availability of the CPU land side cover depends on your CPU
packing.

2-5

Hardware Setup

5. The CPU has a plastic cap on it to
protect the contact from damage.
Before you have installed the CPU,
always cover it to protect the socket
pin.

6. Remove the cap from lever hinge side
(as the arrow shows).

7. The pins of socket reveal. Then lift
up the load lever.

8. Lift the load lever up and open the
load plate.

9. Correctly align the red triangle of
CPU clip with the CPU chamfer, the
red arrow with the left-side socket
edge, and the red spot to the hook
of the socket.

10.Put the whole module onto the CPU
socket.

2-6

MS-7058 ATX Mainboard

11. Push down the CPU hardly to install
the CPU into the socket housing
frame.

12.Visually inspect if the CPU is seated
well into the socket, then remove the
CPU Clip with 2 fingers. Then cover
the load plate onto the package.

13. Press down the load lever lightly
onto the load plate, and then se­cure the lever with the hook under
retention tab.

14. Align the holes on the mainboard with
the cooler. Push down the cooler until
its four clips get wedged into the holes
of the mainboard.

16. Turn over the mainboard to confirm

that the clip-ends are correctly
inserted.

15. Press the four hooks down to fas­ten the cooler. Then rotate the lock­ing switch (refer to the correct di­rection marked on it) to lock the
hooks.

locking

switch

MSI Reminds You...

1. Check the information in PC Health Status of H/W Monitor in BIOS
(refer to p.3-20 for details) for the CPU temperature.

2. Whenever CPU is not installed, always protect your CPU socket pin
with the plastic cap covered (shown in Figure 1) to avoid damaging.

3. Please note that the mating/unmating durability of the CPU is 20 cycles.
Therefore we suggest you do not plug/unplug the CPU too often.

2-7

Hardware Setup

Memory

The mainboard provides 2 slots for 184-pin DDR1 DIMM (Double In-Line Memory

Module) modules which supports the memory size up to 2GB.

Introduction to DDR SDRAM

DDR1 SDRAM is similar to conventional SDRAM, but doubles the rate by

transferring data twice per cycle. It uses 2.5 volts, and requires 184-pin DIMM modules.

2-8

MS-7058 ATX Mainboard

Installing DDR Modules

1. The DDR DIMM has only one notch on the center of module. The module will
only fit in the right orientation.

2. Insert the DIMM memory module vertically into the DIMM slot. Then push it in
until the golden finger on the memory module is deeply inserted in the socket.

3. The plastic clip at each side of the DIMM slot will automatically close.

Volt

Notch

MSI Reminds You...

You can barely see the golden finger if the module is properly in­serted in the socket.

DIMM2 (DDR1) DIMM2 (DDR1) System Density

128MB~1GB 128MB~1GB *

128MB~1GB 128MB~1GB *

128MB~1GB 128MB~1GB 256MB~2GB **

*: single-channel **: dual-channel

Memory Module Population Rules

Install at least one DIMM module on the slots. Each DIMM slot supports up to a

maximum size of 1GB. Users can install either single- or double-sided modules to
meet their own needs. While using dual-channel DDR function, it is available for you
to install memory modules with different sizes, which will run in “asymmetric mode”.
However, it is strongly recommended that you install same-size memory modules for
better performance, which runs in “interleaved mode”.

Please refer to the following table for the available memory populations.

Other combination may cause damage to your mainboard.